You are not logged in.

Pages: 1 2

#1 2006-01-22 23:08:04

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Hi,

I have an older T22 Thinkpad.  I installed 0.7.1, and upgraded xorg from testing.  I've rerun xorgconfig, and identified the savage driver, and limited the configuration to the 8mb of RAM on the laptop.

When I startx, using TWM, I can get windows to appear, and I can run some basic applications.  When I run KDE, it goes through the initialization, then the screen goes black, and I have a cursor on the desktop.  Nothing else.

Gnome stops on the initialization screen.

I've checked the xorg.0.log, and there is one error about not being able to address a non-exisitant TTY0.  I checked the logs on my PCs that are functioning well, and this seems to come up in all my logs, so I haven't worried about that.

The only other note is from the savage drivers about not loading drx (which I have left commented out; my board doesn't have enough memory). 

I've set some pretty basic horizontal and vertical refresh rates.  I've also tried the plain jane VGA drivers but those don't work at all.

I've booted to Knoppix (didn't check the x configuration, hmmm), and KDE runs ok with that.

I've also googled "T22 xorg" and haven't discovered much of any use.

Can one of the wizars perhaps offer me some additional advice or additional debugging tips?  I'd sure appreciate it!

Kind regards.

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#2 2006-01-22 23:44:20

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

FYI, wmaker seems also to work pretty well.  Just a problem with rendering on KDE and gnome...

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#3 2006-01-23 14:06:53

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

This question doesn't seem to be generaring much momentum :->

Is there additional information I can offer, or would it be better posted somewhere else?

Thx in advance!

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#4 2006-01-25 13:54:27

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Some folks were kind enough to send me copies of the xorg config files.  I reinstalled and re-ran xorgconifg and made sure that I had no more than 1024x768 as a resoultion and things are OK.

I thought I'd tried that before, but perhaps not.

At any rate, thx for those who considered my question.

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#5 2006-06-29 18:31:51

zaterio
Member
Registered: 2006-05-21
Posts: 23

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Hi my video in my thinkpad works fine (DRI works):
l

lspci:

00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
00:03.0 Communication controller: Agere Systems WinModem 56k (rev 01)
00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
01:00.0 VGA compatible controller: S3 Inc. 86C270-294 Savage/IX-MV (rev 13)
[root@zaterio ~]#


My xorg.conf:


Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
    RgbPath      "/usr/share/X11/rgb"
    ModulePath   "/usr/lib/xorg/modules"
    FontPath     "/usr/share/fonts/misc"
    FontPath     "/usr/share/fonts/75dpi"
    FontPath     "/usr/share/fonts/100dpi"
    FontPath     "/usr/share/fonts/TTF"
    FontPath     "/usr/share/fonts/Type1"
    FontPath     "/usr/local/share/fonts"
EndSection

Section "Module"
    Load  "extmod"
    Load  "dbe"
    Load  "record"
    Load  "xtrap"
    Load  "dri"
    Load  "glx"
    Load  "freetype"
    Load  "type1"
EndSection

Section "DRI"
    Mode 0666
    EndSection

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
EndSection

Section "InputDevice"
    Identifier  "Mouse0"
    Driver      "mouse"
    Option        "Protocol" "auto"
    Option        "Device" "/dev/input/mice"
    Option        "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
    Identifier   "Monitor0"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "ShadowFB"               # [<bool>]
        #Option     "DefaultRefresh"         # [<bool>]
        #Option     "ModeSetClearScreen"     # [<bool>]
    Identifier  "Card0"
    Driver      "vesa"
    VendorName  "S3 Inc."
    BoardName   "86C270-294 Savage/IX-MV"
    BusID       "PCI:1:0:0"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    SubSection "Display"
        Viewport   0 0
        Depth     1
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
EndSection


before of use this xorg.conf you need to install the apropiatte dri and vesa drivers

Offline

#6 2006-06-29 18:33:21

zaterio
Member
Registered: 2006-05-21
Posts: 23

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

is a thinkpad T22 i forget says that

Offline

#7 2006-06-29 19:42:42

Gullible Jones
Member
Registered: 2004-12-29
Posts: 4,863

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

You need to change "vesa" in the Device section to "savage", and install xf86-video-savage.

Offline

#8 2006-06-29 20:22:56

zaterio
Member
Registered: 2006-05-21
Posts: 23

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Gullible Jones wrote:

You need to change "vesa" in the Device section to "savage", and install xf86-video-savage.

Thanks

but I try tis option, but for me works better the vesa driver with dri

Offline

#9 2006-06-30 03:11:42

iphitus
Forum Fellow
From: Melbourne, Australia
Registered: 2004-10-09
Posts: 4,927

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

zaterio wrote:
Gullible Jones wrote:

You need to change "vesa" in the Device section to "savage", and install xf86-video-savage.

Thanks

but I try tis option, but for me works better the vesa driver with dri

vesa does not provide direct rendering. if you want it, then you need the proper savage driver.

