You are not logged in.
- Topics: Active | Unanswered
Pages: 1
#1 2014-10-09 15:40:55
- GiBg1aN
- Member
- Registered: 2014-10-08
- Posts: 8
X Doesn't start(NVIDIA drivers)
I installed Arch a month ago with nouveau drivers, but the nvidia card didn't work(only the intel), so I decided to install proprietary drivers(I prefer they).
I have a GTX 850M so I installled nvidia-340xx package(am i wrong?) and xf86-video-modesetting as I have hybrid graphics, after that I put the following configuration in /etc/X11/xorg.conf.d/20-nvidia.conf
Section "ServerLayout"
Identifier "layout"
Screen 0 "nvidia"
Inactive "intel"
EndSection
Section "Device"
Identifier "nvidia"
Driver "nvidia"
BusID "PCI:PCI address determined earlier"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "nvidia"
Device "nvidia"
Option "AllowEmptyInitialConfiguration"
EndSection
Section "Device"
Identifier "intel"
Driver "modesetting"
EndSection
Section "Screen"
Identifier "intel"
Device "intel"
EndSectionI put nvidia module in mkinitcpio.conf but when after reboot i checked with lsmod, and it there wasn't it, so i tried to load it with modprobe:
[root@arch /]# modprobe nvidia
modprobe: ERROR: could not insert 'nvidia' : No such deviceAfter reboot gnome doesn't start, and X too, this is my Xorg.0.log:
[ 83.437]
X.Org X Server 1.16.1
Release Date: 2014-09-21
[ 83.437] X Protocol Version 11, Revision 0
[ 83.437] Build Operating System: Linux 3.16.1-1-ARCH x86_64
[ 83.437] Current Operating System: Linux arch 3.16.4-1-ARCH #1 SMP PREEMPT Mon Oct 6 08:22:27 CEST 2014 x86_64
[ 83.438] Kernel command line: initrd=\initramfs-linux.img root=/dev/sda5 rw quiet rcutree.rcu_idle_gp_delay=1 ipv6.disable_ipv6=1
[ 83.438] Build Date: 21 September 2014 10:53:13AM
[ 83.438]
[ 83.438] Current version of pixman: 0.32.6
[ 83.438] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 83.438] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 83.438] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Oct 9 16:32:54 2014
[ 83.438] (==) Using config file: "/etc/X11/xorg.conf"
[ 83.438] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 83.438] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 83.438] (==) ServerLayout "Layout0"
[ 83.438] (**) |-->Screen "Screen0" (0)
[ 83.438] (**) | |-->Monitor "Monitor0"
[ 83.438] (**) | |-->Device "Device0"
[ 83.438] (**) |-->Input Device "Keyboard0"
[ 83.438] (**) |-->Input Device "Mouse0"
[ 83.438] (==) Automatically adding devices
[ 83.438] (==) Automatically enabling devices
[ 83.438] (==) Automatically adding GPU devices
[ 83.438] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 83.438] Entry deleted from font path.
[ 83.438] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 83.438] Entry deleted from font path.
[ 83.438] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 83.438] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 83.438] Entry deleted from font path.
[ 83.438] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 83.438] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 83.438] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 83.438] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 83.438] (WW) Disabling Keyboard0
[ 83.438] (WW) Disabling Mouse0
[ 83.438] (II) Loader magic: 0x818d80
[ 83.438] (II) Module ABI versions:
[ 83.438] X.Org ANSI C Emulation: 0.4
[ 83.438] X.Org Video Driver: 18.0
[ 83.438] X.Org XInput driver : 21.0
[ 83.438] X.Org Server Extension : 8.0
[ 83.440] (II) systemd-logind: took control of session /org/freedesktop/login1/session/c1
[ 83.440] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 83.440] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 8 paused 0
[ 83.441] (--) PCI:*(0:0:2:0) 8086:0416:1558:6501 rev 6, Mem @ 0xf7400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f000/64
[ 83.441] (--) PCI: (0:1:0:0) 10de:1391:1558:6501 rev 162, Mem @ 0xf6000000/16777216, 0xe0000000/268435456, 0xf0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288
[ 83.441] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 83.441] (II) LoadModule: "glx"
[ 83.441] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 83.446] (II) Module glx: vendor="NVIDIA Corporation"
[ 83.446] compiled for 4.0.2, module version = 1.0.0
[ 83.446] Module class: X.Org Server Extension
[ 83.446] (II) NVIDIA GLX Module 304.123 Wed Jul 2 11:19:55 PDT 2014
[ 83.446] (II) LoadModule: "nvidia"
[ 83.446] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 83.446] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 83.446] compiled for 4.0.2, module version = 1.0.0
[ 83.446] Module class: X.Org Video Driver
[ 83.534] (EE) NVIDIA: Failed to load the NVIDIA kernel module. Please check your
[ 83.534] (EE) NVIDIA: system's kernel log for additional error messages.
[ 83.534] (II) UnloadModule: "nvidia"
[ 83.534] (II) Unloading nvidia
[ 83.534] (EE) Failed to load module "nvidia" (module-specific error, 0)
[ 83.534] (EE) No drivers available.
[ 83.535] (EE)
Fatal server error:
[ 83.535] (EE) no screens found(EE)
[ 83.535] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 83.535] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 83.535] (EE) and this is dmesg:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.16.4-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.1 20140903 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Oct 6 08:22:27 CEST 2014
[ 0.000000] Command line: initrd=\initramfs-linux.img root=/dev/sda5 rw quiet ipv6.disable_ipv6=1 rcutree.rcu_idle_gp_delay=1
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000059000-0x000000000009dfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000b8115fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000b8116000-0x00000000b811cfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000b811d000-0x00000000b894bfff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000b894c000-0x00000000b8bedfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000b8bee000-0x00000000c8c0afff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000c8c0b000-0x00000000c910afff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000c910b000-0x00000000c963afff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000c963b000-0x00000000c97aafff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000c97ab000-0x00000000c9ffefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000c9fff000-0x00000000c9ffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cb000000-0x00000000cf1fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000022fdfffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] e820: update [mem 0xb719e018-0xb71b7457] usable ==> usable
[ 0.000000] extended physical RAM map:
[ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x0000000000057fff] usable
[ 0.000000] reserve setup_data: [mem 0x0000000000058000-0x0000000000058fff] reserved
[ 0.000000] reserve setup_data: [mem 0x0000000000059000-0x000000000009dfff] usable
[ 0.000000] reserve setup_data: [mem 0x000000000009e000-0x000000000009ffff] reserved
[ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x00000000b719e017] usable
