You are not logged in.
Pages: 1
Hi,
I’m trying to use Arch on my new machine. It’s a basically an Intel Core i7-3770 an Intel DZ77BH-55K motherboard.
I tried installing with the latest install media (2013.01.04), but I could not even boot with it: as soon as the kernel loads, the computers reboots. I then used Archboot 2012.10: the 3.6.2 has the same problem, but the LTS (3.0.46) boots fine, so I installed with it.
So as of now, it runs on the LTS kernel (3.0.60), but I have many troubles with graphics (small KMS console, video tearing, X freeze, reboot, etc.), and I thought using a more recent kernel would help (I have already read the wiki on Intel Graphics, and other posts).
If I remove i915 from mkinitcpio.conf and comment the line in /etc/modprobe.d/modprobe.conf, the 3.7.4 kernel can boot, but only for a few seconds and the reboots (I think it’s when the i915 module is loaded).
Any help appreciated, thanks
Packages:
linux 3.7.4-1
linux-ck 3.7.4-1
linux-lts 3.0.60-1
intel-dri 9.0.2-1
intel-gpu-tools 1.3-2
intel-ucode 20120606_v2-1
libva-intel-driver 1.0.19-1
xf86-video-intel 2.20.19-1
# lspci
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller (rev 09)
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04)
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
00:1c.2 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 (rev c4)
00:1c.4 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 5 (rev c4)
00:1c.7 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 8 (rev c4)
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation Z77 Express Chipset LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 7 Series/C210 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
02:00.0 PCI bridge: Integrated Technology Express, Inc. Device 8892 (rev 30)
03:02.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22A IEEE-1394a-2000 Controller (PHY/Link) [iOHCI-Lynx]
04:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
05:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller (rev 11)
# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.60-1-lts (tobias@T-POWA-LX) (gcc version 4.7.2 (GCC) ) #1 SMP Mon Jan 21 22:58:04 CET 2013
[ 0.000000] Command line: initrd=/initramfs-linux-lts.img root=LABEL=Polymnie rootflags=,relatime,user_xattr,barrier=1,data=ordered rootfstype=ext4 ro BOOT_IMAGE=/vmlinuz-linux-lts
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
[ 0.000000] BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
[ 0.000000] BIOS-e820: 0000000020000000 - 0000000020200000 (reserved)
[ 0.000000] BIOS-e820: 0000000020200000 - 0000000040004000 (usable)
[ 0.000000] BIOS-e820: 0000000040004000 - 0000000040005000 (reserved)
[ 0.000000] BIOS-e820: 0000000040005000 - 00000000d9b29000 (usable)
[ 0.000000] BIOS-e820: 00000000d9b29000 - 00000000da278000 (reserved)
[ 0.000000] BIOS-e820: 00000000da278000 - 00000000da288000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000da288000 - 00000000da399000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000da399000 - 00000000da68b000 (reserved)
[ 0.000000] BIOS-e820: 00000000da68b000 - 00000000da68c000 (usable)
[ 0.000000] BIOS-e820: 00000000da68c000 - 00000000da6cf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000da6cf000 - 00000000db000000 (usable)
[ 0.000000] BIOS-e820: 00000000db800000 - 00000000dfa00000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed04000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000041f600000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.7 present.
[ 0.000000] DMI: /DZ77BH-55K, BIOS BHZ7710H.86A.0097.2012.1228.1346 12/28/2012
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x41f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask C00000000 write-back
[ 0.000000] 1 base 400000000 mask FE0000000 write-back
[ 0.000000] 2 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 3 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 4 base 0DB800000 mask FFF800000 uncachable
[ 0.000000] 5 base 41F800000 mask FFF800000 uncachable
[ 0.000000] 6 base 41F600000 mask FFFE00000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000db800000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xdb000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000fd830] fd830
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-00000000db000000
[ 0.000000] 0000000000 - 00db000000 page 2M
[ 0.000000] kernel direct mapping tables up to 0xdaffffff @ [mem 0x1fd6f000-0x1fd73fff]
[ 0.000000] init_memory_mapping: 0000000100000000-000000041f600000
[ 0.000000] 0100000000 - 041f600000 page 2M
[ 0.000000] kernel direct mapping tables up to 0x41f5fffff @ [mem 0xdaff2000-0xdaffffff]
[ 0.000000] RAMDISK: 1fd74000 - 1ffff000
[ 0.000000] ACPI: RSDP 00000000000f0490 00024 (v02 INTEL)
[ 0.000000] ACPI: XSDT 00000000da27c078 0006C (v01 INTEL DZ77BH 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 00000000da285e38 0010C (v05 INTEL DZ77BH 01072009 AMI 00010013)
[ 0.000000] ACPI Warning: FADT (revision 5) is longer than ACPI 2.0 version, truncating length 268 to 244 (20110413/tbfadt-288)
[ 0.000000] ACPI: DSDT 00000000da27c170 09CC7 (v02 INTEL DZ77BH 00000097 INTL 20051117)
[ 0.000000] ACPI: FACS 00000000da397080 00040
[ 0.000000] ACPI: APIC 00000000da285f48 00092 (v03 INTEL DZ77BH 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 00000000da285fe0 00044 (v01 INTEL DZ77BH 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 00000000da286028 0003C (v01 INTEL DZ77BH 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000da286068 00038 (v01 INTEL DZ77BH 01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 00000000da2860a0 0036D (v01 SataRe SataTabl 00001000 INTL 20091112)
[ 0.000000] ACPI: SSDT 00000000da286410 009AA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 00000000da286dc0 00A92 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: DMAR 00000000da287858 000B8 (v01 INTEL SNB 00000001 INTL 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000041f600000
[ 0.000000] Initmem setup node 0 0000000000000000-000000041f600000
[ 0.000000] NODE_DATA [000000041f5fb000 - 000000041f5fffff]
[ 0.000000] [ffffea0000000000-ffffea000e7fffff] PMD -> [ffff88040ec00000-ffff88041cdfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x0041f600
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[7] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009d
[ 0.000000] 0: 0x00000100 -> 0x00020000
[ 0.000000] 0: 0x00020200 -> 0x00040004
[ 0.000000] 0: 0x00040005 -> 0x000d9b29
[ 0.000000] 0: 0x000da68b -> 0x000da68c
[ 0.000000] 0: 0x000da6cf -> 0x000db000
[ 0.000000] 0: 0x00100000 -> 0x0041f600
[ 0.000000] On node 0 totalpages: 4167655
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3920 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 875154 pages, LIFO batch:31
[ 0.000000] Normal zone: 44765 pages used for memmap
[ 0.000000] Normal zone: 3229475 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[ 0.000000] PM: Registered nosave memory: 0000000040004000 - 0000000040005000
[ 0.000000] PM: Registered nosave memory: 00000000d9b29000 - 00000000da278000
[ 0.000000] PM: Registered nosave memory: 00000000da278000 - 00000000da288000
[ 0.000000] PM: Registered nosave memory: 00000000da288000 - 00000000da399000
[ 0.000000] PM: Registered nosave memory: 00000000da399000 - 00000000da68b000
[ 0.000000] PM: Registered nosave memory: 00000000da68c000 - 00000000da6cf000
[ 0.000000] PM: Registered nosave memory: 00000000db000000 - 00000000db800000
[ 0.000000] PM: Registered nosave memory: 00000000db800000 - 00000000dfa00000
[ 0.000000] PM: Registered nosave memory: 00000000dfa00000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[ 0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed00000
[ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed04000
[ 0.000000] PM: Registered nosave memory: 00000000fed04000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
[ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at dfa00000 (gap: dfa00000:18600000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88041f200000 s79360 r8192 d23040 u262144
[ 0.000000] pcpu-alloc: s79360 r8192 d23040 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 4108549
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: initrd=/initramfs-linux-lts.img root=LABEL=Polymnie rootflags=,relatime,user_xattr,barrier=1,data=ordered rootfstype=ext4 ro BOOT_IMAGE=/vmlinuz-linux-lts
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 16357800k/17291264k available (4268k kernel code, 620644k absent, 312820k reserved, 5179k data, 740k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:2304
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 134217728 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.010000] Detected 3391.975 MHz processor.
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 6783.95 BogoMIPS (lpj=33919750)
[ 0.000004] pid_max: default: 32768 minimum: 301
[ 0.000114] Security Framework initialized
[ 0.000119] AppArmor: AppArmor disabled by boot time parameter
[ 0.000776] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.003657] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.004934] Mount-cache hash table entries: 256
[ 0.005193] Initializing cgroup subsys cpuacct
[ 0.005220] Initializing cgroup subsys memory
[ 0.005240] Initializing cgroup subsys devices
[ 0.005241] Initializing cgroup subsys freezer
[ 0.005242] Initializing cgroup subsys net_cls
[ 0.005243] Initializing cgroup subsys blkio
[ 0.005283] CPU: Physical Processor ID: 0
[ 0.005284] CPU: Processor Core ID: 0
[ 0.005288] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.005288] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.005550] mce: CPU supports 9 MCE banks
[ 0.005560] CPU0: Thermal monitoring enabled (TM1)
[ 0.005567] using mwait in idle threads.
