You are not logged in.

#1 2012-09-25 16:46:59

hdhiman
Member
Registered: 2009-09-05
Posts: 52

Cannot boot to X (kdm) unless reboot.

Dear all,
I'm using the ATI Catalyst driver, the open source ATI driver doesn't support my card yet (HD 7850).
The issue is, the first time i boot the sytem, it always goes to tty1.
Only after a reboot I can boot to X.

I followed the instructions to have kdm allowed at init level 5 inside /etc/inittab: https://wiki.archlinux.org/index.php/Display_Manager

Using the option to default to tty7, i see a blinking cursor. If I reboot, I see kdm.

I'm guessing its got something to do with the standby signal to the PC, because this happens only after I switch off the main supply. As long as the motherboard has the standby voltage, it'll boot to kdm.

Any help would be appreciated.

Last edited by hdhiman (2012-09-25 16:48:37)

Offline

#2 2012-09-25 17:27:23

DSpider
Member
From: Romania
Registered: 2009-08-23
Posts: 2,273

Re: Cannot boot to X (kdm) unless reboot.

Try another login manager. And try without one at all (runlevel 3, where you need to type "startx").


"How to Succeed with Linux"

I have made a personal commitment not to reply in topics that start with a lowercase letter. Proper grammar and punctuation is a sign of respect, and if you do not show any, you will NOT receive any help (at least not from me).

Offline

#3 2012-09-26 01:03:31

hdhiman
Member
Registered: 2009-09-05
Posts: 52

Re: Cannot boot to X (kdm) unless reboot.

Thanks for the reply. I'll try out something else and revert back.

Offline

#4 2012-09-26 16:48:44

hdhiman
Member
Registered: 2009-09-05
Posts: 52

Re: Cannot boot to X (kdm) unless reboot.

Hey, I tried without X, startx doesn't work.
It seems the problem is in the starting of X, the first time there's no display detected:

fglrx: No matching Device section for instance (BusID PCI:0@6:0:1) found

Offline

#5 2012-09-26 20:11:34

12eason
Banned
Registered: 2010-07-20
Posts: 103

Re: Cannot boot to X (kdm) unless reboot.

Did you run `aticonfig --initial`?

Offline

#6 2012-09-27 01:28:07

hdhiman
Member
Registered: 2009-09-05
Posts: 52

Re: Cannot boot to X (kdm) unless reboot.

12eason wrote:

Did you run `aticonfig --initial`?

Yeah, I did run 'aticonfig' , but I'm not sure about the '--initial'.
Anyways, Xorg.conf exists, as created by the config tool. I'm not on my home pc right now, but I'll post the config once I'm back.


This error (in previous post) only comes up on the first boot. After that its fine.
I'll also recheck my rc.conf.

Offline

#7 2012-09-27 14:25:16

hdhiman
Member
Registered: 2009-09-05
Posts: 52

Re: Cannot boot to X (kdm) unless reboot.

Here's the Xorg.0.log just after turning the PC on:

[     2.226] 
X.Org X Server 1.12.4
Release Date: 2012-08-27
[     2.226] X Protocol Version 11, Revision 0
[     2.226] Build Operating System: Linux 3.4.8-1-ARCH x86_64 
[     2.226] Current Operating System: Linux dmanPC 3.5.3-1-ARCH #1 SMP PREEMPT Sun Aug 26 09:14:51 CEST 2012 x86_64
[     2.226] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=3766a71b-dbfe-4cc2-b7bd-948878b5da67 ro nomodeset quiet
[     2.226] Build Date: 27 August 2012  08:04:39AM
[     2.226]  
[     2.226] Current version of pixman: 0.26.2
[     2.226] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[     2.226] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     2.226] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Sep 28 05:57:41 2012
[     2.227] (==) Using config file: "/etc/X11/xorg.conf"
[     2.228] (==) Using config directory: "/etc/X11/xorg.conf.d"
[     2.228] (==) ServerLayout "aticonfig Layout"
[     2.228] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
[     2.228] (**) |   |-->Monitor "aticonfig-Monitor[0]-0"
[     2.229] (**) |   |-->Device "aticonfig-Device[0]-0"
[     2.229] (==) Automatically adding devices
[     2.229] (==) Automatically enabling devices
[     2.231] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[     2.231] 	Entry deleted from font path.
[     2.231] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[     2.231] 	Entry deleted from font path.
[     2.231] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[     2.231] 	Entry deleted from font path.
[     2.231] 	(Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[     2.232] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[     2.232] 	Entry deleted from font path.
[     2.232] 	(Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[     2.232] (==) FontPath set to:
	/usr/share/fonts/misc/,
	/usr/share/fonts/TTF/
[     2.232] (==) ModulePath set to "/usr/lib/xorg/modules"
[     2.232] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[     2.232] (II) Loader magic: 0x7c8b00
[     2.232] (II) Module ABI versions:
[     2.232] 	X.Org ANSI C Emulation: 0.4
[     2.232] 	X.Org Video Driver: 12.1
[     2.232] 	X.Org XInput driver : 16.0
[     2.232] 	X.Org Server Extension : 6.0
[     2.232] (--) PCI:*(0:7:0:0) 1002:6819:1462:2730 rev 0, Mem @ 0xe0000000/268435456, 0xf7b00000/262144, I/O @ 0x0000c000/256, BIOS @ 0x????????/131072
[     2.232] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[     2.232] (II) "extmod" will be loaded by default.
[     2.232] (II) "dbe" will be loaded by default.
[     2.232] (II) "glx" will be loaded by default.
[     2.232] (II) "record" will be loaded by default.
[     2.232] (II) "dri" will be loaded by default.
[     2.232] (II) "dri2" will be loaded by default.
[     2.232] (II) LoadModule: "extmod"
[     2.233] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[     2.233] (II) Module extmod: vendor="X.Org Foundation"
[     2.233] 	compiled for 1.12.4, module version = 1.0.0
[     2.233] 	Module class: X.Org Server Extension
[     2.233] 	ABI class: X.Org Server Extension, version 6.0
[     2.233] (II) Loading extension MIT-SCREEN-SAVER
[     2.233] (II) Loading extension XFree86-VidModeExtension
[     2.233] (II) Loading extension XFree86-DGA
[     2.233] (II) Loading extension DPMS
[     2.233] (II) Loading extension XVideo
[     2.233] (II) Loading extension XVideo-MotionCompensation
[     2.233] (II) Loading extension X-Resource
[     2.233] (II) LoadModule: "dbe"
[     2.233] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[     2.234] (II) Module dbe: vendor="X.Org Foundation"
[     2.234] 	compiled for 1.12.4, module version = 1.0.0
[     2.234] 	Module class: X.Org Server Extension
[     2.234] 	ABI class: X.Org Server Extension, version 6.0
[     2.234] (II) Loading extension DOUBLE-BUFFER
[     2.234] (II) LoadModule: "glx"
[     2.234] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[     2.236] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[     2.236] 	compiled for 6.9.0, module version = 1.0.0
[     2.236] (II) Loading extension GLX
[     2.236] (II) LoadModule: "record"
[     2.236] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[     2.237] (II) Module record: vendor="X.Org Foundation"
[     2.237] 	compiled for 1.12.4, module version = 1.13.0
[     2.237] 	Module class: X.Org Server Extension
[     2.237] 	ABI class: X.Org Server Extension, version 6.0
[     2.237] (II) Loading extension RECORD
[     2.237] (II) LoadModule: "dri"
[     2.237] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[     2.237] (II) Module dri: vendor="X.Org Foundation"
[     2.237] 	compiled for 1.12.4, module version = 1.0.0
[     2.237] 	ABI class: X.Org Server Extension, version 6.0
[     2.237] (II) Loading extension XFree86-DRI
[     2.237] (II) LoadModule: "dri2"
[     2.238] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[     2.238] (II) Module dri2: vendor="X.Org Foundation"
[     2.238] 	compiled for 1.12.4, module version = 1.2.0
[     2.238] 	ABI class: X.Org Server Extension, version 6.0
[     2.238] (II) Loading extension DRI2
[     2.238] (II) LoadModule: "fglrx"
[     2.238] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[     2.262] (II) Module fglrx: vendor="FireGL - AMD Technologies Inc."
[     2.262] 	compiled for 1.4.99.906, module version = 8.98.2
[     2.262] 	Module class: X.Org Video Driver
[     2.262] (II) Loading sub module "fglrxdrm"
[     2.262] (II) LoadModule: "fglrxdrm"
[     2.262] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[     2.263] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[     2.263] 	compiled for 1.4.99.906, module version = 8.98.2
[     2.263] (II) AMD Proprietary Linux Driver Version Identifier:8.98.2
[     2.263] (II) AMD Proprietary Linux Driver Release Identifier: 8.982                                
[     2.263] (II) AMD Proprietary Linux Driver Build Date: Jul 27 2012 20:37:56
[     2.263] (++) using VT number 8

