You are not logged in.
- Topics: Active | Unanswered
Pages: 1
#1 2015-12-08 09:42:03
- cprussin
- Member
- Registered: 2010-07-20
- Posts: 9
nvidia output off center
So, I'm having an issue with the nvidia driver. The machine has a GeForce GTX 970, and is being used as an HDTV/gaming machine. I've got it run through an Onkyo TX NR-626 receiver. When I am using the nvidia driver and I have the output set to 1080p, the output on my screen is offset to the left about two inches and up about a centimeter, with a black bar on the right side and bottom and the left side cut off and a sliver of the top cut off--almost as if there were an overscan.
I've tried a whole lot of different things with some really interesting (weird) results:
- With a resolution below 1080p, the display is correct and aligned centered.
- When I change Color Space to YCbCr444 in nvidia-settings > GP 0 > DFP-1 > Controls, the black bars on the right and bottom turn dark green.
- With nouveau, the display is correct. (Note that the EDID reported by xrandr with nouveau matches the one reported when using nvidia)
- If I switch to another TTY running a terminal, the display is correct.
- When I run the computer directly to the TV and skip the receiver, the display is correct.
- When I replace the card with a GeForce GTX-750SC and use the nvidia-304xx drivers, the display is correct.
- When I use the same GTX-750SC with the nvidia driver, the display is incorrect and shows the same offset.
I highly doubt this is truly an overscan issue, not only because the problem goes away on other drivers, but also as I've fiddled with my TV and receiver settings to no end and am 99.99999% sure they are both properly configured for 1:1 mapping. It seems to be a problem with specifically the combination of the nvidia driver and the receiver, as weird as that sounds. Note that I've put loads of sources including many different computers thorough this receiver and never had problems before.
I've pretty much exhausted all my ideas. Does anyone have any ideas that are worth trying?
Some info:
xrandr --verbose
Screen 0: minimum 8 x 8, current 1920 x 1080, maximum 16384 x 16384
DVI-I-0 disconnected primary (normal left inverted right x axis y axis)
Identifier: 0x1be
Timestamp: 8595
Subpixel: unknown
Clones:
CRTCs: 0 1 2 3
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BorderDimensions: 4
supported: 4
Border: 0 0 0 0
range: (0, 65535)
SignalFormat: VGA
supported: VGA
ConnectorType: DVI-I
ConnectorNumber: 0
_ConnectorLocation: 0
DVI-I-1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x1bf
Timestamp: 8595
Subpixel: unknown
Clones:
CRTCs: 0 1 2 3
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BorderDimensions: 4
supported: 4
Border: 0 0 0 0
range: (0, 65535)
SignalFormat: TMDS
supported: TMDS
ConnectorType: DVI-I
ConnectorNumber: 0
_ConnectorLocation: 0
HDMI-0 connected 1920x1080+0+0 (0x1c1) normal (normal left inverted right x axis y axis) 160mm x 90mm
Identifier: 0x1c0
Timestamp: 8595
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1 2 3
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff003dcb610d00000000
00170103801009780aee91a3544c9926
0f5054bdef80714f81c0810081809500
a9c0b3000101023a801871382d40582c
4500a05a0000001e662156aa51001e30
468f3300a05a0000001e000000fc0054
582d4e523632360a20202020000000fd
00184b0f5116000a2020202020200175
020339f1479004050320220738097f07
0f7f071707503f06c04d02005706005f
7e01675400834f00006c030c001500b8
2dc000000000e2000f011d8018711c16
20582c2500a05a0000009e011d007251
d01e206e285500a05a0000001e8c0ad0
8a20e02d10103e9600a05a0000001800
000000000000000000000000000000ca
BorderDimensions: 4
supported: 4
Border: 0 0 0 0
range: (0, 65535)
SignalFormat: TMDS
supported: TMDS
ConnectorType: HDMI
ConnectorNumber: 2
_ConnectorLocation: 2
1920x1080 (0x1c1) 148.500MHz +HSync +VSync *current +preferred
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 67.50KHz
v: height 1080 start 1084 end 1089 total 1125 clock 60.00Hz
1920x1080 (0x1c2) 148.350MHz +HSync +VSync
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 67.43KHz
v: height 1080 start 1084 end 1089 total 1125 clock 59.94Hz
1920x1080 (0x1c3) 74.180MHz +HSync +VSync
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 33.72KHz
v: height 1080 start 1084 end 1089 total 1125 clock 29.97Hz
1920x1080 (0x1c4) 74.160MHz +HSync +VSync
h: width 1920 start 2558 end 2602 total 2750 skew 0 clock 26.97KHz
v: height 1080 start 1084 end 1089 total 1125 clock 23.97Hz
1920x1080 (0x1c5) 74.250MHz +HSync +VSync Interlace
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 33.75KHz
v: height 1080 start 1084 end 1094 total 1124 clock 60.05Hz
1920x1080 (0x1c6) 74.180MHz +HSync +VSync Interlace
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 33.72KHz
v: height 1080 start 1084 end 1094 total 1124 clock 60.00Hz
1680x1050 (0x1c7) 146.250MHz -HSync +VSync
h: width 1680 start 1784 end 1960 total 2240 skew 0 clock 65.29KHz
v: height 1050 start 1053 end 1059 total 1089 clock 59.95Hz
1600x900 (0x1c8) 108.000MHz +HSync +VSync
h: width 1600 start 1624 end 1704 total 1800 skew 0 clock 60.00KHz
v: height 900 start 901 end 904 total 1000 clock 60.00Hz
1440x900 (0x1c9) 106.500MHz -HSync +VSync
h: width 1440 start 1520 end 1672 total 1904 skew 0 clock 55.93KHz
v: height 900 start 903 end 909 total 934 clock 59.89Hz
