You are not logged in.

#1 2013-06-05 04:47:54

dcbdbis
Member
From: Aurora, Colorado
Registered: 2004-09-10
Posts: 247

[SOLVED] Mate Desktop Lost Volume Control After "/bin..." Update

In system tray that is.....

This happened after I did the update as mentioned on the front page that merges the bin folders.

I could not do the update cleanly as a section of Mate was blocking. So I dropped to the CLI, uninstalled all of Mate, reperformed the checks to make sure all was clear, performed the upgrade per the info posted on the front page. Then reinstalled Mate and mate-extras and all is fine....sort of.....

Except I've lost my volume control applet that sits in my system tray. I don't see any other posts along these lines. And it does not appear in the list of applets when I right click the panel and go to "add".

I use PulseAudio. It's up and running fine, and I have access to qpaeq the built in equalizer....So I can adjust my volume...Just not via the sys tray.

Does anyone have any ideas?


Sincerly and respectfully,


Dave

Last edited by dcbdbis (2013-06-06 01:14:20)

Offline

#2 2013-06-05 17:44:48

xpander
Member
Registered: 2013-01-23
Posts: 56

Re: [SOLVED] Mate Desktop Lost Volume Control After "/bin..." Update

do you have mate-media package installed?

with that filesystem update only mate-control-center and mate-power-manager are problematic, since they are in /usr/sbin

so you can just move those 2 files into /usr/bin cause /usr/sbin will be symlink

if you already deleted the real /usr/sbin folder with those files inside.
then reinstall mate-power-manager and mate-control-center (that should put them into /usr/bin via /usr/sbin symlink

Offline

#3 2013-06-05 17:49:39

WonderWoofy
Member
From: Los Gatos, CA
Registered: 2012-05-19
Posts: 8,414

Re: [SOLVED] Mate Desktop Lost Volume Control After "/bin..." Update

Be aware that although things will install along symlinks for now, this functionality will probably be gone with pacman 4.2.  So if you are going to rely on that, then at the very least, change the relevent paths in /var/lib/pacman/local/<package>/files to relfect the real path of the binaries.

Offline

#4 2013-06-06 01:14:07

dcbdbis
Member
From: Aurora, Colorado
Registered: 2004-09-10
Posts: 247

Re: [SOLVED] Mate Desktop Lost Volume Control After "/bin..." Update

Bingo!

I re-installed mate-media and the volume control came back!

After I deinstalled Mate to perform the "/bin...." upgrade from the cli, I had written down the package names on a 3x5 card on the Mate wiki, for re-install to get my desktop back......The wiki article doesn't mention Mate-media, so I didn't write it down on my notes...and as a result I didn't reinstall it.


Thank you very much!


Sincerely and respectfully,


Dave...

Last edited by dcbdbis (2013-06-06 01:15:07)

Offline

#5 2013-06-06 18:47:07

xpander
Member
Registered: 2013-01-23
Posts: 56

Re: [SOLVED] Mate Desktop Lost Volume Control After "/bin..." Update

actually mate-media should come with the mate-extras installation

so there was something wrong on your side probably

Offline

#6 2013-06-06 19:55:44

dcbdbis
Member
From: Aurora, Colorado
Registered: 2004-09-10
Posts: 247

Re: [SOLVED] Mate Desktop Lost Volume Control After "/bin..." Update

Well...you may be right.

I see that mate-media is part of mate-extras...which I did re-install after performing the upgrade.

One thing I didn't think of, is that Mate 1.4 used the older gconfig, where Mate 1.6 uses dconf. I may not have made this transition properly when I upgraded Mate either.

In the "/bin..." upgrade wiki there was a couple of steps to check out your system to make sure you were ready for the upgrade, and it was in performing these steps that I found some Mate 1.4 leftovers. I think that I may have had conflicting pieces of Mate installed as I have been using it for a while through several iterations of this desktop. And Mate 1.6 has a "compatibility layer" for config items still left in gconf that the user may not have ported to dconf. I'll bet you in this section is where I had issues.

Oh well, a good "housecleaning" ended up being a good thing for me. It all ended with everything being back to normal, and fully up to date.


Thanks again for the assistance and the replies, I appreciate it!


Regards,


Dave

Offline

Board footer

Powered by FluxBB