You are not logged in.

#1 2012-04-09 17:33:02

goodboy
Member
Registered: 2007-02-23
Posts: 34

Setting up qingy fluxbox and conselkit

I'm probably to dumb to figure out how to avoid the inactive session problem on fluxbox (see below)

Using qingy (1.0) this is how I start fluxbox

exec ck-launch-session dbus-launch --sh-syntax --exit-with-session startfluxbox

In my understanding ths all it takes for an active session

yet ck-list-sessions still gives

Session1:
    unix-user = '1000'
    realname = '(null)'
    seat = 'Seat2'
    session-type = ''
    active = FALSE
    x11-display = ':1'
    x11-display-device = '/dev/tty3'
    display-device = '/dev/tty1'
    remote-host-name = ''
    is-local = FALSE
    on-since = '2012-04-09T16:49:18.486520Z'
    login-session-id = ''


For completeness' sake here is also
/etc/pam.d/qingy


auth      required   pam_tally2.so onerr=succeed
auth      required   pam_shells.so
auth      required   pam_nologin.so
auth      include    system-auth

account      required   pam_access.so
account      required   pam_nologin.so
account      include   system-auth
account      required   pam_tally2.so onerr=succeed

password     include    system-auth

session      optional   pam_loginuid.so   #   comes before the pam_ck_connector
session      required   pam_env.so
session      optional   pam_lastlog.so
session      include    system-auth
session      optional   pam_ck_connector.so
session      optional   pam_motd.so motd=/etc/motd
session      optional   pam_mail.so




I should add that both consolekit and plokit are installed and running

Last edited by goodboy (2012-04-09 17:44:01)

Offline

#2 2012-04-09 22:08:29

goodboy
Member
Registered: 2007-02-23
Posts: 34

Re: Setting up qingy fluxbox and conselkit

Well just in the likelyhood someone else stumbles over this thread. After much searching and reading  I conclude Qingy as for now isnt woth trying. Not as long as you need proper console-kit support. Some applications for instance need a working keyring manager which itself relies on an active console-kit session.  Other than that I really liked qingy. I'm now back to the good old startx resulting in an active session and a working gnome keyring.

Last edited by goodboy (2012-04-09 22:09:41)

Offline

#3 2012-04-10 02:03:58

sonoran
Member
From: sonoran desert
Registered: 2009-01-12
Posts: 192

Re: Setting up qingy fluxbox and conselkit

goodboy wrote:

After much searching and reading  I conclude Qingy as for now isnt woth trying. Not as long as you need proper console-kit support.

I use qingy with console-kit and openbox without any problems. Have you worked around the locked tty issue by putting

openvt -c 63 -f -- console-kit-daemon --no-daemon &

in rc.local? It's at the bottom of the wiki page for qingy.

Offline

#4 2012-04-11 15:03:25

goodboy
Member
Registered: 2007-02-23
Posts: 34

Re: Setting up qingy fluxbox and conselkit

sonoran wrote:
goodboy wrote:

After much searching and reading  I conclude Qingy as for now isnt woth trying. Not as long as you need proper console-kit support.

I use qingy with console-kit and openbox without any problems. Have you worked around the locked tty issue by putting

openvt -c 63 -f -- console-kit-daemon --no-daemon &

in rc.local? It's at the bottom of the wiki page for qingy.

Yes I tried that too.

Lately after working smoothly for like 5 yrs. there was yet another annoyance. If there is no activity qingy's login screen will simple black out. It resumes after you start typing (or move the mouse pointer) but  disappears immediately as soon you stop. The menu had its own issues too. Well, anyway fluxbox, mingetty + autologin work perfectly now. I ditched qingy for good.

Offline

Board footer

Powered by FluxBB