External Monitor not detected (Intel Graphics Card)

dkl · 2015-11-20 19:02:33

Hi everyone,

I am having issues getting my external monitor working (HDMI connection). I checked some other threads about this issue, but it usually comes down to proprietary drivers not working properly. I just have an Intel Graphics card for which open source support should be fine. The output of

 lspci -v

is:

00:02.0 VGA compatible controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Graphics & Display (rev 0e) (prog-if 00 [VGA controller])
        Subsystem: Acer Incorporated [ALI] Device 0933
        Flags: bus master, fast devsel, latency 0, IRQ 265
        Memory at 90000000 (32-bit, non-prefetchable) [size=4M]
        Memory at 80000000 (32-bit, prefetchable) [size=256M]
        I/O ports at 2050 [size=8]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: <access denied>
        Kernel driver in use: i915
        Kernel modules: i915

The output of

 xrandr

is (even if I have the monitor connected)

Screen 0: minimum 8 x 8, current 1366 x 768, maximum 32767 x 32767
eDP1 connected primary 1366x768+0+0 (normal left inverted right x axis y axis) 256mm x 144mm
   1366x768      60.11*+
   1280x720      60.00  
   1024x768      60.00  
   1024x576      60.00  
   960x540       60.00  
   800x600       60.32    56.25  
   864x486       60.00  
   640x480       59.94  
   720x405       60.00  
   680x384       60.00  
   640x360       60.00  
VIRTUAL1 disconnected (normal left inverted right x axis y axis)

I should point out that have had the same problem under kubuntu and linux mint since about two month ago.
Even after many hours of googling, I still don't even understand what causes the problem, let alone how to fix it. Any help would be highly appreciated.

Regards and thanks in advance

Xabre · 2015-11-20 19:04:31

Does that laptop have two GPUs and you disabled non-Intel one?

dkl · 2015-11-20 19:13:59

hi, thanks for the fast reply. No I don't have a hybrid graphics system.

Lone_Wolf · 2015-11-21 13:56:31

dkl, please post Xorg.0.log and dmesg or journalctrl -b .

dkl · 2015-11-21 16:40:21

Xorg.0.log:

[   310.753] _XSERVTransSocketUNIXCreateListener: ...SocketCreateListener() failed
[   310.753] _XSERVTransMakeAllCOTSServerListeners: server already running
[   310.753] (EE)
Fatal server error:
[   310.753] (EE) Cannot establish any listening sockets - Make sure an X server isn't already running(EE)
[   310.754] (EE)
Please consult the The X.Org Foundation support
         at http://wiki.x.org
 for help.
[   310.754] (EE) Please also check the log file at "~/.local/share/xorg/Xorg.0.log" for additional information.
[   310.754] (EE)
[   310.754] (EE) Server terminated with error (1). Closing log file.