[ 0.000000] reserve setup_data: [mem 0x00000000b719e018-0x00000000b71b7457] usable
[ 0.000000] reserve setup_data: [mem 0x00000000b71b7458-0x00000000b8115fff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000b8116000-0x00000000b811cfff] ACPI NVS
[ 0.000000] reserve setup_data: [mem 0x00000000b811d000-0x00000000b894bfff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000b894c000-0x00000000b8bedfff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000b8bee000-0x00000000c8c0afff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000c8c0b000-0x00000000c910afff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000c910b000-0x00000000c963afff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000c963b000-0x00000000c97aafff] ACPI NVS
[ 0.000000] reserve setup_data: [mem 0x00000000c97ab000-0x00000000c9ffefff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000c9fff000-0x00000000c9ffffff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000cb000000-0x00000000cf1fffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000022fdfffff] usable
[ 0.000000] efi: EFI v2.31 by American Megatrends
[ 0.000000] efi: ACPI 2.0=0xc973f000 ACPI=0xc973f000 SMBIOS=0xc9f56598
[ 0.000000] efi: mem00: type=7, attr=0xf, range=[0x0000000000000000-0x0000000000001000) (0MB)
[ 0.000000] efi: mem01: type=2, attr=0xf, range=[0x0000000000001000-0x0000000000007000) (0MB)
[ 0.000000] efi: mem02: type=7, attr=0xf, range=[0x0000000000007000-0x0000000000058000) (0MB)
[ 0.000000] efi: mem03: type=0, attr=0xf, range=[0x0000000000058000-0x0000000000059000) (0MB)
[ 0.000000] efi: mem04: type=7, attr=0xf, range=[0x0000000000059000-0x000000000009e000) (0MB)
[ 0.000000] efi: mem05: type=0, attr=0xf, range=[0x000000000009e000-0x00000000000a0000) (0MB)
[ 0.000000] efi: mem06: type=7, attr=0xf, range=[0x0000000000100000-0x0000000001000000) (15MB)
[ 0.000000] efi: mem07: type=2, attr=0xf, range=[0x0000000001000000-0x0000000001f47000) (15MB)
[ 0.000000] efi: mem08: type=7, attr=0xf, range=[0x0000000001f47000-0x000000007f834000) (2008MB)
[ 0.000000] efi: mem09: type=2, attr=0xf, range=[0x000000007f834000-0x0000000080000000) (7MB)
[ 0.000000] efi: mem10: type=7, attr=0xf, range=[0x0000000080000000-0x00000000b4c0c000) (844MB)
[ 0.000000] efi: mem11: type=2, attr=0xf, range=[0x00000000b4c0c000-0x00000000b4d0c000) (1MB)
[ 0.000000] efi: mem12: type=7, attr=0xf, range=[0x00000000b4d0c000-0x00000000b719e000) (36MB)
[ 0.000000] efi: mem13: type=2, attr=0xf, range=[0x00000000b719e000-0x00000000b71b8000) (0MB)
[ 0.000000] efi: mem14: type=1, attr=0xf, range=[0x00000000b71b8000-0x00000000b8116000) (15MB)
[ 0.000000] efi: mem15: type=10, attr=0xf, range=[0x00000000b8116000-0x00000000b811d000) (0MB)
[ 0.000000] efi: mem16: type=4, attr=0xf, range=[0x00000000b811d000-0x00000000b826f000) (1MB)
[ 0.000000] efi: mem17: type=3, attr=0xf, range=[0x00000000b826f000-0x00000000b8912000) (6MB)
[ 0.000000] efi: mem18: type=4, attr=0xf, range=[0x00000000b8912000-0x00000000b8917000) (0MB)
[ 0.000000] efi: mem19: type=3, attr=0xf, range=[0x00000000b8917000-0x00000000b891b000) (0MB)
[ 0.000000] efi: mem20: type=4, attr=0xf, range=[0x00000000b891b000-0x00000000b8931000) (0MB)
[ 0.000000] efi: mem21: type=3, attr=0xf, range=[0x00000000b8931000-0x00000000b8943000) (0MB)
[ 0.000000] efi: mem22: type=4, attr=0xf, range=[0x00000000b8943000-0x00000000b894c000) (0MB)
[ 0.000000] efi: mem23: type=6, attr=0x800000000000000f, range=[0x00000000b894c000-0x00000000b8bee000) (2MB)
[ 0.000000] efi: mem24: type=4, attr=0xf, range=[0x00000000b8bee000-0x00000000b8bfc000) (0MB)
[ 0.000000] efi: mem25: type=7, attr=0xf, range=[0x00000000b8bfc000-0x00000000b8c06000) (0MB)
[ 0.000000] efi: mem26: type=2, attr=0xf, range=[0x00000000b8c06000-0x00000000b8c0b000) (0MB)
[ 0.000000] efi: mem27: type=7, attr=0xf, range=[0x00000000b8c0b000-0x00000000c5b1f000) (207MB)
[ 0.000000] efi: mem28: type=4, attr=0xf, range=[0x00000000c5b1f000-0x00000000c5c4d000) (1MB)
[ 0.000000] efi: mem29: type=7, attr=0xf, range=[0x00000000c5c4d000-0x00000000c5c99000) (0MB)
[ 0.000000] efi: mem30: type=4, attr=0xf, range=[0x00000000c5c99000-0x00000000c5cbd000) (0MB)
[ 0.000000] efi: mem31: type=7, attr=0xf, range=[0x00000000c5cbd000-0x00000000c5cc9000) (0MB)
[ 0.000000] efi: mem32: type=4, attr=0xf, range=[0x00000000c5cc9000-0x00000000c5ce7000) (0MB)
[ 0.000000] efi: mem33: type=7, attr=0xf, range=[0x00000000c5ce7000-0x00000000c5ced000) (0MB)
[ 0.000000] efi: mem34: type=4, attr=0xf, range=[0x00000000c5ced000-0x00000000c7c0b000) (31MB)
[ 0.000000] efi: mem35: type=7, attr=0xf, range=[0x00000000c7c0b000-0x00000000c8986000) (13MB)
[ 0.000000] efi: mem36: type=3, attr=0xf, range=[0x00000000c8986000-0x00000000c8c0b000) (2MB)
[ 0.000000] efi: mem37: type=0, attr=0xf, range=[0x00000000c8c0b000-0x00000000c8e5d000) (2MB)
[ 0.000000] efi: mem38: type=0, attr=0xf, range=[0x00000000c8e5d000-0x00000000c910b000) (2MB)
[ 0.000000] efi: mem39: type=7, attr=0xf, range=[0x00000000c910b000-0x00000000c963b000) (5MB)
[ 0.000000] efi: mem40: type=10, attr=0xf, range=[0x00000000c963b000-0x00000000c9779000) (1MB)
[ 0.000000] efi: mem41: type=10, attr=0xf, range=[0x00000000c9779000-0x00000000c9790000) (0MB)
[ 0.000000] efi: mem42: type=10, attr=0xf, range=[0x00000000c9790000-0x00000000c9794000) (0MB)
[ 0.000000] efi: mem43: type=10, attr=0xf, range=[0x00000000c9794000-0x00000000c97a8000) (0MB)
[ 0.000000] efi: mem44: type=10, attr=0xf, range=[0x00000000c97a8000-0x00000000c97ab000) (0MB)
[ 0.000000] efi: mem45: type=6, attr=0x800000000000000f, range=[0x00000000c97ab000-0x00000000c9d4a000) (5MB)
[ 0.000000] efi: mem46: type=6, attr=0x800000000000000f, range=[0x00000000c9d4a000-0x00000000c9eb7000) (1MB)
[ 0.000000] efi: mem47: type=6, attr=0x800000000000000f, range=[0x00000000c9eb7000-0x00000000c9eb9000) (0MB)
[ 0.000000] efi: mem48: type=6, attr=0x800000000000000f, range=[0x00000000c9eb9000-0x00000000c9f58000) (0MB)
[ 0.000000] efi: mem49: type=5, attr=0x800000000000000f, range=[0x00000000c9f58000-0x00000000c9f9a000) (0MB)
[ 0.000000] efi: mem50: type=5, attr=0x800000000000000f, range=[0x00000000c9f9a000-0x00000000c9fff000) (0MB)
[ 0.000000] efi: mem51: type=4, attr=0xf, range=[0x00000000c9fff000-0x00000000ca000000) (0MB)
[ 0.000000] efi: mem52: type=7, attr=0xf, range=[0x0000000100000000-0x000000022fe00000) (4862MB)
[ 0.000000] efi: mem53: type=0, attr=0x0, range=[0x00000000cb000000-0x00000000cf200000) (66MB)
[ 0.000000] efi: mem54: type=11, attr=0x8000000000000001, range=[0x00000000f8000000-0x00000000fc000000) (64MB)
[ 0.000000] efi: mem55: type=11, attr=0x8000000000000001, range=[0x00000000fec00000-0x00000000fec01000) (0MB)
[ 0.000000] efi: mem56: type=11, attr=0x8000000000000001, range=[0x00000000fed00000-0x00000000fed04000) (0MB)
[ 0.000000] efi: mem57: type=11, attr=0x8000000000000001, range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
[ 0.000000] efi: mem58: type=11, attr=0x8000000000000001, range=[0x00000000fee00000-0x00000000fee01000) (0MB)
[ 0.000000] efi: mem59: type=11, attr=0x8000000000000001, range=[0x00000000ff000000-0x0000000100000000) (16MB)
[ 0.000000] SMBIOS 2.8 present.