Offline

#10 2006-06-30 13:08:00

Gullible Jones
Member
Registered: 2004-12-29
Posts: 4,863

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

zaterio wrote:
Gullible Jones wrote:

You need to change "vesa" in the Device section to "savage", and install xf86-video-savage.

Thanks

but I try tis option, but for me works better the vesa driver with dri

What do you mean by that? Does part of the image shift off the screen no matter you adjust the monitor, or somesuch? Does X hang up and give you a blank screen?

Offline

#11 2006-06-30 15:20:21

zaterio
Member
Registered: 2006-05-21
Posts: 23

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

with the vesa driver (no dri configuration in xorg.conf) the size of screen is ok but when i move a window lokks very bad, with the dri option and vesa driver in xorg.cong i have no problem everithing lokks y fells good
with the savage driver i get a wrong screnn size (more litle the image than the real screnn size) and with the dri option enabled in the xorg.conf the screnn goes black, and i need to restart with a live-cd and fix the problem...maybe vesa with dri dont work but for me works and my system looks nice..

cheers

zaterio

Offline

#12 2006-06-30 15:39:31

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

I am using the savage drivers now on this T22.  No dri module, screen depth 24 at 1024x768 resolution.  This seems to work very well for me.

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#13 2006-06-30 15:49:57

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Just for fun, I enabled the dri module.  Seems to work just fine on this T22.

Kind regards.

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#14 2006-06-30 15:50:48

Gullible Jones
Member
Registered: 2004-12-29
Posts: 4,863

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

If you get screen size problems try putting

Option "UseBIOS" "false"

In your "Device" section.

(I *think* ddc will allow this to work without you putting in any modelines.)

Offline

#15 2006-06-30 19:04:31

zaterio
Member
Registered: 2006-05-21
Posts: 23

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Gullible Jones wrote:

If you get screen size problems try putting

Option "UseBIOS" "false"

In your "Device" section.

(I *think* ddc will allow this to work without you putting in any modelines.)

I try this option, but the screen still goes black, my xorg.conf:

Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
    RgbPath      "/usr/share/X11/rgb"
    ModulePath   "/usr/lib/xorg/modules"
    FontPath     "/usr/share/fonts/misc"
    FontPath     "/usr/share/fonts/75dpi"
    FontPath     "/usr/share/fonts/100dpi"
    FontPath     "/usr/share/fonts/TTF"
    FontPath     "/usr/share/fonts/Type1"
    FontPath     "/usr/local/share/fonts"
EndSection

Section "Module"
    Load  "extmod"
    Load  "dbe"
    Load  "record"
    Load  "xtrap"
    Load  "dri"
    Load  "glx"
    Load  "freetype"
    Load  "type1"
EndSection

Section "DRI"
    Mode 0666
    EndSection

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
EndSection

Section "InputDevice"
    Identifier  "Mouse0"
    Driver      "mouse"
    Option        "Protocol" "auto"
    Option        "Device" "/dev/input/mice"
    Option        "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
    Identifier   "Monitor0"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "ShadowFB"               # [<bool>]
        #Option     "DefaultRefresh"         # [<bool>]
        #Option     "ModeSetClearScreen"     # [<bool>]
    Identifier  "Card0"
    Driver      "savage"
    VendorName  "S3 Inc."
    BoardName   "86C270-294 Savage/IX-MV"
    BusID       "PCI:1:0:0"
Option "UseBIOS" "false"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    SubSection "Display"
        Viewport   0 0
        Depth     1
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
        Modes        "1024x768" "800x600" "640x480"
    EndSubSection
EndSection

Offline

#16 2006-06-30 19:18:04

Gullible Jones
Member
Registered: 2004-12-29
Posts: 4,863

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Hmmm... Try putting

Option     "IgnoreEDID" "false"

In the "Display" subsection that you're currently using. If that doesn't work, set it to "true".

Offline

#17 2006-07-01 00:54:24

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

zaterio -

I'd be happy to send you my xorg.conf, or post it here if you want.  I don't want to just stick it here without knowing first that it will be of some value.  I do have dri loaded, no problems with screen sizes.

Kind regards.

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#18 2006-07-01 03:36:11

Gullible Jones
Member
Registered: 2004-12-29
Posts: 4,863

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

desertViking wrote:

zaterio -

I'd be happy to send you my xorg.conf, or post it here if you want.  I don't want to just stick it here without knowing first that it will be of some value.  I do have dri loaded, no problems with screen sizes.

Kind regards.

Wait, you got it solved? Could you post the working xorg.conf on this thread?

Offline

#19 2006-07-01 03:54:02

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Sure, I hope it's useful.
I am upgraded to "testing".
This is the xorg.conf I'm using on this T22.  I *believe* I generated this using xorgconfig.  I've snipped some of the stuff that I thought was irrelevant (input, paths and such).  I tried to leave the things that were related to the monitor and video card.

<removed>

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#20 2006-07-01 19:31:52

zaterio
Member
Registered: 2006-05-21
Posts: 23

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Thanks, i have no time now for try the xorg.conf, when i put the xorg file in my T22 i will answer here

thanks a lot

zaterio

Offline

#21 2006-07-01 20:53:41

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

That's cool.  Just note that this is just a snipet from my xorg file.  If you want the whole thing let me know.

