external hard drive randomly disconnects

thd93 · 2017-01-07 00:49:03

Hello,
My 4TB ext4 external hard drive randomly disconnects and remounts as read-only. Any ideas?

[313891.683509] scsi 7:0:0:0: Direct-Access     Seagate  BUP BK           0304 PQ: 0 ANSI: 6
[313891.727014] sd 7:0:0:0: [sdc] 7814037167 512-byte logical blocks: (4.00 TB/3.64 TiB)
[313891.727018] sd 7:0:0:0: [sdc] 4096-byte physical blocks
[313891.792675] sd 7:0:0:0: [sdc] Write Protect is off
[313891.792685] sd 7:0:0:0: [sdc] Mode Sense: 4f 00 00 00
[313891.793418] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[313891.958920]  sdc: sdc1
[313891.961891] sd 7:0:0:0: [sdc] Attached SCSI disk
[316293.063487] Aborting journal on device dm-1-8.
[316293.063530] Buffer I/O error on dev dm-1, logical block 488144896, lost sync page write
[316293.063543] JBD2: Error -5 detected when updating journal superblock for dm-1-8.
[318521.899135] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[318521.899177] EXT4-fs error (device dm-1): ext4_journal_check_start:56: Detected aborted journal
[318521.899190] EXT4-fs (dm-1): Remounting filesystem read-only
[318521.899201] EXT4-fs (dm-1): previous I/O error to superblock detected
[318521.899255] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[318551.853449] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #66584585: lblock 0: comm ranger: error -5 reading directory block
[318552.562096] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #62914561: lblock 0: comm ranger: error -5 reading directory block
[318553.145792] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #66846721: lblock 0: comm ranger: error -5 reading directory block
[318553.146921] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #62390273: lblock 0: comm ranger: error -5 reading directory block
[318553.745061] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #67633153: lblock 0: comm ranger: error -5 reading directory block
[318553.745497] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #66977793: lblock 0: comm ranger: error -5 reading directory block
[318553.746274] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #61865995: lblock 0: comm ranger: error -5 reading directory block
[318555.437637] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #68288513: lblock 0: comm ranger: error -5 reading directory block
[318555.438276] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #68157441: lblock 0: comm ranger: error -5 reading directory block
[318555.439291] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #61865985: lblock 0: comm ranger: error -5 reading directory block
[318577.974814] EXT4-fs (dm-1): previous I/O error to superblock detected
[318577.974852] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[318577.974858] EXT4-fs error (device dm-1): ext4_put_super:837: Couldn't clean up the journal
[318598.968517] usb 2-1.2: USB disconnect, device number 6
[318598.969422] sd 7:0:0:0: [sdc] Synchronizing SCSI cache
[318599.171132] sd 7:0:0:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x07 driverbyte=0x00
[318601.734599] usb 2-1.2: new high-speed USB device number 7 using ehci-pci
[318601.890782] scsi host6: uas
[318601.893088] scsi 6:0:0:0: Direct-Access     Seagate  BUP BK           0304 PQ: 0 ANSI: 6
[318601.939201] sd 6:0:0:0: [sdb] Spinning up disk...
[318602.954666] .....ready
[318607.008781] sd 6:0:0:0: [sdb] 7814037167 512-byte logical blocks: (4.00 TB/3.64 TiB)
[318607.008786] sd 6:0:0:0: [sdb] 2048-byte physical blocks
[318607.042153] sd 6:0:0:0: [sdb] Write Protect is off
[318607.042160] sd 6:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[318607.042891] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[318607.218483]  sdb: sdb1
[318607.222540] sd 6:0:0:0: [sdb] Attached SCSI disk
[318631.234528] device-mapper: table: 254:1: adding target device sdb1 caused an alignment inconsistency: physical_block_size=4096, logical_block_size=512, alignment_offset=0, start=33553920
[318631.234532] device-mapper: table: 254:1: adding target device sdb1 caused an alignment inconsistency: physical_block_size=4096, logical_block_size=512, alignment_offset=0, start=33553920
[318641.841636] EXT4-fs (dm-1): recovery complete
[318641.858727] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)

Last edited by thd93 (2017-01-07 00:53:06)

R00KIE · 2017-01-07 01:09:30

Don't cherry pick messages out of the dmesg output, post the full output.

