IDE DVD drive problem

Triston J. Taylor · 2012-02-08 21:10:03

I would like to bump this. I have an IDE CD/DVD multi-writer that keeps showing up as /dev/sr0. The main system storage device is however SATA (Gen. II) running on Intel's AHCI. The DVD super multi drive is the only IDE device in the system and it is the master IDE device by cable select jumper config. it is connected to the last ribbon slot on the cable. The drive is about four years old but its just been sitting on a shelf for most of that time. I reckon it has less than 10 hours runtime on it if that.

I'm no linux guru but I'm pretty sure it should be showing up as /dev/hdX. It will read and auto mount cd's under /media/$DISK_LABEL$ but dvd media are not detected at all. Yes, the bios will load and boot from a DVD. I have been wrestling this for near two weeks on my own. Can anyone help debug this?

* edits reflect typo correction.

Last edited by Triston J. Taylor (2012-02-08 21:19:40)

Gusar · 2012-02-08 21:16:09

Triston J. Taylor wrote:

I'm no linux guru but I'm pretty sure it should be showing up as /dev/hdX.

Uff, no. /dev/hdX has been gone for a loooooooong time now. /dev/sr0 is fully correct.

Look into whatever you're using for automounting. Also check dmesg after you've inserted a dvd.

Triston J. Taylor · 2012-02-08 21:31:01

$ dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0-ARCH (tobias@T-POWA-LX) (gcc version 4.6.1 (GCC) ) #1 SMP PREEMPT Wed Aug 17 20:24:07 UTC 2011
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[    0.000000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000cfee0000 (usable)
[    0.000000]  BIOS-e820: 00000000cfee0000 - 00000000cfee3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000cfee3000 - 00000000cfef0000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000cfef0000 - 00000000cff00000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[    0.000000] DMI 2.4 present.
[    0.000000] DMI: Foxconn 975X7AB/975X7AB, BIOS 6.00 PG 08/16/2008
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0xcfee0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CDFFF write-protect
[    0.000000]   CE000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-through
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FF0000000 write-back
[    0.000000]   3 base 0CFF00000 mask FFFF00000 uncachable
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] found SMP MP-table at [c00f4fd0] f4fd0
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ bfb000-c00000
[    0.000000] RAMDISK: 7fdd6000 - 7fff0000
[    0.000000] Allocated new RAMDISK: 375e4000 - 377fd2c0
[    0.000000] Move RAMDISK from 000000007fdd6000 - 000000007ffef2bf to 375e4000 - 377fd2bf
[    0.000000] ACPI: RSDP 000f8fa0 00014 (v00 IntelR)
[    0.000000] ACPI: RSDT cfee3040 0003C (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: FACP cfee30c0 00074 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: DSDT cfee3180 045DF (v01 INTELR AWRDACPI 00001000 MSFT 0100000E)
[    0.000000] ACPI: FACS cfee0000 00040
[    0.000000] ACPI: _HPT cfee78c0 00038 (v01 IntelR AWRDACPI 42302E31 AWRD 00000098)
[    0.000000] ACPI: MCFG cfee7940 0003C (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: APIC cfee77c0 00084 (v01 IntelR AWRDACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: SSDT cfee79c0 0015C (v01  PmRef  Cpu0Ist 00003000 INTL 20040311)
[    0.000000] ACPI: SSDT cfee7e50 002F1 (v01  PmRef    CpuPm 00003000 INTL 20040311)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 2438MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x000cfee0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000cfee0
[    0.000000] On node 0 totalpages: 851567
[    0.000000] free_area_init_node: node 0, pgdat c05adc80, node_mem_map f5be3200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 4878 pages used for memmap
[    0.000000]   HighMem zone: 619476 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at cff00000 (gap: cff00000:10100000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 12 pages/cpu @f5400000 s25472 r0 d23680 u1048576
[    0.000000] pcpu-alloc: s25472 r0 d23680 u1048576 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 844913
[    0.000000] Kernel command line: root=/dev/disk/by-uuid/b5d3d4c9-7476-4c53-a4dc-8518ece351d7 ro vga=773
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] allocated 13626624 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (000377fe:000cfee0)
[    0.000000] Memory: 3356844k/3406720k available (3415k kernel code, 49424k reserved, 1406k data, 500k init, 2497416k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff16000 - 0xfffff000   ( 932 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc05b6000 - 0xc0633000   ( 500 kB)
[    0.000000]       .data : 0xc0455f95 - 0xc05b5980   (1406 kB)
[    0.000000]       .text : 0xc0100000 - 0xc0455f95   (3415 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:512
[    0.000000] CPU 0 irqstacks, hard=f400e000 soft=f4020000
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 3006.924 MHz processor.
[    0.006670] Calibrating delay loop (skipped), value calculated using timer frequency.. 6016.42 BogoMIPS (lpj=10023080)
[    0.006676] pid_max: default: 32768 minimum: 301
[    0.006727] Security Framework initialized
[    0.006733] AppArmor: AppArmor disabled by boot time parameter
[    0.006762] Mount-cache hash table entries: 512
[    0.007010] Initializing cgroup subsys cpuacct
[    0.007027] Initializing cgroup subsys memory
[    0.007041] Initializing cgroup subsys devices
[    0.007044] Initializing cgroup subsys freezer
[    0.007047] Initializing cgroup subsys net_cls
[    0.007050] Initializing cgroup subsys blkio
[    0.007107] CPU: Physical Processor ID: 0
[    0.007110] CPU: Processor Core ID: 0
[    0.007113] mce: CPU supports 4 MCE banks
[    0.007127] CPU0: Thermal monitoring enabled (TM1)
[    0.007132] using mwait in idle threads.
[    0.011112] ACPI: Core revision 20110413
[    0.016697] ftrace: allocating 15363 entries in 31 pages
[    0.020056] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.020381] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.053813] CPU0: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