dmesg:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.2.5-1-ARCH (builduser@tobias) (gcc version 5.2.0 (GCC) ) #1 SMP PREEMPT Tue Oct 27 08:13:28 CET 2015
[    0.000000] Command line: BOOT_IMAGE=../vmlinuz-linux root=/dev/sda1 rw initrd=../initramfs-linux.img
[    0.000000] x86/fpu: Legacy x87 FPU detected.
[    0.000000] x86/fpu: Using 'lazy' FPU context switches.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001effffff] usable
[    0.000000] BIOS-e820: [mem 0x000000001f000000-0x000000001f0fffff] reserved
[    0.000000] BIOS-e820: [mem 0x000000001f100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000200fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020100000-0x00000000781aefff] usable
[    0.000000] BIOS-e820: [mem 0x00000000781af000-0x00000000787aefff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000787af000-0x00000000788aefff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000788af000-0x00000000788eefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000788ef000-0x00000000794c5fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000794c6000-0x0000000079dc5fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000079dc6000-0x0000000079ffffff] usable
[    0.000000] BIOS-e820: [mem 0x000000007a000000-0x000000007a7fffff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007ae00000-0x000000007fffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed03000-0x00000000fed03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed0c000-0x00000000fed0ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1cfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fef00000-0x00000000feffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: Acer Aspire E3-112/R2, BIOS V1.03 07/22/2014                             
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved                  
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable                               
[    0.000000] e820: last_pfn = 0x180000 max_arch_pfn = 0x400000000                          
[    0.000000] MTRR default type: uncachable                                                 
[    0.000000] MTRR fixed ranges enabled:                                                    
[    0.000000]   00000-9FFFF write-back                                                      
[    0.000000]   A0000-BFFFF uncachable                                                      
[    0.000000]   C0000-FFFFF write-protect                                                   
[    0.000000] MTRR variable ranges enabled:                                                 
[    0.000000]   0 base 0FFC00000 mask FFFC00000 write-protect                               
[    0.000000]   1 base 000000000 mask F80000000 write-back                                  
[    0.000000]   2 base 07C000000 mask FFC000000 uncachable                                  
[    0.000000]   3 base 07B000000 mask FFF000000 uncachable                                  
[    0.000000]   4 base 07AE00000 mask FFFE00000 uncachable
[    0.000000]   5 base 100000000 mask F80000000 write-back
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- WT  
[    0.000000] e820: last_pfn = 0x7a000 max_arch_pfn = 0x400000000
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01b36000, 0x01b36fff] PGTABLE
[    0.000000] BRK [0x01b37000, 0x01b37fff] PGTABLE
[    0.000000] BRK [0x01b38000, 0x01b38fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x17fe00000-0x17fffffff]
[    0.000000]  [mem 0x17fe00000-0x17fffffff] page 2M
[    0.000000] BRK [0x01b39000, 0x01b39fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x160000000-0x17fdfffff]
[    0.000000]  [mem 0x160000000-0x17fdfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x1effffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x1effffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x1f100000-0x1fffffff]
[    0.000000]  [mem 0x1f100000-0x1f1fffff] page 4k
[    0.000000]  [mem 0x1f200000-0x1fffffff] page 2M
[    0.000000] BRK [0x01b3a000, 0x01b3afff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x20100000-0x781aefff]
[    0.000000]  [mem 0x20100000-0x201fffff] page 4k
[    0.000000]  [mem 0x20200000-0x77ffffff] page 2M
[    0.000000]  [mem 0x78000000-0x781aefff] page 4k
[    0.000000] BRK [0x01b3b000, 0x01b3bfff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x788ef000-0x794c5fff]
[    0.000000]  [mem 0x788ef000-0x789fffff] page 4k
[    0.000000]  [mem 0x78a00000-0x793fffff] page 2M
[    0.000000]  [mem 0x79400000-0x794c5fff] page 4k
[    0.000000] init_memory_mapping: [mem 0x79dc6000-0x79ffffff]
[    0.000000]  [mem 0x79dc6000-0x79dfffff] page 4k
[    0.000000]  [mem 0x79e00000-0x79ffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x100000000-0x15fffffff]
[    0.000000]  [mem 0x100000000-0x15fffffff] page 2M
[    0.000000] RAMDISK: [mem 0x79151000-0x794c5fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000FE020 000024 (v02 ACRSYS)
[    0.000000] ACPI: XSDT 0x00000000788EE120 0000A4 (v01 ACRSYS ACRPRDCT 00000003      01000013)
[    0.000000] ACPI: FACP 0x00000000788EB000 00010C (v05 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.000000] ACPI: DSDT 0x00000000788DD000 008EEF (v02 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.000000] ACPI: FACS 0x0000000078868000 000040
[    0.000000] ACPI: UEFI 0x00000000788ED000 000236 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.000000] ACPI: HPET 0x00000000788EA000 000038 (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.000000] ACPI: LPIT 0x00000000788E9000 000104 (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.000000] ACPI: APIC 0x00000000788E8000 000084 (v03 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.000000] ACPI: MCFG 0x00000000788E7000 00003C (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000788E6000 000581 (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000788DB000 00138A (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000788DA000 000763 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000788D9000 000290 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000788D8000 00017A (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.000000] ACPI: UEFI 0x00000000788D7000 000042 (v01 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000788D3000 00305B (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.000000] ACPI: CSRT 0x00000000788D2000 00014C (v00 ACRSYS ACRPRDCT 00000005 1025 00040000)
[    0.000000] ACPI: SSDT 0x00000000788D1000 0003E6 (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.000000] ACPI: FPDT 0x00000000788D0000 000044 (v01 ACRSYS ACRPRDCT 00000002 1025 00040000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000017fffffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x17fff6000-0x17fff9fff]
[    0.000000]  [ffffea0000000000-ffffea0005ffffff] PMD -> [ffff88017b600000-ffff88017f5fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000017fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009dfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x000000001effffff]
[    0.000000]   node   0: [mem 0x000000001f100000-0x000000001fffffff]
[    0.000000]   node   0: [mem 0x0000000020100000-0x00000000781aefff]
[    0.000000]   node   0: [mem 0x00000000788ef000-0x00000000794c5fff]
[    0.000000]   node   0: [mem 0x0000000079dc6000-0x0000000079ffffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x000000017fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000017fffffff]
[    0.000000] On node 0 totalpages: 1019229
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3997 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 7671 pages used for memmap
[    0.000000]   DMA32 zone: 490944 pages, LIFO batch:31
[    0.000000]   Normal zone: 8192 pages used for memmap
[    0.000000]   Normal zone: 524288 pages, LIFO batch:31
[    0.000000] x86/hpet: Will disable the HPET for this platform because it's not reliable
[    0.000000] Reserving Intel graphics stolen memory at 0x7b000000-0x7effffff
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-86
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x1f000000-0x1f0fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x20000000-0x200fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x781af000-0x787aefff]
[    0.000000] PM: Registered nosave memory: [mem 0x787af000-0x788aefff]
[    0.000000] PM: Registered nosave memory: [mem 0x788af000-0x788eefff]
[    0.000000] PM: Registered nosave memory: [mem 0x794c6000-0x79dc5fff]
[    0.000000] PM: Registered nosave memory: [mem 0x7a000000-0x7a7fffff]
[    0.000000] PM: Registered nosave memory: [mem 0x7a800000-0x7adfffff]
[    0.000000] PM: Registered nosave memory: [mem 0x7ae00000-0x7fffffff]
[    0.000000] PM: Registered nosave memory: [mem 0x80000000-0xdfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xe3ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe4000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed01fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed02000-0xfed02fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed03000-0xfed03fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed07fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed08000-0xfed08fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed09000-0xfed0bfff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed0c000-0xfed0ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed1bfff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1cfff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1d000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeefffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfef00000-0xfeffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffbfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xffc00000-0xffffffff]
[    0.000000] e820: [mem 0x80000000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[    0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 32 pages/cpu @ffff88017fc00000 s91480 r8192 d31400 u524288
[    0.000000] pcpu-alloc: s91480 r8192 d31400 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1003281
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=../vmlinuz-linux root=/dev/sda1 rw initrd=../initramfs-linux.img
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3929396K/4076916K available (5611K kernel code, 922K rwdata, 1768K rodata, 1180K init, 1152K bss, 147520K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:8448 nr_irqs:1024 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Maximum core-clock to bus-clock ratio: 0x16
[    0.000000] Resolved frequency ID: 0, frequency: 83200 KHz
[    0.000000] TSC runs at 1830400 KHz
[    0.000000] lapic_timer_frequency = 277333
[    0.000000] tsc: Detected 1830.400 MHz processor
[    0.000043] Calibrating delay loop (skipped), value calculated using timer frequency.. 3662.33 BogoMIPS (lpj=6101333)
[    0.000049] pid_max: default: 32768 minimum: 301
[    0.000062] ACPI: Core revision 20150619
[    0.024351] ACPI: All ACPI Tables successfully acquired
[    0.024398] Security Framework initialized
[    0.024403] Yama: becoming mindful.
[    0.024922] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.026983] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.028317] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.028333] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.028723] Initializing cgroup subsys blkio
[    0.028733] Initializing cgroup subsys memory
[    0.028751] Initializing cgroup subsys devices
[    0.028758] Initializing cgroup subsys freezer
[    0.028764] Initializing cgroup subsys net_cls
[    0.028791] CPU: Physical Processor ID: 0
[    0.028794] CPU: Processor Core ID: 0
[    0.028801] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.028803] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.033615] mce: CPU supports 6 MCE banks
[    0.033625] CPU0: Thermal monitoring handled by SMI
[    0.033631] process: using mwait in idle threads
