Cannot load X from within a new VM.

graysky · 2012-09-28 08:02:41

Followed the wiki and have spun up a new i686 Arch VM (Virtualbox). I seemed to have hit a wall and cannot get X to load to save my life.

I have the following required packages installed on the VM in addition to the standard Xorg packages:
virtualbox-guest-modules
virtualbox-guest-utils

Required modules are loaded:

$ lsmod | grep vbox
vboxvideo               1233  0 
vboxsf                 34250  0 
vboxguest             150515  1 vboxsf
drm                   182234  1 vboxvideo

But when I attempt to go graphical:

$ xinit


X.Org X Server 1.12.4
Release Date: 2012-08-27
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.4.8-1-ARCH i686 
Current Operating System: Linux nano 3.5.4-1-ARCH #1 SMP PREEMPT Sat Sep 15 13:04:04 UTC 2012 i686
Kernel command line: root=/dev/sda3 ro init=/bin/systemd initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux 
Build Date: 27 August 2012  08:08:29AM
 
Current version of pixman: 0.26.2
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Fri Sep 28 04:07:11 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"
xinit: connection to X server lost

waiting for X server to shut down Server terminated successfully (0). Closing log file.

If I grep out the errors:

$ grep \(EE /var/log/Xorg.0.log 
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[   219.974] (EE) Failed to load module "vesa" (module does not exist, 0)
[   219.974] (EE) Failed to load module "fbdev" (module does not exist, 0)
[   220.297] (EE) AIGLX error: vboxvideo does not export required DRI extension
[   220.297] (EE) AIGLX: reverting to software rendering

Here is the log but I am at a loss.