1366x768 (0x1ca) 85.500MHz +HSync +VSync
h: width 1366 start 1436 end 1579 total 1792 skew 0 clock 47.71KHz
v: height 768 start 771 end 774 total 798 clock 59.79Hz
1280x1024 (0x1cb) 135.000MHz +HSync +VSync
h: width 1280 start 1296 end 1440 total 1688 skew 0 clock 79.98KHz
v: height 1024 start 1025 end 1028 total 1066 clock 75.02Hz
1280x1024 (0x1cc) 108.000MHz +HSync +VSync
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 63.98KHz
v: height 1024 start 1025 end 1028 total 1066 clock 60.02Hz
1280x800 (0x1cd) 83.500MHz -HSync +VSync
h: width 1280 start 1352 end 1480 total 1680 skew 0 clock 49.70KHz
v: height 800 start 803 end 809 total 831 clock 59.81Hz
1280x720 (0x1ce) 74.250MHz +HSync +VSync
h: width 1280 start 1390 end 1430 total 1650 skew 0 clock 45.00KHz
v: height 720 start 725 end 730 total 750 clock 60.00Hz
1280x720 (0x1cf) 74.180MHz +HSync +VSync
h: width 1280 start 1390 end 1430 total 1650 skew 0 clock 44.96KHz
v: height 720 start 725 end 730 total 750 clock 59.94Hz
1152x864 (0x1d0) 108.000MHz +HSync +VSync
h: width 1152 start 1216 end 1344 total 1600 skew 0 clock 67.50KHz
v: height 864 start 865 end 868 total 900 clock 75.00Hz
1024x768 (0x1d1) 78.750MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.02KHz
v: height 768 start 769 end 772 total 800 clock 75.03Hz
1024x768 (0x1d2) 75.000MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.48KHz
v: height 768 start 771 end 777 total 806 clock 70.07Hz
1024x768 (0x1d3) 65.000MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.36KHz
v: height 768 start 771 end 777 total 806 clock 60.00Hz
800x600 (0x1d4) 49.500MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock 46.88KHz
v: height 600 start 601 end 604 total 625 clock 75.00Hz
800x600 (0x1d5) 50.000MHz +HSync +VSync
h: width 800 start 856 end 976 total 1040 skew 0 clock 48.08KHz
v: height 600 start 637 end 643 total 666 clock 72.19Hz
800x600 (0x1d6) 40.000MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.88KHz
v: height 600 start 601 end 605 total 628 clock 60.32Hz
720x480 (0x1d7) 27.000MHz -HSync -VSync
h: width 720 start 736 end 798 total 858 skew 0 clock 31.47KHz
v: height 480 start 489 end 495 total 525 clock 59.94Hz
720x480 (0x1d8) 13.500MHz -HSync -VSync Interlace
h: width 720 start 739 end 801 total 858 skew 0 clock 15.73KHz
v: height 480 start 488 end 494 total 524 clock 60.05Hz
640x480 (0x1d9) 31.500MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock 37.50KHz
v: height 480 start 481 end 484 total 500 clock 75.00Hz
640x480 (0x1da) 31.500MHz -HSync -VSync
h: width 640 start 656 end 696 total 832 skew 0 clock 37.86KHz
v: height 480 start 481 end 484 total 520 clock 72.81Hz
640x480 (0x1db) 25.175MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.47KHz
v: height 480 start 490 end 492 total 525 clock 59.94Hz
DP-0 disconnected (normal left inverted right x axis y axis)
Identifier: 0x1dc
Timestamp: 8595
Subpixel: unknown
Clones:
CRTCs: 0 1 2 3
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BorderDimensions: 4
supported: 4
Border: 0 0 0 0
range: (0, 65535)
SignalFormat: DisplayPort
supported: DisplayPort
ConnectorType: DisplayPort
ConnectorNumber: 3
_ConnectorLocation: 3
DP-1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x1dd
Timestamp: 8595
Subpixel: unknown
Clones:
CRTCs: 0 1 2 3
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BorderDimensions: 4
supported: 4
Border: 0 0 0 0
range: (0, 65535)
SignalFormat: TMDS
supported: TMDS
ConnectorType: DisplayPort
ConnectorNumber: 3
_ConnectorLocation: 3
DVI-D-0 disconnected (normal left inverted right x axis y axis)
Identifier: 0x1de
Timestamp: 8595
Subpixel: unknown
Clones:
CRTCs: 0 1 2 3
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BorderDimensions: 4
supported: 4
Border: 0 0 0 0
range: (0, 65535)
SignalFormat: TMDS
supported: TMDS
ConnectorType: DVI-D
ConnectorNumber: 1
_ConnectorLocation: 1cat /var/log/Xorg.0.log
[ 8.601]
X.Org X Server 1.18.0
Release Date: 2015-11-09
[ 8.601] X Protocol Version 11, Revision 0
[ 8.601] Build Operating System: Linux 4.2.3-1-ARCH x86_64
[ 8.601] Current Operating System: Linux orion 4.2.5-1-ARCH #1 SMP PREEMPT Tue Oct 27 08:13:28 CET 2015 x86_64
[ 8.601] Kernel command line: root=/dev/vga/root rw initrd=/initramfs-linux.img
[ 8.601] Build Date: 18 November 2015 08:07:09AM
[ 8.601]
[ 8.601] Current version of pixman: 0.32.8
[ 8.601] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 8.601] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 8.601] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Dec 8 01:09:57 2015
[ 8.605] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 8.605] (==) No Layout section. Using the first Screen section.
[ 8.605] (==) No screen section available. Using defaults.
[ 8.605] (**) |-->Screen "Default Screen Section" (0)
[ 8.605] (**) | |-->Monitor "<default monitor>"
[ 8.606] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 8.606] (==) Automatically adding devices
[ 8.606] (==) Automatically enabling devices
[ 8.606] (==) Automatically adding GPU devices
[ 8.606] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 8.610] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 8.610] Entry deleted from font path.
[ 8.610] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 8.610] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 8.611] Entry deleted from font path.