[    0.033637] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[    0.033641] Last level dTLB entries: 4KB 128, 2MB 16, 4MB 16, 1GB 0
[    0.033992] Freeing SMP alternatives memory: 20K (ffffffff81a0f000 - ffffffff81a14000)
[    0.051720] ftrace: allocating 22161 entries in 87 pages
[    0.066370] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.099375] TSC deadline timer enabled
[    0.099382] smpboot: CPU0: Intel(R) Celeron(R) CPU  N2940  @ 1.83GHz (fam: 06, model: 37, stepping: 08)
[    0.099424] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, full-width counters, Intel PMU driver.
[    0.099441] ... version:                3
[    0.099443] ... bit width:              40
[    0.099446] ... generic registers:      2
[    0.099448] ... value mask:             000000ffffffffff
[    0.099451] ... max period:             000000ffffffffff
[    0.099453] ... fixed-purpose events:   3
[    0.099456] ... event mask:             0000000700000003
[    0.112865] x86: Booting SMP configuration:
[    0.112870] .... node  #0, CPUs:      #1
[    0.118686] CPU1: Thermal monitoring handled by SMI
[    0.120888] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.124187]  #2
[    0.130001] CPU2: Thermal monitoring handled by SMI
[    0.135577]  #3
[    0.141392] CPU3: Thermal monitoring handled by SMI
[    0.143533] x86: Booted up 1 node, 4 CPUs
[    0.143540] smpboot: Total of 4 processors activated (14649.33 BogoMIPS)
[    0.144538] devtmpfs: initialized
[    0.152552] PM: Registering ACPI NVS region [mem 0x787af000-0x788aefff] (1048576 bytes)
[    0.152586] PM: Registering ACPI NVS region [mem 0x794c6000-0x79dc5fff] (9437184 bytes)
[    0.153006] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.153182] pinctrl core: initialized pinctrl subsystem
[    0.153250] RTC time: 16:35:49, date: 11/21/15
[    0.153567] NET: Registered protocol family 16
[    0.170206] cpuidle: using governor ladder
[    0.186883] cpuidle: using governor menu
[    0.186963] ACPI: bus type PCI registered
[    0.186968] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.187118] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[    0.187124] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820
[    0.187137] PCI: Using configuration type 1 for base access
[    0.204310] ACPI: Added _OSI(Module Device)
[    0.204315] ACPI: Added _OSI(Processor Device)
[    0.204318] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.204321] ACPI: Added _OSI(Processor Aggregator Device)
[    0.219961] ACPI: Dynamic OEM Table Load:
[    0.219979] ACPI: SSDT 0xFFFF88017A6C4800 0003BC (v01 PmRef  Cpu0Ist  00003000 INTL 20130117)
[    0.221162] ACPI: Dynamic OEM Table Load:
[    0.221176] ACPI: SSDT 0xFFFF88017A631800 000433 (v01 PmRef  Cpu0Cst  00003001 INTL 20130117)
[    0.222817] ACPI: Dynamic OEM Table Load:
[    0.222831] ACPI: SSDT 0xFFFF88017A6A0200 00015F (v01 PmRef  ApIst    00003000 INTL 20130117)
[    0.223975] ACPI: Dynamic OEM Table Load:
[    0.223989] ACPI: SSDT 0xFFFF88017A655780 00008D (v01 PmRef  ApCst    00003000 INTL 20130117)
[    0.226383] ACPI : EC: EC started
[    0.226763] ACPI: Interpreter enabled
[    0.226777] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150619/hwxface-580)
[    0.226787] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150619/hwxface-580)
[    0.226819] ACPI: (supports S0 S3 S4 S5)
[    0.226823] ACPI: Using IOAPIC for interrupt routing
[    0.226888] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.231501] ACPI: Power Resource [USBC] (on)
[    0.245728] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.245742] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.245974] \_SB_.PCI0:_OSC invalid UUID
[    0.245978] _OSC request data:1 1f 0 
[    0.245987] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.246268] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.246626] PCI host bridge to bus 0000:00
[    0.246634] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.246639] pci_bus 0000:00: root bus resource [io  0x0070-0x0077]
[    0.246644] pci_bus 0000:00: root bus resource [io  0x0000-0x006f window]
[    0.246649] pci_bus 0000:00: root bus resource [io  0x0078-0x0cf7 window]
[    0.246653] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.246658] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.246662] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[    0.246667] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff window]
[    0.246671] pci_bus 0000:00: root bus resource [mem 0x80000000-0x909ffffe window]
[    0.246685] pci 0000:00:00.0: [8086:0f00] type 00 class 0x060000
[    0.246885] pci 0000:00:02.0: [8086:0f31] type 00 class 0x030000
[    0.246908] pci 0000:00:02.0: reg 0x10: [mem 0x90000000-0x903fffff]
[    0.246923] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff pref]
[    0.246949] pci 0000:00:02.0: reg 0x20: [io  0x2050-0x2057]
[    0.247137] pci 0000:00:12.0: [8086:0f16] type 00 class 0x080501
[    0.247165] pci 0000:00:12.0: reg 0x10: [mem 0x90920000-0x90920fff]
[    0.247178] pci 0000:00:12.0: reg 0x14: [mem 0x9091f000-0x9091ffff]
[    0.247244] pci 0000:00:12.0: PME# supported from D0 D3hot
[    0.247408] pci 0000:00:13.0: [8086:0f23] type 00 class 0x010601
[    0.247440] pci 0000:00:13.0: reg 0x10: [io  0x2048-0x204f]
[    0.247452] pci 0000:00:13.0: reg 0x14: [io  0x205c-0x205f]
[    0.247464] pci 0000:00:13.0: reg 0x18: [io  0x2040-0x2047]
[    0.247475] pci 0000:00:13.0: reg 0x1c: [io  0x2058-0x205b]
[    0.247487] pci 0000:00:13.0: reg 0x20: [io  0x2020-0x203f]
[    0.247499] pci 0000:00:13.0: reg 0x24: [mem 0x9091e000-0x9091e7ff]
[    0.247537] pci 0000:00:13.0: PME# supported from D3hot
[    0.247697] pci 0000:00:14.0: [8086:0f35] type 00 class 0x0c0330
[    0.247729] pci 0000:00:14.0: reg 0x10: [mem 0x90900000-0x9090ffff 64bit]
[    0.247785] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.247896] pci 0000:00:14.0: System wakeup disabled by ACPI
[    0.247986] pci 0000:00:17.0: [8086:0f50] type 00 class 0x080501
[    0.248014] pci 0000:00:17.0: reg 0x10: [mem 0x9091d000-0x9091dfff]
[    0.248027] pci 0000:00:17.0: reg 0x14: [mem 0x9091c000-0x9091cfff]
[    0.248094] pci 0000:00:17.0: PME# supported from D0 D3hot
[    0.248258] pci 0000:00:1a.0: [8086:0f18] type 00 class 0x108000
[    0.248302] pci 0000:00:1a.0: reg 0x10: [mem 0x90800000-0x908fffff]
[    0.248318] pci 0000:00:1a.0: reg 0x14: [mem 0x90700000-0x907fffff]
[    0.248407] pci 0000:00:1a.0: PME# supported from D0 D3hot
[    0.248569] pci 0000:00:1b.0: [8086:0f04] type 00 class 0x040300
[    0.248606] pci 0000:00:1b.0: reg 0x10: [mem 0x90910000-0x90913fff 64bit]
[    0.248672] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.248828] pci 0000:00:1c.0: [8086:0f48] type 01 class 0x060400
[    0.248894] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.248981] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.249066] pci 0000:00:1c.1: [8086:0f4a] type 01 class 0x060400
[    0.249132] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.249215] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.249300] pci 0000:00:1c.2: [8086:0f4c] type 01 class 0x060400
[    0.249366] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.249448] pci 0000:00:1c.2: System wakeup disabled by ACPI
[    0.249540] pci 0000:00:1f.0: [8086:0f1c] type 00 class 0x060100
[    0.249767] pci 0000:00:1f.3: [8086:0f12] type 00 class 0x0c0500
[    0.249818] pci 0000:00:1f.3: reg 0x10: [mem 0x90918000-0x9091801f]
[    0.249893] pci 0000:00:1f.3: reg 0x20: [io  0x2000-0x201f]
[    0.250186] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.250310] pci 0000:02:00.0: [168c:0036] type 00 class 0x028000
[    0.250357] pci 0000:02:00.0: reg 0x10: [mem 0x90600000-0x9067ffff 64bit]
[    0.250412] pci 0000:02:00.0: reg 0x30: [mem 0xffff0000-0xffffffff pref]
[    0.250465] pci 0000:02:00.0: supports D1 D2
[    0.250470] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.250517] pci 0000:02:00.0: System wakeup disabled by ACPI
[    0.256973] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.256982] pci 0000:00:1c.1:   bridge window [mem 0x90600000-0x906fffff]
[    0.257093] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000
[    0.257138] pci 0000:03:00.0: reg 0x10: [io  0x1000-0x10ff]
[    0.257169] pci 0000:03:00.0: reg 0x18: [mem 0x90500000-0x90500fff 64bit]
[    0.257190] pci 0000:03:00.0: reg 0x20: [mem 0x90400000-0x90403fff 64bit pref]
[    0.257258] pci 0000:03:00.0: supports D1 D2
[    0.257263] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.257314] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.263642] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.263650] pci 0000:00:1c.2:   bridge window [io  0x1000-0x1fff]
[    0.263656] pci 0000:00:1c.2:   bridge window [mem 0x90500000-0x905fffff]
[    0.263664] pci 0000:00:1c.2:   bridge window [mem 0x90400000-0x904fffff 64bit pref]
[    0.264654] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *7
[    0.264796] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[    0.264935] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.265073] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[    0.265211] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.265349] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *10 11 12 14 15)
[    0.265486] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.265624] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *7
[    0.269967] ACPI: Enabled 4 GPEs in block 00 to 3F
[    0.270239] ACPI : EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
[    0.270478] vgaarb: setting as boot device: PCI:0000:00:02.0
[    0.270483] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.270491] vgaarb: loaded
[    0.270494] vgaarb: bridge control possible 0000:00:02.0
[    0.270715] PCI: Using ACPI for IRQ routing
[    0.272191] PCI: pci_cache_line_size set to 64 bytes
[    0.272252] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[    0.272257] e820: reserve RAM buffer [mem 0x1f000000-0x1fffffff]
[    0.272260] e820: reserve RAM buffer [mem 0x781af000-0x7bffffff]
[    0.272264] e820: reserve RAM buffer [mem 0x794c6000-0x7bffffff]
[    0.272267] e820: reserve RAM buffer [mem 0x7a000000-0x7bffffff]
[    0.272491] NetLabel: Initializing
[    0.272495] NetLabel:  domain hash size = 128
[    0.272497] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.272519] NetLabel:  unlabeled traffic allowed by default
[    0.272604] clocksource: Switched to clocksource refined-jiffies
[    0.283928] pnp: PnP ACPI init
[    0.284046] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.284204] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.284210] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.284216] system 00:01: [io  0x0500-0x05fe] has been reserved
[    0.284220] system 00:01: [io  0x0600-0x061f] has been reserved
[    0.284226] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.284234] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.284380] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.284984] system 00:03: [mem 0xe0000000-0xefffffff] could not be reserved
[    0.284991] system 00:03: [mem 0xfed01000-0xfed01fff] has been reserved
[    0.284996] system 00:03: [mem 0xfed03000-0xfed03fff] has been reserved
[    0.285001] system 00:03: [mem 0xfed04000-0xfed04fff] has been reserved
[    0.285006] system 00:03: [mem 0xfed0c000-0xfed0ffff] could not be reserved
[    0.285011] system 00:03: [mem 0xfed08000-0xfed08fff] has been reserved
[    0.285016] system 00:03: [mem 0xfed1c000-0xfed1cfff] has been reserved
[    0.285021] system 00:03: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.285026] system 00:03: [mem 0xfef00000-0xfeffffff] has been reserved
[    0.285033] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.286722] pnp: PnP ACPI: found 4 devices
[    0.295828] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.295860] clocksource: Switched to clocksource acpi_pm