$ cat Xorg.0.log 
[   116.729] 
X.Org X Server 1.12.4
Release Date: 2012-08-27
[   116.732] X Protocol Version 11, Revision 0
[   116.733] Build Operating System: Linux 3.4.8-1-ARCH i686 
[   116.735] Current Operating System: Linux nano 3.5.4-1-ARCH #1 SMP PREEMPT Sat Sep 15 13:04:04 UTC 2012 i686
[   116.735] Kernel command line: root=/dev/sda3 ro init=/bin/systemd initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux 
[   116.738] Build Date: 27 August 2012  08:08:29AM
[   116.739]  
[   116.740] Current version of pixman: 0.26.2
[   116.741] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[   116.741] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[   116.744] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Sep 28 04:05:26 2012
[   116.744] (==) Using config directory: "/etc/X11/xorg.conf.d"
[   116.744] (==) No Layout section.  Using the first Screen section.
[   116.744] (==) No screen section available. Using defaults.
[   116.744] (**) |-->Screen "Default Screen Section" (0)
[   116.744] (**) |   |-->Monitor "<default monitor>"
[   116.744] (==) No monitor specified for screen "Default Screen Section".
	Using a default monitor configuration.
[   116.744] (==) Automatically adding devices
[   116.744] (==) Automatically enabling devices
[   116.753] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[   116.753] 	Entry deleted from font path.
[   116.753] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[   116.753] 	Entry deleted from font path.
[   116.753] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[   116.754] 	Entry deleted from font path.
[   116.754] 	(Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[   116.754] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[   116.754] 	Entry deleted from font path.
[   116.754] 	(Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[   116.754] (==) FontPath set to:
	/usr/share/fonts/misc/,
	/usr/share/fonts/TTF/
[   116.754] (==) ModulePath set to "/usr/lib/xorg/modules"
[   116.754] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[   116.754] (II) Loader magic: 0x82225a0
[   116.754] (II) Module ABI versions:
[   116.754] 	X.Org ANSI C Emulation: 0.4
[   116.754] 	X.Org Video Driver: 12.1
[   116.754] 	X.Org XInput driver : 16.0
[   116.754] 	X.Org Server Extension : 6.0
[   116.757] (--) PCI:*(0:0:2:0) 80ee:beef:0000:0000 rev 0, Mem @ 0xe0000000/33554432
[   116.757] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[   116.757] (II) LoadModule: "extmod"
[   116.770] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[   116.775] (II) Module extmod: vendor="X.Org Foundation"
[   116.775] 	compiled for 1.12.4, module version = 1.0.0
[   116.776] 	Module class: X.Org Server Extension
[   116.776] 	ABI class: X.Org Server Extension, version 6.0
[   116.776] (II) Loading extension MIT-SCREEN-SAVER
[   116.776] (II) Loading extension XFree86-VidModeExtension
[   116.776] (II) Loading extension XFree86-DGA
[   116.776] (II) Loading extension DPMS
[   116.776] (II) Loading extension XVideo
[   116.776] (II) Loading extension XVideo-MotionCompensation
[   116.776] (II) Loading extension X-Resource
[   116.776] (II) LoadModule: "dbe"
[   116.776] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[   116.781] (II) Module dbe: vendor="X.Org Foundation"
[   116.781] 	compiled for 1.12.4, module version = 1.0.0
[   116.781] 	Module class: X.Org Server Extension
[   116.781] 	ABI class: X.Org Server Extension, version 6.0
[   116.781] (II) Loading extension DOUBLE-BUFFER
[   116.781] (II) LoadModule: "glx"
[   116.781] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[   116.798] (II) Module glx: vendor="X.Org Foundation"
[   116.798] 	compiled for 1.12.4, module version = 1.0.0
[   116.798] 	ABI class: X.Org Server Extension, version 6.0
[   116.798] (==) AIGLX enabled
[   116.798] (II) Loading extension GLX
[   116.798] (II) LoadModule: "record"
[   116.798] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[   116.799] (II) Module record: vendor="X.Org Foundation"
[   116.799] 	compiled for 1.12.4, module version = 1.13.0
[   116.799] 	Module class: X.Org Server Extension
[   116.799] 	ABI class: X.Org Server Extension, version 6.0
[   116.799] (II) Loading extension RECORD
[   116.799] (II) LoadModule: "dri"
[   116.799] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[   116.808] (II) Module dri: vendor="X.Org Foundation"
[   116.808] 	compiled for 1.12.4, module version = 1.0.0
[   116.808] 	ABI class: X.Org Server Extension, version 6.0
[   116.808] (II) Loading extension XFree86-DRI
[   116.808] (II) LoadModule: "dri2"
[   116.808] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[   116.809] (II) Module dri2: vendor="X.Org Foundation"
[   116.809] 	compiled for 1.12.4, module version = 1.2.0
[   116.809] 	ABI class: X.Org Server Extension, version 6.0
[   116.809] (II) Loading extension DRI2
[   116.809] (==) Matched vboxvideo as autoconfigured driver 0
[   116.809] (==) Matched vesa as autoconfigured driver 1
[   116.809] (==) Matched fbdev as autoconfigured driver 2
[   116.809] (==) Assigned the driver to the xf86ConfigLayout
[   116.809] (II) LoadModule: "vboxvideo"
[   116.809] (II) Loading /usr/lib/xorg/modules/drivers/vboxvideo.so
[   116.822] (II) Module vboxvideo: vendor="Oracle Corporation"
[   116.822] 	compiled for 10.12.0, module version = 1.0.1
[   116.822] 	Module class: X.Org Video Driver
[   116.822] 	ABI class: X.Org Video Driver, version 12.0
[   116.822] (**) Load address of symbol "VBOXVIDEO" is 0xb7196c20
[   116.822] (II) LoadModule: "vesa"
[   116.831] (WW) Warning, couldn't open module vesa
[   116.831] (II) UnloadModule: "vesa"
[   116.831] (II) Unloading vesa
[   116.831] (EE) Failed to load module "vesa" (module does not exist, 0)
[   116.831] (II) LoadModule: "fbdev"
[   116.832] (WW) Warning, couldn't open module fbdev
[   116.832] (II) UnloadModule: "fbdev"
[   116.832] (II) Unloading fbdev
[   116.832] (EE) Failed to load module "fbdev" (module does not exist, 0)
[   116.832] (II) VBoxVideo: guest driver for VirtualBox: vbox
[   116.832] (--) using VT number 2