thd93 · 2017-01-07 01:24:45

[    0.973392] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.979008] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    0.979196] hub 2-0:1.0: USB hub found
[    0.979205] hub 2-0:1.0: 3 ports detected
[    0.979384] ahci 0000:00:1f.2: version 3.0
[    0.979549] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    0.989646] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x1b impl SATA mode
[    0.989647] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pio slum part ems sxs apst 
[    1.012374] firewire_ohci 0000:0d:00.3: added OHCI v1.10 device as card 0, 4 IR + 4 IT contexts, quirks 0x11
[    1.021436] scsi host0: ahci
[    1.021742] scsi host1: ahci
[    1.022030] scsi host2: ahci
[    1.022307] scsi host3: ahci
[    1.022620] scsi host4: ahci
[    1.022800] scsi host5: ahci
[    1.022867] ata1: SATA max UDMA/133 abar m2048@0xf2528000 port 0xf2528100 irq 24
[    1.022870] ata2: SATA max UDMA/133 abar m2048@0xf2528000 port 0xf2528180 irq 24
[    1.022871] ata3: DUMMY
[    1.022873] ata4: SATA max UDMA/133 abar m2048@0xf2528000 port 0xf2528280 irq 24
[    1.022875] ata5: SATA max UDMA/133 abar m2048@0xf2528000 port 0xf2528300 irq 24
[    1.022876] ata6: DUMMY
[    1.282356] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.299026] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.335321] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.337329] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[    1.337333] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[    1.337336] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[    1.339597] ata1.00: ATA-8: WDC WD5000BEVT-22A0RT0, 01.01A01, max UDMA/133
[    1.339601] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.341627] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[    1.341631] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[    1.341634] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[    1.343670] ata1.00: configured for UDMA/133
[    1.343995] scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000BEVT-2 1A01 PQ: 0 ANSI: 5
[    1.419732] hub 1-1:1.0: USB hub found
[    1.419898] hub 1-1:1.0: 6 ports detected
[    1.436256] hub 2-1:1.0: USB hub found
[    1.436347] hub 2-1:1.0: 8 ports detected
[    1.525748] firewire_core 0000:0d:00.3: created device fw0: GUID 0021cc20090a9d31, S400
[    1.699054] usb 1-1.3: new full-speed USB device number 3 using ehci-pci
[    1.712024] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.714551] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[    1.714883] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[    1.714886] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[    1.715723] usb 2-1.2: new high-speed USB device number 3 using ehci-pci
[    1.716551] ata2.00: ATAPI: Optiarc DVD RW AD-7710H, 1.S0, max UDMA/100
[    1.719257] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[    1.719589] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[    1.719592] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[    1.721255] ata2.00: configured for UDMA/100
[    1.724360] scsi 1:0:0:0: CD-ROM            Optiarc  DVD RW AD-7710H  1.S0 PQ: 0 ANSI: 5
[    1.765729] tsc: Refined TSC clocksource calibration: 2491.905 MHz
[    1.765744] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x23eb5abbd7b, max_idle_ns: 440795277677 ns
[    1.869077] usb 1-1.4: new full-speed USB device number 4 using ehci-pci
[    1.878039] usbcore: registered new interface driver usb-storage
[    1.879497] scsi host6: uas
[    1.879696] usbcore: registered new interface driver uas
[    1.881019] scsi 6:0:0:0: Direct-Access     Seagate  BUP BK           0304 PQ: 0 ANSI: 6
[    1.881115] random: fast init done
[    2.048687] ata4: SATA link down (SStatus 0 SControl 300)
[    2.049075] usb 1-1.6: new high-speed USB device number 5 using ehci-pci
[    2.362014] ata5: SATA link down (SStatus 0 SControl 300)
[    2.366513] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    2.366693] sd 0:0:0:0: [sda] Write Protect is off
[    2.366702] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.366769] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.367188] sd 6:0:0:0: [sdb] 7814037167 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    2.367195] sd 6:0:0:0: [sdb] 4096-byte physical blocks
[    2.381037] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.381038] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.381189] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.400786]  sda: sda1 sda2 sda3
[    2.401005] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.779242] clocksource: Switched to clocksource tsc
[    4.140293] sd 6:0:0:0: [sdb] Write Protect is off
[    4.140301] sd 6:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[    4.141025] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.316349]  sdb: sdb1
[    4.319535] sd 6:0:0:0: [sdb] Attached SCSI disk
[    4.723192] device-mapper: uevent: version 1.0.3
[    4.723277] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[    7.326258] random: crng init done
[    9.678415] NET: Registered protocol family 38
[   10.497875] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[   12.168430] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.305745] systemd[1]: systemd 232 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[   12.306062] systemd[1]: Detected architecture x86-64.
[   12.331718] systemd[1]: Set hostname to <thinkpad>.
[   14.010544] systemd[1]: Listening on udev Control Socket.
[   14.010602] systemd[1]: Listening on Journal Socket (/dev/log).
[   14.015281] systemd[1]: Listening on Process Core Dump Socket.
[   14.015387] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   14.015648] systemd[1]: Created slice System Slice.
[   14.029964] systemd[1]: Mounting Debug File System...
[   14.030221] systemd[1]: Created slice system-getty.slice.
[   14.358069] EXT4-fs (dm-0): re-mounted. Opts: data=ordered
[   14.770011] tun: Universal TUN/TAP device driver, 1.6
[   14.770013] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   15.817759] systemd-journald[234]: Received request to flush runtime journal from PID 1
[   18.300234] tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
[   18.393560] tpm tpm0: TPM is disabled/deactivated (0x6)
[   18.587222] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\_SB.PCI0.LPC.PMIO) (20160422/utaddress-255)
[   18.587229] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   18.587233] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPC.LPIO) (20160422/utaddress-255)
[   18.587237] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   18.587239] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPC.LPIO) (20160422/utaddress-255)
[   18.587242] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   18.587243] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB.PCI0.LPC.LPIO) (20160422/utaddress-255)
[   18.587247] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   18.587248] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   18.767970] FUJITSU Extended Socket Network Device Driver - version 1.1 - Copyright (c) 2015 FUJITSU LIMITED
[   18.787422] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[   18.789031] ACPI: Lid Switch [LID]
[   18.789105] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[   18.789108] ACPI: Sleep Button [SLPB]
[   18.789176] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[   18.789178] ACPI: Power Button [PWRF]
[   18.794762] ACPI: Battery Slot [BAT0] (battery present)
[   18.809720] pps_core: LinuxPPS API ver. 1 registered
[   18.809721] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[   18.814672] PTP clock support registered
[   18.829130] thermal LNXTHERM:00: registered as thermal_zone0
[   18.829131] ACPI: Thermal Zone [THM0] (50 C)
[   18.855483] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   18.861244] [drm] Initialized drm 1.1.0 20060810
[   18.991080] ACPI: AC Adapter [AC] (on-line)
[   19.024153] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[   19.112108] wmi: Mapper loaded
[   19.165185] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[   19.165187] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[   19.165323] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[   19.215213] input: PC Speaker as /devices/platform/pcspkr/input/input5
[   19.224004] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[   19.224006] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[   19.224007] RAPL PMU: hw unit of domain package 2^-16 Joules
[   19.224008] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[   19.267912] e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock
[   19.370142] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:21:cc:b5:d8:b4
[   19.370154] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[   19.370192] e1000e 0000:00:19.0 eth0: MAC: 10, PHY: 11, PBA No: 1000FF-0FF
[   19.371066] [drm] Memory usable by graphics device = 2048M
[   19.371072] checking generic (e0000000 300000) vs hw (e0000000 10000000)
[   19.371075] fb: switching to inteldrmfb from VESA VGA
[   19.371139] Console: switching to colour dummy device 80x25
[   19.371350] [drm] Replacing VGA console driver
[   19.376900] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   19.376903] [drm] Driver supports precise vblank timestamp query.
[   19.377698] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   19.421538] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[   19.422860] acpi device:00: registered as cooling_device4
[   19.422957] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[   19.423007] [drm] Initialized i915 1.6.0 20160711 for 0000:00:02.0 on minor 0
