You are not logged in.

#1 2012-11-03 19:24:53

KejPi
Member
Registered: 2011-06-17
Posts: 40

KDE4 randr + Samsung TV HDMI [SOLVED]

Hello, I have following HW config:

HP laptop with  Radeon HD 6370 with HDMI output
Samsung LED TV UE46c6500, native resolution 1920x1080
Laptop display resolution is 1600x900

When I connect laptop with  TV using HDMI cable and message saying "new monitor connected " appears. Then I can configure new monitor. So far so good. I  can select  native resolution of TV and I can see a KDE desktop on TV. But this  desktop is cropped. On each side some pixels are missing.I If I align resolution of laptop and TV, desktop is fine, nothing is missing but  sound over HDMI stops working.

I want to use TV for XBMC and neither missing information  nor missing sound is not  acceptable for that.

Questions:
1) how to fix missing part of desktop with native TV's resolution (preferred) or at least audio with different resolution?
2) is there any better plug-play solution for XBMC? I mean I want to connect laptop to TV only when I want to watch movies. It will not be used exclusively for that and I do not want to spend 10 minutes each time I want to run XBMC and then another time to switch back to standard operation.

Thanks!

Last edited by KejPi (2012-11-04 18:44:49)

Offline

#2 2012-11-03 23:18:54

masteryod
Member
Registered: 2010-05-19
Posts: 433

Re: KDE4 randr + Samsung TV HDMI [SOLVED]

I'm afraid I'm not understanding this to much but there's a thing or two:
1) you probably want to make your TV as a second extended display (in matter of fact the bullet-proof solution is to switch to TV entirely and switch-off laptop display: make your TV main and only display, this way you won't get hassle with multi-display bugs e.g tearing, main/secondary full sreen issues etc.) I'm afraid that cloning with different resolutions might not work.
2) go and check your HDMI's on back of your TV and look for "PC" signed one, Samsung actually did that on my TV and on HDMI-1 I was unable to set up native resolution, on HDMI-2 which was made as a PC input - everything worked out-of-box
3) I know nothing about audio through HDMI on Linux

About question number 2:
- you mean something like script that will detect hdmi cable, switch your displays and run XBMC? That's probably doable but as soon as you set-up your TV correctly changing display shouldn't take more time than 15s. Just leave a HDMI cable plugged to your TV all the time, go with a laptop whenever you need it, plug HDMI to your laptop, click inside KDE like 2 or 3 times and that's all (you can send krandr icon to tray too so you won't be looking at systemsetting all the time)

Offline

#3 2012-11-04 18:26:19

KejPi
Member
Registered: 2011-06-17
Posts: 40

Re: KDE4 randr + Samsung TV HDMI [SOLVED]

Thank you for your hints. I have tried to run XBMC on TV connected as the only display and yes, it solved some issues. But the main problem still persists:
How to use TV with native resolution 1920x1080? According to your hint I have tried another HDMI input (previously tested with HDMI3 through AV receiver and HDMI4 direct connection from laptop - the same resiult in both cases) - HDMI1 is marked as HDMI/DVI - so I have tried with this but unfortunately with the same result. For native TV resolution the desktop is cropped. I have switched to lower resolution and then desktop fits.

EDIT: I am sorry, my mistake. The problem was in TV setup, where 16:9 mode was forced that caused somehow cropping of image. Marking thread solved, thank you for help.

Last edited by KejPi (2012-11-04 18:44:30)

Offline

#4 2012-11-04 20:52:19

masteryod
Member
Registered: 2010-05-19
Posts: 433

Re: KDE4 randr + Samsung TV HDMI [SOLVED]

Ah, yeas it was called "HDMI/DVI" not "PC". I'm glad you've solved your problem.

Offline

Board footer

Powered by FluxBB