[   116.841] (II) VBoxVideo(0): VirtualBox guest additions video driver version 4.2.0_OSE
[   116.841] (II) Loading sub module "ramdac"
[   116.841] (II) LoadModule: "ramdac"
[   116.841] (II) Module "ramdac" already built-in
[   116.841] (II) Loading sub module "fb"
[   116.841] (II) LoadModule: "fb"
[   116.841] (II) Loading /usr/lib/xorg/modules/libfb.so
[   116.847] (II) Module fb: vendor="X.Org Foundation"
[   116.847] 	compiled for 1.12.4, module version = 1.0.0
[   116.847] 	ABI class: X.Org ANSI C Emulation, version 0.4
[   116.847] (II) Loading sub module "shadowfb"
[   116.847] (II) LoadModule: "shadowfb"
[   116.847] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[   116.851] (II) Module shadowfb: vendor="X.Org Foundation"
[   116.851] 	compiled for 1.12.4, module version = 1.0.0
[   116.851] 	ABI class: X.Org ANSI C Emulation, version 0.4
[   116.851] (II) Loading sub module "vgahw"
[   116.851] (II) LoadModule: "vgahw"
[   116.851] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[   116.858] (II) Module vgahw: vendor="X.Org Foundation"
[   116.858] 	compiled for 1.12.4, module version = 0.1.0
[   116.858] 	ABI class: X.Org Video Driver, version 12.1
[   116.858] (II) Loading sub module "dri"
[   116.858] (II) LoadModule: "dri"
[   116.858] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[   116.858] (II) Module dri: vendor="X.Org Foundation"
[   116.858] 	compiled for 1.12.4, module version = 1.0.0
[   116.858] 	ABI class: X.Org Server Extension, version 6.0
[   116.858] (II) VBoxVideo(0): Creating default Display subsection in Screen section
	"Default Screen Section" for depth/fbbpp 24/32
[   116.859] (==) VBoxVideo(0): Depth 24, (--) framebuffer bpp 32
[   116.859] (--) VBoxVideo(0): Virtual size is 32000x32000 (pitch 32000)
[   116.859] (**) VBoxVideo(0):  Built-in mode "VBoxInitialMode": 47.8 MHz (scaled from 0.0 MHz), 46.4 kHz, 60.0 Hz
[   116.859] (II) VBoxVideo(0): Modeline "VBoxInitialMode"x0.0   47.83  1024 1026 1028 1030  768 770 772 774 (46.4 kHz b)
[   116.859] (**) VBoxVideo(0):  Built-in mode "VBoxDynamicMode": 47.8 MHz (scaled from 0.0 MHz), 46.4 kHz, 60.0 Hz
[   116.859] (II) VBoxVideo(0): Modeline "VBoxDynamicMode"x0.0   47.83  1024 1026 1028 1030  768 770 772 774 (46.4 kHz b)
[   116.859] (**) VBoxVideo(0):  Built-in mode "VBoxDynamicMode": 47.8 MHz (scaled from 0.0 MHz), 46.4 kHz, 60.0 Hz
[   116.859] (II) VBoxVideo(0): Modeline "VBoxDynamicMode"x0.0   47.83  1024 1026 1028 1030  768 770 772 774 (46.4 kHz b)
[   116.859] (**) VBoxVideo(0):  Built-in mode "VBox-1024x768": 47.8 MHz (scaled from 0.0 MHz), 46.4 kHz, 60.0 Hz
[   116.859] (II) VBoxVideo(0): Modeline "VBox-1024x768"x0.0   47.83  1024 1026 1028 1030  768 770 772 774 (46.4 kHz b)
[   116.859] (**) VBoxVideo(0):  Built-in mode "VBox-800x600": 29.3 MHz (scaled from 0.0 MHz), 36.4 kHz, 60.0 Hz
[   116.859] (II) VBoxVideo(0): Modeline "VBox-800x600"x0.0   29.31  800 802 804 806  600 602 604 606 (36.4 kHz b)
[   116.859] (**) VBoxVideo(0):  Built-in mode "VBox-640x480": 18.8 MHz (scaled from 0.0 MHz), 29.2 kHz, 60.0 Hz
[   116.859] (II) VBoxVideo(0): Modeline "VBox-640x480"x0.0   18.84  640 642 644 646  480 482 484 486 (29.2 kHz b)
[   116.859] (II) VBoxVideo(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0
[   116.859] (==) VBoxVideo(0): RGB weight 888
[   116.859] (==) VBoxVideo(0): Default visual is TrueColor
[   116.859] (==) VBoxVideo(0): Using gamma correction (1.0, 1.0, 1.0)
[   116.859] (==) VBoxVideo(0): DPI set to (96, 96)
[   116.859] (--) Depth 24 pixmap format is 32 bpp