[ 0.000000] DMI: Notebook W65_67SJ /W65_67SJ , BIOS 1.03.04 03/13/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x22fe00 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7E00000000 write-back
[ 0.000000] 1 base 0200000000 mask 7FE0000000 write-back
[ 0.000000] 2 base 0220000000 mask 7FF0000000 write-back
[ 0.000000] 3 base 00E0000000 mask 7FE0000000 uncachable
[ 0.000000] 4 base 00D0000000 mask 7FF0000000 uncachable
[ 0.000000] 5 base 00CC000000 mask 7FFC000000 uncachable
[ 0.000000] 6 base 00CB000000 mask 7FFF000000 uncachable
[ 0.000000] 7 base 022FE00000 mask 7FFFE00000 uncachable
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xcb000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xca000 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b23000, 0x01b23fff] PGTABLE
[ 0.000000] BRK [0x01b24000, 0x01b24fff] PGTABLE
[ 0.000000] BRK [0x01b25000, 0x01b25fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x22fc00000-0x22fdfffff]
[ 0.000000] [mem 0x22fc00000-0x22fdfffff] page 2M
[ 0.000000] BRK [0x01b26000, 0x01b26fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x22c000000-0x22fbfffff]
[ 0.000000] [mem 0x22c000000-0x22fbfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x200000000-0x22bffffff]
[ 0.000000] [mem 0x200000000-0x22bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xb8115fff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
[ 0.000000] [mem 0x80000000-0xb7ffffff] page 2M
[ 0.000000] [mem 0xb8000000-0xb8115fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xb811d000-0xb894bfff]
[ 0.000000] [mem 0xb811d000-0xb81fffff] page 4k
[ 0.000000] [mem 0xb8200000-0xb87fffff] page 2M
[ 0.000000] [mem 0xb8800000-0xb894bfff] page 4k
[ 0.000000] BRK [0x01b27000, 0x01b27fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0xb8bee000-0xc8c0afff]
[ 0.000000] [mem 0xb8bee000-0xb8bfffff] page 4k
[ 0.000000] [mem 0xb8c00000-0xc8bfffff] page 2M
[ 0.000000] [mem 0xc8c00000-0xc8c0afff] page 4k
[ 0.000000] BRK [0x01b28000, 0x01b28fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0xc910b000-0xc963afff]
[ 0.000000] [mem 0xc910b000-0xc91fffff] page 4k
[ 0.000000] [mem 0xc9200000-0xc95fffff] page 2M
[ 0.000000] [mem 0xc9600000-0xc963afff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xc9fff000-0xc9ffffff]
[ 0.000000] [mem 0xc9fff000-0xc9ffffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff]
[ 0.000000] [mem 0x100000000-0x1ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x7f834000-0x7fffffff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000C973F000 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x00000000C973F090 00009C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x00000000C97503C8 00010C (v05 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000C973F1C0 011202 (v02 ALASKA A M I 00000034 INTL 20120711)
[ 0.000000] ACPI: FACS 0x00000000C97AAF80 000040
[ 0.000000] ACPI: APIC 0x00000000C97504D8 000072 (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x00000000C9750550 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: ASF! 0x00000000C9750598 0000A5 (v32 INTEL HCG 00000001 TFSM 000F4240)
[ 0.000000] ACPI: SSDT 0x00000000C9750640 000F92 (v01 TrmRef PtidDevc 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000C97515D8 000539 (v01 PmRef Cpu0Ist 00003000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000C9751B18 000AD8 (v01 PmRef CpuPm 00003000 INTL 20120711)
[ 0.000000] ACPI: MCFG 0x00000000C97525F0 00003C (v01 ALASKA A M I 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000C9752630 000038 (v01 ALASKA A M I 01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 0x00000000C9752668 000315 (v01 SataRe SataTabl 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000C9752980 001C47 (v01 SaSsdt SaSsdt 00003000 INTL 20091112)
[ 0.000000] ACPI: SSDT 0x00000000C97545C8 000F2E (v01 SgRef SgPeg 00001000 INTL 20120711)
[ 0.000000] ACPI: DMAR 0x00000000C97554F8 0000B8 (v01 INTEL HSW 00000001 INTL 00000001)
[ 0.000000] ACPI: SSDT 0x00000000C97555B0 001C34 (v01 OptRef OptTabl 00001000 INTL 20120711)
[ 0.000000] ACPI: BGRT 0x00000000C97571E8 000038 (v00 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000022fdfffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x22fdfffff]
[ 0.000000] NODE_DATA [mem 0x22fdf4000-0x22fdf8fff]
[ 0.000000] [ffffea0000000000-ffffea0008bfffff] PMD -> [ffff880227400000-ffff88022f3fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x22fdfffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x00057fff]
[ 0.000000] node 0: [mem 0x00059000-0x0009dfff]
[ 0.000000] node 0: [mem 0x00100000-0xb8115fff]
[ 0.000000] node 0: [mem 0xb811d000-0xb894bfff]
[ 0.000000] node 0: [mem 0xb8bee000-0xc8c0afff]
[ 0.000000] node 0: [mem 0xc910b000-0xc963afff]
[ 0.000000] node 0: [mem 0xc9fff000-0xc9ffffff]
[ 0.000000] node 0: [mem 0x100000000-0x22fdfffff]
[ 0.000000] On node 0 totalpages: 2067503
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 12795 pages used for memmap
[ 0.000000] DMA32 zone: 818835 pages, LIFO batch:31
[ 0.000000] Normal zone: 19448 pages used for memmap
[ 0.000000] Normal zone: 1244672 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics stolen memory at 0xcb200000-0xcf1fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x00058000-0x00058fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xb719e000-0xb719efff]
[ 0.000000] PM: Registered nosave memory: [mem 0xb71b7000-0xb71b7fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xb8116000-0xb811cfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xb894c000-0xb8bedfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xc8c0b000-0xc910afff]
[ 0.000000] PM: Registered nosave memory: [mem 0xc963b000-0xc97aafff]
[ 0.000000] PM: Registered nosave memory: [mem 0xc97ab000-0xc9ffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xca000000-0xcaffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcb000000-0xcf1fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcf200000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xcf200000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88022fa00000 s86784 r8192 d23808 u524288
[ 0.000000] pcpu-alloc: s86784 r8192 d23808 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2035175
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: initrd=\initramfs-linux.img root=/dev/sda5 rw quiet ipv6.disable_ipv6=1 rcutree.rcu_idle_gp_delay=1
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 8008164K/8270012K available (5336K kernel code, 887K rwdata, 1688K rodata, 1128K init, 1164K bss, 261848K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS:8448 nr_irqs:712 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 33554432 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] tsc: Detected 2893.349 MHz processor
[ 0.000020] Calibrating delay loop (skipped), value calculated using timer frequency.. 5789.81 BogoMIPS (lpj=9644496)
[ 0.000023] pid_max: default: 32768 minimum: 301
[ 0.000027] ACPI: Core revision 20140424
[ 0.009095] ACPI: All ACPI Tables successfully acquired
[ 0.019679] Security Framework initialized
[ 0.019684] Yama: becoming mindful.