[     2.264] (WW) Falling back to old probe method for fglrx
[     2.269] (II) Loading PCS database from /etc/ati/amdpcsdb
[     2.271] (WW) fglrx: No matching Device section for instance (BusID ) found
[     2.271] (EE) No devices detected.
[     2.271] 
Fatal server error:
[     2.271] no screens found
[     2.271] 
Please consult the The X.Org Foundation support 
	 at http://wiki.x.org
 for help. 
[     2.271] Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[     2.271] 

Here's the log during reboot, I've put the portion that differs from the first log:

[     2.289] (++) using VT number 8

[     2.290] (WW) Falling back to old probe method for fglrx
[     2.295] (II) Loading PCS database from /etc/ati/amdpcsdb
[     2.296] (--) Chipset Supported AMD Graphics Processor (0x6819) found
[     2.296] (WW) fglrx: No matching Device section for instance (BusID PCI:0@6:0:1) found
[     2.297] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[     2.297] (II) AMD Video driver is signed
[     2.297] (II) fglrx(0): pEnt->device->identifier=0x82b7a0
[     2.297] (II) fglrx(0): === [xdl_xs112_atiddxPreInit] === begin
[     2.297] (II) Loading sub module "vgahw"
[     2.297] (II) LoadModule: "vgahw"
[     2.298] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[     2.298] (II) Module vgahw: vendor="X.Org Foundation"
[     2.298] 	compiled for 1.12.4, module version = 0.1.0
[     2.298] 	ABI class: X.Org Video Driver, version 12.1
[     2.298] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
[     2.298] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[     2.298] (==) fglrx(0): Default visual is TrueColor
[     2.298] (**) fglrx(0): Option "OpenGLOverlay" "0"
[     2.298] (**) fglrx(0): Option "DPMS" "true"
[     2.298] (==) fglrx(0): RGB weight 888
[     2.298] (II) fglrx(0): Using 8 bits per RGB 
[     2.298] (==) fglrx(0): Buffer Tiling is ON
[     2.299] (II) Loading sub module "fglrxdrm"
[     2.299] (II) LoadModule: "fglrxdrm"
[     2.299] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[     2.299] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[     2.299] 	compiled for 1.4.99.906, module version = 8.98.2
[     2.299] ukiDynamicMajor: found major device number 251
[     2.299] ukiDynamicMajor: found major device number 251
[     2.299] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[     2.299] ukiOpenDevice: node name is /dev/ati/card0
[     2.299] ukiOpenDevice: open result is 11, (OK)
[     2.299] ukiOpenByBusid: ukiOpenMinor returns 11
[     2.299] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[     2.299] (**) fglrx(0): NoAccel = NO
[     2.299] (**) fglrx(0): AMD 2D Acceleration Architecture enabled
[     2.299] (--) fglrx(0): Chipset: "AMD Radeon HD 7800 Series " (Chipset = 0x6819)
[     2.299] (--) fglrx(0): (PciSubVendor = 0x1462, PciSubDevice = 0x2730)
[     2.299] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original AMD
[     2.299] (--) fglrx(0): Linear framebuffer (phys) at 0xe0000000
[     2.299] (--) fglrx(0): MMIO registers at 0xf7c00000
[     2.299] (--) fglrx(0): I/O port at 0x0000c000
[     2.299] (==) fglrx(0): ROM-BIOS at 0x000c0000
[     2.300] (II) fglrx(0): AC Adapter is used
[     2.303] (II) fglrx(0): Primary V_BIOS segment is: 0xc000
[     2.303] (II) Loading sub module "vbe"
[     2.303] (II) LoadModule: "vbe"
[     2.303] (II) Loading /usr/lib/xorg/modules/libvbe.so
[     2.304] (II) Module vbe: vendor="X.Org Foundation"
[     2.304] 	compiled for 1.12.4, module version = 1.1.0
[     2.304] 	ABI class: X.Org Video Driver, version 12.1
[     2.304] (II) fglrx(0): VESA BIOS detected
[     2.304] (II) fglrx(0): VESA VBE Version 3.0
[     2.304] (II) fglrx(0): VESA VBE Total Mem: 16384 kB
[     2.304] (II) fglrx(0): VESA VBE OEM: AMD ATOMBIOS
[     2.304] (II) fglrx(0): VESA VBE OEM Software Rev: 15.17
[     2.304] (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2010, Advanced Micro Devices, Inc.
[     2.304] (II) fglrx(0): VESA VBE OEM Product: PITCAIRN
[     2.304] (II) fglrx(0): VESA VBE OEM Product Rev: 01.00
[     2.309] (II) fglrx(0): AMD Video BIOS revision 9 or later detected
[     2.309] (--) fglrx(0): Video RAM: 2097152 kByte, Type: GDDR5
[     2.309] (II) fglrx(0): PCIE card detected
[     2.309] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
[     2.309] (WW) fglrx(0): board is an unknown third party board, chipset is supported
[     2.311] (II) fglrx(0): Using adapter: 6:0.0.
[     2.320] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf400000000, MCFBSize = 0x80000000)
[     2.458] (II) fglrx(0): Interrupt handler installed at IRQ 48.
[     2.458] (II) fglrx(0): RandR 1.2 support is enabled!
[     2.458] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[     2.458] (==) fglrx(0): Center Mode is disabled 
[     2.458] (II) Loading sub module "fb"
[     2.458] (II) LoadModule: "fb"
[     2.458] (II) Loading /usr/lib/xorg/modules/libfb.so
[     2.461] (II) Module fb: vendor="X.Org Foundation"
[     2.461] 	compiled for 1.12.4, module version = 1.0.0
[     2.461] 	ABI class: X.Org ANSI C Emulation, version 0.4
[     2.461] (II) Loading sub module "ddc"
[     2.461] (II) LoadModule: "ddc"
[     2.461] (II) Module "ddc" already built-in
[     2.571] (II) fglrx(0): Finished Initialize PPLIB!
[     2.577] (II) fglrx(0): Output DFP1 using monitor section aticonfig-Monitor[0]-0
[     2.577] (II) fglrx(0): Output DFP2 has no monitor section
[     2.577] (II) fglrx(0): Output DFP3 has no monitor section
[     2.577] (II) fglrx(0): Output DFP4 has no monitor section
[     2.577] (II) fglrx(0): Output DFP5 has no monitor section
[     2.577] (II) fglrx(0): Output DFP6 has no monitor section
[     2.577] (II) fglrx(0): Output DFP7 has no monitor section
[     2.577] (II) fglrx(0): Output DFP8 has no monitor section
[     2.577] (II) fglrx(0): Output DFP9 has no monitor section
[     2.577] (II) fglrx(0): Output DFP10 has no monitor section
[     2.577] (II) fglrx(0): Output CRT1 has no monitor section
[     2.578] (II) Loading sub module "ddc"
[     2.578] (II) LoadModule: "ddc"
[     2.578] (II) Module "ddc" already built-in