[ 0.006329] ACPI: Core revision 20110413
[ 0.022944] ftrace: allocating 16891 entries in 67 pages
[ 0.026832] DMAR: Host address width 36
[ 0.026834] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[ 0.026839] IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c0000020e60262 ecap f0101a
[ 0.026840] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[ 0.026844] IOMMU 1: reg_base_addr fed91000 ver 1:0 cap c9008020660262 ecap f0105a
[ 0.026845] DMAR: RMRR base: 0x000000da20f000 end: 0x000000da21bfff
[ 0.026846] DMAR: RMRR base: 0x000000db800000 end: 0x000000df9fffff
[ 0.026847] DMAR: No ATSR found
[ 0.026945] Not enabling x2apic, Intr-remapping init failed.
[ 0.027287] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.126998] CPU0: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz stepping 09
[ 0.237702] Performance Events: PEBS fmt1+, generic architected perfmon, Intel PMU driver.
[ 0.237705] ... version: 3
[ 0.237706] ... bit width: 48
[ 0.237707] ... generic registers: 4
[ 0.237707] ... value mask: 0000ffffffffffff
[ 0.237708] ... max period: 000000007fffffff
[ 0.237709] ... fixed-purpose events: 3
[ 0.237710] ... event mask: 000000070000000f
[ 0.237963] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.238006] Booting Node 0, Processors #1
[ 0.238008] smpboot cpu 1: start_ip = 98000
[ 0.417504] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.417560] #2
[ 0.417561] smpboot cpu 2: start_ip = 98000
[ 0.597054] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.597105] #3
[ 0.597106] smpboot cpu 3: start_ip = 98000
[ 0.776498] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.776549] #4
[ 0.776549] smpboot cpu 4: start_ip = 98000
[ 0.955970] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.956032] #5
[ 0.956032] smpboot cpu 5: start_ip = 98000
[ 1.135527] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.135580] #6
[ 1.135581] smpboot cpu 6: start_ip = 98000
[ 1.314973] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.315025] #7 Ok.
[ 1.315026] smpboot cpu 7: start_ip = 98000
[ 1.494520] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.494541] Brought up 8 CPUs
[ 1.494543] Total of 8 processors activated (54276.01 BogoMIPS).
[ 1.499203] devtmpfs: initialized
[ 1.500056] PM: Registering ACPI NVS region at da288000 (1118208 bytes)
[ 1.500067] PM: Registering ACPI NVS region at da68c000 (274432 bytes)
[ 1.500594] NET: Registered protocol family 16
[ 1.500698] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 1.500699] ACPI: bus type pci registered
[ 1.500879] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 1.500881] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 1.510782] PCI: Using configuration type 1 for base access
[ 1.511222] bio: create slab <bio-0> at 0
[ 1.512191] ACPI: EC: Look up EC in DSDT
[ 1.513121] ACPI: Executed 1 blocks of module-level executable AML code
[ 1.544240] ACPI: SSDT 00000000da224018 0083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 1.544462] ACPI: Dynamic OEM Table Load:
[ 1.544463] ACPI: SSDT (null) 0083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 1.574038] ACPI: SSDT 00000000da225a98 00303 (v01 PmRef ApIst 00003000 INTL 20051117)
[ 1.574275] ACPI: Dynamic OEM Table Load:
[ 1.574276] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20051117)
[ 1.603874] ACPI: SSDT 00000000da226c18 00119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 1.604089] ACPI: Dynamic OEM Table Load:
[ 1.604090] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 1.634396] ACPI: Interpreter enabled
[ 1.634398] ACPI: (supports S0 S3 S4 S5)
[ 1.634411] ACPI: Using IOAPIC for interrupt routing
[ 1.638004] ACPI: Power Resource [FN00] (off)
[ 1.638049] ACPI: Power Resource [FN01] (off)
[ 1.638093] ACPI: Power Resource [FN02] (off)
[ 1.638137] ACPI: Power Resource [FN03] (off)
[ 1.638179] ACPI: Power Resource [FN04] (off)
[ 1.638440] ACPI: No dock devices found.
[ 1.638441] HEST: Table not found.
[ 1.638442] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.638624] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 1.638888] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 1.638890] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 1.638891] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 1.638893] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
[ 1.638894] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
[ 1.638895] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
[ 1.638896] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
[ 1.638898] pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
[ 1.638899] pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
[ 1.638900] pci_root PNP0A08:00: host bridge window [mem 0xdfa00000-0xfeafffff]
[ 1.638908] pci 0000:00:00.0: [8086:0150] type 0 class 0x000600
[ 1.638934] pci 0000:00:02.0: [8086:0162] type 0 class 0x000300
[ 1.638941] pci 0000:00:02.0: reg 10: [mem 0xf7800000-0xf7bfffff 64bit]
[ 1.638945] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 1.638948] pci 0000:00:02.0: reg 20: [io 0xf000-0xf03f]
[ 1.638989] pci 0000:00:14.0: [8086:1e31] type 0 class 0x000c03
[ 1.639009] pci 0000:00:14.0: reg 10: [mem 0xf7f20000-0xf7f2ffff 64bit]
[ 1.639075] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 1.639079] pci 0000:00:14.0: PME# disabled
[ 1.639097] pci 0000:00:16.0: [8086:1e3a] type 0 class 0x000780
[ 1.639118] pci 0000:00:16.0: reg 10: [mem 0xf7f3b000-0xf7f3b00f 64bit]
[ 1.639187] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 1.639191] pci 0000:00:16.0: PME# disabled
[ 1.639216] pci 0000:00:19.0: [8086:1503] type 0 class 0x000200
[ 1.639233] pci 0000:00:19.0: reg 10: [mem 0xf7f00000-0xf7f1ffff]
[ 1.639240] pci 0000:00:19.0: reg 14: [mem 0xf7f39000-0xf7f39fff]
[ 1.639249] pci 0000:00:19.0: reg 18: [io 0xf080-0xf09f]
[ 1.639307] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 1.639310] pci 0000:00:19.0: PME# disabled
[ 1.639331] pci 0000:00:1a.0: [8086:1e2d] type 0 class 0x000c03
[ 1.639350] pci 0000:00:1a.0: reg 10: [mem 0xf7f38000-0xf7f383ff]
[ 1.639434] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 1.639437] pci 0000:00:1a.0: PME# disabled
[ 1.639457] pci 0000:00:1b.0: [8086:1e20] type 0 class 0x000403
[ 1.639471] pci 0000:00:1b.0: reg 10: [mem 0xf7f30000-0xf7f33fff 64bit]
[ 1.639532] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 1.639535] pci 0000:00:1b.0: PME# disabled
[ 1.639552] pci 0000:00:1c.0: [8086:1e10] type 1 class 0x000604
[ 1.639625] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.639629] pci 0000:00:1c.0: PME# disabled
[ 1.639651] pci 0000:00:1c.2: [8086:1e14] type 1 class 0x000604
[ 1.639723] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 1.639726] pci 0000:00:1c.2: PME# disabled
[ 1.639746] pci 0000:00:1c.4: [8086:1e18] type 1 class 0x000604
[ 1.639818] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 1.639822] pci 0000:00:1c.4: PME# disabled
[ 1.639844] pci 0000:00:1c.7: [8086:1e1e] type 1 class 0x000604
[ 1.639916] pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
[ 1.639920] pci 0000:00:1c.7: PME# disabled
[ 1.639944] pci 0000:00:1d.0: [8086:1e26] type 0 class 0x000c03
[ 1.639964] pci 0000:00:1d.0: reg 10: [mem 0xf7f37000-0xf7f373ff]
[ 1.640047] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 1.640050] pci 0000:00:1d.0: PME# disabled
[ 1.640071] pci 0000:00:1f.0: [8086:1e44] type 0 class 0x000601
[ 1.640185] pci 0000:00:1f.2: [8086:1e02] type 0 class 0x000106
[ 1.640202] pci 0000:00:1f.2: reg 10: [io 0xf0d0-0xf0d7]
[ 1.640209] pci 0000:00:1f.2: reg 14: [io 0xf0c0-0xf0c3]
[ 1.640217] pci 0000:00:1f.2: reg 18: [io 0xf0b0-0xf0b7]
[ 1.640224] pci 0000:00:1f.2: reg 1c: [io 0xf0a0-0xf0a3]
[ 1.640231] pci 0000:00:1f.2: reg 20: [io 0xf060-0xf07f]
[ 1.640238] pci 0000:00:1f.2: reg 24: [mem 0xf7f36000-0xf7f367ff]
[ 1.640279] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.640282] pci 0000:00:1f.2: PME# disabled
[ 1.640295] pci 0000:00:1f.3: [8086:1e22] type 0 class 0x000c05
[ 1.640309] pci 0000:00:1f.3: reg 10: [mem 0xf7f35000-0xf7f350ff 64bit]
[ 1.640328] pci 0000:00:1f.3: reg 20: [io 0xf040-0xf05f]
[ 1.640392] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 1.640395] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
[ 1.640399] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 1.640405] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 1.640472] pci 0000:02:00.0: [1283:8892] type 1 class 0x000604
[ 1.640661] pci 0000:02:00.0: supports D1 D2
[ 1.640662] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.640670] pci 0000:02:00.0: PME# disabled
[ 1.640694] pci 0000:00:1c.2: PCI bridge to [bus 02-03]
[ 1.640698] pci 0000:00:1c.2: bridge window [io 0xf000-0x0000] (disabled)
[ 1.640702] pci 0000:00:1c.2: bridge window [mem 0xf7e00000-0xf7efffff]
[ 1.640707] pci 0000:00:1c.2: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 1.640821] pci 0000:03:02.0: [104c:8023] type 0 class 0x000c00