[   19.463578] Intel(R) Wireless WiFi driver for Linux
[   19.463580] Copyright(c) 2003- 2015 Intel Corporation
[   19.463779] iwlwifi 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[   19.485324] Non-volatile memory driver v1.3
[   19.702045] fbcon: inteldrmfb (fb0) is primary device
[   19.757850] thinkpad_acpi: ThinkPad ACPI Extras v0.25
[   19.757850] thinkpad_acpi: http://ibm-acpi.sf.net/
[   19.757851] thinkpad_acpi: ThinkPad BIOS 83ET69WW (1.39 ), EC unknown
[   19.757851] thinkpad_acpi: Lenovo ThinkPad T420, model 41786UU
[   19.758247] thinkpad_acpi: radio switch found; radios are enabled
[   19.758259] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
[   19.758259] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
[   19.759398] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[   19.759751] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
[   19.761266] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input8
[   19.905974] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 op_mode iwldvm
[   20.315359] psmouse serio1: synaptics: queried max coordinates: x [..5888], y [..4820]
[   20.396941] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd047b3/0xb40000/0xa0000/0x0, board id: 0, fw id: 578367
[   20.396946] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
[   20.447588] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[   20.554235] iTCO_vendor_support: vendor-support=0
[   20.587732] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   20.587768] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[   20.587870] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   20.771029] Console: switching to colour frame buffer device 170x48
[   20.791213] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[   20.887827] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled
[   20.887828] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS disabled
[   20.887829] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
[   20.887831] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6205 AGN, REV=0xB0
[   20.889918] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[   20.975324] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[   21.085031] kvm: disabled by bios
[   21.129720] e1000e 0000:00:19.0 enp0s25: renamed from eth0
[   21.134456] kvm: disabled by bios
[   21.171120] kvm: disabled by bios
[   21.207826] kvm: disabled by bios
[   21.210631] psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
[   21.469971] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input9
[   21.551888] snd_hda_codec_conexant hdaudioC0D0: CX20590: BIOS auto-probing.
[   21.552362] snd_hda_codec_conexant hdaudioC0D0: autoconfig for CX20590: line_outs=1 (0x1f/0x0/0x0/0x0/0x0) type:speaker
[   21.552364] snd_hda_codec_conexant hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   21.552366] snd_hda_codec_conexant hdaudioC0D0:    hp_outs=2 (0x1c/0x19/0x0/0x0/0x0)
[   21.552367] snd_hda_codec_conexant hdaudioC0D0:    mono: mono_out=0x0
[   21.552368] snd_hda_codec_conexant hdaudioC0D0:    inputs:
[   21.552370] snd_hda_codec_conexant hdaudioC0D0:      Internal Mic=0x23
[   21.552371] snd_hda_codec_conexant hdaudioC0D0:      Mic=0x1b
[   21.552372] snd_hda_codec_conexant hdaudioC0D0:      Dock Mic=0x1a
[   21.553678] snd_hda_codec_conexant hdaudioC0D0: Enable sync_write for stable communication
[   21.630590] intel_rapl: Found RAPL domain package
[   21.630592] intel_rapl: Found RAPL domain core
[   21.630593] intel_rapl: Found RAPL domain uncore
[   21.630598] intel_rapl: RAPL package 0 domain package locked by BIOS
[   21.667627] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0
[   21.763822] mousedev: PS/2 mouse device common for all mice
[   21.804956] Adding 8388604k swap on /dev/sda3.  Priority:-1 extents:1 across:8388604k FS
[   21.875654] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops vgt_balloon_space [i915])
[   21.882169] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   21.882742] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   21.882867] input: HDA Intel PCH Dock Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   21.882984] input: HDA Intel PCH Dock Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[   21.883103] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[   21.883222] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[   21.883342] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[   21.883457] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[   24.303862] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: data=ordered
[   24.871097] Bluetooth: Core ver 2.21
[   24.871109] NET: Registered protocol family 31
[   24.871110] Bluetooth: HCI device and connection manager initialized
[   24.871112] Bluetooth: HCI socket layer initialized
[   24.871114] Bluetooth: L2CAP socket layer initialized
[   24.871118] Bluetooth: SCO socket layer initialized
[   24.908540] usbcore: registered new interface driver btusb
[   26.028571] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
[   26.582146] media: Linux media interface: v0.10
[   26.640448] Linux video capture interface: v2.00
[   26.870207] uvcvideo: Found UVC 1.00 device Integrated Camera (04f2:b221)
[   26.872047] uvcvideo 1-1.6:1.0: Entity type for entity Extension 3 was not initialized!
[   26.872051] uvcvideo 1-1.6:1.0: Entity type for entity Processing 2 was not initialized!
[   26.872053] uvcvideo 1-1.6:1.0: Entity type for entity Camera 1 was not initialized!
[   26.872150] input: Integrated Camera as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input18
[   26.872228] usbcore: registered new interface driver uvcvideo
[   26.872229] USB Video Class driver (1.1.1)
[   27.721949] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[   27.722191] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[   27.722287] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[   27.997262] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[   27.997536] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[   27.997638] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[   28.078070] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[   31.375327] wlp3s0: authenticate with 84:61:a0:c8:68:e0
[   31.378873] wlp3s0: send auth to 84:61:a0:c8:68:e0 (try 1/3)
[   31.381659] wlp3s0: authenticated
[   31.384433] wlp3s0: associate with 84:61:a0:c8:68:e0 (try 1/3)
[   31.387806] wlp3s0: RX AssocResp from 84:61:a0:c8:68:e0 (capab=0x411 status=0 aid=7)
[   31.406830] wlp3s0: associated
[   31.406873] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[11151.340153] device-mapper: table: 254:1: adding target device sdb1 caused an alignment inconsistency: physical_block_size=4096, logical_block_size=512, alignment_offset=0, start=33553920
[11151.340155] device-mapper: table: 254:1: adding target device sdb1 caused an alignment inconsistency: physical_block_size=4096, logical_block_size=512, alignment_offset=0, start=33553920
[11160.238624] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[27624.383813] perf: interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 79800
[34795.877239] perf: interrupt took too long (3167 > 3132), lowering kernel.perf_event_max_sample_rate to 63000
[48919.378364] PM: Syncing filesystems ... done.
[48920.483535] PM: Preparing system for sleep (mem)
[48920.483886] Freezing user space processes ... (elapsed 0.001 seconds) done.
[48920.485077] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) 
[48920.485122] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[48920.486283] PM: Suspending system (mem)
[48920.486305] Suspending console(s) (use no_console_suspend to debug)
[48920.486527] wlp3s0: deauthenticating from 84:61:a0:c8:68:e0 by local choice (Reason: 3=DEAUTH_LEAVING)
[48920.651783] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[48920.655241] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[48920.664134] sd 0:0:0:0: [sda] Stopping disk
[48920.888607] e1000e: EEE TX LPI TIMER: 00000011
[48921.258136] PM: suspend of devices complete after 771.608 msecs
[48921.275166] PM: late suspend of devices complete after 17.022 msecs
[48921.276182] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[48921.276424] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[48921.276430] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[48921.291995] PM: noirq suspend of devices complete after 16.824 msecs
[48921.292348] ACPI: Preparing to enter system sleep state S3
[48921.591792] ACPI : EC: EC stopped
[48921.591793] PM: Saving platform NVS memory
[48921.591806] Disabling non-boot CPUs ...
[48921.623326] smpboot: CPU 1 is now offline
[48921.657185] smpboot: CPU 2 is now offline
[48921.686484] smpboot: CPU 3 is now offline
[48921.688656] ACPI: Low-level resume complete
[48921.688698] ACPI : EC: EC started
[48921.688698] PM: Restoring platform NVS memory
[48921.689060] Enabling non-boot CPUs ...
[48921.689096] x86: Booting SMP configuration:
[48921.689097] smpboot: Booting Node 0 Processor 1 APIC 0x1
[48921.689391] Disabled fast string operations
[48921.797008]  cache: parent cpu1 should not be sleeping
[48921.797341] CPU1 is up
[48921.797394] smpboot: Booting Node 0 Processor 2 APIC 0x2
[48921.798098] Disabled fast string operations
[48921.907014]  cache: parent[48921.907404] CPU2 is up
[48921.907456] smpboot: Booting Node 0 Processor 3 APIC 0x3
[48921.907780] Disabled fast string operations
[48922.013685]  cache: parent cpu3 should not be sleeping
[48922.014086] CPU3 is up
[48922.022121] ACPI: Waking up from system sleep state S3
[48922.597291] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[48922.598017] sdhci-pci 0000:0d:00.0: MMC controller base frequency changed to 50Mhz.