[     2.578] (II) fglrx(0): Connected Display0: DFP10
[     2.578] (II) fglrx(0): Display0 EDID data ---------------------------
[     2.578] (II) fglrx(0): Manufacturer: SAM  Model: 524  Serial#: 1280455218
[     2.578] (II) fglrx(0): Year: 2009  Week: 20
[     2.578] (II) fglrx(0): EDID Version: 1.3
[     2.578] (II) fglrx(0): Digital Display Input
[     2.578] (II) fglrx(0): Max Image Size [cm]: horiz.: 48  vert.: 27
[     2.578] (II) fglrx(0): Gamma: 2.20
[     2.578] (II) fglrx(0): DPMS capabilities: Off
[     2.578] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[     2.578] (II) fglrx(0): First detailed timing is preferred mode
[     2.578] (II) fglrx(0): redX: 0.648 redY: 0.339   greenX: 0.143 greenY: 0.070
[     2.578] (II) fglrx(0): blueX: 0.282 blueY: 0.603   whiteX: 0.312 whiteY: 0.329
[     2.578] (II) fglrx(0): Supported established timings:
[     2.578] (II) fglrx(0): 640x480@60Hz
[     2.578] (II) fglrx(0): 800x600@56Hz
[     2.578] (II) fglrx(0): 800x600@60Hz
[     2.578] (II) fglrx(0): 1024x768@60Hz
[     2.578] (II) fglrx(0): Manufacturer's mask: 0
[     2.578] (II) fglrx(0): Supported standard timings:
[     2.578] (II) fglrx(0): #0: hsize: 1280  vsize 800  refresh: 60  vid: 129
[     2.578] (II) fglrx(0): #1: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[     2.578] (II) fglrx(0): #2: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[     2.578] (II) fglrx(0): #3: hsize: 1440  vsize 900  refresh: 60  vid: 149
[     2.578] (II) fglrx(0): #4: hsize: 1600  vsize 1200  refresh: 60  vid: 16553
[     2.578] (II) fglrx(0): #5: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 148.5 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[     2.578] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[     2.578] (II) fglrx(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[     2.578] (II) fglrx(0): Monitor name: SyncMaster
[     2.578] (II) fglrx(0): Serial No: HMBS500385
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 148.5 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 1920  h_sync: 2448  h_sync_end 2492 h_blank_end 2640 h_border: 0
[     2.578] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 74.2 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 1280  h_sync: 1390  h_sync_end 1430 h_blank_end 1650 h_border: 0
[     2.578] (II) fglrx(0): v_active: 720  v_sync: 725  v_sync_end 730 v_blanking: 750 v_border: 0
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 74.2 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 1280  h_sync: 1720  h_sync_end 1760 h_blank_end 1980 h_border: 0
[     2.578] (II) fglrx(0): v_active: 720  v_sync: 725  v_sync_end 730 v_blanking: 750 v_border: 0
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 27.0 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 720  h_sync: 732  h_sync_end 796 h_blank_end 864 h_border: 0
[     2.578] (II) fglrx(0): v_active: 576  v_sync: 581  v_sync_end 586 v_blanking: 625 v_border: 0
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 27.0 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 720  h_sync: 736  h_sync_end 798 h_blank_end 858 h_border: 0
[     2.578] (II) fglrx(0): v_active: 480  v_sync: 489  v_sync_end 495 v_blanking: 525 v_border: 0
[     2.578] (II) fglrx(0): Number of EDID sections to follow: 1
[     2.578] (II) fglrx(0): EDID (in hex):
[     2.578] (II) fglrx(0): 	00ffffffffffff004c2d24053232524c
[     2.578] (II) fglrx(0): 	1413010380301b782a3851a656241248
[     2.578] (II) fglrx(0): 	9a50542308008100814081809500a940
[     2.578] (II) fglrx(0): 	b30001010101023a801871382d40582c
[     2.578] (II) fglrx(0): 	4500dd0c1100001e000000fd00383c1e
[     2.578] (II) fglrx(0): 	5111000a202020202020000000fc0053
[     2.578] (II) fglrx(0): 	796e634d61737465720a2020000000ff
[     2.578] (II) fglrx(0): 	00484d42533530303338350a20200168
[     2.578] (II) fglrx(0): End of Display0 EDID data --------------------
[     2.578] (II) fglrx(0): EDID for output DFP1
[     2.578] (II) fglrx(0): EDID for output DFP2
[     2.578] (II) fglrx(0): EDID for output DFP3
[     2.578] (II) fglrx(0): EDID for output DFP4
[     2.578] (II) fglrx(0): EDID for output DFP5
[     2.578] (II) fglrx(0): EDID for output DFP6
[     2.578] (II) fglrx(0): EDID for output DFP7
[     2.578] (II) fglrx(0): EDID for output DFP8
[     2.578] (II) fglrx(0): EDID for output DFP9
[     2.578] (II) fglrx(0): EDID for output DFP10
[     2.578] (II) fglrx(0): Manufacturer: SAM  Model: 524  Serial#: 1280455218
[     2.578] (II) fglrx(0): Year: 2009  Week: 20
[     2.578] (II) fglrx(0): EDID Version: 1.3
[     2.578] (II) fglrx(0): Digital Display Input
[     2.578] (II) fglrx(0): Max Image Size [cm]: horiz.: 48  vert.: 27
[     2.578] (II) fglrx(0): Gamma: 2.20
[     2.578] (II) fglrx(0): DPMS capabilities: Off
[     2.578] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[     2.578] (II) fglrx(0): First detailed timing is preferred mode
[     2.578] (II) fglrx(0): redX: 0.648 redY: 0.339   greenX: 0.143 greenY: 0.070
[     2.578] (II) fglrx(0): blueX: 0.282 blueY: 0.603   whiteX: 0.312 whiteY: 0.329
[     2.578] (II) fglrx(0): Supported established timings:
[     2.578] (II) fglrx(0): 640x480@60Hz
[     2.578] (II) fglrx(0): 800x600@56Hz
[     2.578] (II) fglrx(0): 800x600@60Hz
[     2.578] (II) fglrx(0): 1024x768@60Hz
[     2.578] (II) fglrx(0): Manufacturer's mask: 0
[     2.578] (II) fglrx(0): Supported standard timings:
[     2.578] (II) fglrx(0): #0: hsize: 1280  vsize 800  refresh: 60  vid: 129
[     2.578] (II) fglrx(0): #1: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[     2.578] (II) fglrx(0): #2: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[     2.578] (II) fglrx(0): #3: hsize: 1440  vsize 900  refresh: 60  vid: 149
[     2.578] (II) fglrx(0): #4: hsize: 1600  vsize 1200  refresh: 60  vid: 16553
[     2.578] (II) fglrx(0): #5: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 148.5 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[     2.578] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[     2.578] (II) fglrx(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[     2.578] (II) fglrx(0): Monitor name: SyncMaster