[ 0.020009] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.021690] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.022491] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.022497] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.022684] Initializing cgroup subsys memory
[ 0.022697] Initializing cgroup subsys devices
[ 0.022701] Initializing cgroup subsys freezer
[ 0.022703] Initializing cgroup subsys net_cls
[ 0.022706] Initializing cgroup subsys blkio
[ 0.022723] CPU: Physical Processor ID: 0
[ 0.022724] CPU: Processor Core ID: 0
[ 0.022727] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.023451] mce: CPU supports 7 MCE banks
[ 0.023459] CPU0: Thermal monitoring enabled (TM1)
[ 0.023467] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
tlb_flushall_shift: 6
[ 0.023534] Freeing SMP alternatives memory: 20K (ffffffff819f9000 - ffffffff819fe000)
[ 0.024857] ftrace: allocating 20445 entries in 80 pages
[ 0.030748] dmar: Host address width 39
[ 0.030749] dmar: DRHD base: 0x000000fed90000 flags: 0x0
[ 0.030757] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c0000020660462 ecap f0101a
[ 0.030758] dmar: DRHD base: 0x000000fed91000 flags: 0x1
[ 0.030762] dmar: IOMMU 1: reg_base_addr fed91000 ver 1:0 cap d2008020660462 ecap f010da
[ 0.030762] dmar: RMRR base: 0x000000c9e7a000 end: 0x000000c9e88fff
[ 0.030763] dmar: RMRR base: 0x000000cb000000 end: 0x000000cf1fffff
[ 0.030828] IOAPIC id 8 under DRHD base 0xfed91000 IOMMU 1
[ 0.030828] HPET id 0 under DRHD base 0xfed91000
[ 0.030829] Queued invalidation will be enabled to support x2apic and Intr-remapping.
[ 0.031028] Enabled IRQ remapping in x2apic mode
[ 0.031029] Enabling x2apic
[ 0.031030] Enabled x2apic
[ 0.031035] Switched APIC routing to cluster x2apic.
[ 0.031449] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.064460] smpboot: CPU0: Intel(R) Core(TM) i5-4340M CPU @ 2.90GHz (fam: 06, model: 3c, stepping: 03)
[ 0.064466] TSC deadline timer enabled
[ 0.064483] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.064496] ... version: 3
[ 0.064497] ... bit width: 48
[ 0.064498] ... generic registers: 4
[ 0.064498] ... value mask: 0000ffffffffffff
[ 0.064499] ... max period: 0000ffffffffffff
[ 0.064500] ... fixed-purpose events: 3
[ 0.064500] ... event mask: 000000070000000f
[ 0.087944] x86: Booting SMP configuration:
[ 0.087945] .... node #0, CPUs: #1
[ 0.101808] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.108499] #2 #3
[ 0.142890] x86: Booted up 1 node, 4 CPUs
[ 0.142893] smpboot: Total of 4 processors activated (23156.24 BogoMIPS)
[ 0.145458] devtmpfs: initialized
[ 0.146940] PM: Registering ACPI NVS region [mem 0xb8116000-0xb811cfff] (28672 bytes)
[ 0.146941] PM: Registering ACPI NVS region [mem 0xc963b000-0xc97aafff] (1507328 bytes)
[ 0.147466] pinctrl core: initialized pinctrl subsystem
[ 0.147497] RTC time: 15:10:36, date: 10/09/14
[ 0.147530] NET: Registered protocol family 16
[ 0.147599] cpuidle: using governor ladder
[ 0.147601] cpuidle: using governor menu
[ 0.147626] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.147627] ACPI: bus type PCI registered
[ 0.147628] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.147675] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.147676] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.147728] PCI: Using configuration type 1 for base access
[ 0.159864] ACPI: Added _OSI(Module Device)
[ 0.159866] ACPI: Added _OSI(Processor Device)
[ 0.159867] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.159868] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.162812] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.185983] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.196372] ACPI: Dynamic OEM Table Load:
[ 0.196377] ACPI: SSDT 0xFFFF880223C6C800 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120711)
[ 0.208943] ACPI: Dynamic OEM Table Load:
[ 0.208948] ACPI: SSDT 0xFFFF880223EB1000 0005AA (v01 PmRef ApIst 00003000 INTL 20120711)
[ 0.223042] ACPI: Dynamic OEM Table Load:
[ 0.223045] ACPI: SSDT 0xFFFF880223EDA400 000119 (v01 PmRef ApCst 00003000 INTL 20120711)
[ 0.249835] ACPI: Interpreter enabled
[ 0.249842] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140424/hwxface-580)
[ 0.249846] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[ 0.249859] ACPI: (supports S0 S3 S4 S5)
[ 0.249860] ACPI: Using IOAPIC for interrupt routing
[ 0.249879] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.254504] ACPI: Power Resource [NVP3] (on)
[ 0.254519] ACPI: Power Resource [NVP2] (on)
[ 0.267026] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.267031] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.267141] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug PME]
[ 0.267228] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
[ 0.267555] PCI host bridge to bus 0000:00
[ 0.267557] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.267558] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.267560] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.267561] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.267562] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
[ 0.267563] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
[ 0.267564] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
[ 0.267565] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff]
[ 0.267566] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 0.267567] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 0.267568] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 0.267569] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 0.267570] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 0.267571] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 0.267571] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff]
[ 0.267572] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff]
[ 0.267574] pci_bus 0000:00: root bus resource [mem 0xcf200000-0xfeafffff]
[ 0.267579] pci 0000:00:00.0: [8086:0c04] type 00 class 0x060000
[ 0.267650] pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
[ 0.267677] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.267714] pci 0000:00:01.0: System wakeup disabled by ACPI
[ 0.267744] pci 0000:00:02.0: [8086:0416] type 00 class 0x030000
[ 0.267753] pci 0000:00:02.0: reg 0x10: [mem 0xf7400000-0xf77fffff 64bit]
[ 0.267757] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.267761] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.267822] pci 0000:00:03.0: [8086:0c0c] type 00 class 0x040300
[ 0.267827] pci 0000:00:03.0: reg 0x10: [mem 0xf7a14000-0xf7a17fff 64bit]
[ 0.267909] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
[ 0.267925] pci 0000:00:14.0: reg 0x10: [mem 0xf7a00000-0xf7a0ffff 64bit]
[ 0.267978] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.268009] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.268038] pci 0000:00:16.0: [8086:8c3a] type 00 class 0x078000
[ 0.268055] pci 0000:00:16.0: reg 0x10: [mem 0xf7a1e000-0xf7a1e00f 64bit]
[ 0.268111] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.268178] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
[ 0.268197] pci 0000:00:1a.0: reg 0x10: [mem 0xf7a1c000-0xf7a1c3ff]
[ 0.268285] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.268323] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 0.268351] pci 0000:00:1b.0: [8086:8c20] type 00 class 0x040300
[ 0.268363] pci 0000:00:1b.0: reg 0x10: [mem 0xf7a10000-0xf7a13fff 64bit]
[ 0.268413] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.268445] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.268469] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
[ 0.268526] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.268557] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.268582] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400
[ 0.268639] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.268671] pci 0000:00:1c.2: System wakeup disabled by ACPI
[ 0.268696] pci 0000:00:1c.3: [8086:8c16] type 01 class 0x060400
[ 0.268753] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.268784] pci 0000:00:1c.3: System wakeup disabled by ACPI
[ 0.268815] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
[ 0.268832] pci 0000:00:1d.0: reg 0x10: [mem 0xf7a1b000-0xf7a1b3ff]
[ 0.268910] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.268948] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.268975] pci 0000:00:1f.0: [8086:8c49] type 00 class 0x060100
[ 0.269111] pci 0000:00:1f.2: [8086:8c03] type 00 class 0x010601
[ 0.269124] pci 0000:00:1f.2: reg 0x10: [io 0xf0b0-0xf0b7]
[ 0.269131] pci 0000:00:1f.2: reg 0x14: [io 0xf0a0-0xf0a3]
[ 0.269137] pci 0000:00:1f.2: reg 0x18: [io 0xf090-0xf097]
[ 0.269143] pci 0000:00:1f.2: reg 0x1c: [io 0xf080-0xf083]
[ 0.269149] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
[ 0.269155] pci 0000:00:1f.2: reg 0x24: [mem 0xf7a1a000-0xf7a1a7ff]
[ 0.269186] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.269235] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
[ 0.269247] pci 0000:00:1f.3: reg 0x10: [mem 0xf7a19000-0xf7a190ff 64bit]
[ 0.269264] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.269352] pci 0000:01:00.0: [10de:1391] type 00 class 0x030200