[ 8.611] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 8.611] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Type1/
[ 8.611] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 8.611] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 8.611] (II) Loader magic: 0x819d40
[ 8.611] (II) Module ABI versions:
[ 8.611] X.Org ANSI C Emulation: 0.4
[ 8.611] X.Org Video Driver: 20.0
[ 8.611] X.Org XInput driver : 22.1
[ 8.611] X.Org Server Extension : 9.0
[ 8.611] (++) using VT number 1
[ 8.611] (--) controlling tty is VT number 1, auto-enabling KeepTty
[ 8.612] (II) systemd-logind: took control of session /org/freedesktop/login1/session/c1
[ 8.612] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 8.612] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 8 paused 0
[ 8.614] (--) PCI:*(0:1:0:0) 10de:13c2:3842:2978 rev 161, Mem @ 0xfd000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288
[ 8.614] (--) PCI: (0:9:0:0) 14f1:8880:0070:2a18 rev 4, Mem @ 0xfe200000/2097152
[ 8.614] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 8.614] (II) LoadModule: "glx"
[ 8.616] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 8.676] (II) Module glx: vendor="NVIDIA Corporation"
[ 8.676] compiled for 4.0.2, module version = 1.0.0
[ 8.676] Module class: X.Org Server Extension
[ 8.676] (II) NVIDIA GLX Module 358.16 Mon Nov 16 18:54:01 PST 2015
[ 8.677] (II) Applying OutputClass "nvidia" to /dev/dri/card0
[ 8.677] loading driver: nvidia
[ 8.677] (==) Matched nvidia as autoconfigured driver 0
[ 8.677] (==) Matched nouveau as autoconfigured driver 1
[ 8.677] (==) Matched nv as autoconfigured driver 2
[ 8.677] (==) Matched nouveau as autoconfigured driver 3
[ 8.677] (==) Matched nv as autoconfigured driver 4
[ 8.677] (==) Matched modesetting as autoconfigured driver 5
[ 8.677] (==) Matched fbdev as autoconfigured driver 6
[ 8.677] (==) Matched vesa as autoconfigured driver 7
[ 8.677] (==) Assigned the driver to the xf86ConfigLayout
[ 8.677] (II) LoadModule: "nvidia"
[ 8.678] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 8.684] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 8.684] compiled for 4.0.2, module version = 1.0.0
[ 8.684] Module class: X.Org Video Driver
[ 8.685] (II) LoadModule: "nouveau"
[ 8.685] (WW) Warning, couldn't open module nouveau
[ 8.685] (II) UnloadModule: "nouveau"
[ 8.685] (II) Unloading nouveau
[ 8.685] (EE) Failed to load module "nouveau" (module does not exist, 0)
[ 8.685] (II) LoadModule: "nv"
[ 8.685] (WW) Warning, couldn't open module nv
[ 8.685] (II) UnloadModule: "nv"
[ 8.685] (II) Unloading nv
[ 8.685] (EE) Failed to load module "nv" (module does not exist, 0)
[ 8.685] (II) LoadModule: "modesetting"
[ 8.686] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 8.686] (II) Module modesetting: vendor="X.Org Foundation"
[ 8.686] compiled for 1.18.0, module version = 1.18.0
[ 8.686] Module class: X.Org Video Driver
[ 8.686] ABI class: X.Org Video Driver, version 20.0
[ 8.686] (II) LoadModule: "fbdev"
[ 8.686] (WW) Warning, couldn't open module fbdev
[ 8.686] (II) UnloadModule: "fbdev"
[ 8.686] (II) Unloading fbdev
[ 8.686] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 8.686] (II) LoadModule: "vesa"
[ 8.687] (WW) Warning, couldn't open module vesa
[ 8.687] (II) UnloadModule: "vesa"
[ 8.687] (II) Unloading vesa
[ 8.687] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 8.687] (II) NVIDIA dlloader X Driver 358.16 Mon Nov 16 18:32:40 PST 2015
[ 8.687] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 8.687] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 8.688] (II) Loading sub module "fb"
[ 8.688] (II) LoadModule: "fb"
[ 8.688] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 8.689] (II) Module fb: vendor="X.Org Foundation"
[ 8.689] compiled for 1.18.0, module version = 1.0.0
[ 8.689] ABI class: X.Org ANSI C Emulation, version 0.4
[ 8.689] (II) Loading sub module "wfb"
[ 8.689] (II) LoadModule: "wfb"
[ 8.689] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 8.691] (II) Module wfb: vendor="X.Org Foundation"
[ 8.691] compiled for 1.18.0, module version = 1.0.0
[ 8.691] ABI class: X.Org ANSI C Emulation, version 0.4
[ 8.691] (II) Loading sub module "ramdac"
[ 8.691] (II) LoadModule: "ramdac"
[ 8.691] (II) Module "ramdac" already built-in
[ 8.693] (WW) Falling back to old probe method for modesetting
[ 8.693] (II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 8.693] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 8.693] (==) NVIDIA(0): RGB weight 888
[ 8.693] (==) NVIDIA(0): Default visual is TrueColor
[ 8.693] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 8.694] (**) NVIDIA(0): Enabling 2D acceleration
[ 9.363] (--) NVIDIA(0): Valid display device(s) on GPU-0 at PCI:1:0:0
[ 9.363] (--) NVIDIA(0): CRT-0
[ 9.363] (--) NVIDIA(0): DFP-0
[ 9.363] (--) NVIDIA(0): DFP-1 (boot)
[ 9.363] (--) NVIDIA(0): DFP-2
[ 9.363] (--) NVIDIA(0): DFP-3
[ 9.363] (--) NVIDIA(0): DFP-4
[ 9.365] (--) NVIDIA(0): CRT-0: disconnected
[ 9.365] (--) NVIDIA(0): CRT-0: 400.0 MHz maximum pixel clock
[ 9.365] (--) NVIDIA(0):
[ 9.368] (--) NVIDIA(0): DFP-0: disconnected
