Arch Linux

falconindy

Developer

From: New York, USA

Registered: 2009-10-22

Posts: 4,111

Website

Re: Kernel Panic strikes again ( VFS : Unable to mount root fs )

Looking back at your lsinitcpio output, you're still creating an image for the arch kernel. Not your own. You need to make a preset or explicitly specify the kernel in mkinitcpio's params.

---

blog | ±github

Surry

Member

Registered: 2012-01-11

Posts: 8

Re: Kernel Panic strikes again ( VFS : Unable to mount root fs )

Hello,

Here is my mkinit.conf

# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run.  Advanced users may wish to specify all system modules
# in this array.  For instance:
#     MODULES="piix ide_disk reiserfs"
MODULES="radeon"

# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image.  This is run first, so it may be used to
# override the actual binaries used in a given hook.
# (Existing files are NOT overwritten if already added)
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way.  This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options
# like so:
#    FILES="/etc/modprobe.d/modprobe.conf"
FILES=""

# HOOKS
# This is the most important setting in this file.  The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
##   This setup specifies all modules in the MODULES setting above.
##   No raid, lvm2, or encrypted root is needed.
#    HOOKS="base"
#
##   This setup will autodetect all modules for your system and should
##   work as a sane default
#    HOOKS="base udev autodetect pata scsi sata filesystems"
#
##   This is identical to the above, except the old ide subsystem is
##   used for IDE devices instead of the new pata subsystem.
#    HOOKS="base udev autodetect ide scsi sata filesystems"
#
##   This setup will generate a 'full' image which supports most systems.
##   No autodetection is done.
#    HOOKS="base udev pata scsi sata usb filesystems"
#
##   This setup assembles a pata mdadm array with an encrypted root FS.
##   Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
#    HOOKS="base udev pata mdadm encrypt filesystems"
#
##   This setup loads an lvm2 volume group on a usb device.
#    HOOKS="base udev usb lvm2 filesystems"
#
##   NOTE: If you have /usr on a separate partition, you MUST include the
#    fsck and shutdown hooks.
HOOKS="base udev autodetect pata scsi sata filesystems usbinput fsck"

# COMPRESSION
# Use this to compress the initramfs image. With kernels earlier than
# 2.6.30, only gzip is supported, which is also the default. Newer kernels
# support gzip, bzip2 and lzma. Kernels 2.6.38 and later support xz
# compression.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"

# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""

You can try placing ext4 in your modules array, no idea if that will work though.