[ 0.269359] pci 0000:01:00.0: reg 0x10: [mem 0xf6000000-0xf6ffffff]
[ 0.269365] pci 0000:01:00.0: reg 0x14: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.269372] pci 0000:01:00.0: reg 0x1c: [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 0.269376] pci 0000:01:00.0: reg 0x24: [io 0xe000-0xe07f]
[ 0.269380] pci 0000:01:00.0: reg 0x30: [mem 0xf7000000-0xf707ffff pref]
[ 0.269417] pci 0000:01:00.0: System wakeup disabled by ACPI
[ 0.273042] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.273044] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.273046] pci 0000:00:01.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 0.273049] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[ 0.273108] acpiphp: Slot [1] registered
[ 0.273113] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.273227] pci 0000:03:00.0: [8086:08b1] type 00 class 0x028000
[ 0.273275] pci 0000:03:00.0: reg 0x10: [mem 0xf7900000-0xf7901fff 64bit]
[ 0.273485] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.273538] pci 0000:03:00.0: System wakeup disabled by ACPI
[ 0.279737] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.279742] pci 0000:00:1c.2: bridge window [mem 0xf7900000-0xf79fffff]
[ 0.279821] pci 0000:04:00.0: [10ec:5289] type 00 class 0xff0000
[ 0.279836] pci 0000:04:00.0: reg 0x10: [mem 0xf7800000-0xf780ffff]
[ 0.279954] pci 0000:04:00.0: supports D1 D2
[ 0.279956] pci 0000:04:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.279988] pci 0000:04:00.0: System wakeup disabled by ACPI
[ 0.280028] pci 0000:04:00.2: [10ec:8168] type 00 class 0x020000
[ 0.280046] pci 0000:04:00.2: reg 0x10: [io 0xd000-0xd0ff]
[ 0.280073] pci 0000:04:00.2: reg 0x18: [mem 0xf2104000-0xf2104fff 64bit pref]
[ 0.280091] pci 0000:04:00.2: reg 0x20: [mem 0xf2100000-0xf2103fff 64bit pref]
[ 0.280169] pci 0000:04:00.2: supports D1 D2
[ 0.280171] pci 0000:04:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.280200] pci 0000:04:00.2: System wakeup disabled by ACPI
[ 0.286399] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 0.286403] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
[ 0.286406] pci 0000:00:1c.3: bridge window [mem 0xf7800000-0xf78fffff]
[ 0.286411] pci 0000:00:1c.3: bridge window [mem 0xf2100000-0xf21fffff 64bit pref]
[ 0.286443] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
[ 0.287065] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287099] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287133] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287166] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287199] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287231] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287264] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287298] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287496] ACPI: Enabled 4 GPEs in block 00 to 3F
[ 0.287524] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.287603] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.287606] vgaarb: loaded
[ 0.287606] vgaarb: bridge control possible 0000:00:02.0
[ 0.287660] PCI: Using ACPI for IRQ routing
[ 0.288826] PCI: pci_cache_line_size set to 64 bytes
[ 0.288879] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
[ 0.288880] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[ 0.288881] e820: reserve RAM buffer [mem 0xb719e018-0xb7ffffff]
[ 0.288882] e820: reserve RAM buffer [mem 0xb8116000-0xbbffffff]
[ 0.288883] e820: reserve RAM buffer [mem 0xb894c000-0xbbffffff]
[ 0.288883] e820: reserve RAM buffer [mem 0xc8c0b000-0xcbffffff]
[ 0.288884] e820: reserve RAM buffer [mem 0xc963b000-0xcbffffff]
[ 0.288885] e820: reserve RAM buffer [mem 0xca000000-0xcbffffff]
[ 0.288886] e820: reserve RAM buffer [mem 0x22fe00000-0x22fffffff]
[ 0.288958] NetLabel: Initializing
[ 0.288959] NetLabel: domain hash size = 128
[ 0.288959] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.288967] NetLabel: unlabeled traffic allowed by default
[ 0.288985] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.288988] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.291011] Switched to clocksource hpet
[ 0.294250] pnp: PnP ACPI init
[ 0.294261] ACPI: bus type PNP registered
[ 0.294319] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.294321] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.294511] system 00:01: [io 0x0680-0x069f] has been reserved
[ 0.294513] system 00:01: [io 0xffff] has been reserved
[ 0.294514] system 00:01: [io 0xffff] has been reserved
[ 0.294515] system 00:01: [io 0xffff] has been reserved
[ 0.294516] system 00:01: [io 0x1c00-0x1cfe] has been reserved
[ 0.294517] system 00:01: [io 0x1d00-0x1dfe] has been reserved
[ 0.294518] system 00:01: [io 0x1e00-0x1efe] has been reserved
[ 0.294519] system 00:01: [io 0x1f00-0x1ffe] has been reserved
[ 0.294520] system 00:01: [io 0x1800-0x18fe] could not be reserved
[ 0.294521] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.294522] system 00:01: [io 0x3322-0x3323] has been reserved
[ 0.294523] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.294546] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.294576] system 00:03: [io 0x1854-0x1857] has been reserved
[ 0.294577] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.294599] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.294641] pnp 00:05: Plug and Play ACPI device, IDs ETD0403 PNP0f13 (active)
[ 0.294678] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.294680] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.294932] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.294933] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.294934] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.294936] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.294937] system 00:07: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.294939] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.294940] system 00:07: [mem 0xfed90000-0xfed93fff] could not be reserved
[ 0.294941] system 00:07: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.294943] system 00:07: [mem 0xff000000-0xffffffff] has been reserved
[ 0.294944] system 00:07: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.294945] system 00:07: [mem 0xf7fee000-0xf7feefff] has been reserved
[ 0.294947] system 00:07: [mem 0xf7fd0000-0xf7fdffff] has been reserved
[ 0.294948] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.295088] pnp: PnP ACPI: found 8 devices
[ 0.295089] ACPI: bus type PNP unregistered
[ 0.300962] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.300964] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.300966] pci 0000:00:01.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 0.300968] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[ 0.300970] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.300979] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.300983] pci 0000:00:1c.2: bridge window [mem 0xf7900000-0xf79fffff]
[ 0.300989] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 0.300992] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
[ 0.300995] pci 0000:00:1c.3: bridge window [mem 0xf7800000-0xf78fffff]
[ 0.300998] pci 0000:00:1c.3: bridge window [mem 0xf2100000-0xf21fffff 64bit pref]
[ 0.301004] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.301005] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.301006] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.301007] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.301007] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.301008] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.301009] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.301015] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.301016] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.301017] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.301018] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.301019] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.301020] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.301020] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.301021] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff]
[ 0.301022] pci_bus 0000:00: resource 19 [mem 0xcf200000-0xfeafffff]
[ 0.301023] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 0.301024] pci_bus 0000:01: resource 1 [mem 0xf6000000-0xf70fffff]
[ 0.301025] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xf1ffffff 64bit pref]
[ 0.301026] pci_bus 0000:03: resource 1 [mem 0xf7900000-0xf79fffff]
[ 0.301027] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
[ 0.301028] pci_bus 0000:04: resource 1 [mem 0xf7800000-0xf78fffff]
[ 0.301029] pci_bus 0000:04: resource 2 [mem 0xf2100000-0xf21fffff 64bit pref]
[ 0.301046] NET: Registered protocol family 2
[ 0.301179] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.301304] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.301489] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.301506] TCP: reno registered
[ 0.301513] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.301544] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.301593] NET: Registered protocol family 1
[ 0.301603] pci 0000:00:02.0: Boot video device
[ 0.301931] PCI: CLS 64 bytes, default 64
[ 0.301958] Unpacking initramfs...
