You are not logged in.
So I've been using catalyst for a while on my HD5750 and overall enjoyed it but got fed up with how it wouldn't keep up with xserver and the kernel, so in April I decided to go for the open source drivers. Those drivers performed fine for what I wanted but they lacked features I use, so yesterday I decided to go back to the catalyst drivers.
I'm using KDE 4.8 and the catalyst-test package from AUR. The problem is anything opengl related will show 1 frame and completely freeze, whether that be kwin, glxgears, a web browser, or a game.
amdcccle and glxinfo seem to give accurate info stating that everything is working (such as direct rendering, opengl 4.2, and so on).
I have noticed that if I disable vsync and tear-free, opengl programs will still only draw 1 frame, but they won't freeze. So for example I can run GLX gears and it might show a frame or 2 but I'm still getting reports of framerate in the terminal. If I disable "Catalyst AI" as well, then the programs will ONLY update their display if something else (aside from the mouse) is visually changing the screen. So if I drag a window around, glxgears will have a smooth consistent framerate but if I stop dragging it, the gears stop moving (but I'm still getting outputs).
Any idea why this is happening and what I can do about it?
Last edited by schmidtbag (2012-07-02 19:56:46)
Offline
So I've narrowed down the problem to being either fglrx's fault or KDE 4.8. I had both update at the same time so I can't really tell. The reasoning why I'm blaming fglrx should be fairly obvious.
I think KDE might be the problem because if I create a brand new user account and log into it, it works just fine with anything opengl related. However, if I reboot there seems to be something that gets triggered and screws up opengl again. I can't figure out what this is - I don't change a single option in this other user account. The weird thing is it isn't easily reproducible, so for example I might clean the slate of that new user account and reboot several times with success each time, but then one time it doesn't work anymore and when that happens, opengl never works again.
I tried deleting nearly everything KDE related on my account and I was able to get opengl working for 1 session. After re-applying all my settings (which, BTW, were all working just fine and were active in front of me) and rebooting, opengl failed again. I don't feel like deleting my account every time I log in, so unless someone can help me out or the next catalyst and/or kde release arrives, I'm going back to the open source drivers.
Offline
Do you watch the GPU temperature when you're running the open source driver? My HD6770 runs much hotter (15-20C higher) when running it as opposed to fglrx. I don't know if it is dangerously hot, but I avoid the open source driver for this reason.
Tim
Last edited by ratcheer (2012-07-04 12:47:08)
Offline
Yes, I do. I would REALLY like to watch GPU and VRAM usage too but I don't know how to do that with the open source drivers. Anyways, 15-20C higher isn't an exact temperature so I can't tell if its dangerously hot. If your GPU reaches 60C while idle, you likely have a ventilation problem. The 6770 with an appropriate heatsink should struggle to get past 65 while under chronic full load in a well ventilated case.
I assume your temperatures get so much higher is because the open source drivers aren't as good at power saving. The arch wiki does go into a little bit of depth about this if you need it tho.
Offline
My card runs at 42-50C with fglrx and 64-68C with the open source radeon driver. It is enough of a difference that I avoid running Siduction Linux, where I have been unable to successfully install fglrx. When I reboot from Siduction to one of my other installations that do run fglrx, I can then watch the temperature gradually go down from 64C to, say, 44C. It is a real difference and I am comparing apples to apples.
Tim
Last edited by ratcheer (2012-07-04 21:40:02)
Offline
Again, is this under load or idle? Either way, you probably have something screwing with the ventillation. My room as of right now is maybe 85F, I'm using a slightly overclocked 5750 (the 57xx and 67xx series cards are architecturally identical) and its running at 51C right now. Considering my GPU is slightly worse than yours and I'm likely in a much hotter situation right now, you should not be getting temperatures anywhere near 60C at idle with the open source drivers.
Offline
With the open source driver, it runs at about 64C with no load and 67-68 with a load. It only gets up to around 50C under a full load with fglrx, and goes as low as 42 with no load.
Maybe there is some ventilation issue, but it gets much hotter with the open source driver. The room stays fairly cool and my PC is in a Coolermaster tower case with plenty of venting at the front and top.
Tim
Offline
Your idle temps for catalyst are pretty reasonable. They could be better, but they're not bad. Just check the ati page in the arch wiki and look for the power saving section. Also I'm sure there's a few xorg.conf changes you can make to improve it.
Offline
Have you tried setting the environment variable vblank_mode=0 or vblank_mode=1 before running a GL app?
6EA3 F3F3 B908 2632 A9CB E931 D53A 0445 B47A 0DAB
Great things come in tar.xz packages.
Offline
Thank you, schmidtbag and ConnorBehan
Tim
Offline
Hi! I am experiencing almost the same problem with glxgears, also I can not enable rendering via OpenGL and some effects looks less smooth then on opensource driver. But in case of open source power saving wont work for my card and sensors shows 60 degrees at idle, now (with cataclyst) temperature drops to 34.
schmidtbag, did you solved the problem in your case?
P.S. AMD Radeon HD 7800 Series
Offline
Hi! I am experiencing almost the same problem with glxgears, also I can not enable rendering via OpenGL and some effects looks less smooth then on opensource driver. But in case of open source power saving wont work for my card and sensors shows 60 degrees at idle, now (with cataclyst) temperature drops to 34.
schmidtbag, did you solved the problem in your case?
P.S. AMD Radeon HD 7800 Series
no sorry I didn't. but, I heard that there's the latest version of kde supports better supports the catalyst drivers so maybe you can get more luck out of that.
Offline
For anyone interested: in my case removing kwinrc and apps/kwin/ solves the problem (after relogin I have OpenGL and rasted enabled by default, also, glxgears works well).
Offline