[48922.607149] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[48922.607313] PM: noirq resume of devices complete after 27.024 msecs
[48922.608056] PM: early resume of devices complete after 0.687 msecs
[48922.608124] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[48922.609136] rtc_cmos 00:02: System wakeup disabled by ACPI
[48922.609504] sd 0:0:0:0: [sda] Starting disk
[48922.611401] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[48922.611684] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[48922.611786] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[48922.646987] tpm tpm0: TPM is disabled/deactivated (0x6)
[48922.843644] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[48922.890385] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[48922.890628] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[48922.890728] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[48922.949986] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[48922.950018] ata4: SATA link down (SStatus 0 SControl 300)
[48922.950053] ata5: SATA link down (SStatus 0 SControl 300)
[48923.013648] usb 1-1.4: reset full-speed USB device number 4 using ehci-pci
[48923.136993] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[48923.137809] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[48923.137813] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[48923.152310] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[48923.152744] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[48923.152748] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[48923.154424] ata2.00: configured for UDMA/100
[48923.167031] firewire_core 0000:0d:00.3: rediscovered device fw0
[48923.183633] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[48923.292364] PM: resume of devices complete after 684.254 msecs
[48923.292484] usb 1-1.4:1.0: rebind failed: -517
[48923.292498] usb 1-1.4:1.1: rebind failed: -517
[48923.381292] psmouse serio1: synaptics: queried max coordinates: x [..5888], y [..4820]
[48923.405128] PM: Finishing wakeup.
[48923.405131] Restarting tasks ... done.
[48923.449555] video LNXVIDEO:00: Restoring backlight state
[48924.760442] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[48924.903949] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[48924.903955] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[48924.903960] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[48924.944725] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[48924.944730] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[48924.944734] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[48924.948500] ata1.00: configured for UDMA/133
[48926.592043] wlp3s0: authenticate with 84:61:a0:c8:68:e0
[48926.595170] wlp3s0: send auth to 84:61:a0:c8:68:e0 (try 1/3)
[48926.597912] wlp3s0: authenticated
[48926.600555] wlp3s0: associate with 84:61:a0:c8:68:e0 (try 1/3)
[48926.603913] wlp3s0: RX AssocResp from 84:61:a0:c8:68:e0 (capab=0x411 status=0 aid=2) cpu2 should not be sleeping
[48926.623995] wlp3s0: associated
[54498.149619] perf: interrupt took too long (3976 > 3958), lowering kernel.perf_event_max_sample_rate to 50100
[102208.317252] perf: interrupt took too long (4985 > 4970), lowering kernel.perf_event_max_sample_rate to 39900
[124529.323897] PM: Syncing filesystems ... done.
[124530.773134] PM: Preparing system for sleep (mem)
[124530.773698] Freezing user space processes ... (elapsed 0.001 seconds) done.
[124530.775206] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) 
[124530.775306] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[124530.776606] PM: Suspending system (mem)
[124530.776646] Suspending console(s) (use no_console_suspend to debug)
[124530.777136] wlp3s0: deauthenticating from 84:61:a0:c8:68:e0 by local choice (Reason: 3=DEAUTH_LEAVING)
[124530.941115] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[124530.941488] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[124530.990295] sd 0:0:0:0: [sda] Stopping disk
[124531.178665] e1000e: EEE TX LPI TIMER: 00000011
[124531.583301] PM: suspend of devices complete after 806.286 msecs
[124531.598543] PM: late suspend of devices complete after 15.235 msecs
[124531.601822] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[124531.601977] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[124531.601992] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[124531.621807] PM: noirq suspend of devices complete after 23.243 msecs
[124531.622266] ACPI: Preparing to enter system sleep state S3
[124531.921870] ACPI : EC: EC stopped
[124531.921871] PM: Saving platform NVS memory
[124531.921895] Disabling non-boot CPUs ...
[124531.943772] smpboot: CPU 1 is now offline
[124531.973303] smpboot: CPU 2 is now offline
[124531.999883] smpboot: CPU 3 is now offline
[124532.002040] ACPI: Low-level resume complete
[124532.002084] ACPI : EC: EC started
[124532.002084] PM: Restoring platform NVS memory
[124532.002443] Enabling non-boot CPUs ...
[124532.002481] x86: Booting SMP configuration:
[124532.002481] smpboot: Booting Node 0 Processor 1 APIC 0x1
[124532.002874] Disabled fast string operations
[124532.113712]  cache: parent cpu1 should not be sleeping
[124532.114064] CPU1 is up
[124532.114120] smpboot: Booting Node 0 Processor 2 APIC 0x2
[124532.114823] Disabled fast string operations
[124532.223716]  cache: parent cpu2 should not be sleeping
[124532.224116] CPU2 is up
[124532.224169] smpboot: Booting Node 0 Processor 3 APIC 0x3
[124532.224868] Disabled fast string operations
[124532.337055]  cache: parent cpu3 should not be sleeping
[124532.337468] CPU3 is up
[124532.345510] ACPI: Waking up from system sleep state S3
[124532.923964] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[124532.924087] sdhci-pci 0000:0d:00.0: MMC controller base frequency changed to 50Mhz.
[124532.927173] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[124532.927335] PM: noirq resume of devices complete after 20.346 msecs
[124532.927914] PM: early resume of devices complete after 0.543 msecs
[124532.927977] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[124532.929408] rtc_cmos 00:02: System wakeup disabled by ACPI
[124532.930510] sd 0:0:0:0: [sda] Starting disk
[124532.931654] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[124532.931944] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[124532.932046] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[124532.966997] tpm tpm0: TPM is disabled/deactivated (0x6)
[124533.163702] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[124533.211136] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[124533.211388] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[124533.211488] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[124533.269987] ata4: SATA link down (SStatus 0 SControl 300)
[124533.270019] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[124533.270052] ata5: SATA link down (SStatus 0 SControl 300)
[124533.333699] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[124533.451911] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[124533.452731] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[124533.452736] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[124533.467237] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[124533.467668] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[124533.467672] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[124533.469634] ata2.00: configured for UDMA/100
[124533.507008] usb 1-1.4: reset full-speed USB device number 4 using ehci-pci
[124533.520381] firewire_core 0000:0d:00.3: rediscovered device fw0
[124533.613022] PM: resume of devices complete after 685.053 msecs
[124533.613142] usb 1-1.4:1.0: rebind failed: -517
[124533.613155] usb 1-1.4:1.1: rebind failed: -517
[124533.699366] psmouse serio1: synaptics: queried max coordinates: x [..5888], y [..4820]
[124533.722467] PM: Finishing wakeup.
[124533.722470] Restarting tasks ... done.
[124533.765546] video LNXVIDEO:00: Restoring backlight state
[124535.080463] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[124535.217141] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[124535.217147] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[124535.217160] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[124535.257951] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[124535.257967] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[124535.257971] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[124535.261235] ata1.00: configured for UDMA/133
[124536.957625] wlp3s0: authenticate with 84:61:a0:c8:68:e0
[124536.961103] wlp3s0: send auth to 84:61:a0:c8:68:e0 (try 1/3)
[124536.967154] wlp3s0: authenticated
[124536.970591] wlp3s0: associate with 84:61:a0:c8:68:e0 (try 1/3)
[124536.981489] wlp3s0: RX AssocResp from 84:61:a0:c8:68:e0 (capab=0x411 status=0 aid=1)
[124537.000513] wlp3s0: associated
[133215.657527] usb 1-1.2: new high-speed USB device number 6 using ehci-pci
[133215.767220] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[133215.767620] scsi host7: usb-storage 1-1.2:1.0
[133216.775601] scsi 7:0:0:0: Direct-Access     Kindle   Internal Storage 0100 PQ: 0 ANSI: 2
[133216.784591] sd 7:0:0:0: [sdc] Attached SCSI removable disk
[133218.994084] sd 7:0:0:0: [sdc] 6385664 512-byte logical blocks: (3.27 GB/3.04 GiB)
[133219.214769] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[133219.435860]  sdc: sdc1
[133668.319277] usb 1-1.2: USB disconnect, device number 6
[135724.612505] usb 1-1.2: new high-speed USB device number 7 using ehci-pci
[135724.718402] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[135724.718602] scsi host7: usb-storage 1-1.2:1.0
[135725.720529] scsi 7:0:0:0: Direct-Access     Kindle   Internal Storage 0100 PQ: 0 ANSI: 2
