You are not logged in.
Pages: 1
Topic closed
Hi!
I just installed arch (from network).
Everything went fine and (wired) network was set up by configure script and worked flawlessly.
After rebooting no network whatsoever.
ping static addresses: no network
ifconfig missing
ip addr shows: eth1 down
/etc/pacman.d/gnupg/gpg.conf disappeared
I'm quite upset about it.
I fixed the net:
# ip addr add 192.168.0.2/24 dev eth1
# ip route add default via 192.168.0.254
I'm very curious what possibly went wrong?
What are the steps to fix this permanently?
EDIT: went through the manual pages on setting up network,
/etc/network.d is missing
Last edited by iram (2012-02-11 15:13:36)
Offline
ifconfig missing
http://www.archlinux.org/news/deprecation-of-net-tools/
/etc/network.d is missing
It's not possible that some package was there before reboot and just disappeared: https://wiki.archlinux.org/index.php/FA … is_X_in.3F
Last edited by karol (2012-02-11 15:20:34)
Offline
/etc/network.d is provided by netcfg.
Do you have a dhcp server on the network? If you do, why not use it?
Evil #archlinux@libera.chat channel op and general support dude.
. files on github, Screenshots, Random pics and the rest
Offline
I tried dhclient, it wasn't there. Didn't think of dhcpcd
/etc/network.d is provided by netcfg.
Do you have a dhcp server on the network? If you do, why not use it?
Offline
i just did a net install from archlinux-2011.08.19-netinstall-x86_64.iso and have the same problem... during the install no problem establishing a network connection, but when i reboot after the install there is no network connection.
edit... i am using a wired connection, and set it up as dhcp during install.
Last edited by jayveesea (2012-02-26 02:25:12)
Offline
Start with taking a look at the steps defined here.
Burninate!
Offline
i just did a net install from archlinux-2011.08.19-netinstall-x86_64.iso and have the same problem... during the install no problem establishing a network connection, but when i reboot after the install there is no network connection.
edit... i am using a wired connection, and set it up as dhcp during install.
just run dhcpcd eth0 then
Evil #archlinux@libera.chat channel op and general support dude.
. files on github, Screenshots, Random pics and the rest
Offline
ok, thanks for the replies and the help. i have tried running through troubleshooting section for network, and still do not have a working network connection.
here is what i have so far...
step1.
"lspci -v" tells me that my driver for my network card is "forcedeth"
"dmesg |grep forcedeth" returns this...
[ 4.523336] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 4.523491] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 4.523495] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 4.584392] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:25:22:34:22:ec
[ 4.584395] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim msi desc-v3
[ 6.625507] forcedeth 0000:00:0a.0: irq 41 for MSI/MSI-X
...this output seems a little different then what is given in the example.
i proceeded with step2 and step3 and it appeared as if i have an ip address, but when i test the connection with ping, i get no response.
i also tried adding...
dhcpcd -k eth0
dhcpcd -nd eth0
...to /etc/rc.local and rebooted, but still nothing.
Offline
Can you post the output of the following after you've run dhcpcd eth0?
# ip addr
# cat /etc/resolv.conf
# ping 8.8.8.8
# ping www.google.com
Burninate!
Offline
good news. after i booted up and issued "dhcpcd eth0" it said dhcpcd was already running. so i issued "ip addr" and it confirmed i had an ip address, and then i issued "ping -c3 8.8.8.8" and was able to get a response.
thanks for all the help! i am not sure what i did, but it is working now.
-j
Offline
I just did a fresh install using archlinux-2012.10.06-dual.iso and had the same problem. When I booted after the installation I had no network. To get the network working I first ran
# dhcpcd eth0
to manually enable networking. Then installed netcfg using
# pacman -S netcfg
After that I added the configuration so that eth0 uses dhcp by doing
# cd /etc/network.d
# ln -s examples/ethernet-dhcp .
Finally, enable this profile on boot
# systemctl enable netcfg@ethernet-dhcp.service
And the next time I rebooted I had a working internet connection.
Offline
Don't necrobump
systemctl enable dhcpcd@eth0.service
If not using eth0: https://bugs.archlinux.org/task=31093
Evil #archlinux@libera.chat channel op and general support dude.
. files on github, Screenshots, Random pics and the rest
Offline
Try these steps.
# first find the name of n/w adapters
ip addr
# next turn it up
sudo dhcpcd ethx
# enable dhcpcd so you donot have to do it every time you reboot
sudo systemctl enable dhcpcd@ethx.service
NOTE: replace ethx with whatever you found in first command
Offline
Please reread the post above yours, notably the injunction not to necrobump: https://wiki.archlinux.org/index.php/Fo … bumping.22
Closing
Offline
Pages: 1
Topic closed