[    0.056663] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[    0.056663] ... version:                0
[    0.056663] ... bit width:              40
[    0.056663] ... generic registers:      18
[    0.056663] ... value mask:             000000ffffffffff
[    0.056663] ... max period:             0000007fffffffff
[    0.056663] ... fixed-purpose events:   0
[    0.056663] ... event mask:             000000000003ffff
[    0.073413] NMI watchdog enabled, takes one hw-pmu counter.
[    0.100020] CPU 1 irqstacks, hard=f40b4000 soft=f40b6000
[    0.100024] Booting Node   0, Processors  #1
[    0.100029] smpboot cpu 1: start_ip = 9b000
[    0.009999] Initializing CPU#1
[    0.196679] NMI watchdog enabled, takes one hw-pmu counter.
[    0.203331] Brought up 2 CPUs
[    0.203337] Total of 2 processors activated (12031.28 BogoMIPS).
[    0.204495] devtmpfs: initialized
[    0.204495] PM: Registering ACPI NVS region at cfee0000 (12288 bytes)
[    0.205042] print_constraints: dummy: 
[    0.205110] NET: Registered protocol family 16
[    0.206796] ACPI: bus type pci registered
[    0.206909] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.206914] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.206916] PCI: Using MMCONFIG for extended config space
[    0.206919] PCI: Using configuration type 1 for base access
[    0.207630] bio: create slab <bio-0> at 0
[    0.207934] ACPI: EC: Look up EC in DSDT
[    0.216001] ACPI Warning: Incorrect checksum in table [_HPT] - 0x1C, should be 0x02 (20110413/tbutils-314)
[    0.216221] ACPI: SSDT cfee7dc0 00087 (v01  PmRef  Cpu1Ist 00003000 INTL 20040311)
[    0.216514] ACPI: Dynamic OEM Table Load:
[    0.216519] ACPI: SSDT   (null) 00087 (v01  PmRef  Cpu1Ist 00003000 INTL 20040311)
[    0.216815] ACPI: Interpreter enabled
[    0.216822] ACPI: (supports S0 S1 S3 S4 S5)
[    0.216853] ACPI: Using IOAPIC for interrupt routing
[    0.219944] ACPI Error: [HPTF] Namespace lookup failure, AE_NOT_FOUND (20110413/psargs-359)
[    0.219954] ACPI Error: Method parse/execution failed [\_SB_.PCI0.PX40._HPT._STA] (Node f4030150), AE_NOT_FOUND (20110413/psparse-536)
[    0.220006] ACPI Error: [HPTF] Namespace lookup failure, AE_NOT_FOUND (20110413/psargs-359)
[    0.220015] ACPI Error: Method parse/execution failed [\_SB_.PCI0.PX40._HPT._STA] (Node f4030150), AE_NOT_FOUND (20110413/psparse-536)
[    0.223623] ACPI: No dock devices found.
[    0.223626] HEST: Table not found.
[    0.223631] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.223715] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.223900] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    0.223905] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    0.223909] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.223912] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff]
[    0.223916] pci_root PNP0A08:00: host bridge window [mem 0xcff00000-0xfebfffff]
[    0.223934] pci 0000:00:00.0: [8086:277c] type 0 class 0x000600
[    0.223990] pci 0000:00:01.0: [8086:277d] type 1 class 0x000604
[    0.224036] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.224041] pci 0000:00:01.0: PME# disabled
[    0.224095] pci 0000:00:1b.0: [8086:27d8] type 0 class 0x000403
[    0.224115] pci 0000:00:1b.0: reg 10: [mem 0xfdff8000-0xfdffbfff 64bit]
[    0.224182] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.224187] pci 0000:00:1b.0: PME# disabled
[    0.224211] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
[    0.224279] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.224284] pci 0000:00:1c.0: PME# disabled
[    0.224315] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
[    0.224363] pci 0000:00:1d.0: reg 20: [io  0xfc00-0xfc1f]
[    0.224400] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
[    0.224449] pci 0000:00:1d.1: reg 20: [io  0xf800-0xf81f]
[    0.224485] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
[    0.224533] pci 0000:00:1d.2: reg 20: [io  0xf400-0xf41f]
[    0.224568] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
[    0.224616] pci 0000:00:1d.3: reg 20: [io  0xf000-0xf01f]
[    0.224659] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
[    0.224680] pci 0000:00:1d.7: reg 10: [mem 0xfdfff000-0xfdfff3ff]
[    0.224755] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.224761] pci 0000:00:1d.7: PME# disabled
[    0.224780] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[    0.224848] pci 0000:00:1f.0: [8086:27b8] type 0 class 0x000601
[    0.224944] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.224958] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 000f)
[    0.224997] pci 0000:00:1f.1: [8086:27df] type 0 class 0x000101
[    0.225013] pci 0000:00:1f.1: reg 10: [io  0x0000-0x0007]
[    0.225025] pci 0000:00:1f.1: reg 14: [io  0x0000-0x0003]
[    0.225036] pci 0000:00:1f.1: reg 18: [io  0x0000-0x0007]
[    0.225047] pci 0000:00:1f.1: reg 1c: [io  0x0000-0x0003]
[    0.225059] pci 0000:00:1f.1: reg 20: [io  0xec00-0xec0f]
[    0.225102] pci 0000:00:1f.2: [8086:27c1] type 0 class 0x000106
[    0.225121] pci 0000:00:1f.2: reg 10: [io  0xe800-0xe807]
[    0.225131] pci 0000:00:1f.2: reg 14: [io  0xe400-0xe403]
[    0.225142] pci 0000:00:1f.2: reg 18: [io  0xe000-0xe007]
[    0.225152] pci 0000:00:1f.2: reg 1c: [io  0xdc00-0xdc03]
[    0.225162] pci 0000:00:1f.2: reg 20: [io  0xd800-0xd80f]
[    0.225172] pci 0000:00:1f.2: reg 24: [mem 0xfdffe000-0xfdffe3ff]
[    0.225205] pci 0000:00:1f.2: PME# supported from D3hot
[    0.225210] pci 0000:00:1f.2: PME# disabled
[    0.225232] pci 0000:00:1f.3: [8086:27da] type 0 class 0x000c05
[    0.225291] pci 0000:00:1f.3: reg 20: [io  0x0500-0x051f]
[    0.225376] pci 0000:01:00.0: [1002:94c3] type 0 class 0x000300
[    0.225396] pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.225411] pci 0000:01:00.0: reg 18: [mem 0xfdde0000-0xfddeffff 64bit]
[    0.225421] pci 0000:01:00.0: reg 20: [io  0xac00-0xacff]
[    0.225439] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.225463] pci 0000:01:00.0: supports D1 D2