[135725.731015] sd 7:0:0:0: [sdc] 6385664 512-byte logical blocks: (3.27 GB/3.04 GiB)
[135725.841253] sd 7:0:0:0: [sdc] Write Protect is off
[135725.841256] sd 7:0:0:0: [sdc] Mode Sense: 0f 00 00 00
[135725.951285] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[135726.172299]  sdc: sdc1
[135726.391307] sd 7:0:0:0: [sdc] Attached SCSI removable disk
[135956.357901] usb 1-1.2: USB disconnect, device number 7
[135956.360336] sd 7:0:0:0: [sdc] Synchronizing SCSI cache
[135956.360414] sd 7:0:0:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x01 driverbyte=0x00
[161390.081158] PM: Syncing filesystems ... done.
[161390.937065] PM: Preparing system for sleep (mem)
[161390.937634] Freezing user space processes ... (elapsed 0.001 seconds) done.
[161390.939536] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) 
[161390.939632] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[161390.940953] PM: Suspending system (mem)
[161390.940992] Suspending console(s) (use no_console_suspend to debug)
[161390.941503] wlp3s0: deauthenticating from 84:61:a0:c8:68:e0 by local choice (Reason: 3=DEAUTH_LEAVING)
[161391.104398] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[161391.104794] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[161391.105034] sd 0:0:0:0: [sda] Stopping disk
[161391.341568] e1000e: EEE TX LPI TIMER: 00000011
[161391.698201] PM: suspend of devices complete after 756.785 msecs
[161391.714788] PM: late suspend of devices complete after 16.578 msecs
[161391.718086] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[161391.718350] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[161391.718502] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[161391.738065] PM: noirq suspend of devices complete after 23.269 msecs
[161391.738743] ACPI: Preparing to enter system sleep state S3
[161392.038126] ACPI : EC: EC stopped
[161392.038127] PM: Saving platform NVS memory
[161392.038151] Disabling non-boot CPUs ...
[161392.066283] smpboot: CPU 1 is now offline
[161392.096943] smpboot: CPU 2 is now offline
[161392.126111] smpboot: CPU 3 is now offline
[161392.128304] ACPI: Low-level resume complete
[161392.128348] ACPI : EC: EC started
[161392.128348] PM: Restoring platform NVS memory
[161392.128716] Enabling non-boot CPUs ...
[161392.128753] x86: Booting SMP configuration:
[161392.128754] smpboot: Booting Node 0 Processor 1 APIC 0x1
[161392.129141] Disabled fast string operations
[161392.239967]  cache: parent cpu1 should not be sleeping
[161392.240316] CPU1 is up
[161392.240372] smpboot: Booting Node 0 Processor 2 APIC 0x2
[161392.241075] Disabled fast string operations
[161392.349973]  cache: parent cpu2 should not be sleeping
[161392.350366] CPU2 is up
[161392.350420] smpboot: Booting Node 0 Processor 3 APIC 0x3
[161392.351119] Disabled fast string operations
[161392.483313]  cache: parent cpu3 should not be sleeping
[161392.483739] CPU3 is up
[161392.487129] ACPI: Waking up from system sleep state S3
[161393.066426] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[161393.066430] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[161393.077002] sdhci-pci 0000:0d:00.0: MMC controller base frequency changed to 50Mhz.
[161393.077150] PM: noirq resume of devices complete after 30.570 msecs
[161393.077579] PM: early resume of devices complete after 0.398 msecs
[161393.077647] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[161393.079003] rtc_cmos 00:02: System wakeup disabled by ACPI
[161393.085908] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[161393.086229] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[161393.086331] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[161393.089156] sd 0:0:0:0: [sda] Starting disk
[161393.116606] tpm tpm0: TPM is disabled/deactivated (0x6)
[161393.313263] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[161393.363919] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[161393.364180] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[161393.364281] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[161393.429555] ata4: SATA link down (SStatus 0 SControl 300)
[161393.429610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[161393.429637] ata5: SATA link down (SStatus 0 SControl 300)
[161393.483274] usb 1-1.4: reset full-speed USB device number 4 using ehci-pci
[161393.579389] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[161393.580211] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[161393.580216] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[161393.594712] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[161393.595149] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[161393.595153] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[161393.596825] ata2.00: configured for UDMA/100
[161393.640071] firewire_core 0000:0d:00.3: rediscovered device fw0
[161393.656604] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[161393.765650] PM: resume of devices complete after 688.017 msecs
[161393.765757] usb 1-1.4:1.0: rebind failed: -517
[161393.765769] usb 1-1.4:1.1: rebind failed: -517
[161393.848373] PM: Finishing wakeup.
[161393.848375] Restarting tasks ... 
[161393.853116] psmouse serio1: synaptics: queried max coordinates: x [..5888], y [..4820]
[161393.867664] done.
[161393.884692] video LNXVIDEO:00: Restoring backlight state
[161395.260068] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[161395.400127] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[161395.400133] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[161395.400137] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[161395.440912] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[161395.440918] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[161395.440922] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[161395.444226] ata1.00: configured for UDMA/133
[161397.097738] wlp3s0: authenticate with 84:61:a0:c8:68:e0
[161397.099310] wlp3s0: send auth to 84:61:a0:c8:68:e0 (try 1/3)
[161397.102075] wlp3s0: authenticated
[161397.103519] wlp3s0: associate with 84:61:a0:c8:68:e0 (try 1/3)
[161397.115122] wlp3s0: RX AssocResp from 84:61:a0:c8:68:e0 (capab=0x411 status=0 aid=1)
[161397.135282] wlp3s0: associated
[193514.623478] usb 2-1.2: USB disconnect, device number 3
[193514.625125] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[193514.823648] sd 6:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=0x07 driverbyte=0x00
[193515.047006] usb 2-1.2: new high-speed USB device number 4 using ehci-pci
[193515.204094] scsi host7: uas
[193515.205527] scsi 7:0:0:0: Direct-Access     Seagate  BUP BK           0304 PQ: 0 ANSI: 6
[193515.244909] sd 7:0:0:0: [sdc] 7814037167 512-byte logical blocks: (4.00 TB/3.64 TiB)
[193515.244916] sd 7:0:0:0: [sdc] 4096-byte physical blocks
[193519.931961] sd 7:0:0:0: [sdc] Write Protect is off
[193519.931971] sd 7:0:0:0: [sdc] Mode Sense: 4f 00 00 00
[193519.932682] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[193520.190153]  sdc: sdc1
[193520.193846] sd 7:0:0:0: [sdc] Attached SCSI disk
[194022.721798] Aborting journal on device dm-1-8.
[194022.721818] Buffer I/O error on dev dm-1, logical block 488144896, lost sync page write
[194022.721823] JBD2: Error -5 detected when updating journal superblock for dm-1-8.
[194051.285814] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[194051.285841] EXT4-fs error (device dm-1): ext4_journal_check_start:56: Detected aborted journal
[194051.285852] EXT4-fs (dm-1): Remounting filesystem read-only
[194051.285860] EXT4-fs (dm-1): previous I/O error to superblock detected
[194051.285902] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[194148.294247] EXT4-fs (dm-1): previous I/O error to superblock detected
[194148.294290] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[194148.294296] EXT4-fs error (device dm-1): ext4_put_super:837: Couldn't clean up the journal
[194160.381514] Buffer I/O error on dev dm-1, logical block 7813969408, async page read
[194160.381520] Buffer I/O error on dev dm-1, logical block 7813969409, async page read
[194160.381522] Buffer I/O error on dev dm-1, logical block 7813969410, async page read
[194160.381524] Buffer I/O error on dev dm-1, logical block 7813969411, async page read
[194160.381526] Buffer I/O error on dev dm-1, logical block 7813969412, async page read
[194160.381528] Buffer I/O error on dev dm-1, logical block 7813969413, async page read
[194160.381530] Buffer I/O error on dev dm-1, logical block 7813969414, async page read
[194160.381532] Buffer I/O error on dev dm-1, logical block 7813969415, async page read
[194160.381654] EXT4-fs (dm-1): unable to read superblock
[194160.381685] EXT4-fs (dm-1): unable to read superblock
[194160.381705] EXT4-fs (dm-1): unable to read superblock
[194160.381726] FAT-fs (dm-1): unable to read boot sector
[194177.448542] usb 2-1.2: USB disconnect, device number 4
[194177.449290] sd 7:0:0:0: [sdc] Synchronizing SCSI cache
[194177.649000] sd 7:0:0:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x07 driverbyte=0x00
[194180.469185] usb 2-1.2: new high-speed USB device number 5 using ehci-pci
[194180.626316] scsi host6: uas
[194180.627763] scsi 6:0:0:0: Direct-Access     Seagate  BUP BK           0304 PQ: 0 ANSI: 6
[194180.666861] sd 6:0:0:0: [sdb] Spinning up disk...
[194181.692603] .....ready
[194185.746822] sd 6:0:0:0: [sdb] 7814037167 512-byte logical blocks: (4.00 TB/3.64 TiB)
[194185.746827] sd 6:0:0:0: [sdb] 2048-byte physical blocks
[194185.781593] sd 6:0:0:0: [sdb] Write Protect is off
[194185.781600] sd 6:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[194185.782306] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[194185.957781]  sdb: sdb1
[194185.961338] sd 6:0:0:0: [sdb] Attached SCSI disk
