AC Charger not detected --- Compaq Presario CQ62

toucan · 2016-01-24 09:03:47

For about two seconds after the AC adapter is plugged in, running

 acpi -v

says that the adapter is on-line. After that period, the same command reports that the adapter is off-line.

The laptop will not charge while acpi says that the adapter is off-line; however, if left powered off and plugged in, the laptop will charge to its usual capacity.

The laptop has been fully functional running Arch for a number of years. I have tried both downgrading the kernel and adding the parameter acpi_osi=Linux to no avail.

 
$ dmesg | grep -i ACPI 
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=a2d7cf42-0d40-416c-856b-8d4c9cadda98 rw quiet acpi_osi=Linux
[    0.000000] BIOS-e820: [mem 0x00000000b9f82000-0x00000000b9fbefff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000b9fe0000-0x00000000b9ff6fff] ACPI data
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000FE020 000024 (v02 HPQOEM)
[    0.000000] ACPI: XSDT 0x00000000B9FF6120 00006C (v01 HPQOEM SLIC-MPC 00000001      01000013)
[    0.000000] ACPI: FACP 0x00000000B9FF5000 0000F4 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: DSDT 0x00000000B9FE4000 00CB5C (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: FACS 0x00000000B9F8F000 000040
[    0.000000] ACPI: HPET 0x00000000B9FF4000 000038 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: APIC 0x00000000B9FF3000 00006C (v02 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: MCFG 0x00000000B9FF2000 00003C (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: ASF! 0x00000000B9FF1000 0000A5 (v32 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: SLIC 0x00000000B9FE3000 000176 (v01 HPQOEM SLIC-MPC 06040000  LTP 00000001)
[    0.000000] ACPI: BOOT 0x00000000B9FE2000 000028 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: SSDT 0x00000000B9FE1000 0005B3 (v01 PmRef  Cpu0Cst  00003001 INTL 20060317)
[    0.000000] ACPI: SSDT 0x00000000B9FE0000 000655 (v01 PmRef  CpuPm    00003000 INTL 20060317)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=a2d7cf42-0d40-416c-856b-8d4c9cadda98 rw quiet acpi_osi=Linux
[    0.003368] ACPI: Core revision 20140724
[    0.017946] ACPI: All ACPI Tables successfully acquired
[    0.091071] PM: Registering ACPI NVS region [mem 0xb9f82000-0xb9fbefff] (249856 bytes)
[    0.092634] ACPI: bus type PCI registered
[    0.092636] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.107102] ACPI: Added _OSI(Module Device)
[    0.107105] ACPI: Added _OSI(Processor Device)
[    0.107106] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.107108] ACPI: Added _OSI(Processor Aggregator Device)
[    0.107110] ACPI: Added _OSI(Linux)
[    0.109783] ACPI: Executed 1 blocks of module-level executable AML code
[    0.110896] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query honored via cmdline
[    0.110911] ACPI Error: No handler for Region [ERAM] (ffff88013b028750) [EmbeddedControl] (20140724/evregion-163)
[    0.110916] ACPI Error: Region EmbeddedControl (ID=3) has no handler (20140724/exfldio-299)
[    0.110920] ACPI Error: Method parse/execution failed [\_SB_.PCI0._INI] (Node ffff88013b0319d8), AE_NOT_EXIST (20140724/psparse-536)
[    0.111461] ACPI: Interpreter enabled
[    0.111461] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140724/hwxface-580)
[    0.111461] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140724/hwxface-580)
[    0.111461] ACPI: (supports S0 S3 S4 S5)
[    0.111461] ACPI: Using IOAPIC for interrupt routing

[    0.111461] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.120356] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.120365] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.120470] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug]
[    0.120565] acpi PNP0A08:00: _OSC: OS now controls [PME AER PCIeCapability]
[    0.121091] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.121811] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.122029] pci 0000:00:1a.1: System wakeup disabled by ACPI
[    0.143429] pci 0000:00:1a.7: System wakeup disabled by ACPI
[    0.143967] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.144192] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.166760] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.166898] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.173696] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.180246] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[    0.180310] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[    0.180372] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[    0.180433] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[    0.180495] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12)
[    0.180556] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12)
[    0.180617] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
[    0.180678] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[    0.181220] ACPI: Enabled 7 GPEs in block 00 to 3F
[    0.181277] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.181471] PCI: Using ACPI for IRQ routing
[    0.190195] pnp: PnP ACPI init
[    0.190321] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.190913] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.190957] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.191030] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.191078] pnp 00:04: Plug and Play ACPI device, IDs SYN1e2f SYN1e00 SYN0002 PNP0f13 (active)
[    0.191220] pnp: PnP ACPI: found 5 devices
[    0.499549] ACPI: bus type USB registered
[    8.999033] ACPI: acpi_idle registered with cpuidle
[    9.261659] ACPI: AC Adapter [ACAD] (off-line)
[    9.275870] ACPI: Power Button [PWRB]
[    9.347437] ACPI: Battery Slot [BAT0] (battery present)
[    9.347907] ACPI: Lid Switch [LID0]
[    9.348000] ACPI: Power Button [PWRF]
[    9.515392] ACPI: Thermal Zone [TZ01] (43 C)
[    9.829366] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042f conflicts with OpRegion 0x0000000000000400-0x000000000000047f (\PMBA) (20140724/utaddress-258)
[    9.829375] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    9.829379] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x000000000000050f (\GPIO) (20140724/utaddress-258)
[    9.829383] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.803589] ACPI: Video Device [OVGA] (multi-head: yes  rom: no  post: no)
[   11.804104] ACPI Error: [_T_0] Namespace lookup failure, AE_ALREADY_EXISTS (20140724/dswload2-330)
[   11.804114] ACPI Error: Method parse/execution failed [\_SB_.PCI0.OVGA.DD03.GBQC] (Node ffff88013b032320), AE_ALREADY_EXISTS (20140724/psparse-536)
[   11.804121] ACPI Error: Method parse/execution failed [\_SB_.PCI0.OVGA.DD03._BQC] (Node ffff88013b0322f8), AE_ALREADY_EXISTS (20140724/psparse-536)
[   11.804126] ACPI: Marking method _BQC as Serialized because of AE_ALREADY_EXISTS error
[   11.804130] ACPI Warning: Evaluating _BQC failed (20140724/video-846)
[   11.806064] acpi device:02: registered as cooling_device1

ewaller · 2016-01-24 17:31:30

I hate to ask, but does this laptop still have the ability to run one of those "operating systems" from the US Pacific Northwest that came with your system?
Have you seen if it can play nicely with your charger?

What is the state of your battery? Is it getting old, or is it in pretty good shape?

Last edited by ewaller (2016-01-24 17:31:46)

toucan · 2016-01-31 04:30:27

No alternate operating systems.

I think that the battery is not super young (~4 yrs old), but it still holds about 80% charge.

Arch Linux

#1 2016-01-24 09:03:47

AC Charger not detected --- Compaq Presario CQ62

#2 2016-01-24 17:31:30

Re: AC Charger not detected --- Compaq Presario CQ62

#3 2016-01-31 04:30:27

Re: AC Charger not detected --- Compaq Presario CQ62

Board footer