[     2.578] (II) fglrx(0): Serial No: HMBS500385
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 148.5 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 1920  h_sync: 2448  h_sync_end 2492 h_blank_end 2640 h_border: 0
[     2.578] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 74.2 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 1280  h_sync: 1390  h_sync_end 1430 h_blank_end 1650 h_border: 0
[     2.578] (II) fglrx(0): v_active: 720  v_sync: 725  v_sync_end 730 v_blanking: 750 v_border: 0
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 74.2 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 1280  h_sync: 1720  h_sync_end 1760 h_blank_end 1980 h_border: 0
[     2.578] (II) fglrx(0): v_active: 720  v_sync: 725  v_sync_end 730 v_blanking: 750 v_border: 0
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 27.0 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 720  h_sync: 732  h_sync_end 796 h_blank_end 864 h_border: 0
[     2.578] (II) fglrx(0): v_active: 576  v_sync: 581  v_sync_end 586 v_blanking: 625 v_border: 0
[     2.578] (II) fglrx(0): Supported detailed timing:
[     2.578] (II) fglrx(0): clock: 27.0 MHz   Image Size:  477 x 268 mm
[     2.578] (II) fglrx(0): h_active: 720  h_sync: 736  h_sync_end 798 h_blank_end 858 h_border: 0
[     2.578] (II) fglrx(0): v_active: 480  v_sync: 489  v_sync_end 495 v_blanking: 525 v_border: 0
[     2.578] (II) fglrx(0): Number of EDID sections to follow: 1
[     2.578] (II) fglrx(0): EDID (in hex):
[     2.578] (II) fglrx(0): 	00ffffffffffff004c2d24053232524c
[     2.578] (II) fglrx(0): 	1413010380301b782a3851a656241248
[     2.578] (II) fglrx(0): 	9a50542308008100814081809500a940
[     2.578] (II) fglrx(0): 	b30001010101023a801871382d40582c
[     2.578] (II) fglrx(0): 	4500dd0c1100001e000000fd00383c1e
[     2.578] (II) fglrx(0): 	5111000a202020202020000000fc0053
[     2.578] (II) fglrx(0): 	796e634d61737465720a2020000000ff
[     2.578] (II) fglrx(0): 	00484d42533530303338350a20200168
[     2.579] (II) fglrx(0): Printing probed modes for output DFP10
[     2.579] (II) fglrx(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
[     2.579] (II) fglrx(0): Modeline "1920x1080"x50.0  148.50  1920 2448 2492 2640  1080 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1600x1200"x60.0  162.00  1600 1664 1856 2160  1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[     2.579] (II) fglrx(0): Modeline "1776x1000"x50.0  148.50  1776 2304 2348 2640  1000 1004 1009 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1680x1050"x50.0  148.50  1680 2448 2492 2640  1050 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[     2.579] (II) fglrx(0): Modeline "1400x1050"x60.0  162.00  1400 1664 1856 2160  1050 1201 1204 1250 +hsync +vsync (75.0 kHz)
[     2.579] (II) fglrx(0): Modeline "1400x1050"x50.0  148.50  1400 2448 2492 2640  1050 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1600x900"x60.0  162.00  1600 1664 1856 2160  900 1201 1204 1250 +hsync +vsync (75.0 kHz)
[     2.579] (II) fglrx(0): Modeline "1600x900"x50.0  148.50  1600 2448 2492 2640  900 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x1024"x50.0  148.50  1280 2448 2492 2640  1024 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[     2.579] (II) fglrx(0): Modeline "1440x900"x50.0  148.50  1440 2448 2492 2640  900 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1440x900"x60.0  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x960"x50.0  148.50  1280 2448 2492 2640  960 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x800"x50.0  148.50  1280 2448 2492 2640  800 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x800"x60.0   83.50  1280 1352 1480 1680  800 803 809 831 -hsync +vsync (49.7 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x768"x50.0  148.50  1280 2448 2492 2640  768 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x768"x60.0   83.50  1280 1352 1480 1680  768 803 809 831 -hsync +vsync (49.7 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x720"x60.0   74.25  1280 1390 1430 1650  720 725 730 750 +hsync +vsync (45.0 kHz)
[     2.579] (II) fglrx(0): Modeline "1280x720"x50.0   74.25  1280 1720 1760 1980  720 725 730 750 +hsync +vsync (37.5 kHz)
[     2.579] (II) fglrx(0): Modeline "1024x768"x50.0  148.50  1024 2448 2492 2640  768 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
[     2.579] (II) fglrx(0): Modeline "1152x648"x50.0   74.25  1152 1592 1632 1980  648 653 658 750 +hsync +vsync (37.5 kHz)
[     2.579] (II) fglrx(0): Modeline "800x600"x50.0  148.50  800 2448 2492 2640  600 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "800x600"x60.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
[     2.579] (II) fglrx(0): Modeline "800x600"x56.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
[     2.579] (II) fglrx(0): Modeline "720x576"x60.0  148.50  720 2008 2052 2200  576 1084 1089 1125 +hsync +vsync (67.5 kHz)
[     2.579] (II) fglrx(0): Modeline "720x576"x50.0   27.00  720 732 796 864  576 581 586 625 -hsync -vsync (31.2 kHz)
[     2.579] (II) fglrx(0): Modeline "720x480"x50.0  148.50  720 2448 2492 2640  480 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "720x480"x59.9   27.00  720 736 798 858  480 489 495 525 -hsync -vsync (31.5 kHz)
[     2.579] (II) fglrx(0): Modeline "640x480"x50.0  148.50  640 2448 2492 2640  480 1084 1089 1125 +hsync +vsync (56.2 kHz)
[     2.579] (II) fglrx(0): Modeline "640x480"x60.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
[     2.579] (II) fglrx(0): EDID for output CRT1
[     2.579] (II) fglrx(0): Output DFP1 disconnected
[     2.579] (II) fglrx(0): Output DFP2 disconnected
[     2.579] (II) fglrx(0): Output DFP3 disconnected
[     2.579] (II) fglrx(0): Output DFP4 disconnected
[     2.579] (II) fglrx(0): Output DFP5 disconnected
[     2.579] (II) fglrx(0): Output DFP6 disconnected
[     2.579] (II) fglrx(0): Output DFP7 disconnected
[     2.579] (II) fglrx(0): Output DFP8 disconnected
[     2.579] (II) fglrx(0): Output DFP9 disconnected
[     2.579] (II) fglrx(0): Output DFP10 connected
[     2.579] (II) fglrx(0): Output CRT1 disconnected
[     2.579] (II) fglrx(0): Using exact sizes for initial modes