[   117.176] drmOpenDevice: node name is /dev/dri/card0
[   117.177] drmOpenDevice: open result is 11, (OK)
[   117.177] drmOpenDevice: node name is /dev/dri/card0
[   117.177] drmOpenDevice: open result is 11, (OK)
[   117.177] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[   117.177] drmOpenDevice: node name is /dev/dri/card0
[   117.177] drmOpenDevice: open result is 11, (OK)
[   117.177] drmOpenByBusid: drmOpenMinor returns 11
[   117.177] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[   117.177] (II) [drm] DRM interface version 1.4
[   117.177] (II) [drm] DRM open master succeeded.
[   117.177] (II) VBoxVideo(0): [drm] Using the DRM lock SAREA also for drawables.
[   117.177] (II) VBoxVideo(0): [drm] framebuffer handle = 0xe0000000
[   117.177] (II) VBoxVideo(0): [drm] added 1 reserved context for kernel
[   117.177] (II) VBoxVideo(0): X context handle = 0x1
[   117.177] (II) VBoxVideo(0): [drm] installed DRM signal handler
[   117.177] (II) VBoxVideo(0): visual configurations initialized
[   117.188] (II) VBoxVideo(0): Requested monitor count: 1
[   117.189] (II) VBoxVideo(0): Output VBOX0 has no monitor section
[   117.189] (II) VBoxVideo(0): Output VBOX0 has no monitor section
[   117.189] (II) VBoxVideo(0): EDID for output VBOX0
[   117.189] (II) VBoxVideo(0): Manufacturer: VBX  Model: 0  Serial#: 50332672
[   117.189] (II) VBoxVideo(0): Year: 1990  Week: 1
[   117.189] (II) VBoxVideo(0): EDID Version: 1.3
[   117.189] (II) VBoxVideo(0): Digital Display Input
[   117.189] (II) VBoxVideo(0): Indeterminate output size
[   117.189] (II) VBoxVideo(0): Gamma: 2.20
[   117.189] (II) VBoxVideo(0): DPMS capabilities: StandBy Suspend Off
[   117.189] (II) VBoxVideo(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[   117.189] (II) VBoxVideo(0): Default color space is primary color space
[   117.189] (II) VBoxVideo(0): First detailed timing is preferred mode
[   117.189] (II) VBoxVideo(0): redX: 0.640 redY: 0.330   greenX: 0.300 greenY: 0.600
[   117.189] (II) VBoxVideo(0): blueX: 0.150 blueY: 0.060   whiteX: 0.312 whiteY: 0.329
[   117.189] (II) VBoxVideo(0): Manufacturer's mask: 0
[   117.189] (II) VBoxVideo(0): Supported detailed timing:
[   117.189] (II) VBoxVideo(0): clock: 47.8 MHz   Image Size:  0 x 0 mm
[   117.189] (II) VBoxVideo(0): h_active: 1024  h_sync: 1026  h_sync_end 1028 h_blank_end 1030 h_border: 0
[   117.189] (II) VBoxVideo(0): v_active: 768  v_sync: 770  v_sync_end 772 v_blanking: 774 v_border: 0
[   117.189] (II) VBoxVideo(0): Ranges: V min: 0 V max: 200 Hz, H min: 0 H max: 200 kHz, PixClock max 1005 MHz
[   117.189] (II) VBoxVideo(0): Monitor name: VBOX monitor
[   117.189] (II) VBoxVideo(0): EDID (in hex):
[   117.189] (II) VBoxVideo(0): 	00ffffffffffff005858000000040003
[   117.189] (II) VBoxVideo(0): 	0100010380000078eeee91a3544c9926
[   117.189] (II) VBoxVideo(0): 	0f505400000001010101010101010101
[   117.189] (II) VBoxVideo(0): 	010101010101af120006400006300202
[   117.189] (II) VBoxVideo(0): 	2200000000000000000000fd0000c800
[   117.189] (II) VBoxVideo(0): 	c864000a202020202020000000fc0056
[   117.189] (II) VBoxVideo(0): 	424f58206d6f6e69746f720a00000010
[   117.189] (II) VBoxVideo(0): 	000a20202020202020202020202000fb
[   117.189] (II) VBoxVideo(0): EDID vendor "VBX", prod id 0
[   117.189] (II) VBoxVideo(0): DDCModeFromDetailedTiming: 1024x768 Warning: We only handle separate sync.
[   117.189] (II) VBoxVideo(0): Using hsync ranges from config file
[   117.189] (II) VBoxVideo(0): Using vrefresh ranges from config file
[   117.189] (II) VBoxVideo(0): Printing DDC gathered Modelines:
[   117.189] (II) VBoxVideo(0): Modeline "1024x768"x0.0   47.83  1024 1026 1028 1030  768 770 772 774 -hsync -vsync (46.4 kHz eP)
[   117.189] (II) VBoxVideo(0): Printing probed modes for output VBOX0
[   117.189] (II) VBoxVideo(0): Modeline "1024x768"x60.0   47.83  1024 1026 1028 1030  768 770 772 774 (46.4 kHz Pb)
[   117.189] (II) VBoxVideo(0): Modeline "800x600"x60.0   29.31  800 802 804 806  600 602 604 606 (36.4 kHz b)
[   117.189] (II) VBoxVideo(0): Modeline "640x480"x60.0   18.84  640 642 644 646  480 482 484 486 (29.2 kHz b)
[   117.189] (II) VBoxVideo(0): Output VBOX0 connected
[   117.189] (II) VBoxVideo(0): Using exact sizes for initial modes
[   117.189] (II) VBoxVideo(0): Output VBOX0 using initial mode 1024x768
[   117.189] (II) VBoxVideo(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[   117.189] (II) VBoxVideo(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[   117.190] (==) VBoxVideo(0): DPMS enabled
[   117.190] (II) VBoxVideo(0): [DRI] installation complete
[   117.190] (--) RandR disabled
[   117.190] (II) Initializing built-in extension Generic Event Extension
[   117.190] (II) Initializing built-in extension SHAPE
[   117.190] (II) Initializing built-in extension MIT-SHM
[   117.190] (II) Initializing built-in extension XInputExtension
[   117.190] (II) Initializing built-in extension XTEST
[   117.190] (II) Initializing built-in extension BIG-REQUESTS
[   117.190] (II) Initializing built-in extension SYNC
[   117.190] (II) Initializing built-in extension XKEYBOARD
[   117.190] (II) Initializing built-in extension XC-MISC
[   117.190] (II) Initializing built-in extension SECURITY
[   117.190] (II) Initializing built-in extension XINERAMA
[   117.190] (II) Initializing built-in extension XFIXES
[   117.190] (II) Initializing built-in extension RENDER
[   117.190] (II) Initializing built-in extension RANDR
[   117.190] (II) Initializing built-in extension COMPOSITE
[   117.190] (II) Initializing built-in extension DAMAGE
[   117.201] (II) AIGLX: Screen 0 is not DRI2 capable
[   117.201] drmOpenDevice: node name is /dev/dri/card0
[   117.201] drmOpenDevice: open result is 12, (OK)
[   117.201] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[   117.201] drmOpenDevice: node name is /dev/dri/card0
[   117.201] drmOpenDevice: open result is 12, (OK)
[   117.202] drmOpenByBusid: drmOpenMinor returns 12
[   117.202] drmOpenByBusid: Interface 1.4 failed, trying 1.1
[   117.202] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[   117.263] (II) Next line is added to allow vboxvideo_drv.so to appear as whitelisted driver
[   117.263] (II) The file referenced, is *NOT* loaded
[   117.263] (II) Loading /usr/lib/xorg/modules/drivers//ati_drv.so
[   117.263] (EE) AIGLX error: vboxvideo does not export required DRI extension
[   117.263] (EE) AIGLX: reverting to software rendering
[   117.539] (II) AIGLX: Loaded and initialized swrast
[   117.539] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[   117.539] (II) VBoxVideo(0): Setting screen physical size to 270 x 203
[   117.733] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[   117.733] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[   117.733] (II) LoadModule: "evdev"
[   117.733] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   117.743] (II) Module evdev: vendor="X.Org Foundation"
[   117.743] 	compiled for 1.12.3.901, module version = 2.7.3
[   117.743] 	Module class: X.Org XInput Driver
[   117.743] 	ABI class: X.Org XInput driver, version 16.0
[   117.743] (II) Using input driver 'evdev' for 'Power Button'
