You are not logged in.

#1 2012-10-15 04:37:53

Arogers10
Member
Registered: 2012-06-20
Posts: 68

[Solved]Manually configure repo package

Alright so I'm trying to enable epiphany browser for use with webkit2 and every source I find online tells me to download the epiphany tar.xz package and configure it via:

./configure --with-webkit2
make
make install

and while this did work for me pacman does not recognize this manual installation. I'm wondering if there is any way to have pacman download and install the package from the official repos while also enabling the '--with-webkit' flag or something to that effect. Or if i can reconfigure the pkg.tar.xz archive and just Pacman -U it.

I have tried googling and I've gone through the wiki pages on Pacman and PKGBUILDS but have had no luck. I don't know if I'm missing something or if I'm just too tired for this right now but I really would like some help

Last edited by Arogers10 (2012-10-15 18:09:57)

Offline

#2 2012-10-15 04:42:21

WonderWoofy
Member
From: Los Gatos, CA
Registered: 2012-05-19
Posts: 8,414

Re: [Solved]Manually configure repo package

You read the page on PKGBUILDS but did not find an answer?  I am not sure I understand. 

How about you just check the AUR, last I checked there was a webkit2 PKGBUILD there.

Offline

#3 2012-10-15 04:53:30

Arogers10
Member
Registered: 2012-06-20
Posts: 68

Re: [Solved]Manually configure repo package

WonderWoofy wrote:

You read the page on PKGBUILDS but did not find an answer?  I am not sure I understand. 

How about you just check the AUR, last I checked there was a webkit2 PKGBUILD there.

I see a webkit2pdf package but that is not what I want. when you download and install from source and run './configure --with-webkit2' it goes through configuration and spits out:

Epiphany was configured with the following options:

	Source code location	   : .
	Compiler		   : gcc
	Prefix			   : /usr
	Extra debugging support	   : no
	Build tests		   : yes
	Code coverage		   : no

	GObject introspection	   : no
	NSS support		   : yes
	WebKit2			   : yes

I already have all of the packages necessary I just need to configure epiphany to use webkit2 by default for flashplugin to work properly. I just want to see if I can have pacman configure it that way upon installation

Offline

#4 2012-10-15 04:57:15

Scimmia
Fellow
Registered: 2012-09-01
Posts: 13,729

Re: [Solved]Manually configure repo package

Sure, just read up on the ABS (Arch Build System). This will get you the PKGBUILD file and associated data. You then edit the PKGBUILD to add the appropriate option and do a makepkg. Install it with pacman -U whateveritscalled.tar.xz

ETA: of course, you'll have to redo this on every update.

Last edited by Scimmia (2012-10-15 05:03:48)

Offline

#5 2012-10-15 05:01:32

Arogers10
Member
Registered: 2012-06-20
Posts: 68

Re: [Solved]Manually configure repo package

Scimmia wrote:

Sure, just read up on the ABS (Arch Build System). This will get you the PKGBUILD file and associated data. You then edit the PKGBUILD to add the appropriate option and do a makepkg. Install it with pacman -U whateveritscalled.tar.xz

Ah now that's just the wiki I needed. Thank you very much for the help smile

Offline

#6 2012-10-15 14:06:41

karol
Archivist
Registered: 2009-05-06
Posts: 25,440

Re: [Solved]Manually configure repo package

I think you can mark this thread as solved.

Offline

Board footer

Powered by FluxBB