[    0.295877] pci 0000:02:00.0: can't claim BAR 6 [mem 0xffff0000-0xffffffff pref]: no compatible bridge window
[    0.295897] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 01] add_size 1000
[    0.295904] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[    0.295910] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000 add_align 100000
[    0.295921] pci 0000:00:1c.1: bridge window [io  0x1000-0x0fff] to [bus 02] add_size 1000
[    0.295927] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[    0.295944] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] res_to_dev_res add_size 200000 min_align 100000
[    0.295950] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x002fffff] res_to_dev_res add_size 200000 min_align 100000
[    0.295955] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.295960] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.295966] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.295971] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.295976] pci 0000:00:1c.0: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[    0.295981] pci 0000:00:1c.0: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[    0.295985] pci 0000:00:1c.1: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[    0.295990] pci 0000:00:1c.1: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[    0.296002] pci 0000:00:1c.0: BAR 14: no space for [mem size 0x00200000]
[    0.296008] pci 0000:00:1c.0: BAR 14: failed to assign [mem size 0x00200000]
[    0.296020] pci 0000:00:1c.0: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.296025] pci 0000:00:1c.0: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.296037] pci 0000:00:1c.1: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.296042] pci 0000:00:1c.1: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.296050] pci 0000:00:1c.0: BAR 13: assigned [io  0x3000-0x3fff]
[    0.296057] pci 0000:00:1c.1: BAR 13: assigned [io  0x4000-0x4fff]
[    0.296070] pci 0000:00:1c.1: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.296075] pci 0000:00:1c.1: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.296083] pci 0000:00:1c.0: BAR 14: no space for [mem size 0x00200000]
[    0.296087] pci 0000:00:1c.0: BAR 14: failed to assign [mem size 0x00200000]
[    0.296099] pci 0000:00:1c.0: BAR 15: no space for [mem size 0x00200000 64bit pref]
[    0.296103] pci 0000:00:1c.0: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[    0.296108] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.296114] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.296128] pci 0000:02:00.0: BAR 6: assigned [mem 0x90680000-0x9068ffff pref]
[    0.296133] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.296138] pci 0000:00:1c.1:   bridge window [io  0x4000-0x4fff]
[    0.296145] pci 0000:00:1c.1:   bridge window [mem 0x90600000-0x906fffff]
[    0.296155] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.296160] pci 0000:00:1c.2:   bridge window [io  0x1000-0x1fff]
[    0.296167] pci 0000:00:1c.2:   bridge window [mem 0x90500000-0x905fffff]
[    0.296173] pci 0000:00:1c.2:   bridge window [mem 0x90400000-0x904fffff 64bit pref]
[    0.296181] pci_bus 0000:00: resource 4 [io  0x0070-0x0077]
[    0.296186] pci_bus 0000:00: resource 5 [io  0x0000-0x006f window]
[    0.296191] pci_bus 0000:00: resource 6 [io  0x0078-0x0cf7 window]
[    0.296195] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff window]
[    0.296200] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[    0.296204] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[    0.296209] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000fffff window]
[    0.296213] pci_bus 0000:00: resource 11 [mem 0x80000000-0x909ffffe window]
[    0.296218] pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
[    0.296223] pci_bus 0000:02: resource 0 [io  0x4000-0x4fff]
[    0.296227] pci_bus 0000:02: resource 1 [mem 0x90600000-0x906fffff]
[    0.296232] pci_bus 0000:03: resource 0 [io  0x1000-0x1fff]
[    0.296236] pci_bus 0000:03: resource 1 [mem 0x90500000-0x905fffff]
[    0.296240] pci_bus 0000:03: resource 2 [mem 0x90400000-0x904fffff 64bit pref]
[    0.296303] NET: Registered protocol family 2
[    0.296627] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.296788] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.296956] TCP: Hash tables configured (established 32768 bind 32768)
[    0.297023] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.297113] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.297251] NET: Registered protocol family 1
[    0.297283] pci 0000:00:02.0: Video device with shadowed ROM
[    0.297665] PCI: CLS 64 bytes, default 64
[    0.297781] Unpacking initramfs...
[    0.408220] Freeing initrd memory: 3540K (ffff880079151000 - ffff8800794c6000)
[    0.408240] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.408245] software IO TLB [mem 0x741af000-0x781af000] (64MB) mapped at [ffff8800741af000-ffff8800781aefff]
[    0.408464] microcode: CPU0 sig=0x30678, pf=0x8, revision=0x824
[    0.408482] microcode: CPU1 sig=0x30678, pf=0x8, revision=0x824
[    0.408501] microcode: CPU2 sig=0x30678, pf=0x8, revision=0x824
[    0.408519] microcode: CPU3 sig=0x30678, pf=0x8, revision=0x824
[    0.408632] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.408837] Scanning for low memory corruption every 60 seconds
[    0.409534] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.409566] Initialise system trusted keyring
[    0.410163] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.413719] zpool: loaded
[    0.413725] zbud: loaded
[    0.414071] VFS: Disk quotas dquot_6.6.0
[    0.414156] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.414497] Key type big_key registered
[    0.414895] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.414994] io scheduler noop registered
[    0.415001] io scheduler deadline registered
[    0.415076] io scheduler cfq registered (default)
[    0.415787] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.415803] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.415849] intel_idle: MWAIT substates: 0x33000020
[    0.415853] intel_idle: v0.4 model 0x37
[    0.415856] intel_idle: lapic_timer_reliable_states 0xffffffff
[    0.416319] GHES: HEST is not enabled!
[    0.416467] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.436784] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.438796] hpet: number irqs doesn't agree with number of timers
[    0.438838] Linux agpgart interface v0.103
[    0.439881] rtc_cmos 00:00: RTC can wake from S4
[    0.440547] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0
[    0.440579] rtc_cmos 00:00: alarms up to one month, y3k, 242 bytes nvram
[    0.440603] Intel P-state driver initializing.
[    0.441495] ledtrig-cpu: registered to indicate activity on CPUs
[    0.446558] NET: Registered protocol family 10
[    0.448511] NET: Registered protocol family 17
[    0.455006] Loading compiled-in X.509 certificates
[    0.455094] registered taskstats version 1
[    0.455152] zswap: loading zswap
[    0.455168] zswap: using zbud pool
[    0.455210] zswap: using lzo compressor
[    0.457639]   Magic number: 7:336:591
[    0.458053] rtc_cmos 00:00: setting system clock to 2015-11-21 16:35:49 UTC (1448123749)
[    0.458409] PM: Hibernation image not present or could not be loaded.
[    0.460056] Freeing unused kernel memory: 1180K (ffffffff818e8000 - ffffffff81a0f000)
[    0.460064] Write protecting the kernel read-only data: 8192k
[    0.462801] Freeing unused kernel memory: 520K (ffff88000157e000 - ffff880001600000)
[    0.463908] Freeing unused kernel memory: 280K (ffff8800017ba000 - ffff880001800000)
[    0.490112] random: systemd-tmpfile urandom read with 1 bits of entropy available
[    0.556370] sdhci: Secure Digital Host Controller Interface driver
[    0.556376] sdhci: Copyright(c) Pierre Ossman
[    0.565170] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    0.565175] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    0.565706] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.580293] sdhci-pci 0000:00:12.0: SDHCI controller found [8086:0f16] (rev e)
[    0.580518] sdhci-pci 0000:00:12.0: failed to setup card detect gpio
[    0.581542] sdhci-pci 0000:00:12.0: No vmmc regulator found
[    0.581547] sdhci-pci 0000:00:12.0: No vqmmc regulator found
[    0.582212] SCSI subsystem initialized
[    0.583089] ACPI: bus type USB registered
[    0.583148] usbcore: registered new interface driver usbfs
[    0.583171] usbcore: registered new interface driver hub
[    0.583237] usbcore: registered new device driver usb
[    0.586578] libata version 3.00 loaded.
[    0.587512] mmc0: SDHCI controller on PCI [0000:00:12.0] using ADMA
[    0.587552] sdhci-pci 0000:00:17.0: SDHCI controller found [8086:0f50] (rev e)
[    0.588771] sdhci-pci 0000:00:17.0: No vmmc regulator found
[    0.588776] sdhci-pci 0000:00:17.0: No vqmmc regulator found
[    0.592027] mmc1: SDHCI controller on PCI [0000:00:17.0] using ADMA
[    0.603610] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.603627] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    0.604034] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
[    0.604042] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    0.604680] hub 1-0:1.0: USB hub found
[    0.604700] hub 1-0:1.0: 6 ports detected
[    0.605480] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.605489] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    0.605862] hub 2-0:1.0: USB hub found
[    0.605878] hub 2-0:1.0: 1 port detected
[    0.606232] ahci 0000:00:13.0: version 3.0
[    0.606439] ahci 0000:00:13.0: controller can't do DEVSLP, turning off
[    0.619530] ahci 0000:00:13.0: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x1 impl SATA mode
[    0.619538] ahci 0000:00:13.0: flags: 64bit ncq pm led clo pio slum part deso 
[    0.620282] scsi host0: ahci
[    0.621133] scsi host1: ahci
[    0.621247] ata1: SATA max UDMA/133 abar m2048@0x9091e000 port 0x9091e100 irq 262
[    0.621251] ata2: DUMMY
[    0.656630] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.940177] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    0.941369] ata1.00: ATA-9: WDC WD5000LPVX-22V0TT0, 01.01A01, max UDMA/133
[    0.941376] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    0.942558] ata1.00: configured for UDMA/133
[    0.943781] scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000LPVX-2 1A01 PQ: 0 ANSI: 5
[    0.952486] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    0.952497] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    0.952682] sd 0:0:0:0: [sda] Write Protect is off
[    0.952688] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.952765] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.963887] usb 1-2: new high-speed USB device number 2 using xhci_hcd
[    1.022257]  sda: sda1
[    1.023507] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.144069] hub 1-2:1.0: USB hub found
[    1.144534] hub 1-2:1.0: 4 ports detected
[    1.146444] usb: failed to peer 1-2-port1 and usb2-port1 by location (1-2-port1:none) (usb2-port1:usb1-port1)
[    1.146453] usb 1-2-port1: failed to peer to usb2-port1 (-16)
[    1.146456] usb: port power management may be unreliable
[    1.146610] usb: failed to peer 1-2-port2 and usb2-port1 by location (1-2-port2:none) (usb2-port1:usb1-port1)
[    1.146615] usb 1-2-port2: failed to peer to usb2-port1 (-16)
[    1.146731] usb: failed to peer 1-2-port3 and usb2-port1 by location (1-2-port3:none) (usb2-port1:usb1-port1)
[    1.146736] usb 1-2-port3: failed to peer to usb2-port1 (-16)
[    1.146856] usb: failed to peer 1-2-port4 and usb2-port1 by location (1-2-port4:none) (usb2-port1:usb1-port1)
[    1.146861] usb 1-2-port4: failed to peer to usb2-port1 (-16)
[    1.310390] usb 1-4: new high-speed USB device number 3 using xhci_hcd
[    1.406833] tsc: Refined TSC clocksource calibration: 1833.333 MHz
