You are not logged in.
My USB flash drives are no longer showing up in /dev. I also don't see them in /dev/disks/... either. Dmesg outputs:
[731969.826862] usb 1-1: new high-speed USB device number 5 using ehci_hcdAny ideas on where to start?
Last edited by nadman10 (2012-09-26 22:12:22)
Offline
Corrupt mbr or gpt? Maybe see if fdisk/gdisk/parted recognizes it.
Offline
It happens with all USB drives, so I doubt that. None of those programs see it without the block device showing up.
Offline
ls -l outputs:
Bus 001 Device 005: ID 0781:5530 SanDisk Corp. Cruzer
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5530 Cruzer
bcdDevice 1.00
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Bus 002 Device 002: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x045e Microsoft Corp.
idProduct 0x0040 Wheel Mouse Optical
bcdDevice 3.00
iManufacturer 1
iProduct 3
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 72
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 3.05
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.05
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255Offline
Well, it is not a bad start...
[35839.389912] usb 7-1: new high-speed USB device number 3 using ehci_hcd
[35840.135132] usbcore: registered new interface driver uas
[35840.140873] Initializing USB Mass Storage driver...
[35840.141043] scsi6 : usb-storage 7-1:1.0
[35840.141150] usbcore: registered new interface driver usb-storage
[35840.141151] USB Mass Storage support registered.
[35841.144825] scsi 6:0:0:0: Direct-Access USB Flash Disk 1100 PQ: 0 ANSI: 0 CCS
[35841.149681] sd 6:0:0:0: [sdb] 1957888 512-byte logical blocks: (1.00 GB/956 MiB)
[35841.150680] sd 6:0:0:0: [sdb] Write Protect is off
[35841.150687] sd 6:0:0:0: [sdb] Mode Sense: 43 00 00 00
[35841.152148] sd 6:0:0:0: [sdb] No Caching mode page present
[35841.152156] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[35841.155055] sd 6:0:0:0: [sdb] No Caching mode page present
[35841.155062] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[35841.156065] sdb: sdb1
[35841.158174] sd 6:0:0:0: [sdb] No Caching mode page present
[35841.158180] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[35841.158184] sd 6:0:0:0: [sdb] Attached SCSI disk
ewaller@odin:~ 1002 %lsmod | grep usb
usb_storage 44760 0
scsi_mod 133152 5 uas,usb_storage,libata,sd_mod,sr_mod
usbcore 147434 5 uas,uhci_hcd,uvcvideo,usb_storage,ehci_hcd
usb_common 954 1 usbcore
ewaller@odin:~ 1003 %...but -- Look at the kernel modules you have loaded (lsmod) There should be a couple dozen modules, including usbcore and usb_storage. How do yours look?
(BTW, I am very close to calling it a night)
Nothing is too wonderful to be true, if it be consistent with the laws of nature -- Michael Faraday
The shortest way to ruin a country is to give power to demagogues.— Dionysius of Halicarnassus
---
How to Ask Questions the Smart Way
Offline
lsmod outputs:
Module Size Used by
fuse 60222 2
snd_hda_codec_hdmi 21248 1
snd_hda_codec_realtek 50748 1
snd_hda_intel 21808 4
snd_hda_codec 83164 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel
snd_pcm 61301 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_page_alloc 5901 2 snd_pcm,snd_hda_intel
powernow_k8 12012 1
snd_hwdep 4746 1 snd_hda_codec
snd_timer 14902 1 snd_pcm
snd 44906 15 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec,snd_hda_intel
soundcore 4378 1 snd
mperf 1023 1 powernow_k8
forcedeth 50565 0
i2c_nforce2 4456 0
k8temp 2590 0
kvm_amd 46302 0
kvm 315149 1 kvm_amd
ppdev 4750 0
parport_pc 26569 0
evdev 7662 4
processor 24235 1 powernow_k8
fan 1902 0
parport 26063 2 ppdev,parport_pc
pcspkr 1455 0
thermal 6563 0
button 3614 0
vboxdrv 195748 0
ext4 398870 3
crc16 1091 1 ext4
jbd2 66342 1 ext4
mbcache 4345 1 ext4
hid_generic 709 0
sd_mod 26991 5
usbhid 32107 0
pata_amd 8155 0
hid 67908 2 hid_generic,usbhid
pata_acpi 2388 0
ohci_hcd 19024 0
ata_generic 2423 0
sata_nv 17444 4
libata 146119 4 pata_acpi,sata_nv,pata_amd,ata_generic
ehci_hcd 35958 0
scsi_mod 112591 2 libata,sd_mod
usbcore 123890 3 ohci_hcd,ehci_hcd,usbhid
usb_common 622 1 usbcore
floppy 48646 0
radeon 782747 2
i2c_algo_bit 4615 1 radeon
drm_kms_helper 29069 1 radeon
ttm 46603 1 radeon
drm 182234 4 ttm,drm_kms_helper,radeon
agpgart 21935 2 drm,ttm
i2c_core 16720 5 drm,drm_kms_helper,i2c_algo_bit,radeon,i2c_nforce2So, I do see usbcore, but not usb_storage. I tried to manually load usb_storage using:
modprobe usb_storageBut had no luck.
Offline
Forgive me if this is too simple - but I've been guilty of it a number of times myself: have you rebooted since your last kernel upgrade?
This is the expected outcome if the kernel that is actively running does not match what is installed on disk.
"UNIX is simple and coherent" - Dennis Ritchie; "GNU's Not Unix" - Richard Stallman
Offline
Forgive me if this is too simple - but I've been guilty of it a number of times myself: have you rebooted since your last kernel upgrade?
This is the expected outcome if the kernel that is actively running does not match what is installed on disk.
Two giant dumb dumb mistakes in one week.... I'm on a roll here. Thanks guys for your help.
Offline
Forgive me if this is too simple - but I've been guilty of it a number of times myself: have you rebooted since your last kernel upgrade?
This is the expected outcome if the kernel that is actively running does not match what is installed on disk.
Damn, I wondered why I could only connect my USB drives after a reboot. It seems like kernel releases happen more often than me plugging in an USB stick.
Thanks for that.
Offline