[    0.225489] pci 0000:01:00.1: [1002:aa10] type 0 class 0x000403
[    0.225507] pci 0000:01:00.1: reg 10: [mem 0xfddfc000-0xfddfffff 64bit]
[    0.225566] pci 0000:01:00.1: supports D1 D2
[    0.230009] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.230015] pci 0000:00:01.0:   bridge window [io  0xa000-0xafff]
[    0.230021] pci 0000:00:01.0:   bridge window [mem 0xfdd00000-0xfddfffff]
[    0.230029] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.230110] pci 0000:02:00.0: [11ab:4364] type 0 class 0x000200
[    0.230137] pci 0000:02:00.0: reg 10: [mem 0xfdafc000-0xfdafffff 64bit]
[    0.230152] pci 0000:02:00.0: reg 18: [io  0xcc00-0xccff]
[    0.230201] pci 0000:02:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.230246] pci 0000:02:00.0: supports D1 D2
[    0.230249] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.230256] pci 0000:02:00.0: PME# disabled
[    0.236675] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.236682] pci 0000:00:1c.0:   bridge window [io  0xc000-0xcfff]
[    0.236689] pci 0000:00:1c.0:   bridge window [mem 0xfda00000-0xfdafffff]
[    0.236698] pci 0000:00:1c.0:   bridge window [mem 0xfde00000-0xfdefffff 64bit pref]
[    0.236746] pci 0000:03:00.0: [104c:8023] type 0 class 0x000c00
[    0.236768] pci 0000:03:00.0: reg 10: [mem 0xfdcff000-0xfdcff7ff]
[    0.236781] pci 0000:03:00.0: reg 14: [mem 0xfdcf8000-0xfdcfbfff]
[    0.236852] pci 0000:03:00.0: supports D1 D2
[    0.236855] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot
[    0.236861] pci 0000:03:00.0: PME# disabled
[    0.236914] pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)
[    0.236919] pci 0000:00:1e.0:   bridge window [io  0xb000-0xbfff]
[    0.236925] pci 0000:00:1e.0:   bridge window [mem 0xfdc00000-0xfdcfffff]
[    0.236932] pci 0000:00:1e.0:   bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
[    0.236936] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.236940] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.236944] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.236947] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.236951] pci 0000:00:1e.0:   bridge window [mem 0xcff00000-0xfebfffff] (subtractive decode)
[    0.236968] pci_bus 0000:00: on NUMA node 0
[    0.236973] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.237142] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[    0.237212] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[    0.237428]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.237433]  pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[    0.237435] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.248187] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 9 10 *11 12 14 15)
[    0.248265] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 9 10 11 12 14 *15)
[    0.248341] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 *9 10 11 12 14 15)
[    0.248417] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 9 10 11 12 14 *15)
[    0.248493] ACPI: PCI Interrupt Link [LNKE] (IRQs 5 9 10 11 12 14 15) *0, disabled.
[    0.248571] ACPI: PCI Interrupt Link [LNKF] (IRQs 5 9 *10 11 12 14 15)
[    0.248647] ACPI: PCI Interrupt Link [LNK0] (IRQs 5 9 10 11 12 14 15) *0, disabled.
[    0.248725] ACPI: PCI Interrupt Link [LNK1] (IRQs *5 9 10 11 12 14 15)
[    0.248864] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.248871] vgaarb: loaded
[    0.248873] vgaarb: bridge control possible 0000:01:00.0
[    0.249016] PCI: Using ACPI for IRQ routing
[    0.256487] PCI: pci_cache_line_size set to 64 bytes
[    0.256577] reserve RAM buffer: 000000000009f400 - 000000000009ffff 
[    0.256581] reserve RAM buffer: 00000000cfee0000 - 00000000cfffffff 
[    0.256752] NetLabel: Initializing
[    0.256756] NetLabel:  domain hash size = 128
[    0.256758] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.256776] NetLabel:  unlabeled traffic allowed by default
[    0.256873] hpet clockevent registered
[    0.256877] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.256883] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.256890] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.266677] Switching to clocksource hpet
[    0.269888] Switched to NOHz mode on CPU #0
[    0.269938] Switched to NOHz mode on CPU #1
[    0.275589] pnp: PnP ACPI init
[    0.275613] ACPI: bus type pnp registered
[    0.275738] pnp 00:00: [bus 00-ff]
[    0.275743] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.275747] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.275751] pnp 00:00: [io  0x0d00-0xffff window]
[    0.275755] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.275758] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[    0.275762] pnp 00:00: [mem 0xcff00000-0xfebfffff window]
[    0.275844] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.275933] pnp 00:01: [io  0x0010-0x001f]
[    0.275937] pnp 00:01: [io  0x0022-0x003f]
[    0.275940] pnp 00:01: [io  0x0044-0x005f]
[    0.275946] pnp 00:01: [io  0x0062-0x0063]
[    0.275949] pnp 00:01: [io  0x0065-0x006f]
[    0.275951] pnp 00:01: [io  0x0074-0x007f]
[    0.275954] pnp 00:01: [io  0x0091-0x0093]
[    0.275957] pnp 00:01: [io  0x00a2-0x00bf]
[    0.275960] pnp 00:01: [io  0x00e0-0x00ef]
[    0.275963] pnp 00:01: [io  0x04d0-0x04d1]
[    0.275965] pnp 00:01: [io  0x0290-0x0295]
[    0.275968] pnp 00:01: [io  0x0290-0x0297]
[    0.275971] pnp 00:01: [io  0x0880-0x088f]
[    0.276053] system 00:01: [io  0x04d0-0x04d1] has been reserved
[    0.276057] system 00:01: [io  0x0290-0x0295] has been reserved
[    0.276061] system 00:01: [io  0x0290-0x0297] could not be reserved
[    0.276065] system 00:01: [io  0x0880-0x088f] has been reserved
[    0.276071] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.276090] pnp 00:02: [dma 4]
[    0.276094] pnp 00:02: [io  0x0000-0x000f]
[    0.276098] pnp 00:02: [io  0x0080-0x0090]
[    0.276101] pnp 00:02: [io  0x0094-0x009f]
[    0.276106] pnp 00:02: [io  0x00c0-0x00df]
[    0.276154] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.276173] pnp 00:03: [io  0x0070-0x0073]
[    0.276186] pnp 00:03: [irq 8]
