You are not logged in.
Pages: 1
I have a Targus 4-port USB hub that I use with my Averatec laptop. I've recently started having isisues with it on my laptop. During the boot process, I get the following output about it:
Jun 15 16:28:01 AVERATEC usb usb4: configuration #1 chosen from 1 choice
Jun 15 16:28:01 AVERATEC hub 4-0:1.0: USB hub found
Jun 15 16:28:01 AVERATEC hub 4-0:1.0: 2 ports detected
Jun 15 16:28:01 AVERATEC usb 1-3: new high speed USB device using ehci_hcd and address 3
Jun 15 16:28:01 AVERATEC ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
Jun 15 16:28:01 AVERATEC usb 1-3: device not accepting address 3, error -110
Jun 15 16:28:01 AVERATEC usb 1-3: new high speed USB device using ehci_hcd and address 4
Jun 15 16:28:01 AVERATEC usb 1-3: device not accepting address 4, error -110
Jun 15 16:28:01 AVERATEC usb 1-3: new high speed USB device using ehci_hcd and address 5
Jun 15 16:28:01 AVERATEC usb 1-3: device not accepting address 5, error -110
Jun 15 16:28:01 AVERATEC usb 1-3: new high speed USB device using ehci_hcd and address 6
Jun 15 16:28:01 AVERATEC usb 1-3: device not accepting address 6, error -110
Jun 15 16:28:01 AVERATEC usb 2-1: new low speed USB device using uhci_hcd and address 2
Jun 15 16:28:01 AVERATEC usb 2-1: configuration #1 chosen from 1 choice
Jun 15 16:28:01 AVERATEC usbcore: registered new driver usblp
Jun 15 16:28:01 AVERATEC drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Jun 15 16:28:01 AVERATEC Initializing USB Mass Storage driver...
Jun 15 16:28:01 AVERATEC usb 1-3: new high speed USB device using ehci_hcd and address 7
Jun 15 16:28:01 AVERATEC usb 1-3: device not accepting address 7, error -110
Jun 15 16:28:01 AVERATEC usb 1-3: new high speed USB device using ehci_hcd and address 8
Jun 15 16:28:01 AVERATEC usb 1-3: device not accepting address 8, error -110
Jun 15 16:28:01 AVERATEC usb 1-3: new high speed USB device using ehci_hcd and address 9
Jun 15 16:28:01 AVERATEC usb 1-3: device not accepting address 9, error -110
Jun 15 16:28:01 AVERATEC usb 1-3: new high speed USB device using ehci_hcd and address 10
Jun 15 16:28:01 AVERATEC usb 1-3: device not accepting address 10, error -110I am unable to access any devices plugged into the hub, including my HP printer which works fine when I plug it directly into a USB port on the computer, as well as my flash drive. I've tried the hub on another computer, and it works just fine. I'm using a custom kernel.
Bostoniman
Ba-zing Communications
Offline
I have the same problem trying to get my usb mp3 player (iriver ihp 120) mounted when I use the original firmware.
When using the rockbox firmware I get this problem trying to write on it:
FAT: Filesystem panic (dev sda1)
invalid access to FAT (entry 0x0025355a)
File system has been set read-only
edit: a "fsck -t vfat /mnt/sda1" solved the problem
As is true for most people I know, I've always loved learning. As is also true for most people I know, I always hated school. Why is that?
Offline
I may try that, but I don't think that this is a mounting issue, since it's a hub that simply allows other devices physical access, not a device with storage within itself. It sounds like the OS is having trouble allocating address space to the device. The problem is, I don't know enough about how the OS handles USB devices and address mapping to understand how to fix it.
Bostoniman
Ba-zing Communications
Offline
Pages: 1