[   117.743] (**) Power Button: always reports core events
[   117.743] (**) evdev: Power Button: Device: "/dev/input/event4"
[   117.743] (--) evdev: Power Button: Vendor 0 Product 0x1
[   117.743] (--) evdev: Power Button: Found keys
[   117.743] (II) evdev: Power Button: Configuring as keyboard
[   117.743] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[   117.743] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[   117.743] (**) Option "xkb_rules" "evdev"
[   117.743] (**) Option "xkb_model" "evdev"
[   117.743] (**) Option "xkb_layout" "us"
[   117.758] (II) config/udev: Adding input device Sleep Button (/dev/input/event5)
[   117.758] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[   117.758] (II) Using input driver 'evdev' for 'Sleep Button'
[   117.758] (**) Sleep Button: always reports core events
[   117.758] (**) evdev: Sleep Button: Device: "/dev/input/event5"
[   117.758] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[   117.758] (--) evdev: Sleep Button: Found keys
[   117.758] (II) evdev: Sleep Button: Configuring as keyboard
[   117.758] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSLPBN:00/input/input5/event5"
[   117.758] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 7)
[   117.758] (**) Option "xkb_rules" "evdev"
[   117.758] (**) Option "xkb_model" "evdev"
[   117.758] (**) Option "xkb_layout" "us"
[   117.759] (II) config/udev: Adding input device VirtualBox mouse integration (/dev/input/event2)
[   117.759] (**) VirtualBox mouse integration: Applying InputClass "evdev pointer catchall"
[   117.759] (II) Using input driver 'evdev' for 'VirtualBox mouse integration'
[   117.759] (**) VirtualBox mouse integration: always reports core events
[   117.759] (**) evdev: VirtualBox mouse integration: Device: "/dev/input/event2"
[   117.759] (--) evdev: VirtualBox mouse integration: Vendor 0x80ee Product 0xcafe
[   117.759] (--) evdev: VirtualBox mouse integration: Found 1 mouse buttons
[   117.759] (--) evdev: VirtualBox mouse integration: Found absolute axes
[   117.759] (--) evdev: VirtualBox mouse integration: Found x and y absolute axes
[   117.759] (--) evdev: VirtualBox mouse integration: Found absolute touchscreen
[   117.759] (II) evdev: VirtualBox mouse integration: Configuring as touchscreen
[   117.759] (**) evdev: VirtualBox mouse integration: YAxisMapping: buttons 4 and 5
[   117.759] (**) evdev: VirtualBox mouse integration: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[   117.759] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:04.0/input/input2/event2"
[   117.759] (II) XINPUT: Adding extended input device "VirtualBox mouse integration" (type: TOUCHSCREEN, id 8)
[   117.759] (II) evdev: VirtualBox mouse integration: initialized for absolute axes.
[   117.759] (**) VirtualBox mouse integration: (accel) keeping acceleration scheme 1
[   117.759] (**) VirtualBox mouse integration: (accel) acceleration profile 0
[   117.759] (**) VirtualBox mouse integration: (accel) acceleration factor: 2.000
[   117.759] (**) VirtualBox mouse integration: (accel) acceleration threshold: 4
[   117.759] (II) config/udev: Adding input device VirtualBox mouse integration (/dev/input/js1)
[   117.759] (II) No input driver specified, ignoring this device.
[   117.759] (II) This device may have been added with another device file.
[   117.759] (II) config/udev: Adding input device VirtualBox USB Tablet (/dev/input/event1)
[   117.760] (**) VirtualBox USB Tablet: Applying InputClass "evdev pointer catchall"
[   117.760] (II) Using input driver 'evdev' for 'VirtualBox USB Tablet'
