Arch Linux

fawaz

Member

Registered: 2013-09-21

Posts: 2

mkinitcpio fglrx hook

I recently installed the proprietary amd drivers and a new hook was placed in my mkinitcpio. Is it safe to remove the hook and what does it do?

# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run.  Advanced users may wish to specify all system modules
# in this array.  For instance:
#     MODULES="piix ide_disk reiserfs"
MODULES="ahci sd_mod ext4"

# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image.  This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES="fsck fsck.ext4"

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way.  This is useful for config files.
FILES=""

# HOOKS
# This is the most important setting in this file.  The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
##   This setup specifies all modules in the MODULES setting above.
##   No raid, lvm2, or encrypted root is needed.
#    HOOKS="base"
#
##   This setup will autodetect all modules for your system and should
##   work as a sane default
#    HOOKS="base udev autodetect block filesystems"
#
##   This setup will generate a 'full' image which supports most systems.
##   No autodetection is done.
#    HOOKS="base udev block filesystems"
#
##   This setup assembles a pata mdadm array with an encrypted root FS.
##   Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
#    HOOKS="base udev block mdadm encrypt filesystems"
#
##   This setup loads an lvm2 volume group on a usb device.
#    HOOKS="base udev block lvm2 filesystems"
#
##   NOTE: If you have /usr on a separate partition, you MUST include the
#    usr, fsck and shutdown hooks.
HOOKS="base modconf fglrx"

# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
COMPRESSION=cat
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"

# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""

Last edited by fawaz (2013-09-21 15:26:30)

kaszak696

Member

Registered: 2009-05-26

Posts: 543

Re: mkinitcpio fglrx hook

It's not functional anymore, catalyst-hook now uses systemd unit instead. See this.

---

'What can be asserted without evidence can also be dismissed without evidence.' - Christopher Hitchens
'There's no such thing as addiction, there's only things that you enjoy doing more than life.' - Doug Stanhope
GitHub Junkyard

fawaz

Member

Registered: 2013-09-21

Posts: 2

Re: mkinitcpio fglrx hook

When i updated my mkinitcpio systemd-remount-fs.service started(never used to start) and its dramtically increased my boot time.

Last edited by fawaz (2013-09-21 15:25:43)