[     2.579] (II) fglrx(0): Output DFP10 using initial mode 1920x1080
[     2.579] (II) fglrx(0): DPI set to (96, 96)
[     2.579] (II) fglrx(0): Eyefinity capable adapter detected.
[     2.579] (II) fglrx(0): Adapter AMD Radeon HD 7800 Series  has 6 configurable heads and 1 displays connected.
[     2.579] (==) fglrx(0):  PseudoColor visuals disabled
[     2.579] (II) Loading sub module "ramdac"
[     2.579] (II) LoadModule: "ramdac"
[     2.579] (II) Module "ramdac" already built-in
[     2.579] (==) fglrx(0): NoDRI = NO
[     2.579] (==) fglrx(0): Capabilities: 0x00000000
[     2.579] (==) fglrx(0): CapabilitiesEx: 0x00000000
[     2.579] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
[     2.579] (==) fglrx(0): UseFastTLS=0
[     2.579] (II) fglrx(0): Desktop Vsync is enabled.
[     2.579] (--) Depth 24 pixmap format is 32 bpp
[     2.579] (II) Loading extension ATIFGLRXDRI
[     2.579] (II) fglrx(0): doing swlDriScreenInit
[     2.579] (II) fglrx(0): swlDriScreenInit for fglrx driver
[     2.579] ukiDynamicMajor: found major device number 251
[     2.579] ukiDynamicMajor: found major device number 251
[     2.579] ukiDynamicMajor: found major device number 251
[     2.579] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[     2.579] ukiOpenDevice: node name is /dev/ati/card0
[     2.579] ukiOpenDevice: open result is 12, (OK)
[     2.579] ukiOpenByBusid: ukiOpenMinor returns 12
[     2.579] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[     2.579] (II) fglrx(0): [uki] DRM interface version 1.0
[     2.579] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:6:0:0"
[     2.579] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
[     2.579] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0x7f1426d74000
[     2.579] (II) fglrx(0): [uki] framebuffer handle = 0x3000
[     2.579] (II) fglrx(0): [uki] added 1 reserved context for kernel
[     2.579] (II) fglrx(0): swlDriScreenInit done
[     2.579] (II) fglrx(0): Kernel Module Version Information:
[     2.579] (II) fglrx(0):     Name: fglrx
[     2.579] (II) fglrx(0):     Version: 8.98.2
[     2.579] (II) fglrx(0):     Date: Jul 27 2012
[     2.579] (II) fglrx(0):     Desc: AMD FireGL DRM kernel module
[     2.579] (II) fglrx(0): Kernel Module version matches driver.
[     2.579] (II) fglrx(0): Kernel Module Build Time Information:
[     2.579] (II) fglrx(0):     Build-Kernel UTS_RELEASE:        3.5.3-1-ARCH
[     2.579] (II) fglrx(0):     Build-Kernel MODVERSIONS:        no
[     2.579] (II) fglrx(0):     Build-Kernel __SMP__:            no
[     2.579] (II) fglrx(0):     Build-Kernel PAGE_SIZE:          0x1000
[     2.579] (II) fglrx(0): [uki] register handle = 0x00004000
[     2.589] (II) fglrx(0): DRI initialization successfull
[     2.590] (II) fglrx(0): FBADPhys: 0xf400000000 FBMappedSize: 0x010e0000
[     2.591] (==) fglrx(0): Backing store disabled
[     2.591] (II) Loading extension FGLRXEXTENSION
[     2.591] (**) fglrx(0): DPMS enabled
[     2.591] (II) fglrx(0): Initialized in-driver Xinerama extension
[     2.591] (**) fglrx(0): Textured Video is enabled.
[     2.591] (II) LoadModule: "glesx"
[     2.591] (II) Loading /usr/lib/xorg/modules/glesx.so
[     2.601] (II) Module glesx: vendor="X.Org Foundation"
[     2.601] 	compiled for 1.4.99.906, module version = 1.0.0
[     2.601] (II) Loading extension GLESX
[     2.601] (II) fglrx(0): GLESX enableFlags = 592
[     2.602] (II) fglrx(0): GLESX is enabled
[     2.602] (II) LoadModule: "amdxmm"
[     2.602] (II) Loading /usr/lib/xorg/modules/amdxmm.so
[     2.603] (II) Module amdxmm: vendor="X.Org Foundation"
[     2.603] 	compiled for 1.4.99.906, module version = 2.0.0
[     2.615] (II) Loading extension AMDXVOPL
[     2.615] (II) Loading extension AMDXVBA
[     2.617] (II) fglrx(0): UVD feature is enabled(II) fglrx(0): 
[     2.618] (II) fglrx(0): Enable composite support successfully
[     2.618] (WW) fglrx(0): Option "VendorName" is not used
[     2.618] (WW) fglrx(0): Option "ModelName" is not used
[     2.618] (II) fglrx(0): X context handle = 0x1
[     2.618] (II) fglrx(0): [DRI] installation complete
[     2.618] (==) fglrx(0): Silken mouse enabled
[     2.618] (==) fglrx(0): Using HW cursor of display infrastructure!
[     2.618] (II) fglrx(0): Disabling in-server RandR and enabling in-driver RandR 1.2.
[     2.735] (II) fglrx(0): Framebuffer compression enabled: mcAddr=0xf407a40000 width=0xa00 height=0x3267
[     2.735] (--) RandR disabled
[     2.735] (II) Initializing built-in extension Generic Event Extension
[     2.735] (II) Initializing built-in extension SHAPE
[     2.735] (II) Initializing built-in extension MIT-SHM
[     2.735] (II) Initializing built-in extension XInputExtension
[     2.735] (II) Initializing built-in extension XTEST
[     2.735] (II) Initializing built-in extension BIG-REQUESTS
[     2.735] (II) Initializing built-in extension SYNC
[     2.735] (II) Initializing built-in extension XKEYBOARD
[     2.735] (II) Initializing built-in extension XC-MISC
[     2.735] (II) Initializing built-in extension SECURITY
[     2.735] (II) Initializing built-in extension XINERAMA
[     2.735] (II) Initializing built-in extension XFIXES
[     2.735] (II) Initializing built-in extension RENDER
[     2.735] (II) Initializing built-in extension RANDR
[     2.735] (II) Initializing built-in extension COMPOSITE
[     2.735] (II) Initializing built-in extension DAMAGE
[     2.736] ukiDynamicMajor: found major device number 251
[     2.736] ukiDynamicMajor: found major device number 251
[     2.736] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[     2.736] ukiOpenDevice: node name is /dev/ati/card0
[     2.736] ukiOpenDevice: open result is 13, (OK)
[     2.736] ukiOpenByBusid: ukiOpenMinor returns 13
[     2.736] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[     2.842] (II) AIGLX: Loaded and initialized OpenGL driver(II) GLX: Initialized DRI GL provider for screen 0
[     2.857] (II) fglrx(0): Enable the clock gating!
[     2.872] (II) fglrx(0): Desktop Vsync is enabled.
[     2.872] (II) fglrx(0): Setting screen physical size to 508 x 285
