You are not logged in.
I recently bought this notebook and installed ArchLinux. But I'm having problems with processor performance. It has a low clock (480Mhz) at rest but when it needs performance it takes time to switch to a higher clock rate, and when it does it reaches 1300Mhz or so.
I followed the steps of the Laptop-Mode wiki and the best I got was the result described above. (It was worse)
Something I discovered was when the following kernel message appears performance drops and does not return to normal:
CPU0: Core temperature above threshold, cpu clock throttled (total events = 1) The message above appears just after a few seconds of boot. I realized the diference performance because even dmesg output are affected.
Does anyone know how to solve this problem?
Environment information:
[root@compaq ~]# uname -a
Linux compaq 4.11.6-3-ARCH #1 SMP PREEMPT Thu Jun 22 12:21:46 CEST 2017 x86_64 GNU/Linux[root@compaq ~]# cat /etc/cpufreq-bench.conf
sleep = 50000
load = 50000
cpu = 0
priority = LOW
output = /var/log/cpufreq-bench
sleep_step = 50000
load_step = 50000
cycles = 20
rounds = 40
verbose = 0
governor = ondemand[root@compaq ~]# pstate-frequency -G -c
pstate-frequency version 3.7.2
pstate::CPU_DRIVER -> intel_pstate
pstate::CPU_GOVERNOR -> performance
pstate::TURBO -> 0 [ON]
pstate::CPU_MIN -> 19% [480000KHz]
pstate::CPU_MAX -> 100% [2480000KHz]
[root@compaq ~]# pstate-frequency -G -r
pstate-frequency version 3.7.2
pstate::CPU[0] -> 564.550MHz
pstate::CPU[1] -> 608.300MHz[root@compaq ~]# cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 76
model name : Intel(R) Celeron(R) CPU N3060 @ 1.60GHz
stepping : 4
microcode : 0x404
cpu MHz : 783.105
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 11
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology tsc_reliable nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes rdrand lahf_lm 3dnowprefetch epb tpr_shadow vnmi flexpriority ept vpid tsc_adjust smep erms dtherm ida arat
bugs :
bogomips : 3201.33
clflush size : 64
cache_alignment : 64
address sizes : 36 bits physical, 48 bits virtual
power management:
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 76
model name : Intel(R) Celeron(R) CPU N3060 @ 1.60GHz
stepping : 4
microcode : 0x404
cpu MHz : 1349.707
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 2
cpu cores : 2
apicid : 4
initial apicid : 4
fpu : yes
fpu_exception : yes
cpuid level : 11
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology tsc_reliable nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes rdrand lahf_lm 3dnowprefetch epb tpr_shadow vnmi flexpriority ept vpid tsc_adjust smep erms dtherm ida arat
bugs :
bogomips : 3204.69
clflush size : 64
cache_alignment : 64
address sizes : 36 bits physical, 48 bits virtual
power management:[root@compaq ~]# lsmod
Module Size Used by
nls_iso8859_1 16384 1
nls_cp437 20480 1
vfat 20480 1
fat 65536 1 vfat
btusb 40960 0
btrtl 16384 1 btusb
hid_sensor_accel_3d 16384 0
hid_sensor_trigger 16384 2 hid_sensor_accel_3d
hid_sensor_iio_common 16384 2 hid_sensor_accel_3d,hid_sensor_trigger
industrialio_triggered_buffer 16384 1 hid_sensor_accel_3d
kfifo_buf 16384 1 industrialio_triggered_buffer
industrialio 57344 4 hid_sensor_accel_3d,hid_sensor_trigger,industrialio_triggered_buffer,kfifo_buf
joydev 20480 0
mousedev 20480 0
arc4 16384 2
iwlmvm 286720 0
mac80211 696320 1 iwlmvm
intel_rapl 20480 0
intel_powerclamp 16384 0
coretemp 16384 0
kvm_intel 192512 0
kvm 528384 1 kvm_intel
irqbypass 16384 1 kvm
crct10dif_pclmul 16384 0
crc32_pclmul 16384 0
hid_sensor_hub 20480 3 hid_sensor_accel_3d,hid_sensor_iio_common,hid_sensor_trigger
crc32c_intel 24576 0
ghash_clmulni_intel 16384 0
pcbc 16384 0
iwlwifi 192512 1 iwlmvm
cfg80211 520192 3 iwlmvm,iwlwifi,mac80211
aesni_intel 163840 0
