You are not logged in.
Pages: 1
Hi. I install arch and xfce desktop.
But my partitions not shown in thunar file manager.
In windows all of my partition is works fine.
And here is the fdisk -l output command:
[root@archlinux hossein]# fdisk -l
Disk /dev/sda: 465.8 GiB, 500107862016 bytes, 976773168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x0c4f0c4e
Device Boot Start End Sectors Size Id Type
/dev/sda1 2048 126160895 126158848 60.2G 7 HPFS/NTFS/exFAT
/dev/sda2 126164990 976768064 850603075 405.6G 5 Extended
/dev/sda5 163846998 377657343 213810346 102G 7 HPFS/NTFS/exFAT
/dev/sda6 459685297 471041864 11356568 5.4G 83 Linux
/dev/sda7 471041928 675838484 204796557 97.7G 7 HPFS/NTFS/exFAT
/dev/sda8 675838548 880635104 204796557 97.7G 7 HPFS/NTFS/exFAT
/dev/sda9 880635168 976768064 96132897 45.9G 7 HPFS/NTFS/exFAT
/dev/sda10 * 126164992 163846632 37681641 18G 83 Linux
/dev/sda11 377659392 459683839 82024448 39.1G 83 Linux
Partition table entries are not in disk order.
Disk /dev/sdb: 14.5 GiB, 15504900096 bytes, 30283008 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x769fce30
Device Boot Start End Sectors Size Id Type
/dev/sdb1 * 0 1282047 1282048 626M 0 Empty
/dev/sdb2 172 63659 63488 31M ef EFI (FAT-12/16/32)
And here is my fstab file:
[root@archlinux hossein]# cat /etc/fstab
#
# /etc/fstab: static file system information
#
# <file system> <dir> <type> <options> <dump> <pass>
# /dev/sda10
UUID=15cf7f12-cc4f-42d8-bd40-270eaf98a822 / ext4 rw,relatime,data=ordered 0 1
# /dev/sda11
UUID=6c43c5d4-33e8-43d7-8786-7887808cf596 /home ext4 rw,relatime,data=ordered 0 2
# /dev/sda6
UUID=eeabe591-7cf1-41c0-8f9a-9bed6c6fbb67 none swap defaults 0 0
I add UUIDs of my ntfs partitions to the fstab file but no luck.
Aslo i install ntfs-3d. But i don't know hot mount my partitions.
Thanks for helps.
Sorry for my bad english!
Last edited by HDArtworks (2015-05-20 13:21:04)
Offline
It has been ages since I used thunar myself, but do you have gvfs and thunar-volman installed?
https://wiki.archlinux.org/index.php/Thunar
Offline
I don't understand. Where's you ntfs partition in the fstab?
Aslo i install ntfs-3d. But i don't know hot mount my partitions.
It's ntfs-3g. Read the wiki on how to mount the partitions.
Offline
Pages: 1