You are not logged in.

#26 2005-10-11 13:49:04

tpowa
Developer
From: Lauingen , Germany
Registered: 2004-04-05
Posts: 2,262

Re: All users of ipw2200 READ!

well if you use an non arch standard kernel you are on your own wink
my package should only work flawlessly with the standard kernels.
greetings
tpowa

Offline

#27 2005-10-11 15:22:56

Michiel
Member
From: Westkapelle, Zeeland, NL
Registered: 2005-02-13
Posts: 34
Website

Re: All users of ipw2200 READ!

It works indeed, with an error...
But it's prolly ipw2200's fault

wlan0: NETDEV_TX_BUSY returned; driver should report queue full via ieee_device->is_queue_full.

All you got to do, is tell the story right...

Offline

#28 2005-10-12 06:28:48

hehejo_
Member
From: Germany
Registered: 2005-10-08
Posts: 47
Website

Re: All users of ipw2200 READ!

Good moring.
I have Problems to get ipw2200 working on my computer.
I'm using the packets from ArchLinux:

floor3: [~]
pacman -Q kernel26 ipw2200 ieee80211
kernel26 2.6.13.3-1
ipw2200 1.0.7-2
ieee80211 1.1.4-1

/etc/rc.conf

MODULES=(uhci_hcd eepro100 ipw2200 ohci1394 yenta_socket snd-intel8x0 snd-pcm-oss)
lo="lo 127.0.0.1"
eth0="eth0 192.168.1.10 netmask 255.255.255.0 broadcast 192.168.0.255"
eth1="dhcp"
INTERFACES=(lo eth0 eth1)
DAEMONS=(syslogd klogd uptimed !pcmcia network alsa !crond !xfs !hwd hotplug)

/etc/modprobe.conf

alias eth1 ipw2200

/etc/conf.d/wireless

wlan_eth1="eth1 mode auto essid HOME__jo channel 6 key xxxx"
WLAN_INTERFACES=(eth1)

This messages comes at startup and every time I try to iwconfig eth1:

root [/home/jo]
iwconfig eth1 mode auto essid HOME__jo channel 6 key xxxxx
Error for wireless request "Set Mode" (8B06) :
    SET failed on device eth1 ; Operation not supported.

This is a part of dmesg.
I think that the firmware isn't loaded.

ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, 1.1.4
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.7
ipw2200: Copyright(c) 2003-2005 Intel Corporation
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>

What's wrong? And yes, the card is on.

Offline

#29 2005-10-12 09:03:29

sml
Member
Registered: 2005-05-21
Posts: 89

Re: All users of ipw2200 READ!

I have this in my #dmesg ...

ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection

I didn't see this in yours.

Offline

#30 2005-10-12 10:27:02

hehejo_
Member
From: Germany
Registered: 2005-10-08
Posts: 47
Website

Re: All users of ipw2200 READ!

You are definitely right.
I'm gonna grep after it this afternoon.

What's wrong if my dmesg is missing this line?

Offline

#31 2005-10-12 14:48:48

hehejo_
Member
From: Germany
Registered: 2005-10-08
Posts: 47
Website

Re: All users of ipw2200 READ!

Hi, here's my grepresult.
The line is definitely not there!

floor3: [~]
dmesg | grep "ipw2200" -C 7
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
usb 1-2: new low speed USB device using uhci_hcd and address 2
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, 1.1.4
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.7
ipw2200: Copyright(c) 2003-2005 Intel Corporation
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:02:03.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11]  MMIO=[e0202000-e02027ff]  Max Packet=[2048]
ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:02:03.0 [144d:c009]
Yenta: ISA IRQ mask 0x0018, PCI irq 10
floor3: [~]

What now?

Offline

#32 2005-10-12 21:00:59

Michiel
Member
From: Westkapelle, Zeeland, NL
Registered: 2005-02-13
Posts: 34
Website

Re: All users of ipw2200 READ!

I think it can't find your ipw2200 network card..


All you got to do, is tell the story right...

Offline

#33 2005-10-13 05:23:02

hehejo_
Member
From: Germany
Registered: 2005-10-08
Posts: 47
Website

Re: All users of ipw2200 READ!

But why? Even hwd finds the card!

