You are not logged in.
When I change the input in either tvtime or xawtv the telvision audio is still the only one herd. I'm trying to use the S-Video input. The picture show up fine. I've tried unmuting and turning everything up in alsamixer. My guess is that v4l is not telling the tv-card to switch audio channels correctly. Any ideas on how to resolve this?
This info might be helpfull:
--From lspci--
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 02)
00:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 02)
00:0b.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
00:0d.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti 4200] (rev a3)
--From dmesg | grep bttv--
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 2) at 0000:00:09.0, irq: 20, latency: 32, mmio: 0xe6121000
bttv0: detected: ATI TV Wonder [card=63], PCI subsystem ID is 1002:0001
bttv0: using: ATI TV-Wonder [card=63,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv0: using tuner=19
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .<6>input: B16_b_02 USB-PS/2 Optical Mouse as /class/input/input2
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: timeout: drop=16 irq=34289/34289, risc=379fd764, bits: HSYNC OFLOW
bttv0: reset, reinitialize
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: timeout: drop=32 irq=38785/38785, risc=35b48834, bits: HSYNC OFLOW
bttv0: reset, reinitialize
bttv0: PLL can sleep, using XTAL (28636363).
Offline
FYI: Using the testing kernel 2.6.17rc6-1 seemed to fix it.
Offline