[    1.406841] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x34da54753aa, max_idle_ns: 881590618787 ns
[    1.550596] usb 1-2.1: new full-speed USB device number 4 using xhci_hcd
[    1.704036] usb 1-2.2: new low-speed USB device number 5 using xhci_hcd
[    1.791353] usb 1-2.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[    1.800622] hidraw: raw HID events driver (C) Jiri Kosina
[    1.807052] usbcore: registered new interface driver usbhid
[    1.807058] usbhid: USB HID core driver
[    2.409522] clocksource: Switched to clocksource tsc
[    4.350622] random: nonblocking pool is initialized
[   11.129305] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[   11.991867] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.071612] systemd[1]: systemd 227 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
[   12.071925] systemd[1]: Detected architecture x86-64.
[   12.098704] systemd[1]: Set hostname to <dario>.
[   13.322042] systemd[1]: Listening on udev Kernel Socket.
[   13.322576] systemd[1]: Listening on Journal Socket.
[   13.322964] systemd[1]: Listening on LVM2 metadata daemon socket.
[   13.323361] systemd[1]: Listening on Journal Socket (/dev/log).
[   13.385972] systemd[1]: Created slice User and Session Slice.
[   13.386468] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[   13.386982] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[   13.387419] systemd[1]: Listening on udev Control Socket.
[   13.388021] systemd[1]: Created slice System Slice.
[   13.388397] systemd[1]: Reached target Slices.
[   13.389982] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[   13.436759] systemd[1]: Starting Setup Virtual Console...
[   13.438239] systemd[1]: Mounting Debug File System...
[   13.439712] systemd[1]: Starting Journal Service...
[   13.441250] systemd[1]: Mounting Configuration File System...
[   13.442577] systemd[1]: Mounting POSIX Message Queue File System...
[   13.470680] systemd[1]: Mounting Temporary Directory...
[   13.472062] systemd[1]: Mounting Huge Pages File System...
[   13.472632] systemd[1]: Created slice system-getty.slice.
[   13.473005] systemd[1]: Reached target Swap.
[   13.473500] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   13.473863] systemd[1]: Reached target Encrypted Volumes.
[   13.474219] systemd[1]: Reached target Remote File Systems.
[   13.474684] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   13.475045] systemd[1]: Reached target Login Prompts.
[   13.475664] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   13.507956] systemd[1]: Reached target Paths.
[   13.509387] systemd[1]: Starting Remount Root and Kernel File Systems...
[   13.510787] systemd[1]: Starting Apply Kernel Variables...
[   13.514470] systemd[1]: Started Create list of required static device nodes for the current kernel.
[   13.651985] systemd[1]: Mounted Configuration File System.
[   13.652475] systemd[1]: Mounted POSIX Message Queue File System.
[   13.652878] systemd[1]: Mounted Debug File System.
[   13.653269] systemd[1]: Mounted Huge Pages File System.
[   13.653679] systemd[1]: Mounted Temporary Directory.
[   13.660343] systemd[1]: Started Setup Virtual Console.
[   13.679288] EXT4-fs (sda1): re-mounted. Opts: data=ordered
[   13.680647] systemd[1]: Started Remount Root and Kernel File Systems.
[   13.682372] systemd[1]: Starting Create Static Device Nodes in /dev...
[   13.684138] systemd[1]: Starting udev Coldplug all Devices...
[   13.685607] systemd[1]: Starting Load/Save Random Seed...
[   13.835281] systemd[1]: Started Load/Save Random Seed.
[   14.265456] systemd[1]: Started udev Coldplug all Devices.
[   14.270340] systemd[1]: Started Apply Kernel Variables.
[   14.318419] systemd[1]: Started Create Static Device Nodes in /dev.
[   14.320022] systemd[1]: Starting udev Kernel Device Manager...
[   14.320332] systemd[1]: Reached target Local File Systems (Pre).
[   14.320731] systemd[1]: Reached target Local File Systems.
[   15.775341] systemd[1]: Started udev Kernel Device Manager.
[   15.788573] systemd[1]: Started Journal Service.
[   15.979666] systemd-journald[152]: Received request to flush runtime journal from PID 1
[   16.536280] wmi: Mapper loaded
[   17.265464] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[   17.265477] ACPI: Power Button [PWRB]
[   17.265600] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[   17.265609] ACPI: Sleep Button [SLPB]
[   17.265742] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[   17.265806] ACPI: Lid Switch [LID]
[   17.265933] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[   17.265941] ACPI: Power Button [PWRF]
[   18.008626] ACPI: AC Adapter [ACAD] (on-line)
[   18.176851] ACPI Warning: SystemIO range 0x0000000000002000-0x000000000000201F conflicts with OpRegion 0x0000000000002000-0x000000000000200F (\_SB_.PCI0.SBUS.SMBI) (20150619/utaddress-254)
[   18.176863] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   18.219177] ACPI: Battery Slot [BAT1] (battery present)
[   18.237089] [drm] Initialized drm 1.1.0 20060810
[   18.315318] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   18.340635] thermal LNXTHERM:00: registered as thermal_zone2
[   18.340642] ACPI: Thermal Zone [TZ01] (42 C)
[   18.539591] input: PC Speaker as /devices/platform/pcspkr/input/input5
[   18.884883] dw_dmac INTL9C60:01: DesignWare DMA Controller, 8 channels
[   18.926347] i2c_hid i2c-SYN1B7D:01: failed to retrieve report from device.
[   18.930867] [drm] Memory usable by graphics device = 2048M
[   18.930874] [drm] Replacing VGA console driver
[   18.931846] Console: switching to colour dummy device 80x25
[   18.932825] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   18.932829] [drm] Driver supports precise vblank timestamp query.
[   18.933909] i2c_hid i2c-SYN1B7D:01: failed to retrieve report from device.
[   18.934807] i2c_hid i2c-SYN1B7D:01: failed to retrieve report from device.                                                                                                                   
[   18.935706] i2c_hid i2c-SYN1B7D:01: failed to retrieve report from device.                                                                                                                   
[   18.936578] i2c_hid i2c-SYN1B7D:01: failed to retrieve report from device.                                                                                                                   
[   18.936834] input: SYN1B7D:01 06CB:2991 UNKNOWN as /devices/platform/80860F41:00/i2c-0/i2c-SYN1B7D:01/0018:06CB:2991.0002/input/input6
[   18.937025] hid-multitouch 0018:06CB:2991.0002: input,hidraw0: <UNKNOWN> HID v1.00 Mouse [SYN1B7D:01 06CB:2991] on 
[   18.942013] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[   18.942038] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[   18.945347] iTCO_vendor_support: vendor-support=0
[   18.948728] r8169 0000:03:00.0 eth0: RTL8168g/8111g at 0xffffc90000668000, c4:54:44:cf:00:e9, XID 0c000800 IRQ 265
[   18.948734] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[   18.979824] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   19.011866] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   19.012304] fbcon: inteldrmfb (fb0) is primary device
[   19.012457] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
[   19.012652] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[   19.012657] [drm] Initialized i915 1.6.0 20150522 for 0000:00:02.0 on minor 0
[   19.031551] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   19.031634] iTCO_wdt: Found a Bay Trail SoC TCO device (Version=3, TCOBASE=0x0460)
[   19.031833] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   19.052191] acer_wmi: Acer Laptop ACPI-WMI Extras
[   19.052207] acer_wmi: Function bitmap for Communication Button: 0x801
[   19.056591] acer_wmi: Enabling Launch Manager failed: 0xe4 - 0x0
[   19.056713] input: Acer WMI hotkeys as /devices/virtual/input/input9
[   19.057329] input: Acer BMA150 accelerometer as /devices/virtual/input/input10
[   19.668462] r8169 0000:03:00.0 enp3s0: renamed from eth0
[   19.689234] mousedev: PS/2 mouse device common for all mice
[   19.700610] ath: phy0: WB335 2-ANT card detected
[   19.700612] ath: phy0: Set BT/WLAN RX diversity capability
[   19.707115] ath: phy0: Enable LNA combining
[   19.708273] ath: phy0: ASPM enabled: 0x42
[   19.708276] ath: EEPROM regdomain: 0x65
[   19.708277] ath: EEPROM indicates we should expect a direct regpair map
[   19.708279] ath: Country alpha2 being used: 00
[   19.708279] ath: Regpair used: 0x65
[   19.774428] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   19.775051] ieee80211 phy0: Atheros AR9565 Rev:1 mem=0xffffc90000c00000, irq=17
[   19.777508] input: USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.2/1-2.2:1.0/0003:1BCF:0007.0001/input/input11
[   19.777942] hid-generic 0003:1BCF:0007.0001: input,hiddev0,hidraw1: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:14.0-2.2/input0
[   19.807584] intel_rapl: Found RAPL domain package
[   19.807592] intel_rapl: Found RAPL domain core
[   19.847248] media: Linux media interface: v0.10
[   19.889157] Bluetooth: Core ver 2.20
[   19.889184] NET: Registered protocol family 31
[   19.889185] Bluetooth: HCI device and connection manager initialized
[   19.889191] Bluetooth: HCI socket layer initialized
[   19.889194] Bluetooth: L2CAP socket layer initialized
[   19.889204] Bluetooth: SCO socket layer initialized
[   19.896379] ath9k 0000:02:00.0 wlp2s0: renamed from wlan0
[   19.922740] Linux video capture interface: v2.00
[   20.020837] uvcvideo: Found UVC 1.00 device HD WebCam (04f2:b469)
[   20.028615] input: HD WebCam as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/input/input12
[   20.028888] usbcore: registered new interface driver uvcvideo
[   20.028889] USB Video Class driver (1.1.1)
[   20.086473] usbcore: registered new interface driver btusb
[   20.205217] usbcore: registered new interface driver ath3k
[   20.335733] usb 1-2.1: USB disconnect, device number 4
[   20.522709] usb 1-2.1: new full-speed USB device number 6 using xhci_hcd
[   20.596495] Console: switching to colour frame buffer device 170x48
[   20.613569] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[   20.613577] i915 0000:00:02.0: registered panic notifier
[   21.016847] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC283: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   21.016855] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   21.016859] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[   21.016863] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   21.016866] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   21.016870] snd_hda_codec_realtek hdaudioC0D0:      Mic=0x12
[   21.192742] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[   21.192928] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[   24.221912] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   24.233967] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   24.236849] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[   24.381434] r8169 0000:03:00.0 enp3s0: link down
[   24.381503] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[   25.121381] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[   27.248137] wlp2s0: authenticate with dc:53:7c:82:71:80
[   27.260036] wlp2s0: send auth to dc:53:7c:82:71:80 (try 1/3)
[   27.263606] wlp2s0: authenticated
[   27.264506] wlp2s0: associate with dc:53:7c:82:71:80 (try 1/3)
[   27.271318] wlp2s0: RX AssocResp from dc:53:7c:82:71:80 (capab=0x411 status=0 aid=3)
[   27.271403] wlp2s0: associated
[   27.271450] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[   27.655170] sha256_ssse3: Using SSSE3 optimized SHA-256 implementation
[   27.869081] systemd-journald[152]: File /var/log/journal/1ca4e7b412784cf990680633012cf599/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.