[    0.276233] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.276248] pnp 00:04: [io  0x0061]
[    0.276293] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.276308] pnp 00:05: [io  0x00f0-0x00ff]
[    0.276316] pnp 00:05: [irq 13]
[    0.276361] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.276548] pnp 00:06: [io  0x03f0-0x03f5]
[    0.276552] pnp 00:06: [io  0x03f7]
[    0.276560] pnp 00:06: [irq 6]
[    0.276563] pnp 00:06: [dma 2]
[    0.276628] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.276890] pnp 00:07: [io  0x03f8-0x03ff]
[    0.276899] pnp 00:07: [irq 4]
[    0.276989] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.277322] pnp 00:08: [io  0x02f8-0x02ff]
[    0.277329] pnp 00:08: [irq 3]
[    0.277409] pnp 00:08: Plug and Play ACPI device, IDs PNP0510 (active)
[    0.277681] pnp 00:09: [io  0x0378-0x037f]
[    0.277689] pnp 00:09: [irq 7]
[    0.277765] pnp 00:09: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.277990] pnp 00:0a: [io  0x0060]
[    0.277994] pnp 00:0a: [io  0x0064]
[    0.278002] pnp 00:0a: [irq 1]
[    0.278050] pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.278063] ACPI Error: [HPTF] Namespace lookup failure, AE_NOT_FOUND (20110413/psargs-359)
[    0.278072] ACPI Error: Method parse/execution failed [\_SB_.PCI0.PX40._HPT._STA] (Node f4030150), AE_NOT_FOUND (20110413/psparse-536)
[    0.278096] pnp 00:0b: [mem 0xfed00000-0xfed003ff]
[    0.278145] pnp 00:0b: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.278176] pnp 00:0c: [io  0x0400-0x04bf]
[    0.278247] system 00:0c: [io  0x0400-0x04bf] has been reserved
[    0.278252] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.278282] pnp 00:0d: [mem 0xffb80000-0xffbfffff]
[    0.278332] pnp 00:0d: Plug and Play ACPI device, IDs INT0800 (active)
[    0.278629] pnp 00:0e: [mem 0xe0000000-0xefffffff]
[    0.278718] system 00:0e: [mem 0xe0000000-0xefffffff] has been reserved
[    0.278724] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.278904] pnp 00:0f: [mem 0x000d1000-0x000d3fff]
[    0.278911] pnp 00:0f: [mem 0x000f0000-0x000f7fff]
[    0.278914] pnp 00:0f: [mem 0x000f8000-0x000fbfff]
[    0.278917] pnp 00:0f: [mem 0x000fc000-0x000fffff]
[    0.278920] pnp 00:0f: [mem 0xcfee0000-0xcfefffff]
[    0.278923] pnp 00:0f: [mem 0x00000000-0x0009ffff]
[    0.278926] pnp 00:0f: [mem 0x00100000-0xcfedffff]
[    0.278929] pnp 00:0f: [mem 0xfec00000-0xfec00fff]
[    0.278932] pnp 00:0f: [mem 0xfed13000-0xfed1dfff]
[    0.278935] pnp 00:0f: [mem 0xfed20000-0xfed8ffff]
[    0.278938] pnp 00:0f: [mem 0xfee00000-0xfee00fff]
[    0.278941] pnp 00:0f: [mem 0xffb00000-0xffb7ffff]
[    0.278944] pnp 00:0f: [mem 0xfff00000-0xffffffff]
[    0.278947] pnp 00:0f: [mem 0x000e0000-0x000effff]
[    0.279046] system 00:0f: [mem 0x000d1000-0x000d3fff] has been reserved
[    0.279050] system 00:0f: [mem 0x000f0000-0x000f7fff] could not be reserved
[    0.279054] system 00:0f: [mem 0x000f8000-0x000fbfff] could not be reserved
[    0.279058] system 00:0f: [mem 0x000fc000-0x000fffff] could not be reserved
[    0.279062] system 00:0f: [mem 0xcfee0000-0xcfefffff] could not be reserved
[    0.279066] system 00:0f: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.279069] system 00:0f: [mem 0x00100000-0xcfedffff] could not be reserved
[    0.279073] system 00:0f: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.279077] system 00:0f: [mem 0xfed13000-0xfed1dfff] has been reserved
[    0.279081] system 00:0f: [mem 0xfed20000-0xfed8ffff] has been reserved
[    0.279085] system 00:0f: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.279088] system 00:0f: [mem 0xffb00000-0xffb7ffff] has been reserved
[    0.279092] system 00:0f: [mem 0xfff00000-0xffffffff] has been reserved
[    0.279096] system 00:0f: [mem 0x000e0000-0x000effff] has been reserved
[    0.279101] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.279113] pnp: PnP ACPI: found 16 devices
[    0.279115] ACPI: ACPI bus type pnp unregistered
[    0.316479] PCI: max bus depth: 1 pci_try_num: 2
[    0.316512] pci 0000:01:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd1ffff pref]
[    0.316517] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.316522] pci 0000:00:01.0:   bridge window [io  0xa000-0xafff]
[    0.316527] pci 0000:00:01.0:   bridge window [mem 0xfdd00000-0xfddfffff]
[    0.316532] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.316540] pci 0000:02:00.0: BAR 6: assigned [mem 0xfde00000-0xfde1ffff pref]
[    0.316543] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[    0.316548] pci 0000:00:1c.0:   bridge window [io  0xc000-0xcfff]
[    0.316554] pci 0000:00:1c.0:   bridge window [mem 0xfda00000-0xfdafffff]
[    0.316559] pci 0000:00:1c.0:   bridge window [mem 0xfde00000-0xfdefffff 64bit pref]
[    0.316567] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
[    0.316571] pci 0000:00:1e.0:   bridge window [io  0xb000-0xbfff]
[    0.316577] pci 0000:00:1e.0:   bridge window [mem 0xfdc00000-0xfdcfffff]
[    0.316583] pci 0000:00:1e.0:   bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
[    0.316600] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.316606] pci 0000:00:01.0: setting latency timer to 64
[    0.316615] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.316620] pci 0000:00:1c.0: setting latency timer to 64
[    0.316629] pci 0000:00:1e.0: setting latency timer to 64
[    0.316634] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.316638] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.316641] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.316644] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[    0.316647] pci_bus 0000:00: resource 8 [mem 0xcff00000-0xfebfffff]
[    0.316651] pci_bus 0000:01: resource 0 [io  0xa000-0xafff]
[    0.316654] pci_bus 0000:01: resource 1 [mem 0xfdd00000-0xfddfffff]
[    0.316657] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.316661] pci_bus 0000:02: resource 0 [io  0xc000-0xcfff]
[    0.316679] pci_bus 0000:02: resource 1 [mem 0xfda00000-0xfdafffff]
[    0.316682] pci_bus 0000:02: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref]