iTCO_wdt 16384 0
aes_x86_64 20480 1 aesni_intel
iTCO_vendor_support 16384 1 iTCO_wdt
crypto_simd 16384 1 aesni_intel
glue_helper 16384 1 aesni_intel
r8169 77824 0
rtsx_pci_ms 20480 0
memstick 16384 1 rtsx_pci_ms
cryptd 20480 3 crypto_simd,ghash_clmulni_intel,aesni_intel
evdev 24576 14
input_leds 16384 0
psmouse 126976 0
intel_cstate 16384 0
mac_hid 16384 0
mii 16384 1 r8169
pcspkr 16384 0
snd_hda_codec_hdmi 49152 1
intel_vbtn 16384 0
snd_hda_codec_realtek 73728 1
snd_hda_codec_generic 69632 1 snd_hda_codec_realtek
wmi 20480 0
battery 20480 0
sparse_keymap 16384 1 intel_vbtn
snd_soc_rt5670 118784 0
i2c_hid 20480 0
snd_soc_rl6231 16384 1 snd_soc_rt5670
i915 1433600 3
snd_intel_sst_acpi 16384 0
snd_intel_sst_core 69632 1 snd_intel_sst_acpi
snd_soc_sst_atom_hifi2_platform 86016 1 snd_intel_sst_core
snd_soc_sst_match 16384 1 snd_intel_sst_acpi
hci_uart 86016 0
snd_soc_core 192512 2 snd_soc_rt5670,snd_soc_sst_atom_hifi2_platform
snd_compress 20480 1 snd_soc_core
btbcm 16384 2 hci_uart,btusb
btqca 16384 1 hci_uart
btintel 16384 2 hci_uart,btusb
snd_pcm_dmaengine 16384 1 snd_soc_core
video 36864 1 i915
ac97_bus 16384 1 snd_soc_core
snd_hda_intel 36864 3
snd_hda_codec 106496 4 snd_hda_intel,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_codec_realtek
bluetooth 487424 7 btrtl,hci_uart,btintel,btqca,btbcm,btusb
i2c_designware_platform 16384 0
snd_hda_core 65536 5 snd_hda_intel,snd_hda_codec,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_codec_realtek
snd_hwdep 16384 1 snd_hda_codec
i2c_designware_core 20480 1 i2c_designware_platform
snd_pcm 90112 8 snd_hda_intel,snd_hda_codec,snd_soc_rt5670,snd_pcm_dmaengine,snd_hda_core,snd_soc_sst_atom_hifi2_platform,snd_hda_codec_hdmi,snd_soc_core
snd_timer 28672 1 snd_pcm
drm_kms_helper 126976 1 i915
snd 65536 17 snd_compress,snd_hda_intel,snd_hwdep,snd_hda_codec,snd_timer,snd_soc_sst_atom_hifi2_platform,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_codec_realtek,snd_soc_core,snd_pcm
drm 299008 4 i915,drm_kms_helper
rfkill_gpio 16384 0
rfkill 20480 6 rfkill_gpio,bluetooth,cfg80211
mei_txe 20480 0
mei 86016 1 mei_txe
ac 16384 0
shpchp 32768 0
8250_dw 16384 0
spi_pxa2xx_platform 24576 0
i2c_i801 24576 0
soc_button_array 16384 0
button 16384 1 i915
intel_gtt 20480 1 i915
soundcore 16384 1 snd
syscopyarea 16384 1 drm_kms_helper
sysfillrect 16384 1 drm_kms_helper
sysimgblt 16384 1 drm_kms_helper
fb_sys_fops 16384 1 drm_kms_helper
i2c_algo_bit 16384 1 i915
lpc_ich 24576 0
tpm_tis 16384 0
tpm_tis_core 20480 1 tpm_tis
tpm 40960 2 tpm_tis,tpm_tis_core
sch_fq_codel 20480 6
sg 36864 0
ip_tables 24576 0
x_tables 28672 1 ip_tables
ext4 528384 1
crc16 16384 2 bluetooth,ext4
jbd2 90112 1 ext4
fscrypto 24576 1 ext4
mbcache 16384 1 ext4
hid_multitouch 20480 0
hid_generic 16384 0
usbhid 45056 0
hid 110592 5 hid_sensor_hub,i2c_hid,hid_generic,usbhid,hid_multitouch
sd_mod 45056 4
rtsx_pci_sdmmc 24576 0
serio_raw 16384 0
atkbd 24576 0
libps2 16384 2 atkbd,psmouse
xhci_pci 16384 0
xhci_hcd 184320 1 xhci_pci
ahci 36864 3
rtsx_pci 49152 2 rtsx_pci_sdmmc,rtsx_pci_ms
libahci 28672 1 ahci
usbcore 208896 4 usbhid,xhci_pci,btusb,xhci_hcd
usb_common 16384 1 usbcore
libata 208896 2 ahci,libahci
scsi_mod 155648 3 sd_mod,libata,sg
i8042 24576 0
serio 20480 6 serio_raw,atkbd,psmouse,i8042
sdhci_acpi 16384 0
sdhci 40960 1 sdhci_acpi
led_class 16384 3 iwlmvm,sdhci,input_leds
mmc_core 122880 3 rtsx_pci_sdmmc,sdhci,sdhci_acpi[root@compaq ~]# cat /proc/cmdline
BOOT_IMAGE=/vmlinuz-linux root=UUID=20102afd-0a78-40c0-a633-bbf597f1335e rw text irqpool[root@compaq ~]# lspci -k
00:00.0 Host bridge: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series SoC Transaction Register (rev 35)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: iosf_mbi_pci
