You are not logged in.
A few years ago I was using a Logitech MX1000 and configured my system to turn the center thumb button into the middle click action, and disable the true scroll wheel button. I have recently replaced my MX1000 with an M570 which does not have the extra thumb button, so I want to get my scroll button back to normal, but I cannot for the life of me remember how I set up the remapping. I've checked my xorg.conf, .xinitrc, .xbindkeysrc (all pasted below) and can't find anything relevent.
When I run xev and press the scroll wheel button, it reports button 10 has been pressed (I believe that this was the extra side button on the MX1000). I found this article (https://wiki.archlinux.org/index.php/Logitech_MX1000), but the only reference to button 10 is that it can be remapped like the rest using .xbindkeysrc, which it seems I have not done.
Any other ideas for places to look for undoing this remapping would be greatly appreciated.
/etc/X11/xorg.confSection "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Evdev Mouse" "CorePointer"
EndSection
Section "Module"
EndSection
Section "InputDevice"
Identifier "Evdev Mouse"
Driver "evdev"
Option "Name" "Logitech USB Receiver"
Option "CorePointer"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "0-DFP11"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "PreferredMode" "2560x1440"
Option "TargetRefresh" "60"
Option "Position" "1920 0"
Option "Rotate" "normal"
Option "Disable" "false"
EndSection
Section "Monitor"
Identifier "0-DFP10"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
Option "Position" "0 357"
Option "Rotate" "normal"
Option "Disable" "false"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
Option "Monitor-DFP11" "0-DFP11"
Option "Monitor-DFP10" "0-DFP10"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Virtual 4480 2560
Depth 24
EndSubSection
EndSection~/.xbindkeysrc# Mouse Buttons
"/usr/bin/xvkbd -xsendevent -text "\[Alt_L]\[Left]""
m:0x0 + b:8
"/usr/bin/xvkbd -xsendevent -text "\[Alt_L]\[Right]""
m:0x0 + b:9
#"/usr/bin/xvkbd -xsendevent -text "\[Up]""
"/usr/bin/xvkbd -xsendevent -text "\[Page_Up]""
m:0x0 + b:11
#"/usr/bin/xvkbd -xsendevent -text "\[Down]""
"/usr/bin/xvkbd -xsendevent -text "\[Page_Down]""
m:0x0 + b:12~/.xinitrcexec ck-launch-session gnome-session
% xbindkeysOffline
Naturally, less than a minute after I press "Submit" on my question, I find my own solution. I had remapped the button in
/etc/X11/Xmodmap.
! MX1000
pointer = 1 10 3 4 5 6 7 8 9 2 11 12 13 14As you can see, 2 and 10 were swapped. now, if there is a way that I can remap each mouse independantly, that would be useful (though the MX1000 doesn't see much use these days).
Offline