[ 9.368] (--) NVIDIA(0): DFP-0: Internal TMDS
[ 9.368] (--) NVIDIA(0): DFP-0: 330.0 MHz maximum pixel clock
[ 9.368] (--) NVIDIA(0):
[ 9.398] (--) NVIDIA(0): ONKYO Corporation TX-NR626 (DFP-1): connected
[ 9.398] (--) NVIDIA(0): ONKYO Corporation TX-NR626 (DFP-1): Internal TMDS
[ 9.398] (--) NVIDIA(0): ONKYO Corporation TX-NR626 (DFP-1): 600.0 MHz maximum pixel clock
[ 9.398] (--) NVIDIA(0):
[ 9.398] (--) NVIDIA(0): DFP-2: disconnected
[ 9.398] (--) NVIDIA(0): DFP-2: Internal DisplayPort
[ 9.398] (--) NVIDIA(0): DFP-2: 960.0 MHz maximum pixel clock
[ 9.398] (--) NVIDIA(0):
[ 9.398] (--) NVIDIA(0): DFP-3: disconnected
[ 9.399] (--) NVIDIA(0): DFP-3: Internal TMDS
[ 9.399] (--) NVIDIA(0): DFP-3: 330.0 MHz maximum pixel clock
[ 9.399] (--) NVIDIA(0):
[ 9.399] (--) NVIDIA(0): DFP-4: disconnected
[ 9.399] (--) NVIDIA(0): DFP-4: Internal TMDS
[ 9.399] (--) NVIDIA(0): DFP-4: 330.0 MHz maximum pixel clock
[ 9.399] (--) NVIDIA(0):
[ 9.399] (II) NVIDIA(GPU-0): Found DRM driver nvidia-drm (20150116)
[ 9.399] (II) NVIDIA(0): NVIDIA GPU GeForce GTX 970 (GM204-A) at PCI:1:0:0 (GPU-0)
[ 9.399] (--) NVIDIA(0): Memory: 4194304 kBytes
[ 9.399] (--) NVIDIA(0): VideoBIOS: 84.04.36.00.71
[ 9.399] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[ 9.399] (**) NVIDIA(0): Using HorizSync/VertRefresh ranges from the EDID for display
[ 9.399] (**) NVIDIA(0): device ONKYO Corporation TX-NR626 (DFP-1) (Using EDID
[ 9.400] (**) NVIDIA(0): frequencies has been enabled on all display devices.)
[ 9.402] (==) NVIDIA(0):
[ 9.402] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 9.402] (==) NVIDIA(0): will be used as the requested mode.
[ 9.402] (==) NVIDIA(0):
[ 9.403] (II) NVIDIA(0): Validated MetaModes:
[ 9.403] (II) NVIDIA(0): "DFP-1:nvidia-auto-select"
[ 9.403] (II) NVIDIA(0): Virtual screen size determined to be 1920 x 1080
[ 9.409] (--) NVIDIA(0): DPI set to (304, 304); computed from "UseEdidDpi" X config
[ 9.409] (--) NVIDIA(0): option
[ 9.409] (II) UnloadModule: "modesetting"
[ 9.409] (II) Unloading modesetting
[ 9.409] (--) Depth 24 pixmap format is 32 bpp
[ 9.410] (II) NVIDIA: Using 3072.00 MB of virtual memory for indirect memory
[ 9.410] (II) NVIDIA: access.
[ 9.413] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 9.413] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 9.413] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 9.413] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 9.413] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 9.413] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 9.413] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 9.413] (II) NVIDIA(0): Config Options in the README.
[ 9.444] (II) NVIDIA(0): Setting mode "DFP-1:nvidia-auto-select"
[ 9.483] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 9.483] (==) NVIDIA(0): Backing store enabled
[ 9.483] (==) NVIDIA(0): Silken mouse enabled
[ 9.484] (==) NVIDIA(0): DPMS enabled
[ 9.485] (II) Loading sub module "dri2"
[ 9.485] (II) LoadModule: "dri2"
[ 9.485] (II) Module "dri2" already built-in
[ 9.485] (II) NVIDIA(0): [DRI2] Setup complete
[ 9.485] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 9.485] (--) RandR disabled
[ 9.489] (II) Initializing extension GLX
[ 9.489] (II) Indirect GLX disabled.(II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 9.554] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 9.554] (II) LoadModule: "evdev"
[ 9.554] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 9.556] (II) Module evdev: vendor="X.Org Foundation"
[ 9.556] compiled for 1.18.0, module version = 2.10.0
[ 9.556] Module class: X.Org XInput Driver
[ 9.556] ABI class: X.Org XInput driver, version 22.1
[ 9.557] (II) systemd-logind: got fd for /dev/input/event3 13:67 fd 29 paused 0
[ 9.557] (II) Using input driver 'evdev' for 'Power Button'
[ 9.557] (**) Power Button: always reports core events
[ 9.557] (**) evdev: Power Button: Device: "/dev/input/event3"
[ 9.557] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 9.557] (--) evdev: Power Button: Found keys
[ 9.557] (II) evdev: Power Button: Configuring as keyboard
[ 9.557] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input5/event3"
[ 9.557] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 9.557] (**) Option "xkb_rules" "evdev"
[ 9.557] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 9.557] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 9.558] (II) systemd-logind: got fd for /dev/input/event2 13:66 fd 30 paused 0
[ 9.558] (II) Using input driver 'evdev' for 'Power Button'
[ 9.558] (**) Power Button: always reports core events
[ 9.558] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 9.558] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 9.558] (--) evdev: Power Button: Found keys
[ 9.558] (II) evdev: Power Button: Configuring as keyboard
[ 9.558] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4/event2"
[ 9.558] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 9.558] (**) Option "xkb_rules" "evdev"
[ 9.558] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event15)
[ 9.558] (II) No input driver specified, ignoring this device.