00:02.0 VGA compatible controller: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Integrated Graphics Controller (rev 35)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: i915
Kernel modules: i915
00:13.0 SATA controller: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series SATA Controller (rev 35)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: ahci
Kernel modules: ahci
00:14.0 USB controller: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series USB xHCI Controller (rev 35)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:1a.0 Encryption controller: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Trusted Execution Engine (rev 35)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: mei_txe
Kernel modules: mei_txe
00:1b.0 Audio device: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series High Definition Audio Controller (rev 35)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Express Port #1 (rev 35)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Express Port #2 (rev 35)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Express Port #3 (rev 35)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1f.0 ISA bridge: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCU (rev 35)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.3 SMBus: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx SMBus Controller (rev 35)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
02:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTL8411B PCI Express Card Reader (rev 01)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: rtsx_pci
Kernel modules: rtsx_pci
02:00.1 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 12)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device 2053
Kernel driver in use: r8169
Kernel modules: r8169
03:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83)
Subsystem: Intel Corporation Dual Band Wireless AC 3160
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi[root@compaq ~]# dmesg
[ 0.000000] Linux version 4.11.6-3-ARCH (builduser@anthraxx) (gcc version 7.1.1 20170516 (GCC) ) #1 SMP PREEMPT Thu Jun 22 12:21:46 CEST 2017
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=20102afd-0a78-40c0-a633-bbf597f1335e rw text irqpool
[ 0.000000] x86/fpu: x87 FPU will use FXSAVE
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000003efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000003f000-0x000000000003ffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x0000000000040000-0x000000000009dfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000076ce5fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000076ce6000-0x0000000076d5afff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000076d5b000-0x0000000076d6efff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x0000000076d6f000-0x0000000077699fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007769a000-0x0000000077966fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000077967000-0x00000000779bcfff] type 20
[ 0.000000] BIOS-e820: [mem 0x00000000779bd000-0x0000000077bb9fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000077bba000-0x0000000077ff6fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000077ff7000-0x0000000077ffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fea00000-0x00000000feafffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed03000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed06000-0x00000000fed06fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed09fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1cfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fedbffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.40 by American Megatrends
[ 0.000000] efi: ESRT=0x77963218 ACPI=0x76d5f000 ACPI 2.0=0x76d5f000 SMBIOS=0x778aed98
[ 0.000000] SMBIOS 2.8 present.
