You are not logged in.

Pages: 1

#1 2005-10-10 09:39:15

Pilli
Member
Registered: 2004-09-01
Posts: 46

Problem with ipw2100 and wpa

Hi.

I need help with my laptop and wpa wireless connection.
I try to connect but i can't, i install wpa_supplicant software and config my connection.

When i try to connect with:


wpa_supplicant -c /etc//etc/wpa_piso.conf -i eth1 -D ipw -dd

I have this output:


Initializing interface 'eth1' conf '/etc/wpa_piso.conf' driver 'ipw'
Configuration file '/etc/wpa_piso.conf' -> '/etc/wpa_piso.conf'
Reading configuration file '/etc/wpa_piso.conf'
eapol_version=1
ap_scan=1
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=10):
     43 61 6e 64 65 6c 61 72 69 61                     Candelaria
proto: 0x1
key_mgmt: 0x2
pairwise: 0x8
group: 0x8
PSK (ASCII passphrase) - hexdump_ascii(len=13): [REMOVED]
priority=2 (0x2)
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 2
   id=0 ssid='Candelaria'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw_init is called
Own MAC address: 00:0c:f1:14:2b:36
wpa_driver_ipw_set_wpa: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_countermeasures: enabled=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting scan request: 0 sec 100000 usec
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
Received 276 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 2
0: 00:c0:49:5d:4f:4e ssid='Candelaria' wpa_ie_len=24 rsn_ie_len=0
   selected
Trying to associate with 00:c0:49:5d:4f:4e (SSID='Candelaria' freq=0 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=23
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
Received 276 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 2
0: 00:c0:49:5d:4f:4e ssid='Candelaria' wpa_ie_len=24 rsn_ie_len=0
   selected
Trying to associate with 00:c0:49:5d:4f:4e (SSID='Candelaria' freq=0 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=23
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Authentication with 00:00:00:00:00:00 timed out.
BSSID 00:00:00:00:00:00 blacklist count incremented to 2
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
Received 276 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 2
0: 00:c0:49:5d:4f:4e ssid='Candelaria' wpa_ie_len=24 rsn_ie_len=0
   selected
Trying to associate with 00:c0:49:5d:4f:4e (SSID='Candelaria' freq=0 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=23
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Authentication with 00:00:00:00:00:00 timed out.
BSSID 00:00:00:00:00:00 blacklist count incremented to 3
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
Received 276 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 2
0: 00:c0:49:5d:4f:4e ssid='Candelaria' wpa_ie_len=24 rsn_ie_len=0
   selected
Trying to associate with 00:c0:49:5d:4f:4e (SSID='Candelaria' freq=0 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=23
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Signal 2 received - terminating
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw_set_wpa: enabled=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_drop_unencrypted: enabled=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_countermeasures: enabled=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
No keys have been configured - skip key clearing
Removed BSSID 00:00:00:00:00:00 from blacklist (clear)


Please, can anybody help me?

Offline

#2 2005-10-10 10:03:38

MaceM
Member
From: Austria
Registered: 2003-11-26
Posts: 47

Re: Problem with ipw2100 and wpa

i have a ipw2200 card and i need to use 

-Dwext

for wpa_supplicant to work.
-Dipw didn't work for me.

also make sure you have the latest ipw drivers, there have been some problems lately.

is your iwconfig setup correct?

Offline

#3 2005-10-10 15:38:41

Pilli
Member
Registered: 2004-09-01
Posts: 46

Re: Problem with ipw2100 and wpa

Thanks!

When i use wext driver all work perfectly.

Offline

Pages: 1

Board footer

Powered by FluxBB