[ 9.558] (II) This device may have been added with another device file.
[ 9.558] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event16)
[ 9.558] (II) No input driver specified, ignoring this device.
[ 9.558] (II) This device may have been added with another device file.
[ 9.558] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event17)
[ 9.558] (II) No input driver specified, ignoring this device.
[ 9.558] (II) This device may have been added with another device file.
[ 9.559] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event18)
[ 9.559] (II) No input driver specified, ignoring this device.
[ 9.559] (II) This device may have been added with another device file.
[ 9.559] (II) config/udev: Adding input device Valve Software Steam Controller (/dev/input/event0)
[ 9.559] (**) Valve Software Steam Controller: Applying InputClass "evdev pointer catchall"
[ 9.559] (**) Valve Software Steam Controller: Applying InputClass "evdev keyboard catchall"
[ 9.559] (II) systemd-logind: got fd for /dev/input/event0 13:64 fd 31 paused 0
[ 9.559] (II) Using input driver 'evdev' for 'Valve Software Steam Controller'
[ 9.559] (**) Valve Software Steam Controller: always reports core events
[ 9.559] (**) evdev: Valve Software Steam Controller: Device: "/dev/input/event0"
[ 9.559] (--) evdev: Valve Software Steam Controller: Vendor 0x28de Product 0x1142
[ 9.559] (--) evdev: Valve Software Steam Controller: Found 9 mouse buttons
[ 9.559] (--) evdev: Valve Software Steam Controller: Found scroll wheel(s)
[ 9.559] (--) evdev: Valve Software Steam Controller: Found relative axes
[ 9.559] (--) evdev: Valve Software Steam Controller: Found x and y relative axes
[ 9.559] (--) evdev: Valve Software Steam Controller: Found keys
[ 9.559] (II) evdev: Valve Software Steam Controller: Configuring as mouse
[ 9.559] (II) evdev: Valve Software Steam Controller: Configuring as keyboard
[ 9.559] (II) evdev: Valve Software Steam Controller: Adding scrollwheel support
[ 9.559] (**) evdev: Valve Software Steam Controller: YAxisMapping: buttons 4 and 5
[ 9.559] (**) evdev: Valve Software Steam Controller: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 9.559] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:12.0/usb9/9-2/9-2:1.0/0003:28DE:1142.0002/input/input2/event0"
[ 9.559] (II) XINPUT: Adding extended input device "Valve Software Steam Controller" (type: KEYBOARD, id 8)
[ 9.560] (**) Option "xkb_rules" "evdev"
[ 9.560] (II) evdev: Valve Software Steam Controller: initialized for relative axes.
[ 9.560] (**) Valve Software Steam Controller: (accel) keeping acceleration scheme 1
[ 9.560] (**) Valve Software Steam Controller: (accel) acceleration profile 0
[ 9.560] (**) Valve Software Steam Controller: (accel) acceleration factor: 2.000
[ 9.560] (**) Valve Software Steam Controller: (accel) acceleration threshold: 4
[ 9.560] (II) config/udev: Adding input device Valve Software Steam Controller (/dev/input/mouse0)
[ 9.560] (II) No input driver specified, ignoring this device.
[ 9.560] (II) This device may have been added with another device file.
[ 9.560] (II) config/udev: Adding input device HD Pro Webcam C920 (/dev/input/event5)
[ 9.560] (**) HD Pro Webcam C920: Applying InputClass "evdev keyboard catchall"
[ 9.561] (II) systemd-logind: got fd for /dev/input/event5 13:69 fd 32 paused 0
[ 9.561] (II) Using input driver 'evdev' for 'HD Pro Webcam C920'
[ 9.561] (**) HD Pro Webcam C920: always reports core events
[ 9.561] (**) evdev: HD Pro Webcam C920: Device: "/dev/input/event5"
[ 9.561] (--) evdev: HD Pro Webcam C920: Vendor 0x46d Product 0x82d
[ 9.561] (--) evdev: HD Pro Webcam C920: Found keys
[ 9.561] (II) evdev: HD Pro Webcam C920: Configuring as keyboard
[ 9.561] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:13.2/usb4/4-2/4-2:1.0/input/input8/event5"
[ 9.561] (II) XINPUT: Adding extended input device "HD Pro Webcam C920" (type: KEYBOARD, id 9)
[ 9.561] (**) Option "xkb_rules" "evdev"
[ 9.561] (II) config/udev: Adding input device HDA ATI SB Rear Mic (/dev/input/event7)
[ 9.561] (II) No input driver specified, ignoring this device.
[ 9.561] (II) This device may have been added with another device file.
[ 9.561] (II) config/udev: Adding input device HDA ATI SB Line (/dev/input/event8)
[ 9.561] (II) No input driver specified, ignoring this device.
[ 9.561] (II) This device may have been added with another device file.
[ 9.562] (II) config/udev: Adding input device HDA ATI SB Line Out Front (/dev/input/event9)
[ 9.562] (II) No input driver specified, ignoring this device.
[ 9.562] (II) This device may have been added with another device file.
[ 9.562] (II) config/udev: Adding input device HDA ATI SB Line Out Surround (/dev/input/event10)
[ 9.562] (II) No input driver specified, ignoring this device.
[ 9.562] (II) This device may have been added with another device file.
[ 9.562] (II) config/udev: Adding input device HDA ATI SB Line Out CLFE (/dev/input/event11)
[ 9.562] (II) No input driver specified, ignoring this device.
[ 9.562] (II) This device may have been added with another device file.
[ 9.562] (II) config/udev: Adding input device HDA ATI SB Line Out Side (/dev/input/event12)
[ 9.562] (II) No input driver specified, ignoring this device.
[ 9.562] (II) This device may have been added with another device file.
[ 9.562] (II) config/udev: Adding input device HDA ATI SB Front Headphone (/dev/input/event13)
[ 9.562] (II) No input driver specified, ignoring this device.
