You are not logged in.
I'm trying to get three displays running on my system. My system is Haswell bridge-based, which is supposed to support three displays without an add-on graphics card. My motherboard (Gigabyte GA-Z87N-WIFI) has two HDMI, one DVI outputs. The DVI and one of the HDMI outputs worked without messing with any configuration except KDE's system settings, where I just had to tell KDE where the two displays were placed.
The third display is trickier. In KDE's system settings, I can see that there's a third display connected, but nothing happens when I try to enable it.
So I switched to the command line and tried xrandr. Running xrandr with no arguments, I get the following output:
Screen 0: minimum 320 x 200, current 3840 x 1080, maximum 32767 x 32767
VGA1 disconnected (normal left inverted right x axis y axis)
HDMI1 connected primary 1920x1080+1920+0 (normal left inverted right x axis y axis) 476mm x 267mm
1920x1080 60.0*+ 50.0
1920x1080i 50.0 60.1
1280x1024 75.0 60.0
1152x864 75.0
1280x720 50.0 60.0
1440x576i 50.1
1024x768 75.1 60.0
1440x480i 60.1
800x600 75.0 60.3
720x576 50.0
720x480 59.9
640x480 75.0 60.0 59.9
720x400 70.1
DP1 disconnected (normal left inverted right x axis y axis)
HDMI2 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 476mm x 267mm
1920x1080 60.0*+ 50.0
1920x1080i 50.0 60.1
1280x1024 75.0 60.0
1152x864 75.0
1280x720 50.0 60.0
1440x576i 50.1
1024x768 75.1 60.0
1440x480i 60.1
800x600 75.0 60.3
720x576 50.0
720x480 59.9
640x480 75.0 60.0 59.9
720x400 70.1
DP2 disconnected (normal left inverted right x axis y axis)
HDMI3 connected (normal left inverted right x axis y axis)
1920x1080 60.0 + 50.0
1920x1080i 50.0 60.1
1280x1024 75.0 60.0
1152x864 75.0
1280x720 50.0 60.0
1440x576i 50.1
1024x768 75.1 60.0
1440x480i 60.1
800x600 75.0 60.3
720x576 50.0
720x480 59.9
640x480 75.0 60.0 59.9
720x400 70.1
DP3 disconnected (normal left inverted right x axis y axis)HDMI1 is actually a DVI connector, HDMI3 is the one that isn't working. When I run:
xrandr --output HDMI3 --mode 1920x1080 --right-of HDMI1 --verboseEverything goes black momentarily, then I get only HDMI1 and HDMI2 still, and the following output:
screen 0: 5760x1080 1520x285 mm 96.25dpi
crtc 2: 1920x1080 60.0 +3840+0 "HDMI3"
xrandr: Configure crtc 2 failed
crtc 0: disable
crtc 1: disable
crtc 2: disable
screen 0: revert
crtc 0: revert
crtc 1: revert
crtc 2: revertAfter this, these lines have appeared in Xorg.0.log:
[ 1466.250] (II) intel(0): resizing framebuffer to 5760x1080
[ 1466.250] (II) intel(0): switch to mode 1920x1080@60.0 on pipe 0 using HDMI1, position (1920, 0), rotation normal
[ 1466.309] (II) intel(0): switch to mode 1920x1080@60.0 on pipe 1 using HDMI2, position (0, 0), rotation normal
[ 1466.332] (II) intel(0): switch to mode 1920x1080@60.0 on pipe 2 using HDMI3, position (3840, 0), rotation normal
[ 1466.332] (EE) intel(0): failed to set mode: Invalid argument
[ 1466.397] (II) intel(0): resizing framebuffer to 3840x1080
[ 1466.408] (II) intel(0): switch to mode 1920x1080@60.0 on pipe 0 using HDMI1, position (1920, 0), rotation normal
[ 1466.637] (II) intel(0): switch to mode 1920x1080@60.0 on pipe 1 using HDMI2, position (0, 0), rotation normalI'm at a loss. Has anyone seen this before? Do I need to use something other than xrandr? I've used Xinerama before, but only with two displays.
Offline
The GA-Z87N-WIFI manual suggests that simultaneous triple monitor should work, but perhaps it doesn't. The error message sounds a lot like the typical "only 2 PLLs" problem. See https://bugzilla.redhat.com/show_bug.cgi?id=836765 and https://en.wikipedia.org/wiki/Intel_HD_ … e_displays
Can you get the third output working if you disable one of the others? ie. the output is working but you just can't enable all three at the same time? Suggest opening a bug on freedesktop.org.
Offline
I'm having the exact same problem. Before I upgraded a couple of things my 3 displays worked and now they don't.
Last edited by cpcloud (2013-09-19 04:53:08)
Offline
Offline
[HSW] wrpll sharing not implemented - https://bugs.freedesktop.org/show_bug.cgi?id=68485
Jessica 2013-09-06 23:03:23 UTC
I've got the same problem (slightly different board: GA-Z87N-WIFI, but with 2x HDMI, 1x DVI). The symptoms seem to be the same, though I'm running a slightly different kernel (3.10.7).I'm running Arch
Mateusz Kwiatkowski 2013-09-17 14:21:27 UTC
I have Intel graphics card and it supports triple head setup very well. My setup is...I updated kernel to 3.11.1 after it appeared in Archlinux's repo and one of screens stopped working.
Offline