[ 0.386167] Freeing initrd memory: 7984K (ffff88007f834000 - ffff880080000000)
[ 0.386188] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.386190] software IO TLB [mem 0xc1b1f000-0xc5b1f000] (64MB) mapped at [ffff8800c1b1f000-ffff8800c5b1efff]
[ 0.386318] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[ 0.386350] Scanning for low memory corruption every 60 seconds
[ 0.386511] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.386731] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.387500] zbud: loaded
[ 0.387608] VFS: Disk quotas dquot_6.5.2
[ 0.387628] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.387708] msgmni has been set to 15743
[ 0.387742] Key type big_key registered
[ 0.387839] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.387873] io scheduler noop registered
[ 0.387875] io scheduler deadline registered
[ 0.387904] io scheduler cfq registered (default)
[ 0.388020] pcieport 0000:00:01.0: irq 42 for MSI/MSI-X
[ 0.388274] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.388283] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.388307] efifb: probing for efifb
[ 0.388322] efifb: framebuffer at 0xd0000000, mapped to 0xffffc90004f00000, using 8100k, total 8100k
[ 0.388323] efifb: mode is 1920x1080x32, linelength=7680, pages=1
[ 0.388323] efifb: scrolling: redraw
[ 0.388325] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.391551] Console: switching to colour frame buffer device 240x67
[ 0.394714] fb0: EFI VGA frame buffer device
[ 0.394720] intel_idle: MWAIT substates: 0x42120
[ 0.394721] intel_idle: v0.4 model 0x3C
[ 0.394722] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.394847] GHES: HEST is not enabled!
[ 0.394901] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.395174] Linux agpgart interface v0.103
[ 0.395207] rtc_cmos 00:02: RTC can wake from S4
[ 0.395303] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.395327] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.395336] Intel P-state driver initializing.
[ 0.395347] Intel pstate controlling: cpu 0
[ 0.395362] Intel pstate controlling: cpu 1
[ 0.395371] Intel pstate controlling: cpu 2
[ 0.395382] Intel pstate controlling: cpu 3
[ 0.395464] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.395725] TCP: cubic registered
[ 0.395956] NET: Registered protocol family 10
[ 0.396437] NET: Registered protocol family 17
[ 0.397160] registered taskstats version 1
[ 0.398429] Magic number: 2:906:183
[ 0.398473] acpi device:42: hash matches
[ 0.398596] rtc_cmos 00:02: setting system clock to 2014-10-09 15:10:36 UTC (1412867436)
[ 0.398804] PM: Hibernation image not present or could not be loaded.
[ 0.400643] Freeing unused kernel memory: 1128K (ffffffff818df000 - ffffffff819f9000)
[ 0.400647] Write protecting the kernel read-only data: 8192k
[ 0.404839] Freeing unused kernel memory: 796K (ffff880001539000 - ffff880001600000)
[ 0.405463] Freeing unused kernel memory: 360K (ffff8800017a6000 - ffff880001800000)
[ 0.409793] random: systemd-tmpfile urandom read with 1 bits of entropy available
[ 0.410535] systemd-udevd[58]: starting version 216
[ 0.415323] nvidia: module license 'NVIDIA' taints kernel.
[ 0.415327] Disabling lock debugging due to kernel taint
[ 0.422425] nvidia 0000:01:00.0: enabling device (0006 -> 0007)
[ 0.422497] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 0.422519] nvidia: probe of 0000:01:00.0 failed with error -1
[ 0.422530] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 0.422530] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 0.439552] sdhci: Secure Digital Host Controller Interface driver
[ 0.439555] sdhci: Copyright(c) Pierre Ossman
[ 0.440845] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:ELNM] at 0x60,0x64 irq 1,12
[ 0.444930] i8042: Detected active multiplexing controller, rev 1.1
[ 0.446883] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.446964] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.446980] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.446995] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.447010] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.449893] rtsx_pci 0000:04:00.0: enabling device (0000 -> 0002)
[ 0.449895] ACPI: bus type USB registered
[ 0.449923] usbcore: registered new interface driver usbfs
[ 0.449932] usbcore: registered new interface driver hub
[ 0.450037] usbcore: registered new device driver usb
[ 0.450180] rtsx_pci 0000:04:00.0: irq 43 for MSI/MSI-X
[ 0.450194] rtsx_pci 0000:04:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 43
[ 0.451289] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.451629] ehci-pci: EHCI PCI platform driver
[ 0.451707] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.451719] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 0.451840] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 0.451885] xhci_hcd 0000:00:14.0: irq 44 for MSI/MSI-X
[ 0.452315] hub 1-0:1.0: USB hub found
[ 0.452419] hub 1-0:1.0: 14 ports detected
[ 0.453990] SCSI subsystem initialized
[ 0.455355] libata version 3.00 loaded.
[ 0.457428] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 0.457521] nvidia: probe of 0000:01:00.0 failed with error -1
[ 0.457532] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 0.457533] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 0.458920] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.458924] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 0.459079] hub 2-0:1.0: USB hub found
[ 0.459092] hub 2-0:1.0: 4 ports detected
[ 0.459940] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 0.459945] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 0.459957] ehci-pci 0000:00:1a.0: debug port 2
[ 0.463868] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 0.463885] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7a1c000
[ 0.466653] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.471099] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.471222] hub 3-0:1.0: USB hub found
[ 0.471226] hub 3-0:1.0: 2 ports detected
[ 0.471429] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.471433] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 0.471444] ehci-pci 0000:00:1d.0: debug port 2
[ 0.475342] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 0.475363] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7a1b000
[ 0.484460] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.484616] hub 4-0:1.0: USB hub found
[ 0.484620] hub 4-0:1.0: 2 ports detected
[ 0.484757] ahci 0000:00:1f.2: version 3.0
[ 0.484899] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[ 0.484921] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 0.484948] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x35 impl SATA mode
[ 0.484952] ahci 0000:00:1f.2: flags: 64bit ncq stag led clo pio slum part ems sxs apst
[ 0.504953] scsi0 : ahci
[ 0.505056] scsi1 : ahci
[ 0.505142] scsi2 : ahci
[ 0.505215] scsi3 : ahci
[ 0.505290] scsi4 : ahci
[ 0.505363] scsi5 : ahci
[ 0.505395] ata1: SATA max UDMA/133 abar m2048@0xf7a1a000 port 0xf7a1a100 irq 45
[ 0.505396] ata2: DUMMY
[ 0.505398] ata3: SATA max UDMA/133 abar m2048@0xf7a1a000 port 0xf7a1a200 irq 45
[ 0.505399] ata4: DUMMY
[ 0.505401] ata5: SATA max UDMA/133 abar m2048@0xf7a1a000 port 0xf7a1a300 irq 45
[ 0.505403] ata6: SATA max UDMA/133 abar m2048@0xf7a1a000 port 0xf7a1a380 irq 45