[ 9.562] (II) This device may have been added with another device file.
[ 9.563] (II) config/udev: Adding input device HDA ATI SB Front Mic (/dev/input/event6)
[ 9.563] (II) No input driver specified, ignoring this device.
[ 9.563] (II) This device may have been added with another device file.
[ 9.563] (II) config/udev: Adding input device Logitech K400 (/dev/input/event1)
[ 9.563] (**) Logitech K400: Applying InputClass "evdev pointer catchall"
[ 9.563] (**) Logitech K400: Applying InputClass "evdev keyboard catchall"
[ 9.563] (II) systemd-logind: got fd for /dev/input/event1 13:65 fd 33 paused 0
[ 9.563] (II) Using input driver 'evdev' for 'Logitech K400'
[ 9.563] (**) Logitech K400: always reports core events
[ 9.563] (**) evdev: Logitech K400: Device: "/dev/input/event1"
[ 9.563] (--) evdev: Logitech K400: Vendor 0x46d Product 0x4024
[ 9.563] (--) evdev: Logitech K400: Found 20 mouse buttons
[ 9.563] (--) evdev: Logitech K400: Found scroll wheel(s)
[ 9.563] (--) evdev: Logitech K400: Found relative axes
[ 9.563] (--) evdev: Logitech K400: Found x and y relative axes
[ 9.563] (--) evdev: Logitech K400: Found absolute axes
[ 9.563] (II) evdev: Logitech K400: Forcing absolute x/y axes to exist.
[ 9.563] (--) evdev: Logitech K400: Found keys
[ 9.563] (II) evdev: Logitech K400: Configuring as mouse
[ 9.563] (II) evdev: Logitech K400: Configuring as keyboard
[ 9.563] (II) evdev: Logitech K400: Adding scrollwheel support
[ 9.563] (**) evdev: Logitech K400: YAxisMapping: buttons 4 and 5
[ 9.563] (**) evdev: Logitech K400: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 9.563] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:16.0/usb13/13-2/13-2:1.2/0003:046D:C52B.0009/0003:046D:4024.000A/input/input3/event1"
[ 9.563] (II) XINPUT: Adding extended input device "Logitech K400" (type: KEYBOARD, id 10)
[ 9.563] (**) Option "xkb_rules" "evdev"
[ 9.564] (II) evdev: Logitech K400: initialized for relative axes.
[ 9.564] (WW) evdev: Logitech K400: ignoring absolute axes.
[ 9.564] (**) Logitech K400: (accel) keeping acceleration scheme 1
[ 9.564] (**) Logitech K400: (accel) acceleration profile 0
[ 9.564] (**) Logitech K400: (accel) acceleration factor: 2.000
[ 9.564] (**) Logitech K400: (accel) acceleration threshold: 4
[ 9.564] (II) config/udev: Adding input device Logitech K400 (/dev/input/mouse1)
[ 9.564] (II) No input driver specified, ignoring this device.
[ 9.564] (II) This device may have been added with another device file.
[ 9.564] (II) config/udev: Adding input device Eee PC WMI hotkeys (/dev/input/event14)
[ 9.564] (**) Eee PC WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[ 9.565] (II) systemd-logind: got fd for /dev/input/event14 13:78 fd 34 paused 0
[ 9.565] (II) Using input driver 'evdev' for 'Eee PC WMI hotkeys'
[ 9.565] (**) Eee PC WMI hotkeys: always reports core events
[ 9.565] (**) evdev: Eee PC WMI hotkeys: Device: "/dev/input/event14"
[ 9.565] (--) evdev: Eee PC WMI hotkeys: Vendor 0 Product 0
[ 9.565] (--) evdev: Eee PC WMI hotkeys: Found keys
[ 9.565] (II) evdev: Eee PC WMI hotkeys: Configuring as keyboard
[ 9.565] (**) Option "config_info" "udev:/sys/devices/platform/eeepc-wmi/input/input17/event14"
[ 9.565] (II) XINPUT: Adding extended input device "Eee PC WMI hotkeys" (type: KEYBOARD, id 11)
[ 9.565] (**) Option "xkb_rules" "evdev"
[ 9.565] (II) config/udev: Adding input device PC Speaker (/dev/input/event4)
[ 9.565] (II) No input driver specified, ignoring this device.
[ 9.565] (II) This device may have been added with another device file.