[ 0.000000] DMI: Compaq Compaq Presario CQ-360/Compaq Presario CQ-360, BIOS 1.00 08/22/2016
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x180000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07A800000 mask FFF800000 uncachable
[ 0.000000] 2 base 07B000000 mask FFF000000 uncachable
[ 0.000000] 3 base 07C000000 mask FFC000000 uncachable
[ 0.000000] 4 base 100000000 mask F80000000 write-back
[ 0.000000] 5 base 090000000 mask FF0000000 write-through
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] e820: last_pfn = 0x78000 max_arch_pfn = 0x400000000
[ 0.000000] esrt: Reserving ESRT space from 0x0000000077963218 to 0x0000000077963250.
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] BRK [0x02d42000, 0x02d42fff] PGTABLE
[ 0.000000] BRK [0x02d43000, 0x02d43fff] PGTABLE
[ 0.000000] BRK [0x02d44000, 0x02d44fff] PGTABLE
[ 0.000000] BRK [0x02d45000, 0x02d45fff] PGTABLE
[ 0.000000] BRK [0x02d46000, 0x02d46fff] PGTABLE
[ 0.000000] BRK [0x02d47000, 0x02d47fff] PGTABLE
[ 0.000000] Secure boot could not be determined
[ 0.000000] RAMDISK: [mem 0x372ab000-0x3794cfff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x0000000076D5F000 000024 (v02 HBW000)
[ 0.000000] ACPI: XSDT 0x0000000076D5F088 00008C (v01 HBW000 HBW00000 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x0000000076D6D210 00010C (v05 HBW000 HBW00000 01072009 AMI 00010013)
[ 0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/32 (20170119/tbfadt-603)
[ 0.000000] ACPI: DSDT 0x0000000076D5F1A0 00E06D (v02 HBW000 HBW00000 01072009 INTL 20120913)
[ 0.000000] ACPI: FACS 0x0000000077699E80 000040
[ 0.000000] ACPI: APIC 0x0000000076D6D320 000068 (v03 HBW000 HBW00000 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x0000000076D6D388 000044 (v01 HBW000 HBW00000 01072009 AMI 00010013)
[ 0.000000] ACPI: FIDT 0x0000000076D6D3D0 00009C (v01 HBW000 HBW00000 01072009 AMI 00010013)
[ 0.000000] ACPI: MSDM 0x0000000076D6D470 000055 (v03 HBW000 HBW00000 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x0000000076D6D4C8 00003C (v01 HBW000 HBW00000 01072009 MSFT 00000097)
[ 0.000000] ACPI: SSDT 0x0000000076D6D508 000763 (v01 PmRef CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x0000000076D6DC70 000290 (v01 PmRef Cpu0Tst 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x0000000076D6DF00 00017A (v01 PmRef ApTst 00003000 INTL 20061109)
[ 0.000000] ACPI: UEFI 0x0000000076D6E080 000042 (v01 HBW000 HBW00000 00000000 00000000)
[ 0.000000] ACPI: LPIT 0x0000000076D6E0C8 000104 (v01 HBW000 HBW00000 00000005 MSFT 0100000D)
[ 0.000000] ACPI: BGRT 0x0000000076D6E1D0 000038 (v01 HBW000 HBW00000 01072009 AMI 00010013)
[ 0.000000] ACPI: CSRT 0x0000000076D6E208 00014C (v00 INTEL LANFORDC 00000005 MSFT 0100000D)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000017fffffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x17fff7000-0x17fffbfff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000017fffffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000003efff]
[ 0.000000] node 0: [mem 0x0000000000040000-0x000000000009dfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000001fffffff]
[ 0.000000] node 0: [mem 0x0000000020200000-0x0000000076ce5fff]
[ 0.000000] node 0: [mem 0x00000000779bd000-0x0000000077bb9fff]
[ 0.000000] node 0: [mem 0x0000000077ff7000-0x0000000077ffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000017fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000017fffffff]
[ 0.000000] On node 0 totalpages: 1010824
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 22 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7540 pages used for memmap
[ 0.000000] DMA32 zone: 482540 pages, LIFO batch:31
[ 0.000000] Normal zone: 8192 pages used for memmap
[ 0.000000] Normal zone: 524288 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics memory at 0x000000007af00000-0x000000007eefffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-114
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0003f000-0x0003ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x76ce6000-0x76d5afff]