[194209.627689] device-mapper: table: 254:1: adding target device sdb1 caused an alignment inconsistency: physical_block_size=4096, logical_block_size=512, alignment_offset=0, start=33553920
[194209.627691] device-mapper: table: 254:1: adding target device sdb1 caused an alignment inconsistency: physical_block_size=4096, logical_block_size=512, alignment_offset=0, start=33553920
[194220.820636] EXT4-fs (dm-1): recovery complete
[194220.836256] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[203542.200563] PM: Syncing filesystems ... done.
[203543.152809] PM: Preparing system for sleep (mem)
[203543.153178] Freezing user space processes ... (elapsed 0.001 seconds) done.
[203543.154801] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) 
[203543.154859] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[203543.156075] PM: Suspending system (mem)
[203543.156100] Suspending console(s) (use no_console_suspend to debug)
[203543.156368] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[203543.156623] wlp3s0: deauthenticating from 84:61:a0:c8:68:e0 by local choice (Reason: 3=DEAUTH_LEAVING)
[203543.329613] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[203543.349777] sd 0:0:0:0: [sda] Stopping disk
[203543.566458] e1000e: EEE TX LPI TIMER: 00000011
[203544.048887] PM: suspend of devices complete after 892.480 msecs
[203544.063023] PM: late suspend of devices complete after 14.127 msecs
[203544.066298] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[203544.066516] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[203544.066526] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[203544.086325] PM: noirq suspend of devices complete after 23.286 msecs
[203544.086807] ACPI: Preparing to enter system sleep state S3
[203544.386360] ACPI : EC: EC stopped
[203544.386362] PM: Saving platform NVS memory
[203544.386385] Disabling non-boot CPUs ...
[203544.415097] smpboot: CPU 1 is now offline
[203544.441151] smpboot: CPU 2 is now offline
[203544.457719] smpboot: CPU 3 is now offline
[203544.459769] ACPI: Low-level resume complete
[203544.459811] ACPI : EC: EC started
[203544.459812] PM: Restoring platform NVS memory
[203544.460181] Enabling non-boot CPUs ...
[203544.460218] x86: Booting SMP configuration:
[203544.460219] smpboot: Booting Node 0 Processor 1 APIC 0x1
[203544.460606] Disabled fast string operations
[203544.571543]  cache: parent cpu1 should not be sleeping
[203544.571886] CPU1 is up
[203544.571941] smpboot: Booting Node 0 Processor 2 APIC 0x2
[203544.572644] Disabled fast string operations
[203544.681546]  cache: parent cpu2 should not be sleeping
[203544.681953] CPU2 is up
[203544.682005] smpboot: Booting Node 0 Processor 3 APIC 0x3
[203544.682346] Disabled fast string operations
[203544.808220]  cache: parent cpu3 should not be sleeping
[203544.808648] CPU3 is up
[203544.812043] ACPI: Waking up from system sleep state S3
[203545.388476] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[203545.388731] sdhci-pci 0000:0d:00.0: MMC controller base frequency changed to 50Mhz.
[203545.401777] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[203545.401862] PM: noirq resume of devices complete after 30.375 msecs
[203545.402289] PM: early resume of devices complete after 0.393 msecs
[203545.402942] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[203545.405176] rtc_cmos 00:02: System wakeup disabled by ACPI
[203545.406449] sd 0:0:0:0: [sda] Starting disk
[203545.408180] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[203545.408501] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[203545.408617] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[203545.444855] tpm tpm0: TPM is disabled/deactivated (0x6)
[203545.641535] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[203545.684195] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[203545.684447] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[203545.684547] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[203545.747843] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[203545.747896] ata5: SATA link down (SStatus 0 SControl 300)
[203545.748034] ata4: SATA link down (SStatus 0 SControl 300)
[203545.811546] usb 1-1.4: reset full-speed USB device number 4 using ehci-pci
[203545.911264] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[203545.912070] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[203545.912074] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[203545.926571] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[203545.927004] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[203545.927008] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[203545.928681] ata2.00: configured for UDMA/100
[203545.984832] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[203545.988182] firewire_core 0000:0d:00.3: rediscovered device fw0
[203546.093723] PM: resume of devices complete after 691.381 msecs
[203546.093836] usb 1-1.4:1.0: rebind failed: -517
[203546.093849] usb 1-1.4:1.1: rebind failed: -517
[203546.178467] psmouse serio1: synaptics: queried max coordinates: x [..5888], y [..4820]
[203546.179409] PM: Finishing wakeup.
[203546.179412] Restarting tasks ... done.
[203546.216778] video LNXVIDEO:00: Restoring backlight state
[203547.568282] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[203547.703146] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[203547.703149] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[203547.703150] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[203547.743985] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[203547.743992] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[203547.743996] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[203547.747570] ata1.00: configured for UDMA/133
[203549.440924] wlp3s0: authenticate with 84:61:a0:c8:68:e0
[203549.442489] wlp3s0: send auth to 84:61:a0:c8:68:e0 (try 1/3)
[203549.445193] wlp3s0: authenticated
[203549.448450] wlp3s0: associate with 84:61:a0:c8:68:e0 (try 1/3)
[203549.469656] wlp3s0: RX AssocResp from 84:61:a0:c8:68:e0 (capab=0x411 status=0 aid=6)
[203549.489468] wlp3s0: associated
[218830.726046] EXT4-fs (dm-0): re-mounted. Opts: data=ordered,commit=600
[218830.764645] EXT4-fs (sda1): re-mounted. Opts: data=ordered,commit=600
[218830.790440] EXT4-fs (dm-1): re-mounted. Opts: data=ordered,commit=600
[220133.350909] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[220133.378728] EXT4-fs (dm-0): re-mounted. Opts: data=ordered,commit=0
[220133.440582] EXT4-fs (sda1): re-mounted. Opts: data=ordered,commit=0
[220133.486635] EXT4-fs (dm-1): re-mounted. Opts: data=ordered,commit=0
[220133.615684] ata4: SATA link down (SStatus 0 SControl 300)
[220133.939116] ata5: SATA link down (SStatus 0 SControl 300)
[260105.542148] PM: Syncing filesystems ... done.
[260106.320715] PM: Preparing system for sleep (mem)
[260106.320967] Freezing user space processes ... (elapsed 0.001 seconds) done.
[260106.322405] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) 
[260106.322504] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[260106.323591] PM: Suspending system (mem)
[260106.323631] Suspending console(s) (use no_console_suspend to debug)
[260106.324033] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[260106.324244] wlp3s0: deauthenticating from 84:61:a0:c8:68:e0 by local choice (Reason: 3=DEAUTH_LEAVING)
[260106.488302] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[260106.491813] sd 0:0:0:0: [sda] Stopping disk
[260106.723800] e1000e: EEE TX LPI TIMER: 00000011
[260107.083948] PM: suspend of devices complete after 759.950 msecs
[260107.100262] PM: late suspend of devices complete after 16.308 msecs
[260107.103460] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[260107.103702] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[260107.103729] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[260107.123542] PM: noirq suspend of devices complete after 23.269 msecs
[260107.124211] ACPI: Preparing to enter system sleep state S3
[260107.423602] ACPI : EC: EC stopped
[260107.423603] PM: Saving platform NVS memory
[260107.423627] Disabling non-boot CPUs ...
[260107.452108] smpboot: CPU 1 is now offline
[260107.471695] smpboot: CPU 2 is now offline
[260107.498281] smpboot: CPU 3 is now offline
[260107.500880] ACPI: Low-level resume complete
[260107.500923] ACPI : EC: EC started
[260107.500923] PM: Restoring platform NVS memory
[260107.501278] Enabling non-boot CPUs ...
[260107.501315] x86: Booting SMP configuration:
[260107.501316] smpboot: Booting Node 0 Processor 1 APIC 0x1
[260107.501611] Disabled fast string operations
[260107.612038]  cache: parent cpu1 should not be sleeping
[260107.612381] CPU1 is up
[260107.612435] smpboot: Booting Node 0 Processor 2 APIC 0x2
[260107.613146] Disabled fast string operations
[260107.722040]  cache: parent cpu2 should not be sleeping
[260107.722441] CPU2 is up
[260107.722494] smpboot: Booting Node 0 Processor 3 APIC 0x3
[260107.723289] Disabled fast string operations
[260107.852045]  cache: parent cpu3 should not be sleeping
[260107.852477] CPU3 is up
[260107.860503] ACPI: Waking up from system sleep state S3
[260108.437351] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[260108.439205] sdhci-pci 0000:0d:00.0: MMC controller base frequency changed to 50Mhz.
[260108.439264] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[260108.445541] PM: noirq resume of devices complete after 26.885 msecs
[260108.445998] PM: early resume of devices complete after 0.425 msecs
[260108.446563] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[260108.448880] rtc_cmos 00:02: System wakeup disabled by ACPI
[260108.451848] sd 0:0:0:0: [sda] Starting disk
