You are not logged in.

#1 2006-01-06 14:14:29

Stalwart
Member
From: Latvia, Riga
Registered: 2005-10-18
Posts: 445
Website

SiS USB 2.0

On my desktop box i get 2-3 Mb/s when i copy files to usb-drive. On SIS-based lappy all i get is 47 kb/s sad Where can be problem?

[stalwart@fuaran ~]$ lshwd
00:00.0 Host bridge: Silicon Integrated System|Host-to-PCI Bridge (sis-agp)
00:01.0 PCI bridge: Silicon Integrated System|SiS648FX Virtual PCI to PCI Bridge (AGP) (unknown)
00:02.0 ISA bridge: Silicon Integrated System|SiS963 PCI to ISA Bridge (unknown)
00:02.1 SMBus: Silicon Integrated System|SiS961/962 SMBus Controller (i2c-sis96x)
00:02.5 IDE interface: Silicon Integrated Systems [SiS]|5513 [IDE] (sis5513)
00:02.6 Modem: Silicon Integrated System|SiS7013 56k Modem (slamr)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]|SiS7012 PCI Audio Accelerator (snd-intel8x0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS]|7001 USB (ohci_hcd)
00:03.1 USB Controller: Silicon Integrated Systems [SiS]|7001 USB (ohci_hcd)
00:03.3 USB Controller: Silicon Integrated Systems [SiS]|7002 USB 2.0 Controller (ehci-hcd)
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS]|SiS900 10/100 Ethernet (sis900)
00:06.0 CardBus bridge: Texas Instruments|PCI1410 PC card Cardbus Controller (yenta_socket)
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]|SiS Real256E (sis)
003:001 USB Hub: Virtual|Hub (unknown)
002:001 USB Hub: Virtual|Hub (unknown)
001:001 USB Hub: Virtual|Hub (unknown)
[stalwart@fuaran ~]$ dmesg | grep usb
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver usb-storage
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usb 2-3: new full speed USB device using ohci_hcd and address 2
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb 2-3: USB disconnect, address 2


IRC: Stalwart @ FreeNode
Skype ID: thestalwart
WeeChat-devel nightly packages for i686

Offline

#2 2006-01-06 15:29:39

tpowa
Developer
From: Lauingen , Germany
Registered: 2004-04-05
Posts: 2,322

Re: SiS USB 2.0

don't use ehci module on it, on mine usb2 is horrible broken too.
add ehci-hcd to blacklist in rc.conf. you will get only usb1 but this is better then a broken usb2 connect.

Offline

#3 2006-01-06 17:27:49

Stalwart
Member
From: Latvia, Riga
Registered: 2005-10-18
Posts: 445
Website

Re: SiS USB 2.0

It was 47 kb/s, now i got 48 kb/s :? Any ways to make it faster? sad


IRC: Stalwart @ FreeNode
Skype ID: thestalwart
WeeChat-devel nightly packages for i686

Offline

Board footer

Powered by FluxBB