[ 0.000000] PM: Registered nosave memory: [mem 0x76d5b000-0x76d6efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x76d6f000-0x77699fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7769a000-0x77966fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x77967000-0x779bcfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x77bba000-0x77ff6fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x78000000-0x7aefffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7af00000-0x7eefffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7ef00000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfe9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfea00000-0xfeafffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed01fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed02000-0xfed02fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed03000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed05fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed06000-0xfed06fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed07000-0xfed07fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed08000-0xfed09fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed0a000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1cfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1d000-0xfed7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfedbffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfedc0000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffafffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xffb00000-0xffffffff]
[ 0.000000] e820: [mem 0x7ef00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] percpu: Embedded 35 pages/cpu @ffff88017fc00000 s103256 r8192 d31912 u1048576
[ 0.000000] pcpu-alloc: s103256 r8192 d31912 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 995006
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=20102afd-0a78-40c0-a633-bbf597f1335e rw text irqpool
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3862660K/4043296K available (6485K kernel code, 1091K rwdata, 2020K rodata, 1304K init, 904K bss, 180636K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=2
[ 0.000000] NR_IRQS:8448 nr_irqs:512 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.003333] tsc: Detected 1600.000 MHz processor
[ 0.003333] Calibrating delay loop (skipped), value calculated using timer frequency.. 3201.33 BogoMIPS (lpj=5333333)
[ 0.003333] pid_max: default: 32768 minimum: 301
[ 0.003333] ACPI: Core revision 20170119
[ 0.026265] ACPI: 4 ACPI AML tables successfully acquired and loaded
[ 0.026666] spurious 8259A interrupt: IRQ7.
[ 0.027516] Security Framework initialized
[ 0.027522] Yama: becoming mindful.
[ 0.027996] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.030281] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.031325] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.031337] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.031832] CPU: Physical Processor ID: 0
[ 0.031835] CPU: Processor Core ID: 0
[ 0.031841] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.031843] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.031854] mce: CPU supports 6 MCE banks
[ 0.031871] CPU0: Thermal monitoring enabled (TM1)
[ 0.031880] process: using mwait in idle threads
[ 0.031886] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[ 0.031888] Last level dTLB entries: 4KB 256, 2MB 16, 4MB 16, 1GB 0
[ 0.032211] Freeing SMP alternatives memory: 24K
[ 0.036039] ftrace: allocating 25552 entries in 100 pages
[ 0.050213] smpboot: Max logical packages: 1
[ 0.051341] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[ 0.084820] TSC deadline timer enabled
[ 0.084825] smpboot: CPU0: Intel(R) Celeron(R) CPU N3060 @ 1.60GHz (family: 0x6, model: 0x4c, stepping: 0x4)
[ 0.096688] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, 8-deep LBR, full-width counters, Intel PMU driver.
[ 0.096713] ... version: 3
[ 0.096716] ... bit width: 40
[ 0.096717] ... generic registers: 2
[ 0.096719] ... value mask: 000000ffffffffff
[ 0.096721] ... max period: 0000007fffffffff
[ 0.096722] ... fixed-purpose events: 3
[ 0.096723] ... event mask: 0000000700000003
[ 0.116832] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.123344] smp: Bringing up secondary CPUs ...
