You are not logged in.

#1 2006-04-07 19:24:03

o2bfishn
Member
Registered: 2005-12-22
Posts: 53

cd-rom burner not working after update

did a -Syu and installed the most current kernel 2.6.16.1-8, rebooted and now my cd burner isnt recognized. the window that opens when you put a cd in that asks what you want to do doesnt open and k3b no longer sees the drive. did i miss something on the update for the kernel? i did notice a new fstab.pacnew, but there is nothing different in it that fstab did not already have

Offline

#2 2006-04-09 00:00:35

o2bfishn
Member
Registered: 2005-12-22
Posts: 53

Re: cd-rom burner not working after update

anyone?

Offline

#3 2006-04-09 00:37:25

McQueen
Member
From: Arizona
Registered: 2006-03-20
Posts: 387

Re: cd-rom burner not working after update

I can't do anything other than confirm the problem.
My system is experiencing the same symptoms.

EDIT: Perhaps just a little flaky...it all works again on 2nd reboot.


/path/to/Truth

Offline

#4 2006-04-09 21:01:15

RobK
Member
Registered: 2005-12-07
Posts: 121

Re: cd-rom burner not working after update

I am having similar problems.  I filed a bug report.  See http://bugs.archlinux.org/task/4419

Please feel free to add anything to the bug report that might help solve the problem.

Rob

Offline

#5 2006-04-12 22:37:57

TomE
Member
Registered: 2005-08-06
Posts: 164

Re: cd-rom burner not working after update

do you have the ide_cd module loaded?

Offline

#6 2006-04-13 00:32:00

poetofnumbers
Member
From: Kansas, United States
Registered: 2004-10-30
Posts: 106
Website

Re: cd-rom burner not working after update

I'm running into the same problem.  Here is some (edited) output from cdrdao:

# sudo cdrdao copy --source-device ATA:1,0,0 --device ATA:0,0,0

...
Turning BURN-Proof on
Enabling JustSpeed.
Executing power calibration...
Power calibration successful.
--device: Success.  : scsi sendcmd: no error
CDB:  2A 00 FF FF FF 6A 00 00 1A 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0
Sense flags: Blk 0 (not valid) 
resid: 61152
cmd finished after 0.003s timeout 180s
ERROR: Write data failed.
ERROR: Writing failed.
ERROR: CD copying failed.

The output before this is normal.  The errors at the bottom are the only anamoly.  Modules are autoloaded on my computer and ide_cd is loaded.
Unlike those above me, my optical drives are present in /dev.


Sweet, now I can play with myself.

Offline

#7 2006-04-13 03:23:51

Snowman
Developer/Forum Fellow
From: Montreal, Canada
Registered: 2004-08-20
Posts: 5,212

Re: cd-rom burner not working after update

try:
modprobe capability

Offline

#8 2006-04-13 17:43:00

poetofnumbers
Member
From: Kansas, United States
Registered: 2004-10-30
Posts: 106
Website

Re: cd-rom burner not working after update

adding capability worked for me.  Why did this work?  Why do I need to add it now but didn't need to earlier?


Sweet, now I can play with myself.

Offline

#9 2006-04-24 13:15:09

Michel
Member
From: Belgium
Registered: 2004-07-31
Posts: 286

Re: cd-rom burner not working after update

Heya,

are you sure that you have permissions to read and write to the device? I noticed that the group of the cdrom and dvdrom that I checked was set to disk and not optical.

greetings,

Michel

Offline

Board footer

Powered by FluxBB