HARDWARE DETECT ver 4.7.1 (simple mode)
  Kernel     : 2.6.13-ARCH
  CPU & Cache: Processor 0 is Intel(R) Pentium(R) M processor 1400MHz 1395MHz, 1024 KB Cache

  ALSA(sound): Intel Corp.|ICH4 845G/GL Chipset AC'97 Audio Controller module: snd-intel8x0
/usr/bin/mkxcfg: line 123: /usr/sbin/ddcxinfo-arch: Datei oder Verzeichnis nicht gefunden
  Video      : No X
  Mouse      : Logitech Inc.|Mouse xtype: IMPS2 module: usbhid device: /dev/input/mice

  Drive(ide) : IC25N040ATMR04-0 (HD) 40010MB / 1740KB cache device: /dev/hda
  Drive(ide) : SAMSUNG CDRW/DVD SN-324F (DVDROM) 0MB  device: /dev/hdc
  Swap       : Found 498004KB device: /dev/hda2
  USB        : Intel Corp.|82801DB USB Controller module: uhci_hcd

  Ethernet   : Intel Corp.|82801BD PRO/100 VE (MOB) Ethernet Controller module: eepro100 device:   eth0
  eth1 
  Network    : Intel Corp.|PRO/Wireless LAN 2100 3B Mini PCI Adapter module: ipw2100 
  Modem      : Intel Corp.|82801DB AC module/info: slamr 
  Firewire   : Ricoh Co Ltd|R5C552 IEEE 1394 Controller module: ohci1394 
  PCMCIA slot: Ricoh Co Ltd|RL5c476 II module: yenta_socket 
  -----------:
  Menu       : Hwd: hwd, Lshwd: lshwd -?, X: mkxcfg 
  X sample   : Generate X sample: hwd -x 
  Howto      : View howto: hwd -h 

Offline

#34 2005-10-13 05:25:07

tpowa
Developer
From: Lauingen , Germany
Registered: 2004-04-05
Posts: 2,262

Re: All users of ipw2200 READ!

Network    : Intel Corp.|PRO/Wireless LAN 2100 3B Mini PCI Adapter module: ipw2100
that says 2100 not 2200
try pacman -S ipw2100
thanks
greetings
tpowa

Offline

#35 2005-10-13 06:21:55

hehejo_
Member
From: Germany
Registered: 2005-10-08
Posts: 47
Website

Re: All users of ipw2200 READ!

Thank you.  :oops:
IT'S WORKING!
*dancing*

Offline

#36 2005-10-13 14:26:45

hehejo_
Member
From: Germany
Registered: 2005-10-08
Posts: 47
Website

Re: All users of ipw2200 READ!

How can I give my wlanadapter a fixed IP like 192.168.1.11 and not an IP by dhcp in the startup?
I know
ifconfig eth1 192.168.1.11 up

Offline

#37 2005-10-24 14:22:38

Goophy
Member
Registered: 2005-09-21
Posts: 34

Re: All users of ipw2200 READ!

I'm having the exact same problems.
Full cpu use when in monitor and lots of
'ipw2200: Firmware error detected. Restarting
ipw2200: Sysfs 'error' log already exists'

Do we need a new firmware or something?

Offline

#38 2006-04-06 03:32:31

prokrypt
Member
Registered: 2006-04-06
Posts: 4

Re: All users of ipw2200 READ!

I recently upgraded my kernel + ipw2200 firmware (pacman -Syu) and I noticed that monitor mode works without firmware errors/100% cpu usage anymore! w00t =]
---
Linux PKLaptop 2.6.16-ARCH #1 SMP PREEMPT Mon Apr 3 16:07:44 CEST 2006 i686 Intel(R) Pentium(R) M processor 1.86GHz GenuineIntel GNU/Linux
Firmware: ipw2200 1.1.1-2

Offline

#39 2006-04-09 10:52:19

Sigi
Member
From: Thurgau, Switzerland
Registered: 2005-09-22
Posts: 1,121

Re: All users of ipw2200 READ!

I just started to read the whole thread on this topic until I realised that it was 6 month old..  big_smile  Nice to see it (also) work for you!


Dammit, haven't been here in a while. Still rocking Arch. smile

Offline

Board footer

Powered by FluxBB