[ 0.150037] x86: Booting SMP configuration:
[ 0.150040] .... node #0, CPUs: #1
[ 0.233473] smp: Brought up 1 node, 2 CPUs
[ 0.233473] smpboot: Total of 2 processors activated (6405.02 BogoMIPS)
[ 0.233827] sched_clock: Marking stable (233333310, 0)->(241910738, -8577428)
[ 0.234815] devtmpfs: initialized
[ 0.234941] x86/mm: Memory block size: 128MB
[ 0.243656] PM: Registering ACPI NVS region [mem 0x0003f000-0x0003ffff] (4096 bytes)
[ 0.243661] PM: Registering ACPI NVS region [mem 0x76d6f000-0x77699fff] (9613312 bytes)
[ 0.244162] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.244175] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.244287] pinctrl core: initialized pinctrl subsystem
[ 0.244354] RTC time: 22:30:51, date: 06/30/17
[ 0.244622] NET: Registered protocol family 16
[ 0.245108] cpuidle: using governor ladder
[ 0.245123] cpuidle: using governor menu
[ 0.245127] PCCT header not found.
[ 0.245174] ACPI: bus type PCI registered
[ 0.245179] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.245330] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.245336] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.245372] PCI: Using configuration type 1 for base access
[ 0.247333] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.247941] ACPI: Added _OSI(Module Device)
[ 0.247943] ACPI: Added _OSI(Processor Device)
[ 0.247945] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.247947] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.486447] ACPI: Dynamic OEM Table Load:
[ 0.486463] ACPI: SSDT 0xFFFF88017A942800 0006B8 (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
[ 0.486992] ACPI: Dynamic OEM Table Load:
[ 0.487002] ACPI: SSDT 0xFFFF88017A9DE800 0003A5 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.487990] ACPI: Dynamic OEM Table Load:
[ 0.488000] ACPI: SSDT 0xFFFF88017A99F800 00015F (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.488456] ACPI: Dynamic OEM Table Load:
[ 0.488465] ACPI: SSDT 0xFFFF88017A99A6C0 00008D (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.490338] ACPI : EC: EC started
[ 0.490341] ACPI : EC: interrupt blocked
[ 0.490554] ACPI: \_SB_.PCI0.SBRG.EC0_: Used as first EC
[ 0.490559] ACPI: \_SB_.PCI0.SBRG.EC0_: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.490562] ACPI: \_SB_.PCI0.SBRG.EC0_: Used as boot DSDT EC to handle transactions
[ 0.490564] ACPI: Interpreter enabled
[ 0.490613] ACPI: (supports S0 S3 S4 S5)
[ 0.490616] ACPI: Using IOAPIC for interrupt routing
[ 0.490687] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.494737] ACPI: Power Resource [ID3C] (on)
[ 0.496876] ACPI: Power Resource [USBC] (on)
[ 0.509896] ACPI: Power Resource [CLK0] (off)
[ 0.510494] ACPI: Power Resource [CLK0] (off)
[ 0.510599] ACPI: Power Resource [CLK1] (off)
[ 0.745328] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.745343] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.745727] acpi PNP0A08:00: _OSC: platform does not support [PME]
[ 0.746092] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug AER PCIeCapability]
[ 0.747169] PCI host bridge to bus 0000:00
[ 0.747176] pci_bus 0000:00: root bus resource [io 0x0070-0x0077]
[ 0.747180] pci_bus 0000:00: root bus resource [io 0x0000-0x006f window]
[ 0.747183] pci_bus 0000:00: root bus resource [io 0x0078-0x0cf7 window]
[ 0.747187] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.747190] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.747193] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.747196] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff window]
[ 0.747199] pci_bus 0000:00: root bus resource [mem 0x80000000-0xdfffffff window]
[ 0.747204] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.747220] pci 0000:00:00.0: [8086:2280] type 00 class 0x060000
[ 0.747613] pci 0000:00:02.0: [8086:22b1] type 00 class 0x030000
[ 0.747640] pci 0000:00:02.0: reg 0x10: [mem 0x80000000-0x80ffffff 64bit]
[ 0.747656] pci 0000:00:02.0: reg 0x18: [mem 0x90000000-0x9fffffff 64bit pref]
[ 0.747667] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.747981] pci 0000:00:13.0: [8086:22a3] type 00 class 0x010601
[ 0.748033] pci 0000:00:13.0: reg 0x20: [io 0xf060-0xf07f]
