You are not logged in.
I have an issue with the automout in Gnome3.16 under archlinux when I try to connect a WD My Passport Ultra HDD to my Acer Notebook.
This are my specs:
System: Host: archlinux Kernel: 4.1.5-1-ARCH x86_64 (64 bit gcc: 5.2.0)
Desktop: Gnome 3.16.3 (Gtk 3.16.6) info: gnome-shell dm: gdm Distro: Arch Linux
Machine: Mobo: Acer model: Aspire V5-531 v: V2.15 Bios: Phoenix v: V2.15 date: 12/21/2012
CPU: Dual core Intel Celeron 1007U (-MCP-) cache: 2048 KB
flags: (lm nx sse sse2 sse3 sse4_1 sse4_2 ssse3 vmx) bmips: 5989
clock speeds: min/max: 800/1500 MHz 1: 800 MHz 2: 884 MHz
Graphics: Card: Intel 3rd Gen Core processor Graphics Controller bus-ID: 00:02.0 chip-ID: 8086:0156
Display Server: X.Org 1.17.2 driver: N/A Resolution: 1366x768@60.05hz
GLX Renderer: Mesa DRI Intel Ivybridge Mobile GLX Version: 3.0 Mesa 10.6.5 Direct Rendering: Yes
Audio: Card Intel 7 Series/C210 Series Family High Definition Audio Controller
driver: snd_hda_intel bus-ID: 00:1b.0 chip-ID: 8086:1e20
Sound: Advanced Linux Sound Architecture v: k4.1.5-1-ARCH
Network: Card-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
driver: r8169 port: 2000 bus-ID: 02:00.2 chip-ID: 10ec:8168
IF: enp2s0f2 state: down mac: 20:6a:8a:b0:82:18
Card-2: Qualcomm Atheros AR9462 Wireless Network Adapter
driver: ath9k bus-ID: 03:00.0 chip-ID: 168c:0034
IF: wlp3s0 state: up mac: b8:76:3f:9b:3c:c3
Drives: HDD Total Size: 500.1GB (93.3% used)
ID-1: /dev/sda model: Hitachi_HTS54505 size: 500.1GB serial: TEA55AL507S44K
Partition: ID-1: / size: 453G used: 430G (100%) fs: ext4 dev: /dev/sda3
label: N/A uuid: c0f363be-1714-49eb-999d-12c75223cce8
ID-2: /boot size: 494M used: 37M (8%) fs: vfat dev: /dev/sda1 label: N/A uuid: C5D8-C1B3
ID-3: swap-1 size: 5.81GB used: 0.07GB (1%) fs: swap dev: /dev/sda2
label: N/A uuid: db09b6ea-3be6-4cb8-906d-08500d3932c3
Sensors: System Temperatures: cpu: 57.0C mobo: 49.0C
Fan Speeds (in rpm): cpu: N/A
Info: Processes: 193 Uptime: 4 days Memory: 2211.6/5770.4MB Init: systemd v: 224 Gcc sys: 5.2.0
Client: Shell (bash 4.3.391 running in python2) inxi: 2.2.28 and this is the error message I get with dmesg:
[179640.405309] usb 3-1.4: new full-speed USB device number 47 using ehci-pci
[179640.490584] usb 3-1.4: string descriptor 0 read error: -22
[179640.681526] usb 3-1.4: USB disconnect, device number 47
[179640.868520] usb 3-1.4: new full-speed USB device number 48 using ehci-pci
[179640.953807] usb 3-1.4: string descriptor 0 read error: -22
[179641.011800] systemd[1]: cups.socket: Cannot add dependency job, ignoring: Input/output error
[179641.961476] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[179641.963445] ata1.00: configured for UDMA/133
[179642.031942] IPv6: ADDRCONF(NETDEV_UP): enp2s0f2: link is not ready
[179642.141083] r8169 0000:02:00.2 enp2s0f2: link down
[179645.827345] wlp3s0: authenticate with 88:f7:c7:9d:29:e9
[179645.842319] wlp3s0: send auth to 88:f7:c7:9d:29:e9 (try 1/3)
[179645.844320] wlp3s0: authenticated
[179645.844574] ath9k 0000:03:00.0 wlp3s0: disabling HT/VHT due to WEP/TKIP use
[179645.846844] wlp3s0: associate with 88:f7:c7:9d:29:e9 (try 1/3)
[179645.849796] wlp3s0: RX AssocResp from 88:f7:c7:9d:29:e9 (capab=0x411 status=0 aid=6)
[179645.849923] wlp3s0: associated
[179649.312460] usb 3-1.2: new high-speed USB device number 49 using ehci-pci
[180008.358948] usb 3-1.2: reset high-speed USB device number 49 using ehci-pci
[180013.296487] usb 3-1.2: USB disconnect, device number 49Automount is TRUE in
gsettings org.gnome.desktop.media-handlingAutomount was never deactivated (as far as I can tell) and is functional only after a fresh boot. I think that automount does not function any longer after I put my notebook to sleep and wake it up again. Quite some time ago, it was functioning just fine. It is only now that I start to take care of the issue.
Does somebody has an idea?
Last edited by Eugenespeirs (2015-08-25 20:14:28)
Offline