[ 9.596] (--) NVIDIA(GPU-0): CRT-0: disconnected
[ 9.596] (--) NVIDIA(GPU-0): CRT-0: 400.0 MHz maximum pixel clock
[ 9.596] (--) NVIDIA(GPU-0):
[ 9.599] (--) NVIDIA(GPU-0): DFP-0: disconnected
[ 9.599] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[ 9.599] (--) NVIDIA(GPU-0): DFP-0: 330.0 MHz maximum pixel clock
[ 9.599] (--) NVIDIA(GPU-0):
[ 9.629] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): connected
[ 9.629] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): Internal TMDS
[ 9.629] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): 600.0 MHz maximum pixel clock
[ 9.629] (--) NVIDIA(GPU-0):
[ 9.629] (--) NVIDIA(GPU-0): DFP-2: disconnected
[ 9.629] (--) NVIDIA(GPU-0): DFP-2: Internal DisplayPort
[ 9.629] (--) NVIDIA(GPU-0): DFP-2: 960.0 MHz maximum pixel clock
[ 9.629] (--) NVIDIA(GPU-0):
[ 9.629] (--) NVIDIA(GPU-0): DFP-3: disconnected
[ 9.629] (--) NVIDIA(GPU-0): DFP-3: Internal TMDS
[ 9.629] (--) NVIDIA(GPU-0): DFP-3: 330.0 MHz maximum pixel clock
[ 9.629] (--) NVIDIA(GPU-0):
[ 9.629] (--) NVIDIA(GPU-0): DFP-4: disconnected
[ 9.629] (--) NVIDIA(GPU-0): DFP-4: Internal TMDS
[ 9.629] (--) NVIDIA(GPU-0): DFP-4: 330.0 MHz maximum pixel clock
[ 9.629] (--) NVIDIA(GPU-0):
[ 15.779] (--) NVIDIA(GPU-0): CRT-0: disconnected
[ 15.779] (--) NVIDIA(GPU-0): CRT-0: 400.0 MHz maximum pixel clock
[ 15.779] (--) NVIDIA(GPU-0):
[ 15.782] (--) NVIDIA(GPU-0): DFP-0: disconnected
[ 15.782] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[ 15.782] (--) NVIDIA(GPU-0): DFP-0: 330.0 MHz maximum pixel clock
[ 15.782] (--) NVIDIA(GPU-0):
[ 15.812] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): connected
[ 15.812] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): Internal TMDS
[ 15.812] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): 600.0 MHz maximum pixel clock
[ 15.812] (--) NVIDIA(GPU-0):
[ 15.813] (--) NVIDIA(GPU-0): DFP-2: disconnected
[ 15.813] (--) NVIDIA(GPU-0): DFP-2: Internal DisplayPort
[ 15.813] (--) NVIDIA(GPU-0): DFP-2: 960.0 MHz maximum pixel clock
[ 15.813] (--) NVIDIA(GPU-0):
[ 15.813] (--) NVIDIA(GPU-0): DFP-3: disconnected
[ 15.813] (--) NVIDIA(GPU-0): DFP-3: Internal TMDS
[ 15.813] (--) NVIDIA(GPU-0): DFP-3: 330.0 MHz maximum pixel clock
[ 15.813] (--) NVIDIA(GPU-0):
[ 15.813] (--) NVIDIA(GPU-0): DFP-4: disconnected
[ 15.813] (--) NVIDIA(GPU-0): DFP-4: Internal TMDS
[ 15.813] (--) NVIDIA(GPU-0): DFP-4: 330.0 MHz maximum pixel clock
[ 15.813] (--) NVIDIA(GPU-0):
[ 28.177] (--) NVIDIA(GPU-0): CRT-0: disconnected
[ 28.177] (--) NVIDIA(GPU-0): CRT-0: 400.0 MHz maximum pixel clock
[ 28.177] (--) NVIDIA(GPU-0):
[ 28.180] (--) NVIDIA(GPU-0): DFP-0: disconnected
[ 28.180] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[ 28.180] (--) NVIDIA(GPU-0): DFP-0: 330.0 MHz maximum pixel clock
[ 28.180] (--) NVIDIA(GPU-0):
[ 28.211] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): connected
[ 28.211] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): Internal TMDS
[ 28.211] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): 600.0 MHz maximum pixel clock
[ 28.211] (--) NVIDIA(GPU-0):
[ 28.211] (--) NVIDIA(GPU-0): DFP-2: disconnected
[ 28.211] (--) NVIDIA(GPU-0): DFP-2: Internal DisplayPort
[ 28.211] (--) NVIDIA(GPU-0): DFP-2: 960.0 MHz maximum pixel clock
[ 28.211] (--) NVIDIA(GPU-0):
[ 28.211] (--) NVIDIA(GPU-0): DFP-3: disconnected
[ 28.211] (--) NVIDIA(GPU-0): DFP-3: Internal TMDS
[ 28.211] (--) NVIDIA(GPU-0): DFP-3: 330.0 MHz maximum pixel clock
[ 28.211] (--) NVIDIA(GPU-0):
[ 28.211] (--) NVIDIA(GPU-0): DFP-4: disconnected
[ 28.211] (--) NVIDIA(GPU-0): DFP-4: Internal TMDS
[ 28.211] (--) NVIDIA(GPU-0): DFP-4: 330.0 MHz maximum pixel clock
[ 28.211] (--) NVIDIA(GPU-0):
[ 28.569] (--) NVIDIA(GPU-0): CRT-0: disconnected
[ 28.569] (--) NVIDIA(GPU-0): CRT-0: 400.0 MHz maximum pixel clock
[ 28.569] (--) NVIDIA(GPU-0):
[ 28.572] (--) NVIDIA(GPU-0): DFP-0: disconnected
[ 28.572] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[ 28.572] (--) NVIDIA(GPU-0): DFP-0: 330.0 MHz maximum pixel clock
[ 28.572] (--) NVIDIA(GPU-0):
[ 28.602] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): connected
[ 28.602] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): Internal TMDS
[ 28.602] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): 600.0 MHz maximum pixel clock
[ 28.602] (--) NVIDIA(GPU-0):
[ 28.602] (--) NVIDIA(GPU-0): DFP-2: disconnected
[ 28.602] (--) NVIDIA(GPU-0): DFP-2: Internal DisplayPort
[ 28.602] (--) NVIDIA(GPU-0): DFP-2: 960.0 MHz maximum pixel clock
[ 28.602] (--) NVIDIA(GPU-0):
[ 28.602] (--) NVIDIA(GPU-0): DFP-3: disconnected
[ 28.602] (--) NVIDIA(GPU-0): DFP-3: Internal TMDS
[ 28.602] (--) NVIDIA(GPU-0): DFP-3: 330.0 MHz maximum pixel clock
[ 28.602] (--) NVIDIA(GPU-0):
[ 28.602] (--) NVIDIA(GPU-0): DFP-4: disconnected
[ 28.602] (--) NVIDIA(GPU-0): DFP-4: Internal TMDS
[ 28.602] (--) NVIDIA(GPU-0): DFP-4: 330.0 MHz maximum pixel clock
[ 28.602] (--) NVIDIA(GPU-0):
[ 74.663] (II) config/udev: Adding input device Microsoft X-Box 360 pad (/dev/input/js0)
[ 74.663] (II) No input driver specified, ignoring this device.
[ 74.663] (II) This device may have been added with another device file.