[ 0.748044] pci 0000:00:13.0: reg 0x24: [mem 0x8141c000-0x8141c7ff]
[ 0.748102] pci 0000:00:13.0: PME# supported from D3hot
[ 0.748355] pci 0000:00:14.0: [8086:22b5] type 00 class 0x0c0330
[ 0.748379] pci 0000:00:14.0: reg 0x10: [mem 0x81400000-0x8140ffff 64bit]
[ 0.748462] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.748672] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.748767] pci 0000:00:1a.0: [8086:2298] type 00 class 0x108000
[ 0.748787] pci 0000:00:1a.0: reg 0x10: [mem 0x81100000-0x811fffff]
[ 0.748798] pci 0000:00:1a.0: reg 0x14: [mem 0x81000000-0x810fffff]
[ 0.748881] pci 0000:00:1a.0: PME# supported from D0 D3hot
[ 0.749197] pci 0000:00:1b.0: [8086:2284] type 00 class 0x040300
[ 0.749226] pci 0000:00:1b.0: reg 0x10: [mem 0x81410000-0x81413fff 64bit]
[ 0.749324] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.749511] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.749592] pci 0000:00:1c.0: [8086:22c8] type 01 class 0x060400
[ 0.749683] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.749862] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.749943] pci 0000:00:1c.1: [8086:22ca] type 01 class 0x060400
[ 0.750034] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.750216] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 0.750294] pci 0000:00:1c.2: [8086:22cc] type 01 class 0x060400
[ 0.750399] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.750580] pci 0000:00:1c.2: System wakeup disabled by ACPI
[ 0.750673] pci 0000:00:1f.0: [8086:229c] type 00 class 0x060100
[ 0.751020] pci 0000:00:1f.3: [8086:2292] type 00 class 0x0c0500
[ 0.751067] pci 0000:00:1f.3: reg 0x10: [mem 0x81418000-0x8141801f]
[ 0.751163] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.751611] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.751770] pci 0000:02:00.0: [10ec:5287] type 00 class 0xff0000
[ 0.751793] pci 0000:02:00.0: reg 0x10: [mem 0x81315000-0x81315fff]
[ 0.751846] pci 0000:02:00.0: reg 0x30: [mem 0x81300000-0x8130ffff pref]
[ 0.751954] pci 0000:02:00.0: supports D1 D2
[ 0.751957] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.752042] pci 0000:02:00.0: System wakeup disabled by ACPI
[ 0.752135] pci 0000:02:00.1: [10ec:8168] type 00 class 0x020000
[ 0.752160] pci 0000:02:00.1: reg 0x10: [io 0xe000-0xe0ff]
[ 0.752194] pci 0000:02:00.1: reg 0x18: [mem 0x81314000-0x81314fff 64bit]
[ 0.752215] pci 0000:02:00.1: reg 0x20: [mem 0x81310000-0x81313fff 64bit]
[ 0.752329] pci 0000:02:00.1: supports D1 D2
[ 0.752333] pci 0000:02:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.752412] pci 0000:02:00.1: System wakeup disabled by ACPI
[ 0.760446] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.760453] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
[ 0.760458] pci 0000:00:1c.1: bridge window [mem 0x81300000-0x813fffff]
[ 0.760600] pci 0000:03:00.0: [8086:08b3] type 00 class 0x028000
[ 0.760640] pci 0000:03:00.0: reg 0x10: [mem 0x81200000-0x81201fff 64bit]
[ 0.760831] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.760922] pci 0000:03:00.0: System wakeup disabled by ACPI
[ 0.770431] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.770439] pci 0000:00:1c.2: bridge window [mem 0x81200000-0x812fffff]
[ 0.774459] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.774619] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.774780] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.774942] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.775114] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.775271] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.775428] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.775595] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.894561] ACPI: Enabled 5 GPEs in block 00 to 3F
[ 0.894736] ACPI Warning: GPE type mismatch (level/edge) (20170119/evxface-826)
[ 0.894745] ACPI : EC: interrupt unblocked
[ 0.894755] ACPI : EC: event unblocked
[ 0.894766] ACPI: \_SB_.PCI0.SBRG.EC0_: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.894770] ACPI: \_SB_.PCI0.SBRG.EC0_: Used as boot DSDT EC to handle transactions and events
[ 0.927846] dw_dmac INTL9C60:01: DesignWare DMA Controller, 8 channels