[ 1.640866] pci 0000:03:02.0: reg 10: [mem 0xf7e04000-0xf7e047ff]
[ 1.640890] pci 0000:03:02.0: reg 14: [mem 0xf7e00000-0xf7e03fff]
[ 1.641075] pci 0000:03:02.0: supports D1 D2
[ 1.641076] pci 0000:03:02.0: PME# supported from D0 D1 D2 D3hot
[ 1.641083] pci 0000:03:02.0: PME# disabled
[ 1.641186] pci 0000:02:00.0: PCI bridge to [bus 03-03] (subtractive decode)
[ 1.641200] pci 0000:02:00.0: bridge window [io 0xfff000-0x0000] (disabled)
[ 1.641208] pci 0000:02:00.0: bridge window [mem 0xf7e00000-0xf7efffff]
[ 1.641221] pci 0000:02:00.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 1.641223] pci 0000:02:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
[ 1.641224] pci 0000:02:00.0: bridge window [mem 0xf7e00000-0xf7efffff] (subtractive decode)
[ 1.641226] pci 0000:02:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
[ 1.641227] pci 0000:02:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
[ 1.641323] pci 0000:04:00.0: [1033:0194] type 0 class 0x000c03
[ 1.641366] pci 0000:04:00.0: reg 10: [mem 0xf7d00000-0xf7d01fff 64bit]
[ 1.641535] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[ 1.641542] pci 0000:04:00.0: PME# disabled
[ 1.653678] pci 0000:00:1c.4: PCI bridge to [bus 04-04]
[ 1.653683] pci 0000:00:1c.4: bridge window [io 0xf000-0x0000] (disabled)
[ 1.653698] pci 0000:00:1c.4: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 1.653703] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 1.653765] pci 0000:05:00.0: [1b4b:9172] type 0 class 0x000106
[ 1.653784] pci 0000:05:00.0: reg 10: [io 0xe040-0xe047]
[ 1.653797] pci 0000:05:00.0: reg 14: [io 0xe030-0xe033]
[ 1.653811] pci 0000:05:00.0: reg 18: [io 0xe020-0xe027]
[ 1.653825] pci 0000:05:00.0: reg 1c: [io 0xe010-0xe013]
[ 1.653838] pci 0000:05:00.0: reg 20: [io 0xe000-0xe00f]
[ 1.653852] pci 0000:05:00.0: reg 24: [mem 0xf7c20000-0xf7c201ff]
[ 1.653866] pci 0000:05:00.0: reg 30: [mem 0xf7c00000-0xf7c1ffff pref]
[ 1.653931] pci 0000:05:00.0: PME# supported from D3hot
[ 1.653936] pci 0000:05:00.0: PME# disabled
[ 1.673610] pci 0000:00:1c.7: PCI bridge to [bus 05-05]
[ 1.673615] pci 0000:00:1c.7: bridge window [io 0xe000-0xefff]
[ 1.673621] pci 0000:00:1c.7: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 1.673628] pci 0000:00:1c.7: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 1.673658] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.673727] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 1.673746] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 1.673764] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03.ITEE._PRT]
[ 1.673790] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 1.673809] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP08._PRT]
[ 1.673888] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 1.674003] pci0000:00: ACPI _OSC control (0x18) granted
[ 1.676548] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.676576] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 1.676603] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 1.676629] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 1.676654] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 1.676680] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 1.676707] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.676733] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 1.676775] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.676779] vgaarb: loaded
[ 1.676780] vgaarb: bridge control possible 0000:00:02.0
[ 1.676803] PCI: Using ACPI for IRQ routing
[ 1.678182] PCI: pci_cache_line_size set to 64 bytes
[ 1.678248] reserve RAM buffer: 000000000009d400 - 000000000009ffff
[ 1.678249] reserve RAM buffer: 0000000040004000 - 0000000043ffffff
[ 1.678250] reserve RAM buffer: 00000000d9b29000 - 00000000dbffffff
[ 1.678252] reserve RAM buffer: 00000000da68c000 - 00000000dbffffff
[ 1.678253] reserve RAM buffer: 00000000db000000 - 00000000dbffffff
[ 1.678255] reserve RAM buffer: 000000041f600000 - 000000041fffffff
[ 1.678323] NetLabel: Initializing
[ 1.678324] NetLabel: domain hash size = 128
[ 1.678325] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.678332] NetLabel: unlabeled traffic allowed by default
[ 1.678341] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 1.678344] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 1.680349] Switching to clocksource hpet
[ 1.683346] pnp: PnP ACPI init
[ 1.683353] ACPI: bus type pnp registered
[ 1.683505] pnp 00:00: [bus 00-3e]
[ 1.683507] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 1.683508] pnp 00:00: [io 0x0cf8-0x0cff]
[ 1.683509] pnp 00:00: [io 0x0d00-0xffff window]
[ 1.683510] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 1.683511] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 1.683512] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 1.683513] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 1.683514] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 1.683516] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 1.683517] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 1.683518] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 1.683519] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 1.683520] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 1.683521] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 1.683522] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 1.683523] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 1.683524] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 1.683525] pnp 00:00: [mem 0xdfa00000-0xfeafffff window]
[ 1.683527] pnp 00:00: [mem 0x00010000-0x0001ffff window]
[ 1.683558] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 1.683568] Switched to NOHz mode on CPU #0
[ 1.683573] pnp 00:01: [mem 0xfed40000-0xfed44fff]
[ 1.683594] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
[ 1.683596] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 1.683602] pnp 00:02: [io 0x0000-0x001f]
[ 1.683604] pnp 00:02: [io 0x0081-0x0091]
[ 1.683604] pnp 00:02: [io 0x0093-0x009f]
[ 1.683605] pnp 00:02: [io 0x00c0-0x00df]
[ 1.683607] pnp 00:02: [dma 4]
[ 1.683617] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 1.683621] pnp 00:03: [mem 0xff000000-0xffffffff]
[ 1.683631] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.683676] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 1.683688] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.683694] pnp 00:05: [io 0x002e-0x002f]
[ 1.683695] pnp 00:05: [io 0x004e-0x004f]
[ 1.683696] pnp 00:05: [io 0x0061]
[ 1.683697] pnp 00:05: [io 0x0063]
[ 1.683698] pnp 00:05: [io 0x0065]
[ 1.683699] pnp 00:05: [io 0x0067]
[ 1.683699] pnp 00:05: [io 0x0070]
[ 1.683700] pnp 00:05: [io 0x0080]
[ 1.683701] pnp 00:05: [io 0x0092]
[ 1.683703] pnp 00:05: [io 0x00b2-0x00b3]
[ 1.683704] pnp 00:05: [io 0x0680-0x069f]
[ 1.683705] pnp 00:05: [io 0x1000-0x100f]
[ 1.683706] pnp 00:05: [io 0xffff]
[ 1.683707] pnp 00:05: [io 0xffff]
[ 1.683707] pnp 00:05: [io 0x0400-0x0453]
[ 1.683708] pnp 00:05: [io 0x0458-0x047f]
[ 1.683709] pnp 00:05: [io 0x0500-0x057f]
[ 1.683710] pnp 00:05: [io 0x164e-0x164f]
[ 1.683731] system 00:05: [io 0x0680-0x069f] has been reserved
[ 1.683733] system 00:05: [io 0x1000-0x100f] has been reserved
[ 1.683734] system 00:05: [io 0xffff] has been reserved
[ 1.683735] system 00:05: [io 0xffff] has been reserved
[ 1.683736] system 00:05: [io 0x0400-0x0453] has been reserved
[ 1.683738] system 00:05: [io 0x0458-0x047f] has been reserved
[ 1.683739] system 00:05: [io 0x0500-0x057f] has been reserved
[ 1.683740] system 00:05: [io 0x164e-0x164f] has been reserved
[ 1.683742] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.683746] pnp 00:06: [io 0x0070-0x0077]
[ 1.683752] pnp 00:06: [irq 8]
[ 1.683762] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.683778] pnp 00:07: [io 0x0454-0x0457]
[ 1.683795] system 00:07: [io 0x0454-0x0457] has been reserved
[ 1.683797] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 1.683827] pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
[ 1.683828] pnp 00:08: [io 0x0a00-0x0a0f]
[ 1.683829] pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
[ 1.683850] system 00:08: [io 0x0a00-0x0a0f] has been reserved
[ 1.683852] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.683877] Switched to NOHz mode on CPU #1
[ 1.683886] Switched to NOHz mode on CPU #4
[ 1.683905] Switched to NOHz mode on CPU #3
[ 1.683919] Switched to NOHz mode on CPU #6
[ 1.683940] Switched to NOHz mode on CPU #2
[ 1.683956] Switched to NOHz mode on CPU #5
[ 1.683978] Switched to NOHz mode on CPU #7
[ 1.684031] pnp 00:09: [io 0x03f8-0x03ff]
[ 1.684035] pnp 00:09: [irq 4]
[ 1.684036] pnp 00:09: [dma 0 disabled]
[ 1.684065] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.684118] pnp 00:0a: [io 0x0010-0x001f]
[ 1.684119] pnp 00:0a: [io 0x0022-0x003f]
[ 1.684120] pnp 00:0a: [io 0x0044-0x005f]
[ 1.684121] pnp 00:0a: [io 0x0062-0x0063]