[ 74.690] (II) config/udev: Adding input device Microsoft X-Box 360 pad (/dev/input/event19)
[ 74.690] (II) No input driver specified, ignoring this device.
[ 74.690] (II) This device may have been added with another device file.
[ 142.080] (--) NVIDIA(GPU-0): CRT-0: disconnected
[ 142.080] (--) NVIDIA(GPU-0): CRT-0: 400.0 MHz maximum pixel clock
[ 142.080] (--) NVIDIA(GPU-0):
[ 142.083] (--) NVIDIA(GPU-0): DFP-0: disconnected
[ 142.083] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[ 142.083] (--) NVIDIA(GPU-0): DFP-0: 330.0 MHz maximum pixel clock
[ 142.083] (--) NVIDIA(GPU-0):
[ 142.117] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): connected
[ 142.118] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): Internal TMDS
[ 142.118] (--) NVIDIA(GPU-0): ONKYO Corporation TX-NR626 (DFP-1): 600.0 MHz maximum pixel clock
[ 142.118] (--) NVIDIA(GPU-0):
[ 142.118] (--) NVIDIA(GPU-0): DFP-2: disconnected
[ 142.118] (--) NVIDIA(GPU-0): DFP-2: Internal DisplayPort
[ 142.118] (--) NVIDIA(GPU-0): DFP-2: 960.0 MHz maximum pixel clock
[ 142.118] (--) NVIDIA(GPU-0):
[ 142.118] (--) NVIDIA(GPU-0): DFP-3: disconnected
[ 142.118] (--) NVIDIA(GPU-0): DFP-3: Internal TMDS
[ 142.118] (--) NVIDIA(GPU-0): DFP-3: 330.0 MHz maximum pixel clock
[ 142.118] (--) NVIDIA(GPU-0):
[ 142.118] (--) NVIDIA(GPU-0): DFP-4: disconnected
[ 142.118] (--) NVIDIA(GPU-0): DFP-4: Internal TMDS
[ 142.118] (--) NVIDIA(GPU-0): DFP-4: 330.0 MHz maximum pixel clock
[ 142.118] (--) NVIDIA(GPU-0): lspci-v
...
01:00.0 VGA compatible controller: NVIDIA Corporation GM204 [GeForce GTX 970] (rev a1) (prog-if 00 [VGA controller])
Subsystem: eVga.com. Corp. Device 2978
Flags: bus master, fast devsel, latency 0, IRQ 63
Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
Memory at d0000000 (64-bit, prefetchable) [size=32M]
I/O ports at e000 [size=128]
[virtual] Expansion ROM at fe000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Legacy Endpoint, MSI 00
Capabilities: [100] Virtual Channel
Capabilities: [250] Latency Tolerance Reporting
Capabilities: [258] L1 PM Substates
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel driver in use: nvidia
Kernel modules: nouveau, nvidia
...Last edited by cprussin (2015-12-08 09:45:00)
Offline
#3 2015-12-09 17:04:11
- cprussin
- Member
- Registered: 2010-07-20
- Posts: 9
Re: nvidia output off center
Thanks for the reply, but I don't think that this issue is related to mine. This issue appears to be that the driver is running weird resolutions over VGA specifically. My issue is not a resolution issue but a pixel mapping issue, and is not happening over VGA but rather over HDMI (also happens on my display port). It appears that the nvidia driver is not mapping pixels correctly for my receiver, but I don't know these technologies well enough to even know if that makes sense.
What's super odd about this is that the nvidia-304xx drivers worked just fine when I was using a card that supported them. While the nvidia drivers should have worked for that card, with the nvidia drivers I get the same weird offset. So it seems like something broke between the 304xx branch and the stable branch, but I'd like to be a little more certain this isn't a configuration issue before I go submit a bug report.
Offline
#4 2016-01-28 23:08:04
- Algor88
- Member
- Registered: 2013-04-20
- Posts: 16
Re: nvidia output off center
Hi,
Have you found a solution? I think i have the same Problem with Nvidia GTX960->AVR (Onkyo Tx-SR608)->Tv (LG 42Lw570S). Some black Pixel on the Right side and missing Pixel on the left side. Top and Bottom are ok. I don't have that issue with my Laptop with gt330m and 340 driver.
I haven't seen your post so i created a new one:
https://bbs.archlinux.org/viewtopic.php?id=208171
The best Solution i have so far is activating Overscan on Tv and using Underscan/changing ViewPortOut. That gives me at least only a few Pixel missing on the Bottom.
Offline
#5 2016-01-29 02:37:30
- cprussin
- Member
- Registered: 2010-07-20
- Posts: 9
Re: nvidia output off center
When I went back and looked at this, I believe FernandoBasso was right about the issues being related (I meant to post a follow-up but I must have forgotten). It appears a bug was introduced in a recent version of the nvidia driver, and unfortunately, the main Linux driver contact at nvidia seems to be out on paternity leave.
I was able to get this issue fixed by downgrading my nvidia drivers. Unfortunately I can't give you the specific version information, since I have since switched to nouveau on my Arch build and Windows for gaming (gotta have that GTA V). However, I can tell you that it was a huge pain in the ass--a number of packages had to be downgraded to very specific versions, and it took me a few hours of just downgrading packages and restarting X before I finally found a combination that solved the issue.
If it helps, it appears the bug was introduced around v 355.11 of the nvidia drivers.
EDIT: I just went and read your post, and one thing I will say is that if you are facing the same issue as me, it is NOT an overscan issue and working with modelines/overscan settings is a waste of time that will not fix the issue. The driver version itself is bad and you need to downgrade to a version before the bug was introduced.
Last edited by cprussin (2016-01-29 02:38:47)
Offline
#6 2016-01-29 22:39:32
- Algor88
- Member
- Registered: 2013-04-20
- Posts: 16
Re: nvidia output off center
Yeah it is that bug. You might be intrested in the nvidia-352 package in aur if you want to switch back from nouveau.
Offline
Pages: 1