[    0.316686] pci_bus 0000:03: resource 0 [io  0xb000-0xbfff]
[    0.316689] pci_bus 0000:03: resource 1 [mem 0xfdc00000-0xfdcfffff]
[    0.316692] pci_bus 0000:03: resource 2 [mem 0xfdb00000-0xfdbfffff 64bit pref]
[    0.316696] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7]
[    0.316699] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff]
[    0.316702] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[    0.316705] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000dffff]
[    0.316708] pci_bus 0000:03: resource 8 [mem 0xcff00000-0xfebfffff]
[    0.316756] NET: Registered protocol family 2
[    0.316849] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.317149] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.317726] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.318014] TCP: Hash tables configured (established 131072 bind 65536)
[    0.318016] TCP reno registered
[    0.318020] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.318031] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.318182] NET: Registered protocol family 1
[    1.650021] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[    1.650056] pci 0000:01:00.0: Boot video device
[    1.650071] PCI: CLS 64 bytes, default 64
[    1.650141] Unpacking initramfs...
[    1.697115] Freeing initrd memory: 2152k freed
[    1.698241] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[    1.698245] apm: disabled - APM is not SMP safe.
[    1.698448] audit: initializing netlink socket (disabled)
[    1.698462] type=2000 audit(1328659232.696:1): initialized
[    1.704270] highmem bounce pool size: 64 pages
[    1.704278] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.717109] VFS: Disk quotas dquot_6.5.2
[    1.717224] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.717366] msgmni has been set to 1682
[    1.717663] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.717707] io scheduler noop registered
[    1.717711] io scheduler deadline registered
[    1.717734] io scheduler cfq registered (default)
[    1.717904] pcieport 0000:00:01.0: setting latency timer to 64
[    1.717944] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    1.718013] pcieport 0000:00:1c.0: setting latency timer to 64
[    1.718057] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    1.718239] vesafb: mode is 1024x768x8, linelength=1024, pages=18
[    1.718243] vesafb: protected mode interface info at c000:9faa
[    1.718246] vesafb: pmi: set display start = c00ca04c, set palette = c00ca10a
[    1.718249] vesafb: scrolling: redraw
[    1.718252] vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
[    1.718519] vesafb: framebuffer at 0xd0000000, mapped to 0xf8080000, using 1536k, total 16384k
[    1.718591] fbcon: VESA VGA (fb0) is primary device
[    1.735214] Console: switching to colour frame buffer device 128x48
[    1.751742] fb0: VESA VGA frame buffer device
[    1.751796] ERST: Table is not found!
[    1.751818] isapnp: Scanning for PnP cards...
[    2.065075] isapnp: No Plug & Play device found
[    2.065178] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    2.085741] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    2.133878] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    2.300783] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    2.340516] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    2.340520] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    2.341251] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.341390] mousedev: PS/2 mouse device common for all mice
[    2.341509] rtc_cmos 00:03: RTC can wake from S4
[    2.341635] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    2.341663] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[    2.341700] cpuidle: using governor ladder
[    2.341704] cpuidle: using governor menu
[    2.342047] TCP cubic registered
[    2.342051] NET: Registered protocol family 17
[    2.342060] Registering the dns_resolver key type
[    2.342086] Using IPI No-Shortcut mode
[    2.342202] PM: Hibernation image not present or could not be loaded.
[    2.342211] registered taskstats version 1
[    2.347668] rtc_cmos 00:03: setting system clock to 2012-02-08 00:00:33 UTC (1328659233)
[    2.347738] Initializing network drop monitor service
[    2.347844] Freeing unused kernel memory: 500k freed
[    2.348119] Write protecting the kernel text: 3416k
[    2.348151] Write protecting the kernel read-only data: 1036k
[    2.368679] udevd[58]: starting version 173
[    2.431967] usbcore: registered new interface driver usbfs
[    2.432001] usbcore: registered new interface driver hub
[    2.443924] usbcore: registered new device driver usb
[    2.444923] SCSI subsystem initialized
[    2.460867] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.460913] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.460936] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    2.460941] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.460976] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    2.461004] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[    2.465663] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    2.465689] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000
[    2.466779] libata version 3.00 loaded.
[    2.480083] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    2.480299] hub 1-0:1.0: USB hub found
[    2.480307] hub 1-0:1.0: 8 ports detected
[    2.480424] ata_piix 0000:00:1f.1: version 2.13
[    2.480447] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    2.480493] ata_piix 0000:00:1f.1: setting latency timer to 64
[    2.483321] scsi0 : ata_piix
[    2.483996] scsi1 : ata_piix
[    2.484702] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xec00 irq 14
[    2.484706] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xec08 irq 15
[    2.484785] ahci 0000:00:1f.2: version 3.0
[    2.484807] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    2.484857] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
[    2.484937] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[    2.484942] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
