You are not logged in.
Pages: 1
I have installed arch on a lenovo ideapad s10e.
I am struggling to make the wireless work.
The laptop has a broadcom 4312 card. I have tried to install the b43 driver but it doesn't work.
So I have followed the instructions on this page: http://wiki.archlinux.org/index.php/Broadcom_BCM4312 and the card is recognised, but if I try to iwlist scan it says
wlan0 Failed to read scan data : Invalid argument
I've tried various solutions found on google but with no success.
Any suggestions?
Offline
You are missing the firmware obviously, and that page doesn't say a damn thing about it. This is the page you want to read http://wiki.archlinux.org/index.php/Wireless#b43
You need to install an RTFM interface.
Offline
I have a S10e myself, and this is the driver I'm using: http://aur.archlinux.org/packages.php?ID=19514
Offline
Installing the b43 driver was the first thing I did, but it didn't work.
I have a S10e myself, and this is the driver I'm using: http://aur.archlinux.org/packages.php?ID=19514
this is what I am using now, and I get that error.
Last edited by katzen (2010-06-27 17:06:00)
Offline
What is your setup, other than having installed the broadcom-wl driver from AUR?
I use nm-applet for managing networks (network manager, in other words).
This is what my daemons array in /etc/rc.conf looks like
DAEMONS=(syslog-ng hal alsa cpufreq !network networkmanager netfs crond @cups @laptop-mode slim)
... this is the modules array
MODULES=(wl acpi-cpufreq cpufreq_conservative cpufreq_powersave !snd-pcsp !snd-pcspkr !pcspkr !snd-pcm-oss)
... and this is my interfaces array
INTERFACES=(!eth0 !wlan0)
Offline
These are my modules:
MODULES=(lib80211_crypt_tkip wl acpi-cpufreq cpufreq_ondemand cpufreq_powersave !b43 !ssb)
and the daemons:
DAEMONS=(syslog-ng acpid laptop-mode network netfs crond)
I have eth0 only in INTERFACES.
I tried to use wicd as well, but it doesn't find any networks as expected...
Last edited by katzen (2010-06-27 19:37:35)
Offline
The newer kernels identify broadcom chips by default. So your wlan interface should show when you run ifconfig, even without drivers. If it isnt showing, then your wifi is powered off.
Offline
The newer kernels identify broadcom chips by default. So your wlan interface should show when you run ifconfig, even without drivers. If it isnt showing, then your wifi is powered off.
As I stated in the first post, my wlan interface *is* recognized.
Howere I can't use it.
Offline
My suggestion would be to try using NetworkManager instead of the network daemon, and removing the lib80211_crypt_tkip from the modules array (the wireless setup on my machine seems to run just fine without it). Also, do you know for certain that the hardware actually works -- that is, does wifi work under windows, or when booting from a Ubuntu Live CD or something similar?
It's been a while since my last fresh install, but I remember how frustrating it was trying to get netcfg to work before just giving up and installing the less minimalist NetworkManager. Wifi can be a real pain under Linux, and having a netbook that does not do the "net" part is kind of frustrating.
Offline
are you shure that no killswitch is active ?
i had a similar problem with the s10e of my girlfriend some time ago and with activ killswitch ifconfig and iwconfig also listen the device
you could check with rfkill listen
Offline
are you shure that no killswitch is active ?
i had a similar problem with the s10e of my girlfriend some time ago and with activ killswitch ifconfig and iwconfig also listen the device
you could check with rfkill listen
Uhm if I try to use rfkill it says "Can't open RFKILL control device: no such file or directory"
There is no /dev/rfkill, maybe the kernel is compiled without support for it?
Offline
Pages: 1