[ 1.684122] pnp 00:0a: [io 0x0065-0x006f]
[ 1.684122] pnp 00:0a: [io 0x0072-0x007f]
[ 1.684123] pnp 00:0a: [io 0x0080]
[ 1.684124] pnp 00:0a: [io 0x0084-0x0086]
[ 1.684125] pnp 00:0a: [io 0x0088]
[ 1.684126] pnp 00:0a: [io 0x008c-0x008e]
[ 1.684127] pnp 00:0a: [io 0x0090-0x009f]
[ 1.684128] pnp 00:0a: [io 0x00a2-0x00bf]
[ 1.684129] pnp 00:0a: [io 0x00e0-0x00ef]
[ 1.684130] pnp 00:0a: [io 0x04d0-0x04d1]
[ 1.684151] system 00:0a: [io 0x04d0-0x04d1] has been reserved
[ 1.684152] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.684158] pnp 00:0b: [io 0x00f0-0x00ff]
[ 1.684162] pnp 00:0b: [irq 13]
[ 1.684173] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 1.684293] pnp 00:0c: [mem 0xfed1c000-0xfed1ffff]
[ 1.684294] pnp 00:0c: [mem 0xfed10000-0xfed17fff]
[ 1.684295] pnp 00:0c: [mem 0xfed18000-0xfed18fff]
[ 1.684296] pnp 00:0c: [mem 0xfed19000-0xfed19fff]
[ 1.684297] pnp 00:0c: [mem 0xf8000000-0xfbffffff]
[ 1.684298] pnp 00:0c: [mem 0xfed20000-0xfed3ffff]
[ 1.684299] pnp 00:0c: [mem 0xfed90000-0xfed93fff]
[ 1.684300] pnp 00:0c: [mem 0xfed45000-0xfed8ffff]
[ 1.684301] pnp 00:0c: [mem 0xff000000-0xffffffff]
[ 1.684302] pnp 00:0c: [mem 0xfee00000-0xfeefffff]
[ 1.684303] pnp 00:0c: [mem 0xdfa00000-0xdfa00fff]
[ 1.684336] system 00:0c: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 1.684337] system 00:0c: [mem 0xfed10000-0xfed17fff] has been reserved
[ 1.684339] system 00:0c: [mem 0xfed18000-0xfed18fff] has been reserved
[ 1.684340] system 00:0c: [mem 0xfed19000-0xfed19fff] has been reserved
[ 1.684342] system 00:0c: [mem 0xf8000000-0xfbffffff] has been reserved
[ 1.684343] system 00:0c: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 1.684344] system 00:0c: [mem 0xfed90000-0xfed93fff] has been reserved
[ 1.684346] system 00:0c: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 1.684347] system 00:0c: [mem 0xff000000-0xffffffff] has been reserved
[ 1.684348] system 00:0c: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 1.684350] system 00:0c: [mem 0xdfa00000-0xdfa00fff] has been reserved
[ 1.684351] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.684429] pnp 00:0d: [mem 0x20000000-0x201fffff]
[ 1.684430] pnp 00:0d: [mem 0x40004000-0x40004fff]
[ 1.684460] system 00:0d: [mem 0x20000000-0x201fffff] has been reserved
[ 1.684462] system 00:0d: [mem 0x40004000-0x40004fff] has been reserved
[ 1.684463] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 1.684475] pnp: PnP ACPI: found 14 devices
[ 1.684476] ACPI: ACPI bus type pnp unregistered
[ 1.689698] PCI: max bus depth: 2 pci_try_num: 3
[ 1.689747] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 1.689748] pci 0000:00:1c.0: bridge window [io disabled]
[ 1.689752] pci 0000:00:1c.0: bridge window [mem disabled]
[ 1.689756] pci 0000:00:1c.0: bridge window [mem pref disabled]
[ 1.689762] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[ 1.689763] pci 0000:02:00.0: bridge window [io disabled]
[ 1.689773] pci 0000:02:00.0: bridge window [mem 0xf7e00000-0xf7efffff]
[ 1.689781] pci 0000:02:00.0: bridge window [mem pref disabled]
[ 1.689791] pci 0000:00:1c.2: PCI bridge to [bus 02-03]
[ 1.689792] pci 0000:00:1c.2: bridge window [io disabled]
[ 1.689797] pci 0000:00:1c.2: bridge window [mem 0xf7e00000-0xf7efffff]
[ 1.689801] pci 0000:00:1c.2: bridge window [mem pref disabled]
[ 1.689806] pci 0000:00:1c.4: PCI bridge to [bus 04-04]
[ 1.689807] pci 0000:00:1c.4: bridge window [io disabled]
[ 1.689812] pci 0000:00:1c.4: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 1.689815] pci 0000:00:1c.4: bridge window [mem pref disabled]
[ 1.689821] pci 0000:00:1c.7: PCI bridge to [bus 05-05]
[ 1.689823] pci 0000:00:1c.7: bridge window [io 0xe000-0xefff]
[ 1.689828] pci 0000:00:1c.7: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 1.689832] pci 0000:00:1c.7: bridge window [mem pref disabled]
[ 1.689845] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.689848] pci 0000:00:1c.0: setting latency timer to 64
[ 1.689855] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.689858] pci 0000:00:1c.2: setting latency timer to 64
[ 1.689868] pci 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.689876] pci 0000:02:00.0: setting latency timer to 64
[ 1.689882] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.689886] pci 0000:00:1c.4: setting latency timer to 64
[ 1.689892] pci 0000:00:1c.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 1.689895] pci 0000:00:1c.7: setting latency timer to 64
[ 1.689899] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.689900] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.689901] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.689902] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[ 1.689903] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[ 1.689905] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[ 1.689906] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
[ 1.689907] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
[ 1.689908] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
[ 1.689909] pci_bus 0000:00: resource 13 [mem 0xdfa00000-0xfeafffff]
[ 1.689911] pci_bus 0000:02: resource 1 [mem 0xf7e00000-0xf7efffff]
[ 1.689912] pci_bus 0000:03: resource 1 [mem 0xf7e00000-0xf7efffff]
[ 1.689913] pci_bus 0000:03: resource 5 [mem 0xf7e00000-0xf7efffff]
[ 1.689915] pci_bus 0000:04: resource 1 [mem 0xf7d00000-0xf7dfffff]
[ 1.689916] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 1.689917] pci_bus 0000:05: resource 1 [mem 0xf7c00000-0xf7cfffff]
[ 1.689962] NET: Registered protocol family 2
[ 1.690175] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 1.690783] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 1.691732] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.691847] TCP: Hash tables configured (established 524288 bind 65536)
[ 1.691849] TCP reno registered
[ 1.691861] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.691904] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.692194] NET: Registered protocol family 1
[ 1.692203] pci 0000:00:02.0: Boot video device
[ 1.692211] pci 0000:00:14.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.692263] pci 0000:00:14.0: PCI INT A disabled
[ 1.692275] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.710295] pci 0000:00:1a.0: PCI INT A disabled
[ 1.710331] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.730234] pci 0000:00:1d.0: PCI INT A disabled
[ 1.730273] pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.730306] pci 0000:04:00.0: PCI INT A disabled
[ 1.730311] PCI: CLS 64 bytes, default 64
[ 1.730338] Unpacking initramfs...
[ 1.925914] Freeing initrd memory: 2604k freed
[ 1.926127] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.926128] Placing 64MB software IO TLB between ffff8800d5b29000 - ffff8800d9b29000
[ 1.926130] software IO TLB at phys 0xd5b29000 - 0xd9b29000
[ 1.926519] audit: initializing netlink socket (disabled)
[ 1.926525] type=2000 audit(1359046522.740:1): initialized
[ 1.933772] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.935521] VFS: Disk quotas dquot_6.5.2
[ 1.935612] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.935737] msgmni has been set to 31953
[ 1.935878] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.935900] io scheduler noop registered
[ 1.935901] io scheduler deadline registered (default)
[ 1.935930] io scheduler cfq registered
[ 1.936180] intel_idle: MWAIT substates: 0x1120
[ 1.936181] intel_idle: does not run on family 6 model 58
[ 1.936184] ERST: Table is not found!
[ 1.936212] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.597909] Linux agpgart interface v0.103
[ 2.597959] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 2.600776] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.600780] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.600816] mousedev: PS/2 mouse device common for all mice
[ 2.600840] rtc_cmos 00:06: RTC can wake from S4
[ 2.600915] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 2.600942] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 2.600947] cpuidle: using governor ladder
[ 2.600947] cpuidle: using governor menu
[ 2.601062] TCP cubic registered
[ 2.601170] NET: Registered protocol family 10
[ 2.601503] NET: Registered protocol family 17
[ 2.601506] Registering the dns_resolver key type
[ 2.601551] PM: Hibernation image not present or could not be loaded.
[ 2.601556] registered taskstats version 1
[ 2.602319] rtc_cmos 00:06: setting system clock to 2013-01-24 16:55:24 UTC (1359046524)
[ 2.602355] Initializing network drop monitor service
[ 2.603044] Freeing unused kernel memory: 740k freed
[ 2.603103] Write protecting the kernel read-only data: 8192k
[ 2.605976] Freeing unused kernel memory: 1856k freed
[ 2.607156] Freeing unused kernel memory: 660k freed
[ 2.611444] systemd-udevd[60]: starting version 197
[ 2.612701] SCSI subsystem initialized
[ 2.613514] libata version 3.00 loaded.