[    2.484948] ahci 0000:00:1f.2: setting latency timer to 64
[    2.485726] ata2: port disabled. ignoring.
[    2.486049] scsi2 : ahci
[    2.486195] scsi3 : ahci
[    2.486314] scsi4 : ahci
[    2.486455] scsi5 : ahci
[    2.486653] ata3: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe100 irq 42
[    2.486658] ata4: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe180 irq 42
[    2.486662] ata5: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe200 irq 42
[    2.486666] ata6: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe280 irq 42
[    2.487289] uhci_hcd: USB Universal Host Controller Interface driver
[    2.487329] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.487339] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.487343] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.487357] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    2.487388] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fc00
[    2.487595] hub 2-0:1.0: USB hub found
[    2.487602] hub 2-0:1.0: 2 ports detected
[    2.487706] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.487714] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.487718] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.487729] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    2.487767] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000f800
[    2.487952] hub 3-0:1.0: USB hub found
[    2.487958] hub 3-0:1.0: 2 ports detected
[    2.488049] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    2.488057] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.488061] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.488071] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    2.488108] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000f400
[    2.488293] hub 4-0:1.0: USB hub found
[    2.488299] hub 4-0:1.0: 2 ports detected
[    2.488394] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    2.488402] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    2.488406] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    2.488416] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    2.488453] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000f000
[    2.488636] hub 5-0:1.0: USB hub found
[    2.488642] hub 5-0:1.0: 2 ports detected
[    2.643655] ata1.00: ATAPI: ATAPI   iHAP122   9, 6L0C, max UDMA/66
[    2.656865] ata1.00: configured for UDMA/66
[    2.658982] scsi 0:0:0:0: CD-ROM            ATAPI    iHAP122   9      6L0C PQ: 0 ANSI: 5
[    2.700025] Refined TSC clocksource calibration: 3006.818 MHz.
[    2.700033] Switching to clocksource tsc
[    2.786701] usb 1-1: new high speed USB device number 2 using ehci_hcd
[    2.806696] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.806718] ata4: SATA link down (SStatus 0 SControl 300)
[    2.806751] ata5: SATA link down (SStatus 0 SControl 300)
[    2.806779] ata6: SATA link down (SStatus 0 SControl 300)
[    2.807716] ata3.00: ATA-7: Hitachi HDS721616PLA380, P22OABEA, max UDMA/133
[    2.807722] ata3.00: 321672960 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.808897] ata3.00: configured for UDMA/133
[    2.809062] scsi 2:0:0:0: Direct-Access     ATA      Hitachi HDS72161 P22O PQ: 0 ANSI: 5
[    2.820177] sd 2:0:0:0: [sda] 321672960 512-byte logical blocks: (164 GB/153 GiB)
[    2.820258] sd 2:0:0:0: [sda] Write Protect is off
[    2.820262] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.820295] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.843326]  sda: sda1 sda2 sda3 sda4
[    2.843849] sd 2:0:0:0: [sda] Attached SCSI disk
[    2.847945] sr0: scsi3-mmc drive: 5x/5x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.847952] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.848312] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    3.257236] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[    3.323367] usb 2-2: new low speed USB device number 2 using uhci_hcd
[    3.713357] usb 3-1: new low speed USB device number 2 using uhci_hcd
[    4.407534] udevd[270]: starting version 180
[    4.612327] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    4.612337] ACPI: Power Button [PWRB]
[    4.612438] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    4.612444] ACPI: Power Button [PWRF]
[    4.619342] iTCO_vendor_support: vendor-support=0
[    4.630892] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[    4.631027] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
[    4.631145] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    4.637766] sky2: driver version 1.28
[    4.637802] sky2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.637815] sky2 0000:02:00.0: setting latency timer to 64
[    4.637846] sky2 0000:02:00.0: Yukon-2 EC Ultra chip revision 2
[    4.637954] sky2 0000:02:00.0: irq 43 for MSI/MSI-X
[    4.639105] sky2 0000:02:00.0: eth0: addr 00:15:58:5c:02:6a
[    4.647347] usbcore: registered new interface driver uas
[    4.652831] usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x03F0 pid 0x7411
[    4.652860] usbcore: registered new interface driver usblp
[    4.661661] thermal LNXTHERM:00: registered as thermal_zone0
[    4.661666] ACPI: Thermal Zone [THRM] (34 C)
[    4.662188] ACPI: Fan [FAN] (on)
[    4.663078] ACPI: acpi_idle registered with cpuidle
[    4.667396] parport_pc 00:09: reported by Plug and Play ACPI
[    4.667444] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[    4.734379] EDAC MC: Ver: 2.1.0
[    4.750939] ppdev: user-space parallel port driver
[    4.771239] intel_rng: FWH not detected
[    4.780974] Initializing USB Mass Storage driver...
[    4.781234] scsi6 : usb-storage 1-1:1.3
[    4.781446] usbcore: registered new interface driver usb-storage
[    4.781449] USB Mass Storage support registered.
[    4.782687] EDAC i82975x: ECC disabled on both channels.
[    4.790225] Floppy drive(s): fd0 is 1.44M
[    4.795742] input: PC Speaker as /devices/platform/pcspkr/input/input2
[    4.807696] FDC 0 is a post-1991 82077
[    4.845162] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    4.864970] Linux agpgart interface v0.103