[     2.901] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[     2.901] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[     2.901] (II) LoadModule: "evdev"
[     2.901] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[     2.902] (II) Module evdev: vendor="X.Org Foundation"
[     2.902] 	compiled for 1.12.3.901, module version = 2.7.3
[     2.902] 	Module class: X.Org XInput Driver
[     2.902] 	ABI class: X.Org XInput driver, version 16.0
[     2.902] (II) Using input driver 'evdev' for 'Power Button'
[     2.902] (**) Power Button: always reports core events
[     2.902] (**) evdev: Power Button: Device: "/dev/input/event2"
[     2.902] (--) evdev: Power Button: Vendor 0 Product 0x1
[     2.902] (--) evdev: Power Button: Found keys
[     2.902] (II) evdev: Power Button: Configuring as keyboard
[     2.902] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[     2.902] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[     2.902] (**) Option "xkb_rules" "evdev"
[     2.902] (**) Option "xkb_model" "evdev"
[     2.902] (**) Option "xkb_layout" "us"
[     2.902] (**) Option "xkb_variant" "dvp"
[     2.913] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[     2.913] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[     2.913] (II) Using input driver 'evdev' for 'Power Button'
[     2.913] (**) Power Button: always reports core events
[     2.913] (**) evdev: Power Button: Device: "/dev/input/event1"
[     2.913] (--) evdev: Power Button: Vendor 0 Product 0x1
[     2.913] (--) evdev: Power Button: Found keys
[     2.913] (II) evdev: Power Button: Configuring as keyboard
[     2.913] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1"
[     2.913] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[     2.913] (**) Option "xkb_rules" "evdev"
[     2.913] (**) Option "xkb_model" "evdev"
[     2.913] (**) Option "xkb_layout" "us"
[     2.913] (**) Option "xkb_variant" "dvp"
[     2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=11 (/dev/input/event14)
[     2.913] (II) No input driver specified, ignoring this device.
[     2.913] (II) This device may have been added with another device file.
[     2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=10 (/dev/input/event15)
[     2.913] (II) No input driver specified, ignoring this device.
[     2.913] (II) This device may have been added with another device file.
[     2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=9 (/dev/input/event16)
[     2.913] (II) No input driver specified, ignoring this device.
[     2.913] (II) This device may have been added with another device file.
[     2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=8 (/dev/input/event17)
[     2.913] (II) No input driver specified, ignoring this device.
[     2.913] (II) This device may have been added with another device file.
[     2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=7 (/dev/input/event18)
[     2.913] (II) No input driver specified, ignoring this device.
[     2.913] (II) This device may have been added with another device file.
[     2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=3 (/dev/input/event19)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Surround (/dev/input/event10)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Front (/dev/input/event11)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event4)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event5)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event6)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event7)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Side (/dev/input/event8)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out CLFE (/dev/input/event9)
[     2.914] (II) No input driver specified, ignoring this device.
[     2.914] (II) This device may have been added with another device file.
[     2.914] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event12)
[     2.914] (**) Logitech USB Receiver: Applying InputClass "evdev pointer catchall"
[     2.914] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[     2.914] (**) Logitech USB Receiver: always reports core events
[     2.914] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event12"
[     2.914] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc52f
[     2.914] (--) evdev: Logitech USB Receiver: Found 20 mouse buttons
[     2.914] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[     2.914] (--) evdev: Logitech USB Receiver: Found relative axes
[     2.914] (--) evdev: Logitech USB Receiver: Found x and y relative axes
[     2.914] (II) evdev: Logitech USB Receiver: Configuring as mouse
[     2.914] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[     2.914] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[     2.914] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[     2.914] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.0/input/input12/event12"
[     2.914] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: MOUSE, id 8)
[     2.914] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[     2.915] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[     2.915] (**) Logitech USB Receiver: (accel) acceleration profile 0
[     2.915] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[     2.915] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[     2.915] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/mouse0)
[     2.915] (II) No input driver specified, ignoring this device.
[     2.915] (II) This device may have been added with another device file.
[     2.915] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event13)
[     2.915] (**) Logitech USB Receiver: Applying InputClass "evdev keyboard catchall"
[     2.915] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[     2.915] (**) Logitech USB Receiver: always reports core events
[     2.915] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event13"
[     2.915] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc52f
[     2.915] (--) evdev: Logitech USB Receiver: Found 1 mouse buttons
[     2.915] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[     2.915] (--) evdev: Logitech USB Receiver: Found relative axes
