Arch Linux

slackcub

Member

Registered: 2009-03-14

Posts: 144

USB issue with webcam, device descriptor read/64, error -110

I'm trying to use a camera (Panasonic HM-TA2) that I recently got as a webcam.  It has both video and audio available by the USB.  When I plug it in, though, I get the following output from dmesg:

[  350.600081] usb 2-2: new high speed USB device number 8 using ehci_hcd
[  350.728110] uvcvideo: Found UVC 1.00 device HM-TA2 (04da:2439)
[  352.229452] usbcore: registered new interface driver snd-usb-audio
[  405.246759] usb 2-2: reset high speed USB device number 8 using ehci_hcd
[  420.353462] usb 2-2: device descriptor read/64, error -110
[  435.563456] usb 2-2: device descriptor read/64, error -110
[  435.773458] usb 2-2: reset high speed USB device number 8 using ehci_hcd
[  450.880392] usb 2-2: device descriptor read/64, error -110
[  466.090514] usb 2-2: device descriptor read/64, error -110
[  466.304243] usb 2-2: reset high speed USB device number 8 using ehci_hcd
[  476.710069] usb 2-2: device not accepting address 8, error -110
[  476.816787] usb 2-2: reset high speed USB device number 8 using ehci_hcd
[  487.223295] usb 2-2: device not accepting address 8, error -110
[  487.223372] usb 2-2: USB disconnect, device number 8
[  487.223674] ioctl32(skype:1401): Unknown cmd fd(0) cmd(80685600){t:'V';sz:104} arg(f54e7134) on pipe:[8206]
[  487.330060] usb 2-2: new high speed USB device number 9 using ehci_hcd
[  489.325268] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
[  502.436751] usb 2-2: device descriptor read/64, error -110
[  517.646721] usb 2-2: device descriptor read/64, error -110
[  517.856749] usb 2-2: new high speed USB device number 10 using ehci_hcd
[  532.963354] usb 2-2: device descriptor read/64, error -110
[  548.173384] usb 2-2: device descriptor read/64, error -110
[  548.383387] usb 2-2: new high speed USB device number 11 using ehci_hcd
[  558.790039] usb 2-2: device not accepting address 11, error -110
[  558.896720] usb 2-2: new high speed USB device number 12 using ehci_hcd
[  569.303372] usb 2-2: device not accepting address 12, error -110
[  569.303396] hub 2-0:1.0: unable to enumerate USB device on port 2
[  569.686749] usb 5-2: new full speed USB device number 3 using ohci_hcd
[  584.816736] usb 5-2: device descriptor read/64, error -110
[  600.050008] usb 5-2: device descriptor read/64, error -110
[  600.283417] usb 5-2: new full speed USB device number 4 using ohci_hcd
[  615.413357] usb 5-2: device descriptor read/64, error -110
[  630.646744] usb 5-2: device descriptor read/64, error -110
[  630.880045] usb 5-2: new full speed USB device number 5 using ohci_hcd
[  641.286658] usb 5-2: device not accepting address 5, error -110
[  641.416700] usb 5-2: new full speed USB device number 6 using ohci_hcd
[  651.823382] usb 5-2: device not accepting address 6, error -110
[  651.823402] hub 5-0:1.0: unable to enumerate USB device on port 2

If I try leaving it plugged in at bootup, udev hangs for about 30 seconds, and I am unable to use my USB mouse for a couple minutes.  I tried searching around and it seems to be a common problem, but usually with external drives.  The thing that seems to work for most folks is unplugging the computer, but that's not really an option for me as this is on my laptop.  If anyone has any ideas, I'd be very grateful!

David

Last edited by slackcub (2012-01-05 05:22:23)