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#22 2006-07-01 21:29:02

zaterio
Member
Registered: 2006-05-21
Posts: 23

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

desertViking wrote:

That's cool.  Just note that this is just a snipet from my xorg file.  If you want the whole thing let me know.

ahh ok, can you post here your entire xorg.conf ? i will apreciatte that

thank you in advanced

zaterio

Offline

#23 2006-07-02 15:34:02

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Here's the whole thing. I believe it was generated by xorgconfig.

<snipped>

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

#24 2006-07-02 16:00:41

Gullible Jones
Member
Registered: 2004-12-29
Posts: 4,863

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

The DRI section should be uncommented if you want DRI as a normal user.

(BTW, have either of you tried using 'X -configure'? That specifies a lot more modules to be loaded, and seems to autodetect a lot of stuff.)

Offline

#25 2006-07-02 16:52:39

desertViking
Member
From: Arizona
Registered: 2005-10-30
Posts: 170

Re: Thinkpad T22 w/Xorg7 and Savage drivers - no rendering

Gullible Jones wrote:

The DRI section should be uncommented if you want DRI as a normal user.

Correct as usual!  I uncommented the DRI section at the end, restarted (it's still golden), and am including it here.  I've deleted my other inserts to avoid confusion:

# File generated by xorgconfig.

#
# Copyright 2004 The X.Org Foundation
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
# 
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# 
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
# 
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
#

# **********************************************************************
# Refer to the xorg.conf(5x) man page for details about the format of 
# this file.
# **********************************************************************

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"      # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
#    Load        "type1"
#    Load        "speedo"
    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
#    Load       "glx"
# This loads the DRI module
    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath    "/usr/share/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# 

    FontPath   "/usr/share/fonts/misc"
    FontPath   "/usr/share/fonts/75dpi"
    FontPath   "/usr/share/fonts/100dpi"
    FontPath   "/usr/share/fonts/TTF"
    FontPath   "/usr/share/fonts/Type1"
#    FontPath   "/usr/lib/X11/fonts/local/"
#    FontPath   "/usr/lib/X11/fonts/misc/"
#    FontPath   "/usr/lib/X11/fonts/75dpi/:unscaled"
#    FontPath   "/usr/lib/X11/fonts/100dpi/:unscaled"
#    FontPath   "/usr/lib/X11/fonts/Speedo/"
#    FontPath   "/usr/lib/X11/fonts/Type1/"
#    FontPath   "/usr/lib/X11/fonts/TrueType/"
#    FontPath   "/usr/lib/X11/fonts/freefont/"
#    FontPath   "/usr/lib/X11/fonts/75dpi/"
#    FontPath   "/usr/lib/X11/fonts/100dpi/"

# The module search path.  The default path is shown here.

     ModulePath "/usr/lib/xorg/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Ctrl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Ctrl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Ctrl><Alt><KP_>/<KP_> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client. 

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings. 

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier    "Keyboard1"
    Driver    "kbd"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option    "Xleds"      "1 2 3"

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc105"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"   "de"
# or:
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"

# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc105"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules"    "xorg"
    Option "XkbModel"    "pc101"
    Option "XkbLayout"    "us"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier    "Mouse1"
    Driver    "mouse"
    Option "Protocol"    "Auto"    # Auto detect
    Option "Device"      "/dev/input/mice"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"    "Xqueue"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution"    "256"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"    "9600"
#    Option "SampleRate"    "150"

# Mouse wheel mapping.  Default is to map vertical wheel to buttons 4 & 5,
# horizontal wheel to buttons 6 & 7.   Change if your mouse has more than
# 3 buttons and you need to map the wheel to different button ids to avoid
# conflicts.

    Option "ZAxisMapping"   "4 5 6 7"

# Emulate3Buttons is an option for 2-button mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections 
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice" 
#    Identifier  "Mouse2"
#    Driver      "mouse"
#    Option      "Protocol"      "MouseMan"
#    Option      "Device"        "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "1412"
#    Option     "MaxX"          "15184"
#    Option     "MinY"          "15372"
#    Option     "MaxY"          "1230"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "231"
#    Option     "MaxX"          "3868"
#    Option     "MinY"          "3858"
#    Option     "MaxY"          "272"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonThreshold"       "17"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "IBM Thinkpad"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   31.5 - 57.0

#    HorizSync    30-64         # multisync
#    HorizSync    31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync    15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-90
    Option      "DPMS"

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier    "Standard VGA"
    VendorName    "Unknown"
    BoardName    "Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset    "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10:0"

#    VideoRam    256

#    Clocks    25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
    Identifier  "IBM Thinkpad"
    Driver      "savage"
    #VideoRam    8192
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "IBM Thinkpad"
    Monitor     "IBM Thinkpad"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1152x864" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1152x864" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1152x864" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

Section "DRI"
    Mode 0666
EndSection

"In theory, there's no difference between theory and practice, but in practice there is."

Offline

Pages: 1 2

Board footer

Powered by FluxBB