SDHC card will not mount.

diesel1 · 2013-07-31 01:23:20

Hi all,

I have an SDHC card that will not mount in my current system, latest -Syu, up to date. The card and reader will mount and read/write under other Linux systems and also under other, live , linux systems on this pc. It also works fine in the camera, Canon 500D.

Here is the latest dmesg output.....

[ 632.774258] usb 1-2: new high-speed USB device number 5 using ehci-pci
[ 632.922908] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 632.923175] scsi8 : usb-storage 1-2:1.0
[ 632.923357] usbcore: registered new interface driver usb-storage
[ 633.925173] scsi 8:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0 CCS
[ 633.926880] sd 8:0:0:0: [sdg] 63078400 512-byte logical blocks: (32.2 GB/30.0 GiB)
[ 633.927649] sd 8:0:0:0: [sdg] Write Protect is off
[ 633.927664] sd 8:0:0:0: [sdg] Mode Sense: 4b 00 00 08
[ 633.928382] sd 8:0:0:0: [sdg] No Caching mode page present
[ 633.928396] sd 8:0:0:0: [sdg] Assuming drive cache: write through
[ 664.284502] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 695.338205] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 726.365266] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 757.285811] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 757.615136] sd 8:0:0:0: [sdg] No Caching mode page present
[ 757.615150] sd 8:0:0:0: [sdg] Assuming drive cache: write through
[ 788.259546] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 819.233339] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 850.260377] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 881.180880] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 881.510033] sdg: sdg1
[ 881.512872] sd 8:0:0:0: [sdg] No Caching mode page present
[ 881.512887] sd 8:0:0:0: [sdg] Assuming drive cache: write through
[ 912.207914] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 943.234923] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 974.155530] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 1005.182620] usb 1-2: reset high-speed USB device number 5 using ehci-pci
[ 1005.510025] sd 8:0:0:0: [sdg] Attached SCSI removable disk

When I plug in a Western Digital USB drive it is recognised and I can mount it through dolphin or the command line without problem.

I read this card earlier in the day and now it does not work on this pc!

HELP!

Simon.

Last edited by diesel1 (2013-07-31 01:24:04)

diesel1 · 2013-07-31 20:08:09

After leaving the card in the reader for an hour or so it showed up as available in Dolphin. It read fine and unmounted cleanly.

Another card also took around 15 minutes before it showed on the system as mountable.

Are there any ways of tracing what is happening? Any commands that will divulge pertinent information?

Simon.

kalithlev · 2013-08-03 11:48:27

I have the same problem with a USB card:

aug. 03 13:35:51 thor kernel: usb 4-1.2: new high-speed USB device number 13 using ehci-pci
aug. 03 13:35:51 thor kernel: usb-storage 4-1.2:1.0: USB Mass Storage device detected
aug. 03 13:35:51 thor kernel: scsi11 : usb-storage 4-1.2:1.0
aug. 03 13:35:51 thor mtp-probe[10673]: checking bus 4, device 13: "/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2"
aug. 03 13:35:51 thor mtp-probe[10673]: bus: 4, device: 13 was not an MTP device
aug. 03 13:35:53 thor kernel: scsi 11:0:0:0: Direct-Access sky USB 1.00 PQ: 0 ANSI: 4
aug. 03 13:35:53 thor kernel: sd 11:0:0:0: [sdb] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
aug. 03 13:35:53 thor kernel: sd 11:0:0:0: [sdb] Write Protect is off
aug. 03 13:35:53 thor kernel: sd 11:0:0:0: [sdb] Mode Sense: 2f 00 00 00
aug. 03 13:35:53 thor kernel: sd 11:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
aug. 03 13:36:24 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:36:55 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:37:26 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:37:57 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:38:28 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:38:59 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:39:31 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:40:02 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:40:02 thor kernel: sdb: sdb1
aug. 03 13:40:32 thor systemd-udevd[147]: worker [10752] /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/host11/targ...kill it
aug. 03 13:40:32 thor systemd-udevd[147]: seq 2769 '/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/host11/target11:... killed
aug. 03 13:40:32 thor systemd-udevd[147]: worker [10752] terminated by signal 9 (Killed)
aug. 03 13:40:33 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:41:02 thor systemd-udevd[147]: worker [10754] /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/host11/targ...kill it
aug. 03 13:41:02 thor systemd-udevd[147]: seq 2770 '/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/host11/target11:... killed
aug. 03 13:41:04 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:41:35 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:42:06 thor kernel: usb 4-1.2: reset high-speed USB device number 13 using ehci-pci
aug. 03 13:42:06 thor kernel: sd 11:0:0:0: [sdb] Attached SCSI removable disk
aug. 03 13:42:06 thor systemd-udevd[147]: worker [10754] terminated by signal 9 (Killed)

rasertux · 2013-08-03 12:37:06

I have the same problem and i found this https://bugs.archlinux.org/task/36296
Downgrade the Kernel to 3.10.2 make work again.

kalithlev · 2013-08-03 12:40:05

Thank you, I'll try downgrading.

Arch Linux

#1 2013-07-31 01:23:20

SDHC card will not mount.

#2 2013-07-31 20:08:09

Re: SDHC card will not mount.

#3 2013-08-03 11:48:27

Re: SDHC card will not mount.

#4 2013-08-03 12:37:06

Re: SDHC card will not mount.

#5 2013-08-03 12:40:05

Re: SDHC card will not mount.

Board footer