[     2.915] (II) evdev: Logitech USB Receiver: Forcing relative x/y axes to exist.
[     2.915] (--) evdev: Logitech USB Receiver: Found absolute axes
[     2.915] (II) evdev: Logitech USB Receiver: Forcing absolute x/y axes to exist.
[     2.915] (--) evdev: Logitech USB Receiver: Found keys
[     2.915] (II) evdev: Logitech USB Receiver: Configuring as mouse
[     2.915] (II) evdev: Logitech USB Receiver: Configuring as keyboard
[     2.915] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[     2.915] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[     2.915] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[     2.915] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.1/input/input13/event13"
[     2.915] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD, id 9)
[     2.915] (**) Option "xkb_rules" "evdev"
[     2.915] (**) Option "xkb_model" "evdev"
[     2.915] (**) Option "xkb_layout" "us"
[     2.915] (**) Option "xkb_variant" "dvp"
[     2.915] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[     2.915] (WW) evdev: Logitech USB Receiver: ignoring absolute axes.
[     2.915] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[     2.915] (**) Logitech USB Receiver: (accel) acceleration profile 0
[     2.915] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[     2.915] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[     2.915] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[     2.915] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[     2.915] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[     2.915] (**) AT Translated Set 2 keyboard: always reports core events
[     2.915] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[     2.915] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[     2.915] (--) evdev: AT Translated Set 2 keyboard: Found keys
[     2.915] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[     2.915] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[     2.915] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)
[     2.915] (**) Option "xkb_rules" "evdev"
[     2.915] (**) Option "xkb_model" "evdev"
[     2.915] (**) Option "xkb_layout" "us"
[     2.915] (**) Option "xkb_variant" "dvp"
[     2.915] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[     2.915] (II) No input driver specified, ignoring this device.
[     2.915] (II) This device may have been added with another device file.
[     2.917] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments
[     7.513] (II) fglrx(0): EDID vendor "SAM", prod id 1316
[     7.513] (II) fglrx(0): Using EDID range info for horizontal sync
[     7.513] (II) fglrx(0): Using EDID range info for vertical refresh
[     7.513] (II) fglrx(0): Printing DDC gathered Modelines:
[     7.513] (II) fglrx(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[     7.513] (II) fglrx(0): Modeline "1920x1080"x0.0  148.50  1920 2448 2492 2640  1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[     7.513] (II) fglrx(0): Modeline "1280x720"x0.0   74.25  1280 1390 1430 1650  720 725 730 750 +hsync +vsync (45.0 kHz e)
[     7.513] (II) fglrx(0): Modeline "1280x720"x0.0   74.25  1280 1720 1760 1980  720 725 730 750 +hsync +vsync (37.5 kHz e)
[     7.513] (II) fglrx(0): Modeline "720x576"x0.0   27.00  720 732 796 864  576 581 586 625 -hsync -vsync (31.2 kHz e)
[     7.513] (II) fglrx(0): Modeline "720x480"x0.0   27.00  720 736 798 858  480 489 495 525 -hsync -vsync (31.5 kHz e)
[     7.513] (II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[     7.513] (II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[     7.513] (II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[     7.513] (II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[     7.513] (II) fglrx(0): Modeline "1280x800"x0.0   71.00  1280 1328 1360 1440  800 803 809 823 +hsync -vsync (49.3 kHz e)
[     7.513] (II) fglrx(0): Modeline "1280x960"x0.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz e)
[     7.513] (II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[     7.513] (II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz e)
[     7.513] (II) fglrx(0): Modeline "1600x1200"x0.0  162.00  1600 1664 1856 2160  1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[     7.513] (II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
[    10.738] (II) fglrx(0): EDID vendor "SAM", prod id 1316
[    10.738] (II) fglrx(0): Using hsync ranges from config file
[    10.738] (II) fglrx(0): Using vrefresh ranges from config file
[    10.738] (II) fglrx(0): Printing DDC gathered Modelines:
[    10.738] (II) fglrx(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[    10.738] (II) fglrx(0): Modeline "1920x1080"x0.0  148.50  1920 2448 2492 2640  1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[    10.738] (II) fglrx(0): Modeline "1280x720"x0.0   74.25  1280 1390 1430 1650  720 725 730 750 +hsync +vsync (45.0 kHz e)
[    10.738] (II) fglrx(0): Modeline "1280x720"x0.0   74.25  1280 1720 1760 1980  720 725 730 750 +hsync +vsync (37.5 kHz e)
[    10.738] (II) fglrx(0): Modeline "720x576"x0.0   27.00  720 732 796 864  576 581 586 625 -hsync -vsync (31.2 kHz e)
[    10.738] (II) fglrx(0): Modeline "720x480"x0.0   27.00  720 736 798 858  480 489 495 525 -hsync -vsync (31.5 kHz e)
[    10.738] (II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    10.738] (II) fglrx(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    10.738] (II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    10.738] (II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    10.738] (II) fglrx(0): Modeline "1280x800"x0.0   71.00  1280 1328 1360 1440  800 803 809 823 +hsync -vsync (49.3 kHz e)
[    10.738] (II) fglrx(0): Modeline "1280x960"x0.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz e)
[    10.738] (II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    10.738] (II) fglrx(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz e)
[    10.738] (II) fglrx(0): Modeline "1600x1200"x0.0  162.00  1600 1664 1856 2160  1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[    10.738] (II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)