[ 2.613832] ahci 0000:00:1f.2: version 3.0
[ 2.613842] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.613887] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
[ 2.627690] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x21 impl SATA mode
[ 2.627703] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
[ 2.627707] ahci 0000:00:1f.2: setting latency timer to 64
[ 2.658165] scsi0 : ahci
[ 2.658288] scsi1 : ahci
[ 2.658370] scsi2 : ahci
[ 2.658462] scsi3 : ahci
[ 2.658549] scsi4 : ahci
[ 2.658602] scsi5 : ahci
[ 2.658798] ata1: SATA max UDMA/133 abar m2048@0xf7f36000 port 0xf7f36100 irq 40
[ 2.658800] ata2: DUMMY
[ 2.658801] ata3: DUMMY
[ 2.658801] ata4: DUMMY
[ 2.658802] ata5: DUMMY
[ 2.658804] ata6: SATA max UDMA/133 abar m2048@0xf7f36000 port 0xf7f36380 irq 40
[ 2.658832] ahci 0000:05:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.658890] ahci 0000:05:00.0: irq 41 for MSI/MSI-X
[ 2.658953] ahci 0000:05:00.0: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 2.658955] ahci 0000:05:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 2.658960] ahci 0000:05:00.0: setting latency timer to 64
[ 2.659205] scsi6 : ahci
[ 2.659275] scsi7 : ahci
[ 2.659373] ata7: SATA max UDMA/133 abar m512@0xf7c20000 port 0xf7c20100 irq 41
[ 2.659376] ata8: SATA max UDMA/133 abar m512@0xf7c20000 port 0xf7c20180 irq 41
[ 2.926811] Refined TSC clocksource calibration: 3392.292 MHz.
[ 2.926816] Switching to clocksource tsc
[ 3.006586] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.016566] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.016575] ata8: SATA link down (SStatus 0 SControl 300)
[ 3.016618] ata7: SATA link down (SStatus 0 SControl 300)
[ 3.017996] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 3.018001] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 3.018005] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 3.028400] ata1.00: ATA-9: INTEL SSDSC2CT240A4, 335s, max UDMA/133
[ 3.028403] ata1.00: 468862128 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 3.037939] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 3.037943] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 3.037946] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 3.047922] ata1.00: configured for UDMA/133
[ 3.048004] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSC2CT24 335s PQ: 0 ANSI: 5
[ 3.048486] sd 0:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/223 GiB)
[ 3.048533] sd 0:0:0:0: [sda] Write Protect is off
[ 3.048535] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.048548] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.048783] sda: sda1 sda2 sda3
[ 3.048974] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.049021] usbcore: registered new interface driver usbfs
[ 3.049040] usbcore: registered new interface driver hub
[ 3.049058] usbcore: registered new device driver usb
[ 3.049418] xhci_hcd 0000:00:14.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.049444] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 3.049447] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 3.049457] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 3.049537] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 3.049547] xhci_hcd 0000:00:14.0: irq 16, io mem 0xf7f20000
[ 3.049559] xhci_hcd 0000:00:14.0: Failed to enable MSI-X
[ 3.049634] xhci_hcd 0000:00:14.0: irq 42 for MSI/MSI-X
[ 3.049712] xHCI xhci_add_endpoint called for root hub
[ 3.049713] xHCI xhci_check_bandwidth called for root hub
[ 3.049727] hub 1-0:1.0: USB hub found
[ 3.049733] hub 1-0:1.0: 4 ports detected
[ 3.049776] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 3.049779] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 3.049843] xHCI xhci_add_endpoint called for root hub
[ 3.049844] xHCI xhci_check_bandwidth called for root hub
[ 3.049867] hub 2-0:1.0: USB hub found
[ 3.049872] hub 2-0:1.0: 4 ports detected
[ 3.049912] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.049925] xhci_hcd 0000:04:00.0: setting latency timer to 64
[ 3.049928] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 3.049932] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3
[ 3.050087] xhci_hcd 0000:04:00.0: irq 16, io mem 0xf7d00000
[ 3.050139] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 3.050141] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 3.050142] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 3.050144] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 3.050146] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X
[ 3.050148] xhci_hcd 0000:04:00.0: irq 48 for MSI/MSI-X
[ 3.050150] xhci_hcd 0000:04:00.0: irq 49 for MSI/MSI-X
[ 3.050152] xhci_hcd 0000:04:00.0: irq 50 for MSI/MSI-X
[ 3.050285] xHCI xhci_add_endpoint called for root hub
[ 3.050286] xHCI xhci_check_bandwidth called for root hub
[ 3.050299] hub 3-0:1.0: USB hub found
[ 3.050305] hub 3-0:1.0: 2 ports detected
[ 3.050347] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 3.050350] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 4
[ 3.053530] xHCI xhci_add_endpoint called for root hub
[ 3.053531] xHCI xhci_check_bandwidth called for root hub
[ 3.053542] hub 4-0:1.0: USB hub found
[ 3.053548] hub 4-0:1.0: 2 ports detected
[ 3.053821] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.053833] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.053846] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 3.053849] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 3.053858] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 5
[ 3.053877] ehci_hcd 0000:00:1a.0: debug port 2
[ 3.057759] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 3.057766] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf7f38000
[ 3.076378] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 3.076460] hub 5-0:1.0: USB hub found
[ 3.076461] hub 5-0:1.0: 2 ports detected
[ 3.076503] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.076513] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.076516] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 3.076519] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 3.076538] ehci_hcd 0000:00:1d.0: debug port 2
[ 3.080400] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 3.080409] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf7f37000
[ 3.096318] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 3.096397] hub 6-0:1.0: USB hub found
[ 3.096399] hub 6-0:1.0: 2 ports detected
[ 3.100181] [drm] Initialized drm 1.1.0 20060810
[ 3.100649] agpgart-intel 0000:00:00.0: Intel Ivybridge Chipset
[ 3.100748] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 3.102008] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[ 3.102090] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 3.102374] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 3.102378] ACPI: Power Button [PWRB]
[ 3.102404] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 3.102406] ACPI: Power Button [PWRF]
[ 3.104565] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.104568] i915 0000:00:02.0: setting latency timer to 64
[ 3.150773] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[ 3.150775] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 3.151055] i915 0000:00:02.0: irq 51 for MSI/MSI-X
[ 3.151059] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 3.151061] [drm] Driver supports precise vblank timestamp query.
[ 3.151122] [drm:intel_dsm_platform_mux_info] *ERROR* MUX INFO call failed
[ 3.151186] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 3.218032] ------------[ cut here ]------------
[ 3.218041] WARNING: at drivers/gpu/drm/i915/i915_drv.c:322 gen6_gt_force_wake_get+0x4e/0x50 [i915]()
[ 3.218042] Hardware name:
[ 3.218043] Modules linked in: i915(+) video button i2c_algo_bit intel_agp intel_gtt drm_kms_helper drm i2c_core ext4 crc16 jbd2 mbcache ehci_hcd xhci_hcd usbcore sd_mod ahci libahci libata scsi_mod
[ 3.218051] Pid: 61, comm: modprobe Not tainted 3.0.60-1-lts #1
[ 3.218052] Call Trace:
[ 3.218056] [<ffffffff8105a64f>] warn_slowpath_common+0x7f/0xc0
[ 3.218059] [<ffffffff8105a6aa>] warn_slowpath_null+0x1a/0x20
[ 3.218065] [<ffffffffa01c069e>] gen6_gt_force_wake_get+0x4e/0x50 [i915]
[ 3.218073] [<ffffffffa01ede62>] ivybridge_init_clock_gating+0x662/0x680 [i915]
[ 3.218081] [<ffffffffa0207ecf>] intel_modeset_init+0x83f/0x1670 [i915]
[ 3.218088] [<ffffffffa01c1dd0>] ? i915_switcheroo_can_switch+0x40/0x40 [i915]
[ 3.218094] [<ffffffffa01c47a0>] i915_driver_load+0xd50/0x15a0 [i915]
[ 3.218098] [<ffffffff812e2e0e>] ? device_register+0x1e/0x30