[    4.893873] [drm] Initialized drm 1.1.0 20060810
[    4.895377] leds_ss4200: no LED devices found
[    4.907899] firewire_ohci 0000:03:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[    4.907908] firewire_ohci 0000:03:00.0: setting latency timer to 64
[    4.928550] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.928607] HDA Intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[    4.928639] HDA Intel 0000:00:1b.0: setting latency timer to 64
[    4.960097] firewire_ohci: Added fw-ohci device 0000:03:00.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
[    5.031458] [drm] radeon defaulting to kernel modesetting.
[    5.031462] [drm] radeon kernel modesetting enabled.
[    5.031509] checking generic (d0000000 1000000) vs hw (d0000000 10000000)
[    5.031513] fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
[    5.031580] Console: switching to colour dummy device 80x25
[    5.032244] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    5.032251] radeon 0000:01:00.0: setting latency timer to 64
[    5.032559] [drm] initializing kernel modesetting (RV610 0x1002:0x94C3 0x1787:0x2000).
[    5.032585] [drm] register mmio base: 0xFDDE0000
[    5.032587] [drm] register mmio size: 65536
[    5.032845] ATOM BIOS: 113
[    5.032873] radeon 0000:01:00.0: VRAM: 256M 0x0000000000000000 - 0x000000000FFFFFFF (256M used)
[    5.032877] radeon 0000:01:00.0: GTT: 512M 0x0000000010000000 - 0x000000002FFFFFFF
[    5.034100] [drm] Detected VRAM RAM=256M, BAR=256M
[    5.034104] [drm] RAM width 64bits DDR
[    5.034197] [TTM] Zone  kernel: Available graphics memory: 431040 kiB.
[    5.034201] [TTM] Zone highmem: Available graphics memory: 1679748 kiB.
[    5.034204] [TTM] Initializing pool allocator.
[    5.034235] [drm] radeon: 256M of VRAM memory ready
[    5.034239] [drm] radeon: 512M of GTT memory ready.
[    5.034266] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    5.034269] [drm] Driver supports precise vblank timestamp query.
[    5.034319] radeon 0000:01:00.0: irq 45 for MSI/MSI-X
[    5.034328] radeon 0000:01:00.0: radeon: using MSI.
[    5.034365] [drm] radeon: irq initialized.
[    5.034371] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    5.035619] [drm] Loading RV610 Microcode
[    5.036364] input: Dell Premium USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input3
[    5.036543] generic-usb 0003:413C:3016.0001: input,hidraw0: USB HID v1.11 Mouse [Dell Premium USB Optical Mouse] on usb-0000:00:1d.0-2/input0
[    5.050615] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input4
[    5.050837] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1/input0
[    5.074114] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input5
[    5.074240] generic-usb 0003:045E:00DD.0003: input,hidraw2: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1/input1
[    5.076033] usbcore: registered new interface driver usbhid
[    5.076050] usbhid: USB HID core driver
[    5.154692] hda_codec: ALC882: BIOS auto-probing.
[    5.155436] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
[    5.159993] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[    5.171085] radeon 0000:01:00.0: WB enabled
[    5.202776] [drm] ring test succeeded in 0 usecs
[    5.202982] [drm] radeon: ib pool ready.
[    5.203076] [drm] ib test succeeded in 0 usecs
[    5.203084] failed to evaluate ATIF got AE_BAD_PARAMETER
[    5.204330] [drm] Radeon Display Connectors
[    5.204333] [drm] Connector 0:
[    5.204335] [drm]   VGA
[    5.204339] [drm]   DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
[    5.204341] [drm]   Encoders:
[    5.204344] [drm]     CRT2: INTERNAL_KLDSCP_DAC2
[    5.204347] [drm] Connector 1:
[    5.204349] [drm]   DIN
[    5.204351] [drm]   Encoders:
[    5.204353] [drm]     TV1: INTERNAL_KLDSCP_DAC2
[    5.204355] [drm] Connector 2:
[    5.204357] [drm]   DVI-I
[    5.204359] [drm]   HPD1
[    5.204362] [drm]   DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[    5.204364] [drm]   Encoders:
[    5.204366] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    5.204369] [drm]     DFP1: INTERNAL_LVTM1
[    5.262196] [drm] Radeon display connector VGA-1: Found valid EDID
[    5.272288] [drm] Radeon display connector DVI-I-1: No monitor connected or invalid EDID
[    5.272300] [drm] Internal thermal controller with fan control
[    5.272421] [drm] radeon: power management initialized
[    5.362067] [drm] fb mappable at 0xD0141000
[    5.362071] [drm] vram apper at 0xD0000000
[    5.362073] [drm] size 3145728
[    5.362076] [drm] fb depth is 24
[    5.362078] [drm]    pitch is 4096
[    5.362243] fbcon: radeondrmfb (fb0) is primary device
[    5.460145] firewire_core: created device fw0: GUID 00016c2000213c01, S400
[    5.773445] Console: switching to colour frame buffer device 128x48
[    5.777224] fb0: radeondrmfb frame buffer device
[    5.777227] drm: registered panic notifier
[    5.777235] [drm] Initialized radeon 2.10.0 20080528 for 0000:01:00.0 on minor 0
[    5.777328] HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    5.777424] HDA Intel 0000:01:00.1: irq 46 for MSI/MSI-X
[    5.777455] HDA Intel 0000:01:00.1: setting latency timer to 64
[    5.784042] scsi 6:0:0:0: Direct-Access     HP       Photosmart C4600 1.00 PQ: 0 ANSI: 5
[    5.786780] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[    5.801865] HDMI status: Pin=3 Presence_Detect=0 ELD_Valid=0
[    5.802225] input: HDA ATI HDMI HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input8
[    6.487127] EXT4-fs (sda3): re-mounted. Opts: (null)
[    6.785006] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[    6.888121] Adding 1052252k swap on /dev/sda2.  Priority:-1 extents:1 across:1052252k 
[    8.074235] sky2 0000:02:00.0: eth0: enabling interface
[    9.794342] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control both
[   23.521782] EXT4-fs (sda3): re-mounted. Opts: commit=0
[   23.693737] EXT4-fs (sda4): re-mounted. Opts: commit=0
[ 1436.750002] fuse init (API version 7.16)
[ 1437.864470] NET: Registered protocol family 10
[ 1448.683202] eth0: no IPv6 routers present