Lone_Wolf · 2015-11-22 14:24:28

[    0.408464] microcode: CPU0 sig=0x30678, pf=0x8, revision=0x824
[    0.408482] microcode: CPU1 sig=0x30678, pf=0x8, revision=0x824
[    0.408501] microcode: CPU2 sig=0x30678, pf=0x8, revision=0x824
[    0.408519] microcode: CPU3 sig=0x30678, pf=0x8, revision=0x824
[    0.408632] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba

This indicates you don't use early intel microcode update, see https://wiki.archlinux.org/index.php/Microcode .

There are some errors in dmesg, but none that really stand out.

[   310.754] (EE) Please also check the log file at "~/.local/share/xorg/Xorg.0.log" for additional information.

post the contents of that file also.

How do you start X , do you use a displaymanager or startx/ .xinitrc ?

dkl · 2015-11-23 17:58:06

I activated microcode updates, but it does not seem to change anything obvious so far.

The content of ~/.local/share/xorg/Xorg.0.log:

[   310.753] _XSERVTransSocketUNIXCreateListener: ...SocketCreateListener() failed
[   310.753] _XSERVTransMakeAllCOTSServerListeners: server already running
[   310.753] (EE) 
Fatal server error:
[   310.753] (EE) Cannot establish any listening sockets - Make sure an X server isn't already running(EE) 
[   310.754] (EE) 
Please consult the The X.Org Foundation support 
	 at http://wiki.x.org
 for help. 
[   310.754] (EE) Please also check the log file at "/home/dario/.local/share/xorg/Xorg.0.log" for additional information.
[   310.754] (EE) 
[   310.754] (EE) Server terminated with error (1). Closing log file.

I use the displaymanager SDDM.

Xabre · 2015-11-23 18:36:12

If you use sddm, log is in /var/log/Xorg.0.log

dkl · 2015-11-26 20:41:03

In the file /var/log/Xorg.0.log there is:

[    19.586] 
X.Org X Server 1.18.0
Release Date: 2015-11-09
[    19.586] X Protocol Version 11, Revision 0
[    19.586] Build Operating System: Linux 4.2.3-1-ARCH x86_64 
[    19.586] Current Operating System: Linux dariosNetbook 4.2.5-1-ARCH #1 SMP PREEMPT Tue Oct 27 08:13:28 CET 2015 x86_64
[    19.586] Kernel command line: BOOT_IMAGE=../vmlinuz-linux root=/dev/sda1 rw intel_pstate=disable initrd=../intel-ucode.img,../initramfs-linux.img
[    19.587] Build Date: 18 November 2015  08:07:09AM
[    19.587]  
[    19.587] Current version of pixman: 0.32.8
[    19.587] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[    19.587] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    19.587] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Nov 26 21:28:13 2015
[    19.665] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    19.758] (==) No Layout section.  Using the first Screen section.
[    19.758] (==) No screen section available. Using defaults.
[    19.758] (**) |-->Screen "Default Screen Section" (0)
[    19.758] (**) |   |-->Monitor "<default monitor>"
[    19.765] (==) No monitor specified for screen "Default Screen Section".
	Using a default monitor configuration.
[    19.765] (==) Automatically adding devices
[    19.765] (==) Automatically enabling devices
[    19.765] (==) Automatically adding GPU devices
[    19.765] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    19.799] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[    19.799] 	Entry deleted from font path.
[    19.808] (==) FontPath set to:
	/usr/share/fonts/misc/,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/OTF/,
	/usr/share/fonts/100dpi/,
	/usr/share/fonts/75dpi/
[    19.808] (==) ModulePath set to "/usr/lib/xorg/modules"
[    19.808] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[    19.808] (II) Loader magic: 0x819d40
[    19.808] (II) Module ABI versions:
[    19.808] 	X.Org ANSI C Emulation: 0.4
[    19.808] 	X.Org Video Driver: 20.0
[    19.808] 	X.Org XInput driver : 22.1
[    19.808] 	X.Org Server Extension : 9.0
[    19.809] (++) using VT number 1

