You are not logged in.
I was installing arch on a toshiba laptop with a "GeForce GT 740M" graphics adapter, what i found weird is that lspci listed the adapter as 3D controller (rather than the usual VGA compatible controller)
here is a paste of the last 100 lines in Xorg.1.log
I run
startxthen after GLX loads i think everything just freezes. (before this i had the no screens error)
Here is my /etc/X11/xorg.conf.d/20-nvidia.conf
Section "Device"
Identifier "GeForce GT 740m"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BusID "PCI:1:0:0"
EndSection(that is the correct Bus ID, before i wrote in the BusID i continued getting screen not found, usually on nvidia computers i have been able to get away with writing just the identifier and driver.)
This is irrelevant to window manager, (I've tried both kwin and openbox with same result)
I have not tried starting X with nouveau or the intel intergrated card yet.
Last edited by rabcor (2013-08-31 22:45:12)
Offline
Nobody has a clue what's going on? Or just knows how i could find out?
Last edited by rabcor (2013-08-31 00:26:51)
Offline
Which exact version of the drivers do you have installed? extra/nvidia, extra/nvidia-304xx/[AUR]/[nVidia Website]
Which kernel and what version are you using?
I take it you've configured it as explained here?
EDIT: Did this happen after an update, or has it been like this since installation? If it happened after an update, can you tell us which packages were updated?
Note: Please don't bump posts like that unless you have more information for us.
Last edited by clfarron4 (2013-08-31 02:50:44)
Claire is fine.
Problems? I have dysgraphia, so clear and concise please.
My public GPG key for package signing
My x86_64 package repository
Offline
You may want to try adding the Monitor, Screen, and possibly ServerLayout sections as well. I had to have all to get nVidia working previously. Although, I think it works without it now, but there's no harm in it just sitting around.
**EDIT**
I didn't initially notice the GLX part; my eyes locked onto the "no screens found" error. Sorry for the noise.
Last edited by skottish (2013-08-31 18:59:12)
Offline
I am having the same problem. X started normally until I updated this morning, then X failed after loading GLX. I simply re-installed the old kernel (linux 3.10.9-1), and the problem disappeared (i.e. X started normally). So it appears to be a bug with the latest kernel, relating to the video driver, as I have a laptop with a different driver (intel as opposed to NVidia), and had no problem with the update.
Offline
Offline
I installed extra/nvidia from the official repositories.
I followed the minimal configuration guide in here but that was not enough and i had to add the bus ID to make X detect the card.
This happened on the first setup and if i recall correctly that was kernel 3.10.9-1. No update had been performed.
Sorry for the bump but i posted it a week ago and wanted to make sure nobody had any thoughts before i'd just let it die.
I'm gonna be checking if i can solve this now tonight all the things you've said in here have been helpful and noted so i'll try them. I'll post further updates here in a few hours most likely (i'll be testing nouveau and the nvidia beta drivers, i'll be updating the system, and if all of that fails i'll see how it responds to the intel iGPU.)
Last edited by rabcor (2013-08-31 19:50:00)
Offline
I tried nouveau with no luck, i could never get it to detect any screens no matter how hard i tried.
I tried installing the drivers from hoome's thread too, no difference.
I tried switching to the Intel drivers and everything worked fine, what's weird is that X11 loads and seems to run, it detects a screen and everything (but not unless i add a Bus ID) but everything freezes.
Setting mode "nvidia-auto-select"
Failed to initiate mode change
Failed to complete mode change
ACPI: Failed to connect to the ACPI event daemon;
...These were the only nvidia related errors i found at a glance in the xorg.0 logfile.
I got rid of the acpi error by installing and enabling acpid
I've still got no clue about the mode change error.
Let me repeat again, Xorg loads, but the screen just freezes up before it loads (i can still change to other terminal windows though)
I just found out it uses this so called optimus technology i'm quite unfamiliar with.
Last edited by rabcor (2013-08-31 22:18:49)
Offline
Just one question. Is your Toshiba just running a nVidia GeForce 740M or is it a nVidia GeForce 740M with Optimus (that is it will have a second card, most probably an Intel Integrated Graphics chip of some sort)?
They are two very different things.
EDIT: Whilst I am at it could you post the output of lspci | grep VGA and lspci | grep 3D please?
Last edited by clfarron4 (2013-08-31 22:14:52)
Claire is fine.
Problems? I have dysgraphia, so clear and concise please.
My public GPG key for package signing
My x86_64 package repository
Offline
It uses 740m with optimus and it also has an intel intergrated chip with it.
VGA will list the intel card
3D will list the 740M card.
so this optimus thing basically means i can't run X from my nvidia card? ![]()
Offline
It means you need to read about Bumblebee.
Offline
I thought it might have been this as soon as you said that the Intel drivers could start X...
Basically, what is going on is that without something extra like Bumblebee, both cards will be turned on, but you will only be able to use the Intel card.
I suggest that you go with the Intel/nVidia option given in the link I just gave, because I doubt the nouveau drivers actually work with the 740M.
EDIT: That second paragraph is not quite true... If you can turn off the Intel card in the BIOS/EFI settings, then you can use the nVidia card as if the Intel card didn't exist (thus you can then install and run the nVidia drivers as if you only had an nVidia card). If you do this, then you will have to make sure the Intel card is turned off in the BIOS/EFI before you boot up ArchLinux.
Last edited by clfarron4 (2013-08-31 22:34:53)
Claire is fine.
Problems? I have dysgraphia, so clear and concise please.
My public GPG key for package signing
My x86_64 package repository
Offline
Turns out i can't disable the intel card in the bios.
sadly.
Thanks for your help guys!
Offline