[260108.453654] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[260108.453918] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[260108.454017] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[260108.488697] tpm tpm0: TPM is disabled/deactivated (0x6)
[260108.685359] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[260108.732036] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[260108.732288] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[260108.732385] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[260108.791593] ata5: SATA link down (SStatus 0 SControl 300)
[260108.791729] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[260108.791770] ata4: SATA link down (SStatus 0 SControl 300)
[260108.855321] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[260108.951419] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[260108.952236] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[260108.952240] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[260108.966746] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[260108.967179] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[260108.967183] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[260108.968858] ata2.00: configured for UDMA/100
[260109.032010] firewire_core 0000:0d:00.3: rediscovered device fw0
[260109.035460] usb 1-1.4: reset full-speed USB device number 4 using ehci-pci
[260109.134537] PM: resume of devices complete after 688.487 msecs
[260109.134662] usb 1-1.4:1.0: rebind failed: -517
[260109.134674] usb 1-1.4:1.1: rebind failed: -517
[260109.220464] PM: Finishing wakeup.
[260109.220466] Restarting tasks ... 
[260109.228712] psmouse serio1: synaptics: queried max coordinates: x [..5888], y [..4820]
[260109.235976] done.
[260109.259661] video LNXVIDEO:00: Restoring backlight state
[260110.662121] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[260110.797033] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[260110.797041] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[260110.797046] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[260110.837656] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[260110.837657] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[260110.837658] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[260110.841616] ata1.00: configured for UDMA/133
[260112.495723] wlp3s0: authenticate with 84:61:a0:c8:68:e0
[260112.499229] wlp3s0: send auth to 84:61:a0:c8:68:e0 (try 1/3)
[260112.501953] wlp3s0: authenticated
[260112.502228] wlp3s0: associate with 84:61:a0:c8:68:e0 (try 1/3)
[260112.505580] wlp3s0: RX AssocResp from 84:61:a0:c8:68:e0 (capab=0x411 status=0 aid=4)
[260112.528216] wlp3s0: associated
[275479.089074] Chrome_ChildThr[12474]: segfault at 0 ip 00005631d37b9129 sp 00007fcf405fe350 error 6 in plugin-container[5631d37b0000+3e000]
[302713.547356] PM: Syncing filesystems ... done.
[302714.315193] PM: Preparing system for sleep (mem)
[302714.365188] Freezing user space processes ... (elapsed 0.001 seconds) done.
[302714.366813] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) 
[302714.366878] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[302714.368108] PM: Suspending system (mem)
[302714.368136] Suspending console(s) (use no_console_suspend to debug)
[302714.368403] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[302714.368568] wlp3s0: deauthenticating from 84:61:a0:c8:68:e0 by local choice (Reason: 3=DEAUTH_LEAVING)
[302714.539244] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[302714.539511] sd 0:0:0:0: [sda] Stopping disk
[302714.779755] e1000e: EEE TX LPI TIMER: 00000011
[302715.132657] PM: suspend of devices complete after 764.254 msecs
[302715.149616] PM: late suspend of devices complete after 16.951 msecs
[302715.152735] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[302715.153201] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[302715.153211] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[302715.172881] PM: noirq suspend of devices complete after 23.259 msecs
[302715.173372] ACPI: Preparing to enter system sleep state S3
[302715.472931] ACPI : EC: EC stopped
[302715.472933] PM: Saving platform NVS memory
[302715.472957] Disabling non-boot CPUs ...
[302715.498286] smpboot: CPU 1 is now offline
[302715.544383] smpboot: CPU 2 is now offline
[302715.570940] smpboot: CPU 3 is now offline
[302715.573064] ACPI: Low-level resume complete
[302715.573106] ACPI : EC: EC started
[302715.573107] PM: Restoring platform NVS memory
[302715.573469] Enabling non-boot CPUs ...
[302715.573505] x86: Booting SMP configuration:
[302715.573506] smpboot: Booting Node 0 Processor 1 APIC 0x1
[302715.573800] Disabled fast string operations
[302715.684782]  cache: parent cpu1 should not be sleeping
[302715.685123] CPU1 is up
[302715.685177] smpboot: Booting Node 0 Processor 2 APIC 0x2
[302715.685880] Disabled fast string operations
[302715.794783]  cache: parent cpu2 should not be sleeping
[302715.795187] CPU2 is up
[302715.795240] smpboot: Booting Node 0 Processor 3 APIC 0x3
[302715.795580] Disabled fast string operations
[302715.914789]  cache: parent cpu3 should not be sleeping
[302715.915223] CPU3 is up
[302715.918614] ACPI: Waking up from system sleep state S3
[302716.499237] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[302716.499293] sdhci-pci 0000:0d:00.0: MMC controller base frequency changed to 50Mhz.
[302716.499457] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[302716.508126] PM: noirq resume of devices complete after 30.058 msecs
[302716.508852] PM: early resume of devices complete after 0.680 msecs
[302716.508938] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[302716.510119] rtc_cmos 00:02: System wakeup disabled by ACPI
[302716.510879] sd 0:0:0:0: [sda] Starting disk
[302716.512972] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[302716.513251] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[302716.513352] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[302716.548088] tpm tpm0: TPM is disabled/deactivated (0x6)
[302716.744794] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[302716.792197] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[302716.792451] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[302716.792551] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[302716.851041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[302716.851090] ata5: SATA link d[302717.023594] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[302717.024410] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[302717.024414] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[302717.038914] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[302717.039343] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[302717.039348] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[302717.041023] ata2.00: configured for UDMA/100
[302717.068116] firewire_core 0000:0d:00.3: rediscovered device fw0
[302717.084761] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[302717.193522] PM: resume of devices complete after 684.616 msecs
[302717.193647] usb 1-1.4:1.0: rebind failed: -517
[302717.193660] usb 1-1.4:1.1: rebind failed: -517
[302717.281942] psmouse serio1: synaptics: queried max coordinates: x [..5888], y [..4820]
[302717.293318] PM: Finishing wakeup.
[302717.293320] Restarting tasks ... done.
[302717.321918] video LNXVIDEO:00: Restoring backlight state
[302718.661529] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[302718.797002] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[302718.797010] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[302718.797014] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[302718.837833] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[302718.837838] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[302718.837843] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[302718.841773] ata1.00: configured for UDMA/133
[302720.585828] wlp3s0: authenticate with 84:61:a0:c8:68:e0
[302720.588320] wlp3s0: send auth to 84:61:a0:c8:68:e0 (try 1/3)
[302720.591162] wlp3s0: authenticated
[302720.591671] wlp3s0: associate with 84:61:a0:c8:68:e0 (try 1/3)
[302720.598338] wlp3s0: RX AssocResp from 84:61:a0:c8:68:e0 (capab=0x411 status=0 aid=5)
[302720.620523] wlp3s0: associated
[313891.092842] usb 2-1.2: USB disconnect, device number 5
[313891.093361] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[313891.292408] sd 6:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=0x07 driverbyte=0x00
[313891.525718] usb 2-1.2: new high-speed USB device number 6 using ehci-pci
[313891.682143] scsi host7: uas
[313891.683509] scsi 7:0:0:0: Direct-Access     Seagate  BUP BK           0304 PQ: 0 ANSI: 6
[313891.727014] sd 7:0:0:0: [sdc] 7814037167 512-byte logical blocks: (4.00 TB/3.64 TiB)
[313891.727018] sd 7:0:0:0: [sdc] 4096-byte physical blocks
[313891.792675] sd 7:0:0:0: [sdc] Write Protect is off
[313891.792685] sd 7:0:0:0: [sdc] Mode Sense: 4f 00 00 00
[313891.793418] sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[313891.958920]  sdc: sdc1
[313891.961891] sd 7:0:0:0: [sdc] Attached SCSI disk
[316293.063487] Aborting journal on device dm-1-8.
[316293.063530] Buffer I/O error on dev dm-1, logical block 488144896, lost sync page write
[316293.063543] JBD2: Error -5 detected when updating journal superblock for dm-1-8.
[318521.899135] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[318521.899177] EXT4-fs error (device dm-1): ext4_journal_check_start:56: Detected aborted journal
[318521.899190] EXT4-fs (dm-1): Remounting filesystem read-only
[318521.899201] EXT4-fs (dm-1): previous I/O error to superblock detected
[318521.899255] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[318551.853449] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #66584585: lblock 0: comm ranger: error -5 reading directory block