[    19.809] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[    19.810] (II) xfree86: Adding drm device (/dev/dri/card0)
[    19.816] (--) PCI:*(0:0:2:0) 8086:0f31:1025:0933 rev 14, Mem @ 0x90000000/4194304, 0x80000000/268435456, I/O @ 0x00002050/8
[    19.816] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[    19.840] (II) LoadModule: "glx"
[    19.855] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    20.354] (II) Module glx: vendor="X.Org Foundation"
[    20.354] 	compiled for 1.18.0, module version = 1.0.0
[    20.354] 	ABI class: X.Org Server Extension, version 9.0
[    20.354] (==) AIGLX enabled
[    20.354] (==) Matched intel as autoconfigured driver 0
[    20.354] (==) Matched intel as autoconfigured driver 1
[    20.354] (==) Matched modesetting as autoconfigured driver 2
[    20.354] (==) Matched fbdev as autoconfigured driver 3
[    20.354] (==) Matched vesa as autoconfigured driver 4
[    20.354] (==) Assigned the driver to the xf86ConfigLayout
[    20.354] (II) LoadModule: "intel"
[    20.467] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[    20.600] (II) Module intel: vendor="X.Org Foundation"
[    20.600] 	compiled for 1.18.0, module version = 2.99.917
[    20.600] 	Module class: X.Org Video Driver
[    20.600] 	ABI class: X.Org Video Driver, version 20.0
[    20.600] (II) LoadModule: "modesetting"
[    20.600] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[    20.611] (II) Module modesetting: vendor="X.Org Foundation"
[    20.611] 	compiled for 1.18.0, module version = 1.18.0
[    20.611] 	Module class: X.Org Video Driver
[    20.611] 	ABI class: X.Org Video Driver, version 20.0
[    20.611] (II) LoadModule: "fbdev"
[    20.611] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    20.627] (II) Module fbdev: vendor="X.Org Foundation"
[    20.627] 	compiled for 1.18.0, module version = 0.4.4
[    20.627] 	Module class: X.Org Video Driver
[    20.627] 	ABI class: X.Org Video Driver, version 20.0
[    20.627] (II) LoadModule: "vesa"
[    20.627] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    20.634] (II) Module vesa: vendor="X.Org Foundation"
[    20.634] 	compiled for 1.18.0, module version = 2.3.4
[    20.634] 	Module class: X.Org Video Driver
[    20.634] 	ABI class: X.Org Video Driver, version 20.0
[    20.634] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
	i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
	915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
	Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
	GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[    20.635] (II) intel: Driver for Intel(R) HD Graphics: 2000-6000
[    20.635] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100, 6100
[    20.635] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200, 6200, P6300
[    20.635] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[    20.635] (II) FBDEV: driver for framebuffer: fbdev
[    20.635] (II) VESA: driver for VESA chipsets: vesa
[    20.647] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 20150522
[    20.647] (II) intel(0): SNA compiled from 2.99.917-478-gdf72bc5
[    20.649] (WW) Falling back to old probe method for modesetting
[    20.649] (WW) Falling back to old probe method for fbdev
[    20.649] (II) Loading sub module "fbdevhw"
[    20.649] (II) LoadModule: "fbdevhw"
[    20.650] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    20.661] (II) Module fbdevhw: vendor="X.Org Foundation"
[    20.661] 	compiled for 1.18.0, module version = 0.0.2
[    20.661] 	ABI class: X.Org Video Driver, version 20.0
[    20.661] (WW) Falling back to old probe method for vesa
[    20.662] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics
[    20.662] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2; using a maximum of 4 threads
[    20.662] (II) intel(0): Creating default Display subsection in Screen section
	"Default Screen Section" for depth/fbbpp 24/32
[    20.662] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[    20.662] (==) intel(0): RGB weight 888
[    20.662] (==) intel(0): Default visual is TrueColor
[    20.666] (II) intel(0): Output eDP1 has no monitor section
[    20.674] (--) intel(0): Found backlight control interface intel_backlight (type 'raw') for output eDP1
[    20.674] (II) intel(0): Enabled output eDP1
[    20.674] (--) intel(0): Using a maximum size of 256x256 for hardware cursors
[    20.675] (II) intel(0): Output VIRTUAL1 has no monitor section
[    20.675] (II) intel(0): Enabled output VIRTUAL1
[    20.675] (--) intel(0): Output eDP1 using initial mode 1366x768 on pipe 0
[    20.675] (==) intel(0): TearFree disabled
[    20.675] (==) intel(0): DPI set to (96, 96)
[    20.675] (II) Loading sub module "dri2"
[    20.676] (II) LoadModule: "dri2"
[    20.676] (II) Module "dri2" already built-in
[    20.676] (II) Loading sub module "present"
[    20.676] (II) LoadModule: "present"
[    20.676] (II) Module "present" already built-in
[    20.676] (II) UnloadModule: "modesetting"
[    20.676] (II) Unloading modesetting
[    20.676] (II) UnloadModule: "fbdev"
[    20.676] (II) Unloading fbdev
[    20.676] (II) UnloadSubModule: "fbdevhw"
[    20.677] (II) Unloading fbdevhw
[    20.677] (II) UnloadModule: "vesa"
[    20.677] (II) Unloading vesa
[    20.677] (==) Depth 24 pixmap format is 32 bpp
[    20.715] (II) intel(0): SNA initialized with Baytrail (gen7) backend
[    20.715] (==) intel(0): Backing store enabled
[    20.715] (==) intel(0): Silken mouse enabled
[    20.717] (II) intel(0): HW Cursor enabled
[    20.717] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    20.718] (==) intel(0): DPMS enabled
[    20.720] (==) intel(0): Display hotplug detection enabled
[    20.720] (II) intel(0): [DRI2] Setup complete
[    20.720] (II) intel(0): [DRI2]   DRI driver: i965
[    20.720] (II) intel(0): [DRI2]   VDPAU driver: va_gl
[    20.720] (II) intel(0): direct rendering: DRI2 enabled
[    20.720] (II) intel(0): hardware support for Present enabled
[    20.720] (--) RandR disabled
[    20.880] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    20.880] (II) AIGLX: enabled GLX_ARB_create_context
[    20.880] (II) AIGLX: enabled GLX_ARB_create_context_profile
[    20.880] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[    20.880] (II) AIGLX: enabled GLX_INTEL_swap_event
[    20.880] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[    20.880] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[    20.880] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[    20.880] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    20.880] (II) AIGLX: enabled GLX_ARB_create_context_robustness
[    20.880] (II) AIGLX: Loaded and initialized i965
[    20.880] (II) GLX: Initialized DRI2 GL provider for screen 0
[    20.916] (II) intel(0): switch to mode 1366x768@60.0 on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none
[    20.916] (II) intel(0): Setting screen physical size to 361 x 203
[    21.328] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[    21.329] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    21.329] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    21.329] (II) LoadModule: "libinput"
[    21.339] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    21.377] (II) Module libinput: vendor="X.Org Foundation"
[    21.377] 	compiled for 1.18.0, module version = 0.15.0
[    21.377] 	Module class: X.Org XInput Driver
[    21.377] 	ABI class: X.Org XInput driver, version 22.1
[    21.377] (II) Using input driver 'libinput' for 'Power Button'
[    21.377] (**) Power Button: always reports core events
[    21.377] (**) Option "Device" "/dev/input/event4"
[    21.378] (II) input device 'Power Button', /dev/input/event4 is tagged by udev as: Keyboard
[    21.378] (II) input device 'Power Button', /dev/input/event4 is a keyboard
[    21.390] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[    21.390] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    21.392] (II) input device 'Power Button', /dev/input/event4 is tagged by udev as: Keyboard
[    21.392] (II) input device 'Power Button', /dev/input/event4 is a keyboard
[    21.394] (II) config/udev: Adding input device Video Bus (/dev/input/event7)
[    21.394] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    21.395] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[    21.395] (II) Using input driver 'libinput' for 'Video Bus'
[    21.395] (**) Video Bus: always reports core events
[    21.395] (**) Option "Device" "/dev/input/event7"
[    21.396] (II) input device 'Video Bus', /dev/input/event7 is tagged by udev as: Keyboard
[    21.396] (II) input device 'Video Bus', /dev/input/event7 is a keyboard
[    21.414] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8/event7"
[    21.414] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    21.418] (II) input device 'Video Bus', /dev/input/event7 is tagged by udev as: Keyboard
[    21.418] (II) input device 'Video Bus', /dev/input/event7 is a keyboard
[    21.421] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[    21.421] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    21.421] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    21.421] (II) Using input driver 'libinput' for 'Power Button'
[    21.421] (**) Power Button: always reports core events
[    21.422] (**) Option "Device" "/dev/input/event1"
[    21.424] (II) input device 'Power Button', /dev/input/event1 is tagged by udev as: Keyboard
[    21.424] (II) input device 'Power Button', /dev/input/event1 is a keyboard