[ 0.817900] usb 1-7: new full-speed USB device number 2 using xhci_hcd
[ 0.824536] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.828238] ata1.00: ATAPI: TSSTcorp CDDVDW SN-208FB, SB00, max UDMA/100
[ 0.830890] ata1.00: configured for UDMA/100
[ 0.836443] scsi 0:0:0:0: CD-ROM TSSTcorp CDDVDW SN-208FB SB00 PQ: 0 ANSI: 5
[ 1.151305] usb 1-8: new high-speed USB device number 3 using xhci_hcd
[ 1.164609] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.387979] tsc: Refined TSC clocksource calibration: 2893.300 MHz
[ 1.484683] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.486801] ata5.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.486804] ata5.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 1.486806] ata5.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.486982] ata5.00: supports DRM functions and may not be fully accessible
[ 1.487059] ata5.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 1.487061] ata5.00: ATA-9: Samsung SSD 840 EVO 250GB mSATA, EXT41B6Q, max UDMA/133
[ 1.487062] ata5.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 1.487488] ata5.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.487491] ata5.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 1.487493] ata5.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.487669] ata5.00: supports DRM functions and may not be fully accessible
[ 1.487745] ata5.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 1.487809] ata5.00: configured for UDMA/133
[ 1.487882] scsi 4:0:0:0: Direct-Access ATA Samsung SSD 840 1B6Q PQ: 0 ANSI: 5
[ 1.504700] usb 3-1: new high-speed USB device number 2 using ehci-pci
[ 1.628611] hub 3-1:1.0: USB hub found
[ 1.628715] hub 3-1:1.0: 6 ports detected
[ 1.734739] usb 4-1: new high-speed USB device number 2 using ehci-pci
[ 1.808089] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.808826] ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.808829] ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 1.808831] ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.809472] ata6.00: ATA-9: WDC WD10JPVX-00JC3T0, 01.01A01, max UDMA/133
[ 1.809475] ata6.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.810294] ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.810297] ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 1.810299] ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.810940] ata6.00: configured for UDMA/133
[ 1.811024] scsi 5:0:0:0: Direct-Access ATA WDC WD10JPVX-00J 1A01 PQ: 0 ANSI: 5
[ 1.828896] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.828899] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.829047] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.829174] sd 4:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.829250] sd 4:0:0:0: [sda] Write Protect is off
[ 1.829253] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.829273] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.829307] sd 5:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 1.829309] sd 5:0:0:0: [sdb] 4096-byte physical blocks
[ 1.829324] sd 5:0:0:0: [sdb] Write Protect is off
[ 1.829325] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.829332] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.833215] sda: sda1 sda2 sda3 sda4 sda5
[ 1.833616] sd 4:0:0:0: [sda] Attached SCSI disk
[ 1.858666] hub 4-1:1.0: USB hub found
[ 1.858764] hub 4-1:1.0: 8 ports detected
[ 1.931835] sdb: sdb1 sdb2 sdb3 sdb4
[ 1.932379] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 2.388247] Switched to clocksource tsc
[ 2.419201] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[ 2.567012] EXT4-fs (sda5): re-mounted. Opts: data=ordered,discard
[ 2.586418] systemd-udevd[162]: starting version 216
[ 2.592445] random: nonblocking pool is initialized
[ 2.659141] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 2.662736] mei_me 0000:00:16.0: irq 46 for MSI/MSI-X
[ 2.664631] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
[ 2.664635] ACPI: Power Button [PWRB]
[ 2.664679] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input6
[ 2.664682] ACPI: Sleep Button [SLPB]
[ 2.664733] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input7
[ 2.664773] ACPI: Lid Switch [LID0]
[ 2.665022] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input8
[ 2.665025] ACPI: Power Button [PWRF]
[ 2.665141] ACPI: AC Adapter [AC] (on-line)
[ 2.667736] ACPI Warning: SystemIO range 0x000000000000f040-0x000000000000f05f conflicts with OpRegion 0x000000000000f040-0x000000000000f04f (\_SB_.PCI0.SBUS.SMBI) (20140424/utaddress-258)
[ 2.667742] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.669446] wmi: Mapper loaded
[ 2.671588] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.692393] [drm] Initialized drm 1.1.0 20060810
[ 2.696742] snd_hda_intel 0000:00:03.0: enabling device (0000 -> 0002)
[ 2.696877] snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)
[ 2.696971] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[ 2.707358] [drm] Memory usable by graphics device = 2048M
[ 2.707363] [drm] Replacing VGA console driver
[ 2.707366] checking generic (d0000000 7e9000) vs hw (d0000000 10000000)
[ 2.707367] fb: switching to inteldrmfb from EFI VGA
[ 2.707385] Console: switching to colour dummy device 80x25
[ 2.710351] sound hdaudioC1D0: autoconfig: line_outs=1 (0x24/0x0/0x0/0x0/0x0) type:speaker
[ 2.710356] sound hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 2.710358] sound hdaudioC1D0: hp_outs=1 (0x25/0x0/0x0/0x0/0x0)
[ 2.710359] sound hdaudioC1D0: mono: mono_out=0x0
[ 2.710360] sound hdaudioC1D0: inputs:
[ 2.710362] sound hdaudioC1D0: Internal Mic=0x30
[ 2.710364] sound hdaudioC1D0: Mic=0x2b
[ 2.710804] ACPI: Battery Slot [BAT0] (battery present)
[ 2.714192] thermal LNXTHERM:00: registered as thermal_zone0
[ 2.714195] ACPI: Thermal Zone [TZ0] (14 C)
[ 2.715795] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input9
[ 2.715826] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
[ 2.724955] i915 0000:00:02.0: irq 48 for MSI/MSI-X
[ 2.724965] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.724967] [drm] Driver supports precise vblank timestamp query.
[ 2.737377] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.737384] r8169 0000:04:00.2: can't disable ASPM; OS doesn't have ASPM control
[ 2.742415] microcode: CPU0 sig=0x306c3, pf=0x10, revision=0x17
[ 2.742489] cfg80211: Calling CRDA to update world regulatory domain
[ 2.745089] r8169 0000:04:00.2: irq 49 for MSI/MSI-X
[ 2.745270] r8169 0000:04:00.2 eth0: RTL8411 at 0xffffc90004c84000, 80:fa:5b:02:45:07, XID 08800800 IRQ 49
[ 2.745272] r8169 0000:04:00.2 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 2.745315] microcode: CPU1 sig=0x306c3, pf=0x10, revision=0x17
[ 2.745328] microcode: CPU2 sig=0x306c3, pf=0x10, revision=0x17
[ 2.745339] microcode: CPU3 sig=0x306c3, pf=0x10, revision=0x17
[ 2.745388] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 2.745604] Bluetooth: Core ver 2.19
[ 2.745614] NET: Registered protocol family 31
[ 2.745615] Bluetooth: HCI device and connection manager initialized
[ 2.745620] Bluetooth: HCI socket layer initialized
[ 2.745622] Bluetooth: L2CAP socket layer initialized
[ 2.745627] Bluetooth: SCO socket layer initialized
[ 2.748195] media: Linux media interface: v0.10
[ 2.753454] Linux video capture interface: v2.00
[ 2.754656] AVX2 version of gcm_enc/dec engaged.