[318552.562096] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #62914561: lblock 0: comm ranger: error -5 reading directory blockown (SStatus 0 SControl 300)r: error -5 reading directory block
[318553.745497] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #66977793: lblock 0: comm ranger: error -5 reading directory block
[318553.746274] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #61865995: lblock 0: comm ranger: error -5 reading directory block
[318555.437637] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #68288513: lblock 0: comm ranger: error -5 reading directory block
[318555.438276] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #68157441: lblock 0: comm ranger: error -5 reading directory block
[318555.439291] EXT4-fs warning (device dm-1): htree_dirblock_to_tree:960: inode #61865985: lblock 0: comm ranger: error -5 reading directory block
[318577.974814] EXT4-fs (dm-1): previous I/O error to superblock detected
[318577.974852] Buffer I/O error on dev dm-1, logical block 0, lost sync page write
[318577.974858] EXT4-fs error (device dm-1): ext4_put_super:837: Couldn't clean up the journal
[318598.968517] usb 2-1.2: USB disconnect, device number 6
[318598.969422] sd 7:0:0:0: [sdc] Synchronizing SCSI cache
[318599.171132] sd 7:0:0:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x07 driverbyte=0x00
[318601.734599] usb 2-1.2: new high-speed USB device number 7 using ehci-pci
[318601.890782] scsi host6: uas
[318601.893088] scsi 6:0:0:0: Direct-Access     Seagate  BUP BK           0304 PQ: 0 ANSI: 6
[318601.939201] sd 6:0:0:0: [sdb] Spinning up disk...
[318602.954666] .....ready
[318607.008781] sd 6:0:0:0: [sdb] 7814037167 512-byte logical blocks: (4.00 TB/3.64 TiB)
[318607.008786] sd 6:0:0:0: [sdb] 2048-byte physical blocks
[318607.042153] sd 6:0:0:0: [sdb] Write Protect is off
[318607.042160] sd 6:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[318607.042891] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[318607.218483]  sdb: sdb1
[318607.222540] sd 6:0:0:0: [sdb] Attached SCSI disk
[318631.234528] device-mapper: table: 254:1: adding target device sdb1 caused an alignment inconsistency: physical_block_size=4096, logical_block_size=512, alignment_offset=0, start=33553920
[318631.234532] device-mapper: table: 254:1: adding target device sdb1 caused an alignment inconsistency: physical_block_size=4096, logical_block_size=512, alignment_offset=0, start=33553920
[318641.841636] EXT4-fs (dm-1): recovery complete
[318641.858727] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[321453.085391] PM: Syncing filesystems ... done.
[321453.919691] PM: Preparing system for sleep (mem)
[321453.920393] Freezing user space processes ... (elapsed 0.001 seconds) done.
[321453.922264] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds) 
[321453.922355] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[321453.923643] PM: Suspending system (mem)
[321453.923678] Suspending console(s) (use no_console_suspend to debug)
[321453.924032] sd 6:0:0:0: [sdb] Synchronizing SCSI cache
[321453.924260] wlp3s0: deauthenticating from 84:61:a0:c8:68:e0 by local choice (Reason: 3=DEAUTH_LEAVING)
[321454.092220] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[321453.924260] wlp3s0: deauthenticating from 84:61:a0:c8:68:e0 by local choice (Reason: 3=DEAUTH_LEAVING)
[321454.092220] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[321454.092480] sd 0:0:0:0: [sda] Stopping disk
[321454.329959] e1000e: EEE TX LPI TIMER: 00000011
[321454.686945] PM: suspend of devices complete after 762.904 msecs
[321454.703103] PM: late suspend of devices complete after 16.151 msecs
[321454.706274] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[321454.706465] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[321454.706605] e1000e 0000:00:19.0: System wakeup enabled by ACPI
[321454.723082] PM: noirq suspend of devices complete after 19.974 msecs
[321454.723470] ACPI: Preparing to enter system sleep state S3
[321455.023108] ACPI : EC: EC stopped
[321455.023110] PM: Saving platform NVS memory
[321455.023133] Disabling non-boot CPUs ...
[321455.047977] smpboot: CPU 1 is now offline
[321455.081889] smpboot: CPU 2 is now offline
[321455.111094] smpboot: CPU 3 is now offline
[321455.113228] ACPI: Low-level resume complete
[321455.113270] ACPI : EC: EC started
[321455.113271] PM: Restoring platform NVS memory
[321455.113609] Enabling non-boot CPUs ...
[321455.113648] x86: Booting SMP configuration:
[321455.113649] smpboot: Booting Node 0 Processor 1 APIC 0x1
[321455.113948] Disabled fast string operations
[321455.221612]  cache: parent cpu1 should not be sleeping
[321455.221957] CPU1 is up
[321455.222020] smpboot: Booting Node 0 Processor 2 APIC 0x2
[321455.222468] Disabled fast string operations
[321455.328286]  cache: parent cpu2 should not be sleeping
[321455.328688] CPU2 is up
[321455.328740] smpboot: Booting Node 0 Processor 3 APIC 0x3
[321455.329438] Disabled fast string operations
[321455.441623]  cache: parent cpu3 should not be sleeping
[321455.442048] CPU3 is up
[321455.447501] ACPI: Waking up from system sleep state S3
[321456.025382] sdhci-pci 0000:0d:00.0: MMC controller base frequency changed to 50Mhz.
[321456.025548] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[321456.025697] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[321456.032246] PM: noirq resume of devices complete after 27.353 msecs
[321456.032767] PM: early resume of devices complete after 0.486 msecs
[321456.034931] e1000e 0000:00:19.0: System wakeup disabled by ACPI
[321456.036290] rtc_cmos 00:02: System wakeup disabled by ACPI
[321456.036691] sd 0:0:0:0: [sda] Starting disk
[321456.038171] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[321456.038552] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[321456.038655] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[321456.064908] tpm tpm0: TPM is disabled/deactivated (0x6)
[321456.271579] usb 1-1.6: reset high-speed USB device number 5 using ehci-pci
[321456.314340] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[321456.314598] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[321456.314697] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[321456.377933] ata5: SATA link down (SStatus 0 SControl 300)
[321456.377967] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[321456.377999] ata4: SATA link down (SStatus 0 SControl 300)
[321456.444933] usb 1-1.4: reset full-speed USB device number 4 using ehci-pci
[321456.565506] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[321456.566322] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[321456.566326] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[321456.580820] ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 (IDLE) succeeded
[321456.581257] ata2.00: ACPI cmd e3/00:02:00:00:00:a0 (IDLE) succeeded
[321456.581261] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[321456.582935] ata2.00: configured for UDMA/100
[321456.614935] usb 1-1.3: reset full-speed USB device number 3 using ehci-pci
[321456.618247] firewire_core 0000:0d:00.3: rediscovered device fw0
[321456.712447] PM: resume of devices complete after 679.627 msecs
[321456.712564] usb 1-1.4:1.0: rebind failed: -517
[321456.712576] usb 1-1.4:1.1: rebind failed: -517
[321456.802956] psmouse serio1: synaptics: queried max coordinates: x [..5888], y [..4820]
[321456.836804] PM: Finishing wakeup.
[321456.836807] Restarting tasks ... done.
[321456.862677] video LNXVIDEO:00: Restoring backlight state
[321458.301704] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[321458.443545] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[321458.443551] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[321458.443555] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[321458.484354] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[321458.484357] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[321458.484358] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[321458.487994] ata1.00: configured for UDMA/133
[321459.975247] wlp3s0: authenticate with 84:61:a0:c8:68:e0
[321459.977178] wl[321459.981024] wlp3s0: authenticated
[321459.981796] wlp3s0: associate with 84:61:a0:c8:68:e0 (try 1/3)
[321459.987815] wlp3s0: RX AssocResp from 84:61:a0:c8:68:e0 (capab=0x411 status=0 aid=5)
[321460.012969] wlp3s0: associated

seth · 2017-01-07 01:54:35

try another usb slot and cable(! it's the cable)
and why is it subject to lvm? is it part of a raid cluster??

R00KIE · 2017-01-07 12:24:14

Doesn't surprise me much that you are seeing problems, you are suspending multiple times, at some points it even seems you unplug the device or for some reason it gets unplugged. When that happens, even if the device comes up on the same device node it usually results in errors.

When resuming from suspend the usb devices are reset and enumerated again and there is no guarantee that they will enumerate again in the same order or even be ready by the time the kernel wants to use them again or the devices may get unresponsive for some reason (maybe controller or firmware bugs).

The big question here is: does it work properly if you don't suspend your system? If it does then you can try to inquire upstream about this, maybe you have found a bug or something that needs improvement.

Arch Linux

#1 2017-01-07 00:49:03

external hard drive randomly disconnects

#2 2017-01-07 01:09:30

Re: external hard drive randomly disconnects

#3 2017-01-07 01:24:45

Re: external hard drive randomly disconnects

#4 2017-01-07 01:54:35

Re: external hard drive randomly disconnects

#5 2017-01-07 12:24:14

Re: external hard drive randomly disconnects

Board footer