[ 3.218102] [<ffffffffa01761b6>] ? drm_sysfs_device_add+0x86/0xb0 [drm]
[ 3.218105] [<ffffffffa0172400>] ? drm_get_minor+0x210/0x2f0 [drm]
[ 3.218109] [<ffffffffa01748ee>] drm_get_pci_dev+0x18e/0x2c0 [drm]
[ 3.218118] [<ffffffffa0228d72>] i915_pci_probe+0x16/0x20 [i915]
[ 3.218120] [<ffffffff8123ea4c>] local_pci_probe+0x5c/0xd0
[ 3.218122] [<ffffffff8123f281>] pci_device_probe+0x111/0x120
[ 3.218124] [<ffffffff812e5976>] driver_probe_device+0x96/0x2b0
[ 3.218126] [<ffffffff812e5c3b>] __driver_attach+0xab/0xb0
[ 3.218127] [<ffffffff812e5b90>] ? driver_probe_device+0x2b0/0x2b0
[ 3.218129] [<ffffffff812e4486>] bus_for_each_dev+0x46/0x90
[ 3.218131] [<ffffffff812e558e>] driver_attach+0x1e/0x20
[ 3.218134] [<ffffffff812e5178>] bus_add_driver+0x1a8/0x2a0
[ 3.218135] [<ffffffffa0144000>] ? 0xffffffffa0143fff
[ 3.218137] [<ffffffff812e6407>] driver_register+0x77/0x160
[ 3.218138] [<ffffffffa0144000>] ? 0xffffffffa0143fff
[ 3.218140] [<ffffffff8123f453>] __pci_register_driver+0x63/0xe0
[ 3.218142] [<ffffffffa0144000>] ? 0xffffffffa0143fff
[ 3.218145] [<ffffffffa0174b3a>] drm_pci_init+0x11a/0x130 [drm]
[ 3.218146] [<ffffffffa0144000>] ? 0xffffffffa0143fff
[ 3.218152] [<ffffffffa014408b>] i915_init+0x8b/0x8d [i915]
[ 3.218154] [<ffffffff81002132>] do_one_initcall+0x132/0x190
[ 3.218156] [<ffffffff81099b84>] sys_init_module+0x84/0x1e0
[ 3.218160] [<ffffffff814275c2>] system_call_fastpath+0x16/0x1b
[ 3.218161] ---[ end trace b067b1330875c05d ]---
[ 3.218665] ------------[ cut here ]------------
[ 3.218671] WARNING: at drivers/gpu/drm/i915/i915_drv.c:340 gen6_gt_force_wake_put+0x58/0x60 [i915]()
[ 3.218672] Hardware name:
[ 3.218672] Modules linked in: i915(+) video button i2c_algo_bit intel_agp intel_gtt drm_kms_helper drm i2c_core ext4 crc16 jbd2 mbcache ehci_hcd xhci_hcd usbcore sd_mod ahci libahci libata scsi_mod
[ 3.218679] Pid: 61, comm: modprobe Tainted: G W 3.0.60-1-lts #1
[ 3.218680] Call Trace:
[ 3.218682] [<ffffffff8105a64f>] warn_slowpath_common+0x7f/0xc0
[ 3.218684] [<ffffffff8105a6aa>] warn_slowpath_null+0x1a/0x20
[ 3.218689] [<ffffffffa01c06f8>] gen6_gt_force_wake_put+0x58/0x60 [i915]
[ 3.218696] [<ffffffffa01ede76>] ivybridge_init_clock_gating+0x676/0x680 [i915]
[ 3.218704] [<ffffffffa0207ecf>] intel_modeset_init+0x83f/0x1670 [i915]
[ 3.218709] [<ffffffffa01c1dd0>] ? i915_switcheroo_can_switch+0x40/0x40 [i915]
[ 3.218715] [<ffffffffa01c47a0>] i915_driver_load+0xd50/0x15a0 [i915]
[ 3.218717] [<ffffffff812e2e0e>] ? device_register+0x1e/0x30
[ 3.218721] [<ffffffffa01761b6>] ? drm_sysfs_device_add+0x86/0xb0 [drm]
[ 3.218724] [<ffffffffa0172400>] ? drm_get_minor+0x210/0x2f0 [drm]
[ 3.218727] [<ffffffffa01748ee>] drm_get_pci_dev+0x18e/0x2c0 [drm]
[ 3.218735] [<ffffffffa0228d72>] i915_pci_probe+0x16/0x20 [i915]
[ 3.218737] [<ffffffff8123ea4c>] local_pci_probe+0x5c/0xd0
[ 3.218739] [<ffffffff8123f281>] pci_device_probe+0x111/0x120
[ 3.218741] [<ffffffff812e5976>] driver_probe_device+0x96/0x2b0
[ 3.218742] [<ffffffff812e5c3b>] __driver_attach+0xab/0xb0
[ 3.218744] [<ffffffff812e5b90>] ? driver_probe_device+0x2b0/0x2b0
[ 3.218746] [<ffffffff812e4486>] bus_for_each_dev+0x46/0x90
[ 3.218748] [<ffffffff812e558e>] driver_attach+0x1e/0x20
[ 3.218750] [<ffffffff812e5178>] bus_add_driver+0x1a8/0x2a0
[ 3.218751] [<ffffffffa0144000>] ? 0xffffffffa0143fff
[ 3.218753] [<ffffffff812e6407>] driver_register+0x77/0x160
[ 3.218754] [<ffffffffa0144000>] ? 0xffffffffa0143fff
[ 3.218756] [<ffffffff8123f453>] __pci_register_driver+0x63/0xe0
[ 3.218757] [<ffffffffa0144000>] ? 0xffffffffa0143fff
[ 3.218760] [<ffffffffa0174b3a>] drm_pci_init+0x11a/0x130 [drm]
[ 3.218762] [<ffffffffa0144000>] ? 0xffffffffa0143fff
[ 3.218767] [<ffffffffa014408b>] i915_init+0x8b/0x8d [i915]
[ 3.218768] [<ffffffff81002132>] do_one_initcall+0x132/0x190
[ 3.218770] [<ffffffff81099b84>] sys_init_module+0x84/0x1e0
[ 3.218772] [<ffffffff814275c2>] system_call_fastpath+0x16/0x1b
[ 3.218773] ---[ end trace b067b1330875c05e ]---
[ 3.365550] usb 3-1: new low speed USB device number 2 using xhci_hcd
[ 3.437488] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep
[ 3.451461] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep
[ 3.456435] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep
[ 3.457504] usb 3-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 3.457511] usb 3-1: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 3.525839] fbcon: inteldrmfb (fb0) is primary device
[ 3.574957] usb 5-1: new high speed USB device number 2 using ehci_hcd
[ 3.725061] hub 5-1:1.0: USB hub found
[ 3.725159] hub 5-1:1.0: 6 ports detected
[ 3.844189] usb 6-1: new high speed USB device number 2 using ehci_hcd
[ 3.947221] Console: switching to colour frame buffer device 128x48
[ 3.948367] fb0: inteldrmfb frame buffer device
[ 3.948368] drm: registered panic notifier
[ 3.994297] hub 6-1:1.0: USB hub found
[ 3.994387] hub 6-1:1.0: 8 ports detected
[ 4.033922] acpi device:4c: registered as cooling_device0
[ 4.034083] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input2
[ 4.034088] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.034117] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.048356] firewire_ohci 0000:03:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 4.103595] firewire_ohci: Added fw-ohci device 0000:03:02.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
[ 4.751576] irq 16: nobody cared (try booting with the "irqpoll" option)
[ 4.751630] Pid: 0, comm: swapper Tainted: G W 3.0.60-1-lts #1
[ 4.751632] Call Trace:
[ 4.751633] <IRQ> [<ffffffff810bd7fa>] __report_bad_irq+0x3a/0xd0
[ 4.751639] [<ffffffff810bdaca>] note_interrupt+0x19a/0x1e0
[ 4.751641] [<ffffffff810bbae8>] handle_irq_event_percpu+0xa8/0x1e0
[ 4.751643] [<ffffffff810bbc5a>] handle_irq_event+0x3a/0x60
[ 4.751645] [<ffffffff810be3b6>] handle_fasteoi_irq+0x56/0xf0
[ 4.751648] [<ffffffff8100c152>] handle_irq+0x22/0x40
[ 4.751650] [<ffffffff8142902a>] do_IRQ+0x5a/0xe0
[ 4.751652] [<ffffffff8141fad3>] common_interrupt+0x13/0x13
[ 4.751653] <EOI> [<ffffffff81011ea2>] ? mwait_idle+0x92/0x1d0
[ 4.751658] [<ffffffff81423396>] ? atomic_notifier_call_chain+0x16/0x20
[ 4.751660] [<ffffffff8100920b>] cpu_idle+0xab/0x100
[ 4.751663] [<ffffffff813fea6e>] rest_init+0x72/0x74
[ 4.751665] [<ffffffff81950bfa>] start_kernel+0x3c5/0x3d0
[ 4.751667] [<ffffffff81950347>] x86_64_start_reservations+0x132/0x136
[ 4.751669] [<ffffffff8195044b>] x86_64_start_kernel+0x100/0x10f
[ 4.751670] handlers:
[ 4.751681] [<ffffffffa008fdd0>] usb_hcd_irq
[ 4.751694] Disabling IRQ #16
[ 4.813741] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: user_xattr,barrier=1,data=ordered
[ 6.556477] systemd[1]: systemd 197 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 6.559073] systemd[1]: Set hostname to <polymnie>.
[ 6.665661] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory. See system logs and 'systemctl status display-manager.service' for details.
[ 6.665764] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 6.665792] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 6.665800] systemd[1]: Starting Remote File Systems.
[ 6.665857] systemd[1]: Reached target Remote File Systems.
[ 6.665863] systemd[1]: Starting Delayed Shutdown Socket.
[ 6.665921] systemd[1]: Listening on Delayed Shutdown Socket.
[ 6.665927] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 6.665982] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 6.665988] systemd[1]: Starting Encrypted Volumes.
[ 6.666031] systemd[1]: Reached target Encrypted Volumes.
[ 6.666064] systemd[1]: Starting udev Kernel Socket.
[ 6.666124] systemd[1]: Listening on udev Kernel Socket.
[ 6.666153] systemd[1]: Starting udev Control Socket.
[ 6.666207] systemd[1]: Listening on udev Control Socket.
[ 6.666227] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 6.666329] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 6.666338] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 6.666357] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 6.666362] systemd[1]: Starting Swap.
[ 6.666404] systemd[1]: Reached target Swap.
[ 6.666410] systemd[1]: Expecting device dev-disk-by\x2dlabel-Boot.device...
[ 6.666450] systemd[1]: Starting Journal Socket.
[ 6.666517] systemd[1]: Listening on Journal Socket.
[ 6.666555] systemd[1]: Started File System Check on Root Device.
[ 6.666560] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 6.985276] systemd[1]: Mounting Temporary Directory...
[ 6.993812] EXT4-fs (sda3): re-mounted. Opts: (null)
[ 7.396212] systemd[1]: Starting Apply Kernel Variables...