[   117.760] (**) VirtualBox USB Tablet: always reports core events
[   117.760] (**) evdev: VirtualBox USB Tablet: Device: "/dev/input/event1"
[   117.760] (--) evdev: VirtualBox USB Tablet: Vendor 0x80ee Product 0x21
[   117.760] (--) evdev: VirtualBox USB Tablet: Found 9 mouse buttons
[   117.760] (--) evdev: VirtualBox USB Tablet: Found scroll wheel(s)
[   117.760] (--) evdev: VirtualBox USB Tablet: Found relative axes
[   117.760] (--) evdev: VirtualBox USB Tablet: Found absolute axes
[   117.760] (--) evdev: VirtualBox USB Tablet: Found x and y absolute axes
[   117.760] (--) evdev: VirtualBox USB Tablet: Found absolute touchscreen
[   117.760] (II) evdev: VirtualBox USB Tablet: Configuring as touchscreen
[   117.760] (II) evdev: VirtualBox USB Tablet: Adding scrollwheel support
[   117.760] (**) evdev: VirtualBox USB Tablet: YAxisMapping: buttons 4 and 5
[   117.760] (**) evdev: VirtualBox USB Tablet: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[   117.760] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.4/usb2/2-1/2-1:1.0/input/input1/event1"
[   117.760] (II) XINPUT: Adding extended input device "VirtualBox USB Tablet" (type: TOUCHSCREEN, id 9)
[   117.760] (WW) evdev: VirtualBox USB Tablet: touchpads, tablets and touchscreens ignore relative axes.
[   117.760] (II) evdev: VirtualBox USB Tablet: initialized for absolute axes.
[   117.760] (**) VirtualBox USB Tablet: (accel) keeping acceleration scheme 1
[   117.760] (**) VirtualBox USB Tablet: (accel) acceleration profile 0
[   117.760] (**) VirtualBox USB Tablet: (accel) acceleration factor: 2.000
[   117.760] (**) VirtualBox USB Tablet: (accel) acceleration threshold: 4
[   117.760] (II) config/udev: Adding input device VirtualBox USB Tablet (/dev/input/js0)
[   117.760] (II) No input driver specified, ignoring this device.
[   117.760] (II) This device may have been added with another device file.
[   117.760] (II) config/udev: Adding input device VirtualBox USB Tablet (/dev/input/mouse0)
[   117.760] (II) No input driver specified, ignoring this device.
[   117.760] (II) This device may have been added with another device file.
[   117.760] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[   117.760] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[   117.760] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[   117.760] (**) AT Translated Set 2 keyboard: always reports core events
[   117.760] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[   117.760] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[   117.760] (--) evdev: AT Translated Set 2 keyboard: Found keys
[   117.760] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[   117.760] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[   117.761] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)
[   117.761] (**) Option "xkb_rules" "evdev"
[   117.761] (**) Option "xkb_model" "evdev"
[   117.761] (**) Option "xkb_layout" "us"
[   117.761] (II) config/udev: Adding input device ImExPS/2 Generic Explorer Mouse (/dev/input/event3)
[   117.761] (**) ImExPS/2 Generic Explorer Mouse: Applying InputClass "evdev pointer catchall"
[   117.761] (II) Using input driver 'evdev' for 'ImExPS/2 Generic Explorer Mouse'
[   117.761] (**) ImExPS/2 Generic Explorer Mouse: always reports core events
[   117.761] (**) evdev: ImExPS/2 Generic Explorer Mouse: Device: "/dev/input/event3"
[   117.761] (--) evdev: ImExPS/2 Generic Explorer Mouse: Vendor 0x2 Product 0x6
[   117.761] (--) evdev: ImExPS/2 Generic Explorer Mouse: Found 9 mouse buttons