And here's the Xorg.conf:

Section "ServerLayout"
        Identifier     "aticonfig Layout"
        Screen      0  "aticonfig-Screen[0]-0" 0 0
EndSection

Section "Module"
EndSection

Section "Monitor"
        Identifier   "aticonfig-Monitor[0]-0"
        Option      "VendorName" "ATI Proprietary Driver"
        Option      "ModelName" "Generic Autodetecting Monitor"
        Option      "DPMS" "true"
EndSection

Section "Device"
        Identifier  "aticonfig-Device[0]-0"
        Driver      "fglrx"
        BusID       "PCI:6:0:0"
        Option      "OpenGLOverlay" "0"
EndSection

Section "Screen"
        Identifier "aticonfig-Screen[0]-0"
        Device     "aticonfig-Device[0]-0"
        Monitor    "aticonfig-Monitor[0]-0"
        DefaultDepth     24
        SubSection "Display"
                Viewport   0 0
                Depth     24
        EndSubSection
EndSection
Section "DRI"
        Mode 0666
EndSection

Funny thing is, in the previous log, PCI:0@7:0:0 is probed, but in second log, its PCI:0@6:0:0, which matches with this file, and the graphics card is detected.
Any idea why the other PCI port is being probed first??

Last edited by hdhiman (2012-09-27 14:26:54)

Offline

#8 2012-09-28 07:38:50

hdhiman
Member
Registered: 2009-09-05
Posts: 52

Re: Cannot boot to X (kdm) unless reboot.

Does it have anything to do with acpid?
I'm not using it at present.

Offline

Board footer

Powered by FluxBB