[    21.440] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1/event1"
[    21.440] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    21.444] (II) input device 'Power Button', /dev/input/event1 is tagged by udev as: Keyboard
[    21.444] (II) input device 'Power Button', /dev/input/event1 is a keyboard
[    21.445] (II) config/udev: Adding input device Lid Switch (/dev/input/event3)
[    21.445] (II) No input driver specified, ignoring this device.
[    21.445] (II) This device may have been added with another device file.
[    21.447] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[    21.447] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[    21.447] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[    21.447] (II) Using input driver 'libinput' for 'Sleep Button'
[    21.447] (**) Sleep Button: always reports core events
[    21.447] (**) Option "Device" "/dev/input/event2"
[    21.448] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard
[    21.448] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard
[    21.460] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2/event2"
[    21.460] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[    21.462] (II) input device 'Sleep Button', /dev/input/event2 is tagged by udev as: Keyboard
[    21.462] (II) input device 'Sleep Button', /dev/input/event2 is a keyboard
[    21.466] (II) config/udev: Adding input device USB Optical Mouse (/dev/input/event10)
[    21.466] (**) USB Optical Mouse: Applying InputClass "evdev pointer catchall"
[    21.466] (**) USB Optical Mouse: Applying InputClass "libinput pointer catchall"
[    21.466] (II) Using input driver 'libinput' for 'USB Optical Mouse'
[    21.466] (**) USB Optical Mouse: always reports core events
[    21.466] (**) Option "Device" "/dev/input/event10"
[    21.522] (II) input device 'USB Optical Mouse', /dev/input/event10 is tagged by udev as: Mouse
[    21.522] (II) input device 'USB Optical Mouse', /dev/input/event10 is a pointer caps
[    21.551] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.2/1-2.2:1.0/0003:1BCF:0007.0001/input/input11/event10"
[    21.551] (II) XINPUT: Adding extended input device "USB Optical Mouse" (type: MOUSE, id 10)
[    21.553] (**) Option "AccelerationScheme" "none"
[    21.554] (**) USB Optical Mouse: (accel) selected scheme none/0
[    21.554] (**) USB Optical Mouse: (accel) acceleration factor: 2.000
[    21.554] (**) USB Optical Mouse: (accel) acceleration threshold: 4
[    21.608] (II) input device 'USB Optical Mouse', /dev/input/event10 is tagged by udev as: Mouse
[    21.608] (II) input device 'USB Optical Mouse', /dev/input/event10 is a pointer caps
[    21.612] (II) config/udev: Adding input device USB Optical Mouse (/dev/input/mouse1)
[    21.612] (II) No input driver specified, ignoring this device.
[    21.612] (II) This device may have been added with another device file.
[    21.614] (II) config/udev: Adding input device HD WebCam (/dev/input/event11)
[    21.614] (**) HD WebCam: Applying InputClass "evdev keyboard catchall"
[    21.614] (**) HD WebCam: Applying InputClass "libinput keyboard catchall"
[    21.614] (II) Using input driver 'libinput' for 'HD WebCam'
[    21.614] (**) HD WebCam: always reports core events
[    21.614] (**) Option "Device" "/dev/input/event11"
[    21.615] (II) input device 'HD WebCam', /dev/input/event11 is tagged by udev as: Keyboard
[    21.615] (II) input device 'HD WebCam', /dev/input/event11 is a keyboard
[    21.647] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/input/input12/event11"
[    21.647] (II) XINPUT: Adding extended input device "HD WebCam" (type: KEYBOARD, id 11)
[    21.650] (II) input device 'HD WebCam', /dev/input/event11 is tagged by udev as: Keyboard
[    21.650] (II) input device 'HD WebCam', /dev/input/event11 is a keyboard
[    21.652] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event12)
[    21.652] (II) No input driver specified, ignoring this device.
[    21.652] (II) This device may have been added with another device file.
[    21.654] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event13)
[    21.654] (II) No input driver specified, ignoring this device.
[    21.655] (II) This device may have been added with another device file.
[    21.656] (II) config/udev: Adding input device SYN1B7D:01 06CB:2991 UNKNOWN (/dev/input/event6)
[    21.656] (**) SYN1B7D:01 06CB:2991 UNKNOWN: Applying InputClass "evdev touchpad catchall"
[    21.656] (**) SYN1B7D:01 06CB:2991 UNKNOWN: Applying InputClass "touchpad catchall"
[    21.656] (**) SYN1B7D:01 06CB:2991 UNKNOWN: Applying InputClass "Default clickpad buttons"
[    21.656] (**) SYN1B7D:01 06CB:2991 UNKNOWN: Applying InputClass "libinput touchpad catchall"
[    21.656] (II) Using input driver 'libinput' for 'SYN1B7D:01 06CB:2991 UNKNOWN'
[    21.656] (**) SYN1B7D:01 06CB:2991 UNKNOWN: always reports core events
[    21.656] (**) Option "Device" "/dev/input/event6"
[    21.672] (II) input device 'SYN1B7D:01 06CB:2991 UNKNOWN', /dev/input/event6 is tagged by udev as: Touchpad
[    21.673] (II) input device 'SYN1B7D:01 06CB:2991 UNKNOWN', /dev/input/event6 is a touchpad
[    21.711] (**) Option "config_info" "udev:/sys/devices/platform/80860F41:00/i2c-0/i2c-SYN1B7D:01/0018:06CB:2991.0002/input/input6/event6"
[    21.711] (II) XINPUT: Adding extended input device "SYN1B7D:01 06CB:2991 UNKNOWN" (type: TOUCHPAD, id 12)
[    21.713] (**) Option "AccelerationScheme" "none"
[    21.713] (**) SYN1B7D:01 06CB:2991 UNKNOWN: (accel) selected scheme none/0
[    21.713] (**) SYN1B7D:01 06CB:2991 UNKNOWN: (accel) acceleration factor: 2.000
[    21.714] (**) SYN1B7D:01 06CB:2991 UNKNOWN: (accel) acceleration threshold: 4
[    21.717] (II) input device 'SYN1B7D:01 06CB:2991 UNKNOWN', /dev/input/event6 is tagged by udev as: Touchpad
[    21.717] (II) input device 'SYN1B7D:01 06CB:2991 UNKNOWN', /dev/input/event6 is a touchpad
[    21.719] (II) config/udev: Adding input device SYN1B7D:01 06CB:2991 UNKNOWN (/dev/input/mouse0)
[    21.719] (**) SYN1B7D:01 06CB:2991 UNKNOWN: Ignoring device from InputClass "touchpad ignore duplicates"
[    21.721] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    21.721] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    21.721] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    21.721] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[    21.722] (**) AT Translated Set 2 keyboard: always reports core events
[    21.722] (**) Option "Device" "/dev/input/event0"
[    21.724] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[    21.724] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard
[    21.757] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    21.757] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 13)
[    21.760] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[    21.760] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard
[    21.762] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[    21.762] (II) No input driver specified, ignoring this device.
[    21.763] (II) This device may have been added with another device file.
[    21.765] (II) config/udev: Adding input device Acer BMA150 accelerometer (/dev/input/event9)
[    21.765] (II) No input driver specified, ignoring this device.
[    21.765] (II) This device may have been added with another device file.
[    21.766] (II) config/udev: Adding input device Acer BMA150 accelerometer (/dev/input/js0)
[    21.766] (II) No input driver specified, ignoring this device.
[    21.766] (II) This device may have been added with another device file.
[    21.767] (II) config/udev: Adding input device Acer WMI hotkeys (/dev/input/event8)
[    21.767] (**) Acer WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[    21.767] (**) Acer WMI hotkeys: Applying InputClass "libinput keyboard catchall"
[    21.767] (II) Using input driver 'libinput' for 'Acer WMI hotkeys'
[    21.767] (**) Acer WMI hotkeys: always reports core events
[    21.767] (**) Option "Device" "/dev/input/event8"
[    21.768] (II) input device 'Acer WMI hotkeys', /dev/input/event8 is tagged by udev as: Keyboard
[    21.768] (II) input device 'Acer WMI hotkeys', /dev/input/event8 is a keyboard
[    21.780] (**) Option "config_info" "udev:/sys/devices/virtual/input/input9/event8"
[    21.780] (II) XINPUT: Adding extended input device "Acer WMI hotkeys" (type: KEYBOARD, id 14)
[    21.782] (II) input device 'Acer WMI hotkeys', /dev/input/event8 is tagged by udev as: Keyboard
[    21.782] (II) input device 'Acer WMI hotkeys', /dev/input/event8 is a keyboard
[    35.701] (II) intel(0): EDID vendor "AUO", prod id 8540
[    35.701] (II) intel(0): Printing DDC gathered Modelines:
[    35.701] (II) intel(0): Modeline "1366x768"x0.0   75.60  1366 1404 1426 1592  768 771 777 790 -hsync -vsync (47.5 kHz eP)

Arch Linux

#1 2015-11-20 19:02:33

External Monitor not detected (Intel Graphics Card)

#2 2015-11-20 19:04:31

Re: External Monitor not detected (Intel Graphics Card)

#3 2015-11-20 19:13:59

Re: External Monitor not detected (Intel Graphics Card)

#4 2015-11-21 13:56:31

Re: External Monitor not detected (Intel Graphics Card)

#5 2015-11-21 16:40:21

Re: External Monitor not detected (Intel Graphics Card)

#6 2015-11-22 14:24:28

Re: External Monitor not detected (Intel Graphics Card)

#7 2015-11-23 17:58:06

Re: External Monitor not detected (Intel Graphics Card)

#8 2015-11-23 18:36:12

Re: External Monitor not detected (Intel Graphics Card)

#9 2015-11-26 20:41:03

Re: External Monitor not detected (Intel Graphics Card)

Board footer