[   117.761] (--) evdev: ImExPS/2 Generic Explorer Mouse: Found scroll wheel(s)
[   117.761] (--) evdev: ImExPS/2 Generic Explorer Mouse: Found relative axes
[   117.761] (--) evdev: ImExPS/2 Generic Explorer Mouse: Found x and y relative axes
[   117.761] (II) evdev: ImExPS/2 Generic Explorer Mouse: Configuring as mouse
[   117.761] (II) evdev: ImExPS/2 Generic Explorer Mouse: Adding scrollwheel support
[   117.761] (**) evdev: ImExPS/2 Generic Explorer Mouse: YAxisMapping: buttons 4 and 5
[   117.761] (**) evdev: ImExPS/2 Generic Explorer Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[   117.761] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input3/event3"
[   117.761] (II) XINPUT: Adding extended input device "ImExPS/2 Generic Explorer Mouse" (type: MOUSE, id 11)
[   117.761] (II) evdev: ImExPS/2 Generic Explorer Mouse: initialized for relative axes.
[   117.761] (**) ImExPS/2 Generic Explorer Mouse: (accel) keeping acceleration scheme 1
[   117.761] (**) ImExPS/2 Generic Explorer Mouse: (accel) acceleration profile 0
[   117.761] (**) ImExPS/2 Generic Explorer Mouse: (accel) acceleration factor: 2.000
[   117.761] (**) ImExPS/2 Generic Explorer Mouse: (accel) acceleration threshold: 4
[   117.761] (II) config/udev: Adding input device ImExPS/2 Generic Explorer Mouse (/dev/input/mouse1)
[   117.761] (II) No input driver specified, ignoring this device.
[   117.761] (II) This device may have been added with another device file.
[   117.761] (II) config/udev: Adding input device PC Speaker (/dev/input/event6)
[   117.761] (II) No input driver specified, ignoring this device.
[   117.761] (II) This device may have been added with another device file.
[   117.840] (II) evdev: Power Button: Close
[   117.840] (II) UnloadModule: "evdev"
[   117.843] (II) evdev: Sleep Button: Close
[   117.843] (II) UnloadModule: "evdev"
[   117.846] (II) evdev: VirtualBox mouse integration: Close
[   117.847] (II) UnloadModule: "evdev"
[   117.858] (II) evdev: VirtualBox USB Tablet: Close
[   117.858] (II) UnloadModule: "evdev"
[   117.858] (II) evdev: AT Translated Set 2 keyboard: Close
[   117.858] (II) UnloadModule: "evdev"
[   117.859] (II) evdev: ImExPS/2 Generic Explorer Mouse: Close
[   117.859] (II) UnloadModule: "evdev"
[   117.862] (II) VBoxVideo(0): [drm] removed 1 reserved context for kernel
[   117.862] (II) VBoxVideo(0): [drm] unmapping 8192 bytes of SAREA 0xe07ff000 at 0xb590b000
[   117.862] (II) VBoxVideo(0): [drm] Closed DRM master.
[   118.171] Server terminated successfully (0). Closing log file.

Last edited by graysky (2012-09-28 08:08:03)

moetunes · 2012-09-28 08:20:51

What does
pacman -Qs driver
in the vm return?

Stebalien · 2012-09-28 15:23:19

You have the required Xorg drivers and those errors appear to be expected (https://www.virtualbox.org/ticket/4789). As a matter of fact, Xorg is terminating successfully. Just to make sure, is your ~/.xinitrc setup correctly?

graysky · 2012-09-28 16:36:58

Problem isn't in my .xinitrc because even getting lxdm to load throws these errors.

graysky · 2012-09-28 19:42:47

@moetunes - Sorry, totally missed your question!

$ pacman -Qs driver
local/xf86-input-evdev 2.7.3-1 (xorg-drivers xorg)
    X.org evdev input driver

Arch Linux

#1 2012-09-28 08:02:41

Cannot load X from within a new VM.

#2 2012-09-28 08:20:51

Re: Cannot load X from within a new VM.

#3 2012-09-28 15:23:19

Re: Cannot load X from within a new VM.

#4 2012-09-28 16:36:58

Re: Cannot load X from within a new VM.

#5 2012-09-28 19:42:47

Re: Cannot load X from within a new VM.

Board footer