Triston J. Taylor · 2012-02-08 21:33:25

udev + udisk are the managers hal is not in use dbus is daemonized that's pretty much all I know.

Gusar · 2012-02-08 21:42:15

I just checked, I don't get anything either in dmesg when I insert a DVD. It's detected anyway, but I use HAL. So now I have no idea whether your issue is in the drive or in udisks.

But there's this. Run "udevadm monitor". After inserting a DVD, I get this:

KERNEL[1210107.118190] change   /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/host41/target41:0:0/41:0:0:0/block/sr0 (block)
UDEV  [1210107.704385] change   /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/host41/target41:0:0/41:0:0:0/block/sr0 (block)
KERNEL[1210123.009274] change   /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/host41/target41:0:0/41:0:0:0/block/sr0 (block)
UDEV  [1210127.486872] change   /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/host41/target41:0:0/41:0:0:0/block/sr0 (block)

So udev sees a disc being inserted. If you get something similar, the issue is then probably in udisks.

Last edited by Gusar (2012-02-08 21:43:59)

Triston J. Taylor · 2012-02-08 21:47:58

Which package is the udevadm command belong to? I get the command not found error for udevadm and udevinfo. Pacman says udev is installed and up to date.

Triston J. Taylor · 2012-02-08 21:50:25

Oh, sorry found it in /sbin/

KERNEL[56949.004945] change   /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0/block/sr0 (block)
UDEV  [56949.254089] change   /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0/block/sr0 (block)

Triston J. Taylor · 2012-02-08 21:59:18

Should I be running the udisks daemon (udisksd)? I checked the archwiki but the udisks page is a sub-article for udev and does not at all mention that there is a udisks daemon.

http://www.freedesktop.org/wiki/Software/udisks

udisks
The udisks project provides:
a daemon, udisksd, that implements well-defined D-Bus interfaces that can be used to query and manipulate storage devices.
a command-line tool, udisksctl, that can be used to query and use the daemon
The actions that a user can perform using udisks are restricted using polkit.

Gusar · 2012-02-08 22:09:18

The udisks daemon is usually started automatically by whatever app is using it (Nautilus, Thunar, etc). What mounts your CDs? DVDs should work the same way.

defears · 2012-02-08 22:11:22

https://wiki.archlinux.org/index.php/Ud … ve_support

Triston J. Taylor · 2012-02-08 22:33:31

Well, /dev/sr0 belongs to the root group and is owned by root but root cannot even detect the dvd and, CDs work in the user space under this configuration so I will just have to chalk this up to a second faulty drive and grab the last one off of the shelf.

The first drive I tried was working fine on a ubuntu machine last week, the second drive I tried was working fine on a dual boot XP/Fedora machine a few years back. I find it hard to believe that sitting on a shelf or maybe being slightly bumped around disables 'only' the DVD functionality of these drives, but I tell ya what, it sure as hell would not surprise me if the devices were made to 'fail-on-condition' by the manufacturers. Eversince the DRM revolution, quality hardware is getting harder and harder to come by. I've seen DVD-ROM drives from '98 still in operation... this annoys me @ $30 a pop I might just have on my hands $90 worth of junk + shipping & handling.

fsckd · 2012-02-09 03:05:02

moderator comment: Split from here: https://bbs.archlinux.org/viewtopic.php?id=77274
Please do not necro-post: https://wiki.archlinux.org/index.php/Fo … Bumping.27

For what it's worth, my PATA CD and DVD drives appear as sr0 and sr1 respectively. Can you manually mount?

Arch Linux

#1 2012-02-08 21:10:03

IDE DVD drive problem

#2 2012-02-08 21:16:09

Re: IDE DVD drive problem

#3 2012-02-08 21:31:01

Re: IDE DVD drive problem

#4 2012-02-08 21:33:25

Re: IDE DVD drive problem

#5 2012-02-08 21:42:15

Re: IDE DVD drive problem

#6 2012-02-08 21:47:58

Re: IDE DVD drive problem

#7 2012-02-08 21:50:25

Re: IDE DVD drive problem

#8 2012-02-08 21:59:18

Re: IDE DVD drive problem

#9 2012-02-08 22:09:18

Re: IDE DVD drive problem

#10 2012-02-08 22:11:22

Re: IDE DVD drive problem

#11 2012-02-08 22:33:31

Re: IDE DVD drive problem

#12 2012-02-09 03:05:02

Re: IDE DVD drive problem

Board footer