You are not logged in.

#1 2013-02-17 02:29:51

ReyTiger
Member
Registered: 2013-02-17
Posts: 4

Issues mounting USB using e17

I'm trying to get enlightenment's file manager to mount/unmount a USB stick via the right click menu.

However this causes it to segfault:

Output from dmesg

[11791.250363] usb 3-1.2: new high-speed USB device number 5 using ehci_hcd
[11791.335765] scsi8 : usb-storage 3-1.2:1.0
[11792.518353] scsi 8:0:0:0: Direct-Access     SMI      USB DISK         1100 PQ: 0 ANSI: 4
[11792.519243] sd 8:0:0:0: [sdb] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
[11792.519830] sd 8:0:0:0: [sdb] Write Protect is off
[11792.519833] sd 8:0:0:0: [sdb] Mode Sense: 43 00 00 00
[11792.520447] sd 8:0:0:0: [sdb] No Caching mode page present
[11792.520448] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[11792.523601] sd 8:0:0:0: [sdb] No Caching mode page present
[11792.523606] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[11792.524477]  sdb: sdb1
[11792.527870] sd 8:0:0:0: [sdb] No Caching mode page present
[11792.527871] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[11792.527872] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[11822.969535] enlightenment_f[3960]: segfault at 0 ip 00007f2997b07aa1 sp 00007fffbb08e758 error 4 in libc-2.17.so[7f29979b8000+1a4000]

Also if I mount it manually then try to use the file manager to unmount it, nothing happens.
Suggestions?

Offline

#2 2013-02-17 05:52:38

breed808
Member
From: Australia
Registered: 2012-10-27
Posts: 15

Re: Issues mounting USB using e17

If you open the fileman settings, and look in the 'Device' tab, which mode is displayed?

Offline

#3 2013-02-17 06:05:27

ReyTiger
Member
Registered: 2013-02-17
Posts: 4

Re: Issues mounting USB using e17

Mode is RASTER.


I know it *used* to be Udisks. Not sure what changed.

Offline

#4 2013-02-17 06:09:09

breed808
Member
From: Australia
Registered: 2012-10-27
Posts: 15

Re: Issues mounting USB using e17

Hmm, I had the same issue when it was RASTER, but it's now using Udisks. Problem is, I'm not sure how to force it to use udisks. I assume you've tried a reboot?

Last edited by breed808 (2013-02-17 06:10:04)

Offline

#5 2013-02-17 07:07:39

ReyTiger
Member
Registered: 2013-02-17
Posts: 4

Re: Issues mounting USB using e17

Played around with it some more.

It's RASTER right after I boot.

It changes to Udisks after I plug in my drive and it fails to mount.

Offline

#6 2013-02-20 02:02:13

ReyTiger
Member
Registered: 2013-02-17
Posts: 4

Re: Issues mounting USB using e17

It's now changed from a segfault to a problem with dbus:

[   30.444354] USB Mass Storage support registered.
[   31.641454] scsi 6:0:0:0: Direct-Access     SMI      USB DISK         1100 PQ: 0 ANSI: 4
[   31.642511] sd 6:0:0:0: [sdb] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
[   31.643258] sd 6:0:0:0: [sdb] Write Protect is off
[   31.643267] sd 6:0:0:0: [sdb] Mode Sense: 43 00 00 00
[   31.644018] sd 6:0:0:0: [sdb] No Caching mode page present
[   31.644027] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[   31.648332] sd 6:0:0:0: [sdb] No Caching mode page present
[   31.648340] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[   31.649211]  sdb: sdb1
[   31.651603] sd 6:0:0:0: [sdb] No Caching mode page present
[   31.651610] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[   31.651614] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[   61.785709] traps: enlightenment_f[451] general protection ip:7f55293d83a0 sp:7fff5baaf088 error:0 in libdbus-1.so.3.7.2[7f55293b0000+44000]

Offline

Board footer

Powered by FluxBB