[ 7.785039] systemd[1]: Started Set Up Additional Binary Formats.
[ 7.785052] systemd[1]: Mounting Debug File System...
[ 8.072150] systemd[1]: Mounting POSIX Message Queue File System...
[ 8.381270] systemd[1]: Mounting Huge Pages File System...
[ 8.650491] systemd[1]: Starting Setup Virtual Console...
[ 8.972595] systemd[1]: Started Load Kernel Modules.
[ 8.972606] systemd[1]: Mounted Configuration File System.
[ 8.972612] systemd[1]: Mounted FUSE Control File System.
[ 8.972641] systemd[1]: Starting udev Kernel Device Manager...
[ 9.368480] systemd[1]: Starting udev Coldplug all Devices...
[ 9.528034] systemd-udevd[149]: starting version 197
[ 9.707493] systemd[1]: Starting Journal Service...
[ 9.867098] systemd[1]: Started Journal Service.
[ 9.867321] systemd[1]: Started udev Kernel Device Manager.
[ 10.186134] systemd[1]: Started Remount Root and Kernel File Systems.
[ 10.186678] systemd[1]: Mounted Temporary Directory.
[ 10.505665] systemd[1]: Started Apply Kernel Variables.
[ 10.506202] systemd[1]: Mounted Debug File System.
[ 10.506733] systemd[1]: Mounted POSIX Message Queue File System.
[ 10.507258] systemd[1]: Mounted Huge Pages File System.
[ 10.834713] systemd[1]: Started Setup Virtual Console.
[ 11.153354] systemd[1]: Starting Local File Systems (Pre).
[ 11.153843] systemd[1]: Reached target Local File Systems (Pre).
[ 11.153853] systemd[1]: Starting Load Random Seed...
[ 11.166916] iTCO_vendor_support: vendor-support=0
[ 11.167689] ACPI: acpi_idle registered with cpuidle
[ 11.169288] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[ 11.169371] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
[ 11.169427] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 11.169722] mei: module is from the staging directory, the quality is unknown, you have been warned.
[ 11.169892] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 11.169897] mei 0000:00:16.0: setting latency timer to 64
[ 11.174102] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[ 11.174107] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 11.174172] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 11.174192] e1000e 0000:00:19.0: setting latency timer to 64
[ 11.174473] e1000e 0000:00:19.0: irq 52 for MSI/MSI-X
[ 11.232446] input: wired keyboard as /devices/pci0000:00/0000:00:1c.4/0000:04:00.0/usb3/3-1/3-1:1.0/input/input3
[ 11.232491] generic-usb 0003:046A:0180.0001: input,hidraw0: USB HID v1.11 Keyboard [ wired keyboard] on usb-0000:04:00.0-1/input0
[ 11.233234] wmi: Mapper loaded
[ 11.233464] Monitor-Mwait will be used to enter C-1 state
[ 11.233471] Monitor-Mwait will be used to enter C-2 state
[ 11.233697] thermal LNXTHERM:00: registered as thermal_zone0
[ 11.233699] ACPI: Thermal Zone [TZ00] (28 C)
[ 11.234027] thermal LNXTHERM:01: registered as thermal_zone1
[ 11.234029] ACPI: Thermal Zone [TZ01] (30 C)
[ 11.234199] ACPI: Fan [FAN0] (off)
[ 11.234289] ACPI: Fan [FAN1] (off)
[ 11.234488] ACPI: Fan [FAN2] (off)
[ 11.234545] ACPI: Fan [FAN3] (off)
[ 11.234573] ACPI: Fan [FAN4] (off)
[ 11.240270] xhci_hcd 0000:04:00.0: WARN: Stalled endpoint
[ 11.266225] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep
[ 11.272211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep
[ 11.273281] input: wired keyboard as /devices/pci0000:00/0000:00:1c.4/0000:04:00.0/usb3/3-1/3-1:1.1/input/input4
[ 11.273330] generic-usb 0003:046A:0180.0002: input,hidraw1: USB HID v1.11 Device [ wired keyboard] on usb-0000:04:00.0-1/input1
[ 11.273344] usbcore: registered new interface driver usbhid
[ 11.273346] usbhid: USB HID core driver
[ 11.293045] systemd[1]: Hardware watchdog 'iTCO_wdt', version 0
[ 11.293068] systemd[1]: Set hardware watchdog to 10s.
[ 11.502137] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:22:4d:86:69:c9
[ 11.502140] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 11.502188] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF
[ 11.502223] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 11.502310] HDA Intel 0000:00:1b.0: irq 53 for MSI/MSI-X
[ 11.502334] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 11.502823] systemd[1]: Started udev Coldplug all Devices.
[ 11.727947] irq 16: nobody cared (try booting with the "irqpoll" option)
[ 11.728870] Pid: 0, comm: kworker/0:0 Tainted: G WC 3.0.60-1-lts #1
[ 11.728872] Call Trace:
[ 11.728874] <IRQ> [<ffffffff810bd7fa>] __report_bad_irq+0x3a/0xd0
[ 11.728881] [<ffffffff810bdaca>] note_interrupt+0x19a/0x1e0
[ 11.728884] [<ffffffff810bbae8>] handle_irq_event_percpu+0xa8/0x1e0
[ 11.728887] [<ffffffff810bbc5a>] handle_irq_event+0x3a/0x60
[ 11.728890] [<ffffffff810be3b6>] handle_fasteoi_irq+0x56/0xf0
[ 11.728893] [<ffffffff8100c152>] handle_irq+0x22/0x40
[ 11.728896] [<ffffffff8142902a>] do_IRQ+0x5a/0xe0
[ 11.728899] [<ffffffff8141fad3>] common_interrupt+0x13/0x13
[ 11.728900] <EOI> [<ffffffffa014bd53>] ? acpi_idle_enter_c1+0xba/0xdc [processor]
[ 11.728908] [<ffffffffa014bd31>] ? acpi_idle_enter_c1+0x98/0xdc [processor]
[ 11.728913] [<ffffffff8130e4b4>] cpuidle_idle_call+0xa4/0x230
[ 11.728916] [<ffffffff8100920b>] cpu_idle+0xab/0x100
[ 11.728920] [<ffffffff8140fe4a>] start_secondary+0x262/0x264
[ 11.728922] handlers:
[ 11.729841] [<ffffffffa008fdd0>] usb_hcd_irq
[ 11.730751] [<ffffffffa02be9b0>] mei_interrupt_quick_handler threaded [<ffffffffa02bef40>] mei_interrupt_thread_handler
[ 11.731714] Disabling IRQ #16
[ 11.902151] systemd[1]: Started Load Random Seed.
[ 12.115963] hda_codec: ALC898: BIOS auto-probing.
[ 12.116695] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input5
[ 12.118904] HDMI status: Pin=6 Presence_Detect=1 ELD_Valid=1
[ 12.122724] HDMI status: Pin=7 Presence_Detect=0 ELD_Valid=0
[ 12.125592] HDMI hot plug event: Pin=6 Presence_Detect=1 ELD_Valid=1
[ 12.125659] HDMI status: Pin=6 Presence_Detect=1 ELD_Valid=1
[ 12.125763] input: HDA Intel PCH HDMI/DP as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 12.125804] input: HDA Intel PCH HDMI/DP as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 12.125843] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 12.125959] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 12.125963] ACPI: resource 0000:00:1f.3 [io 0xf040-0xf05f] conflicts with ACPI region SMBI [io 0xf040-0xf04f]
[ 12.125964] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 12.129214] HDMI hot plug event: Pin=6 Presence_Detect=1 ELD_Valid=1
[ 12.129247] HDMI status: Pin=6 Presence_Detect=1 ELD_Valid=1
[ 12.171213] systemd[1]: Found device INTEL_SSDSC2CT240A4.
[ 12.171234] systemd[1]: Starting File System Check on /dev/disk/by-label/Boot...
[ 12.900087] systemd[1]: Starting Sound Card.
[ 12.900613] systemd[1]: Reached target Sound Card.
[ 13.546996] systemd[1]: Started File System Check on /dev/disk/by-label/Boot.
[ 13.547018] systemd[1]: Mounting /boot...
[ 13.887313] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[ 13.888188] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 14.235109] systemd[1]: Mounted /boot.
[ 14.235129] systemd[1]: Starting Local File Systems.
[ 14.235654] systemd[1]: Reached target Local File Systems.
[ 14.237140] systemd[1]: Starting Recreate Volatile Files and Directories...
[ 14.643385] systemd[1]: Starting Trigger Flushing of Journal to Persistent Storage...
[ 15.292027] systemd[1]: Started Recreate Volatile Files and Directories.
[ 15.292050] systemd[1]: Starting System Initialization.
[ 15.292593] systemd[1]: Reached target System Initialization.
[ 15.292602] systemd[1]: Starting D-Bus System Message Bus Socket.
[ 15.293155] systemd[1]: Listening on D-Bus System Message Bus Socket.
[ 15.293163] systemd[1]: Starting Sockets.
[ 15.293701] systemd[1]: Reached target Sockets.
[ 15.293708] systemd[1]: Starting Daily Cleanup of Temporary Directories.
[ 15.293720] systemd[1]: Started Daily Cleanup of Temporary Directories.
[ 15.293727] systemd[1]: Starting Basic System.
[ 15.294262] systemd[1]: Reached target Basic System.
[ 15.295935] systemd[1]: Started SSH Key Generation.