[ 2.756983] usbcore: registered new interface driver btusb
[ 2.760011] Intel(R) Wireless WiFi driver for Linux, in-tree:
[ 2.760014] Copyright(c) 2003- 2014 Intel Corporation
[ 2.760055] iwlwifi 0000:03:00.0: enabling device (0000 -> 0002)
[ 2.760187] iwlwifi 0000:03:00.0: irq 50 for MSI/MSI-X
[ 2.760307] uvcvideo: Found UVC 1.00 device Chicony USB 2.0 Camera (04f2:b43b)
[ 2.764039] iwlwifi 0000:03:00.0: loaded firmware version 23.214.9.0 op_mode iwlmvm
[ 2.765870] input: Chicony USB 2.0 Camera as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0/input/input13
[ 2.765960] usbcore: registered new interface driver uvcvideo
[ 2.765969] USB Video Class driver (1.1.1)
[ 2.768578] [drm] VBT doesn't support DRRS
[ 2.772344] Bluetooth: hci0: read Intel version: 370710018002030d41
[ 2.772347] Bluetooth: hci0: Intel device is already patched. patch num: 41
[ 2.786141] iTCO_vendor_support: vendor-support=0
[ 2.796870] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 2.796909] iTCO_wdt: Found a Lynx Point TCO device (Version=2, TCOBASE=0x1860)
[ 2.796998] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 2.810892] iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144
[ 2.811059] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
[ 2.811293] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
[ 2.958002] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 2.958033] nvidia: probe of 0000:01:00.0 failed with error -1
[ 2.958044] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 2.958045] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 2.960203] fbcon: inteldrmfb (fb0) is primary device
[ 3.019635] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[ 3.561746] psmouse serio2: elantech: assuming hardware version 3 (with firmware version 0x450f02)
[ 3.660974] psmouse serio2: elantech: Synaptics capabilities query result 0x79, 0x17, 0x0c.
[ 3.988549] EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: data=ordered
[ 3.988697] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio2/input/input12
[ 3.991679] mousedev: PS/2 mouse device common for all mice
[ 4.101934] Console: switching to colour frame buffer device 240x67
[ 4.105588] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 4.105588] i915 0000:00:02.0: registered panic notifier
[ 4.118668] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[ 4.118700] ACPI: Video Device [PEGP] (multi-head: yes rom: yes post: no)
[ 4.118754] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:50/LNXVIDEO:00/input/input16
[ 4.118867] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.118954] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input17
[ 4.119017] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.125265] snd_hda_intel 0000:00:03.0: irq 51 for MSI/MSI-X
[ 4.136612] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input18
[ 4.136672] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input19
[ 4.136724] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input20
[ 4.179405] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: data=ordered
[ 4.219066] systemd-journald[146]: Received request to flush runtime journal from PID 1
[ 4.348712] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 4.727547] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 4.727571] nvidia: probe of 0000:01:00.0 failed with error -1
[ 4.727582] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 4.727582] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 4.832411] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 4.832435] nvidia: probe of 0000:01:00.0 failed with error -1
[ 4.832447] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 4.832447] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 4.932489] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 4.932512] nvidia: probe of 0000:01:00.0 failed with error -1
[ 4.932523] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 4.932524] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 5.034916] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 5.034939] nvidia: probe of 0000:01:00.0 failed with error -1
[ 5.034950] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 5.034950] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 5.132660] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 5.132684] nvidia: probe of 0000:01:00.0 failed with error -1
[ 5.132694] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 5.132695] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 5.242426] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 5.242450] nvidia: probe of 0000:01:00.0 failed with error -1
[ 5.242462] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 5.242462] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 9.749419] r8169 0000:04:00.2 eth0: link down
[ 9.749453] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.750962] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
[ 9.751189] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
[ 9.762802] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 10.545589] cfg80211: Calling CRDA to update world regulatory domain
[ 13.577678] wlan0: authenticate with 00:25:53:07:7c:e0
[ 13.580685] wlan0: send auth to 00:25:53:07:7c:e0 (try 1/3)
[ 13.582500] wlan0: authenticated
[ 13.584009] wlan0: associate with 00:25:53:07:7c:e0 (try 1/3)
[ 13.586776] wlan0: RX AssocResp from 00:25:53:07:7c:e0 (capab=0x411 status=0 aid=2)
[ 13.592537] wlan0: associated
[ 13.592558] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1011.531361] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:1391)
NVRM: installed in this system is not supported by the 304.123
NVRM: NVIDIA Linux driver release. Please see 'Appendix
NVRM: A - Supported NVIDIA GPU Products' in this release's
NVRM: README, available on the Linux driver download page
NVRM: at www.nvidia.com.
[ 1011.531395] nvidia: probe of 0000:01:00.0 failed with error -1
[ 1011.531411] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 1011.531412] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 1393.740889] usb 1-6: new high-speed USB device number 4 using xhci_hcd
[ 1393.933036] usb-storage 1-6:1.0: USB Mass Storage device detected
[ 1393.933230] scsi6 : usb-storage 1-6:1.0
[ 1393.933428] usbcore: registered new interface driver usb-storage
[ 1393.935440] usbcore: registered new interface driver uas
[ 1394.971011] scsi 6:0:0:0: Direct-Access Verbatim STORE N GO 5.00 PQ: 0 ANSI: 0 CCS
[ 1395.351383] sd 6:0:0:0: [sdc] 15646720 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 1395.351612] sd 6:0:0:0: [sdc] Write Protect is off
[ 1395.351625] sd 6:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 1395.351861] sd 6:0:0:0: [sdc] No Caching mode page found
[ 1395.351908] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 1395.384088] sdc:
[ 1395.384881] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 1436.372212] usb 1-6: USB disconnect, device number 4Thank You in advance for helping!
Last edited by GiBg1aN (2014-10-09 15:42:16)
Offline
#2 2014-10-09 16:17:14
- exadrid
- Member
- From: Ottawa, Ontario, Canada
- Registered: 2010-01-27
- Posts: 29
Re: X Doesn't start(NVIDIA drivers)
I had lots of problems with 2 graphic cards also. Did you properly install Bumblebee (https://wiki.archlinux.org/index.php/bumblebee)?
Offline
#3 2014-10-09 16:27:05
- GiBg1aN
- Member
- Registered: 2014-10-08
- Posts: 8
Re: X Doesn't start(NVIDIA drivers)
exadrid wrote:
I had lots of problems with 2 graphic cards also. Did you properly install Bumblebee (https://wiki.archlinux.org/index.php/bumblebee)?
I wanted to, but it isn't compatible with nvidia-304xx... so i thought that i installed the wrong driver, but i checked to nvidia website and for my gpu(gtx 850m) the last version is 340.46, according with repository version, nvidia-304xx should be right(nvidia package is 3.43), but I don't really know what to do, thus i answered here. Thank for helping anyway 
.
Last edited by GiBg1aN (2014-10-09 16:33:13)
Offline
#4 2014-10-09 23:33:58
- mrunion
- Member
- From: Jonesborough, TN
- Registered: 2007-01-26
- Posts: 1,938
- Website
Re: X Doesn't start(NVIDIA drivers)
Unless I'm mistaken, won't the GTX850 use the latest nvidia 343 drivers? The nVidia website shows both 340 AND the 343 BETA for that card. I only have a GT 730M on this laptop and am running the nvidia 343 drivers.
Matt
"It is very difficult to educate the educated."
Offline
#5 2014-10-10 06:56:04
- GiBg1aN
- Member
- Registered: 2014-10-08
- Posts: 8
Re: X Doesn't start(NVIDIA drivers)
You are right,
I installed 340xx driver, now the module is loaded, but now i have a black screen, i added rcutree... kernel parameter and nvidia module to mkinitcpio.conf, but I X doesn't start. Moreover I can't install bumblebee because it is not compatibile with those drivers. I installed xf86-video-modesetting and xorg-xrandr but nothing. Maybe adding xrandr commands to .xinirc... But i use gdm so i don't know where to put it... Any Ideas? Should I try nvidia or nvidia-beta package? Wiki is not much clear...
Thanks for helping.
EDIT:
I unistalled all drivers and restarted with nvidia package and followed wiki's instructions, now all seem working! But.... If I don't use gdm, i can't lock the screen and I have to do startx every time. How to add the following commands to gdm service? Thanks for helping.
.xinitrc
xrandr --setprovideroutputsource modesetting NVIDIA-0
xrandr --auto
exec gnome-session # I know that I don't need this if I use gdm.Last edited by GiBg1aN (2014-10-11 13:35:43)
Offline
Pages: 1