[ 15.295952] systemd[1]: Starting OpenSSH Daemon...
[ 15.551382] systemd[1]: Started OpenSSH Daemon.
[ 15.551410] systemd[1]: Starting Netcfg multi-profile daemon...
[ 15.879849] systemd[1]: Starting Login Service...
[ 16.059382] e1000e 0000:00:19.0: irq 52 for MSI/MSI-X
[ 16.119132] e1000e 0000:00:19.0: irq 52 for MSI/MSI-X
[ 16.119929] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.139138] systemd[1]: Starting D-Bus System Message Bus...
[ 16.458740] systemd[1]: Started D-Bus System Message Bus.
[ 18.622589] systemd[1]: Started Login Service.
[ 18.622777] systemd-journald[154]: Received SIGUSR1
[ 19.001403] systemd[1]: Started Trigger Flushing of Journal to Persistent Storage.
[ 19.001429] systemd[1]: Starting Permit User Sessions...
[ 19.649561] systemd[1]: Started Permit User Sessions.
[ 19.649584] systemd[1]: Starting Getty on tty1...
[ 19.683840] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 19.684610] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.018622] systemd[1]: Started Getty on tty1.
[ 20.018648] systemd[1]: Starting Login Prompts.
[ 20.019171] systemd[1]: Reached target Login Prompts.
[ 29.869750] eth0: no IPv6 routers present
[ 600.577731] HDMI hot plug event: Pin=6 Presence_Detect=0 ELD_Valid=1
[ 600.577767] HDMI status: Pin=6 Presence_Detect=0 ELD_Valid=0
[ 1166.702730] systemd-journald[154]: File /var/log/journal/fcd13ea2b4d34a0da97941751e3698a8/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
# systool -m i915 -av
Module = "i915"
Attributes:
initstate = "live"
refcnt = "1"
Parameters:
fbpercrtc = "0"
i915_enable_fbc = "0"
i915_enable_rc6 = "0"
lvds_downclock = "0"
lvds_use_ssc = "1"
modeset = "-1"
panel_ignore_lid = "0"
powersave = "1"
reset = "Y"
semaphores = "0"
vbt_sdvo_panel_type = "-1"
Sections:
.altinstr_replacement= "0xffffffffa02295af"
.altinstructions = "0xffffffffa023bbe8"
.bss = "0xffffffffa0248718"
.data = "0xffffffffa023bfe0"
.devinit.text = "0xffffffffa0228d5c"
.exit.text = "0xffffffffa0228d7c"
.fixup = "0xffffffffa02294ac"
.gnu.linkonce.this_module= "0xffffffffa02484c0"
.init.text = "0xffffffffa0144000"
.note.gnu.build-id = "0xffffffffa02295c8"
.parainstructions = "0xffffffffa023b6b8"
.rodata = "0xffffffffa0229680"
.rodata.str1.1 = "0xffffffffa0236891"
.rodata.str1.8 = "0xffffffffa0232500"
.smp_locks = "0xffffffffa0239f50"
.strtab = "0xffffffffa014ef68"
.symtab = "0xffffffffa01440f0"
.text = "0xffffffffa01c0000"
.text.unlikely = "0xffffffffa0228d95"
__bug_table = "0xffffffffa023b824"
__ex_table = "0xffffffffa023ba58"
__jump_table = "0xffffffffa023e8c0"
__kcrctab_gpl = "0xffffffffa0229640"
__ksymtab_gpl = "0xffffffffa02295f0"
__ksymtab_strings = "0xffffffffa023b660"
__mcount_loc = "0xffffffffa023a0d8"
__param = "0xffffffffa0239f78"
__tracepoints_ptrs = "0xffffffffa023bc60"
__tracepoints_strings= "0xffffffffa023bd20"
__tracepoints = "0xffffffffa0247f00"
_ftrace_events = "0xffffffffa0247e30"
# cat /etc/mkinitcpio.conf
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES="ahci libahci xhci-hcd ehci-hcd ext2 ext4 i915"
# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image. This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way. This is useful for config files.
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
## This setup specifies all modules in the MODULES setting above.
## No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
#
## This setup will autodetect all modules for your system and should
## work as a sane default
# HOOKS="base udev autodetect block filesystems"
#
## This setup will generate a 'full' image which supports most systems.
## No autodetection is done.
# HOOKS="base udev block filesystems"
#
## This setup assembles a pata mdadm array with an encrypted root FS.
## Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
# HOOKS="base udev block mdadm encrypt filesystems"
#
## This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev block lvm2 filesystems"
#
## NOTE: If you have /usr on a separate partition, you MUST include the
# usr, fsck and shutdown hooks.
HOOKS="base udev keymap fsck autodetect block filesystems"
# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
COMPRESSION="xz"
#COMPRESSION="lzop"
# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""
(I think this file was created by the installer.)
# cat /etc/modprobe.d/modprobe.conf
options i915 modeset=1
Last edited by alub (2013-01-24 16:32:41)
Offline
Have you tried removing the libva-intel-driver package? It isn't necessary to run intel graphics.
I'm curious, though. You said you have an i7-3770, but your lspci says Xeon E3-1200.
Last edited by the sad clown (2013-01-24 13:02:03)
I laugh, yet the joke is on me
Offline
Have you tried removing the libva-intel-driver package? It isn't necessary to run intel graphics.
I’m currently trying without it, and I have yet to see X fail. Video playing seems ok (although not tear-free). Thanks!
I'm curious, though. You said you have an i7-3770, but your lspci says Xeon E3-1200.
I’m positive about the i7-3770, the line in lspci is just the RAM Controller.
Edit: when playing with Supertuxkart, I got those errors in dmesg:
[ 896.263466] [drm:i915_hangcheck_ring_idle] *ERROR* Hangcheck timer elapsed... blt ring idle [waiting on 223877, at 223877], missed IRQ?
[ 1023.653768] [drm:i915_hangcheck_ring_idle] *ERROR* Hangcheck timer elapsed... blt ring idle [waiting on 299653, at 299653], missed IRQ?
and then X froze just by switching desktops in XFCE:
(EE) [mi] EQ overflowing. Additional events will be discarded until existing events are processed.
(EE)
(EE) Backtrace:
(EE) 0: /usr/bin/X (xorg_backtrace+0x36) [0x58a426]
(EE) 1: /usr/bin/X (mieqEnqueue+0x26b) [0x56b78b]
(EE) 2: /usr/bin/X (0x400000+0x4c632) [0x44c632]
(EE) 3: /usr/bin/X (xf86PostKeyboardEvent+0x4b) [0x48628b]
(EE) 4: /usr/lib/xorg/modules/input/evdev_drv.so (0x7f1620915000+0x5faf) [0x7f162091afaf]
(EE) 5: /usr/bin/X (0x400000+0x75b97) [0x475b97]
(EE) 6: /usr/bin/X (0x400000+0x9f258) [0x49f258]
(EE) 7: /usr/lib/libpthread.so.0 (0x7f1625509000+0xf1e0) [0x7f16255181e0]
(EE) 8: /usr/lib/libc.so.6 (ioctl+0x7) [0x7f162424d657]
(EE) 9: /usr/lib/libdrm.so.2 (drmIoctl+0x28) [0x7f1625300968]
(EE) 10: /usr/lib/libdrm_intel.so.1 (0x7f1622ad7000+0x9631) [0x7f1622ae0631]
(EE) 11: /usr/lib/libdrm_intel.so.1 (0x7f1622ad7000+0x97a8) [0x7f1622ae07a8]
(EE) 12: /usr/lib/xorg/modules/drivers/intel_drv.so (0x7f1622cf7000+0x1243e) [0x7f1622d0943e]
(EE) 13: /usr/lib/xorg/modules/drivers/intel_drv.so (0x7f1622cf7000+0x28cf7) [0x7f1622d1fcf7]
(EE) 14: /usr/lib/xorg/modules/drivers/intel_drv.so (0x7f1622cf7000+0xed375) [0x7f1622de4375]
(EE) 15: /usr/bin/X (0x400000+0x114491) [0x514491]
(EE) 16: /usr/bin/X (0x400000+0x10d696) [0x50d696]
(EE) 17: /usr/bin/X (0x400000+0x37e61) [0x437e61]
(EE) 18: /usr/bin/X (0x400000+0x2696a) [0x42696a]
(EE) 19: /usr/lib/libc.so.6 (__libc_start_main+0xf5) [0x7f162418da15]
(EE) 20: /usr/bin/X (0x400000+0x26cad) [0x426cad]
(EE)
(EE) [mi] These backtraces from mieqEnqueue may point to a culprit higher up the stack.
(EE) [mi] mieq is *NOT* the cause. It is a victim.
so I’m now running with i915.semaphores=1.
Edit 2: with i915.semaphores=1, X is stable enough, but I have visual glitches (especially in Chromium). Switching from UXA to NoAccel removes those glitches, but then video playing (with either VLC or MPlayer) displays a weird line in the middle…
Last edited by alub (2013-01-24 16:02:06)
Offline
i'd file a bug report:
https://bugs.freedesktop.org/
choose the xorg section, then your driver.
Help me to improve ssh-rdp !
Retroarch User? Try my koko-aio shader !
Offline
I also tried to boot on linux-mainline from AUR (3.8rc4), with the same result: the system reboots.
Edit: I also have troubles with Windows, it seems like a hardware problem. Sorry for the noise.
Last edited by alub (2013-01-25 16:57:20)
Offline
Pages: 1