[ 0.928174] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.928179] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.928188] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.928190] vgaarb: loaded
[ 0.928336] Registered efivars operations
[ 0.931607] PCI: Using ACPI for IRQ routing
[ 0.940539] PCI: pci_cache_line_size set to 64 bytes
[ 0.940616] e820: reserve RAM buffer [mem 0x0003f000-0x0003ffff]
[ 0.940619] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[ 0.940621] e820: reserve RAM buffer [mem 0x76ce6000-0x77ffffff]
[ 0.940624] e820: reserve RAM buffer [mem 0x77bba000-0x77ffffff]
[ 0.940831] NetLabel: Initializing
[ 0.940834] NetLabel: domain hash size = 128
[ 0.940835] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.940872] NetLabel: unlabeled traffic allowed by default
[ 0.941532] clocksource: Switched to clocksource refined-jiffies
[ 0.965972] VFS: Disk quotas dquot_6.6.0
[ 0.966021] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.966207] pnp: PnP ACPI init
[ 0.966337] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.967092] system 00:01: [io 0x0680-0x069f] has been reserved
[ 0.967097] system 00:01: [io 0x0400-0x047f] has been reserved
[ 0.967100] system 00:01: [io 0x0500-0x05fe] has been reserved
[ 0.967108] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.967205] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.967679] pnp 00:03: Plug and Play ACPI device, IDs SYN2902 SYN2900 SYN0002 PNP0f13 (active)
[ 0.969377] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.969529] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.969687] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.969853] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.970003] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.970157] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.970307] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.970460] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.970614] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.970757] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.970912] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.971096] system 00:0f: [mem 0x8141b000-0x8141bfff] has been reserved
[ 0.971104] system 00:0f: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.971285] system 00:10: [mem 0x81419000-0x81419fff] has been reserved
[ 0.971293] system 00:10: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.971448] system 00:11: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.971599] system 00:12: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.971751] system 00:13: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.971905] system 00:14: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.972053] system 00:15: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.972209] system 00:16: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.972324] system 00:17: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.972328] system 00:17: [mem 0xfea00000-0xfeafffff] has been reserved
[ 0.972332] system 00:17: [mem 0xfed01000-0xfed01fff] has been reserved
[ 0.972335] system 00:17: [mem 0xfed03000-0xfed03fff] has been reserved
[ 0.972340] system 00:17: [mem 0xfed06000-0xfed06fff] has been reserved
[ 0.972344] system 00:17: [mem 0xfed08000-0xfed09fff] has been reserved
[ 0.972348] system 00:17: [mem 0xfed80000-0xfedbffff] could not be reserved
[ 0.972351] system 00:17: [mem 0xfed1c000-0xfed1cfff] has been reserved
[ 0.972355] system 00:17: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.972362] system 00:17: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.083229] pnp: PnP ACPI: found 24 devices
[ 1.092352] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 1.092382] clocksource: Switched to clocksource acpi_pm
[ 1.092408] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 1.092414] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[ 1.092419] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000 add_align 100000
[ 1.092433] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[ 1.092462] pci 0000:00:1c.0: BAR 14: assigned [mem 0x81500000-0x816fffff]
[ 1.092475] pci 0000:00:1c.0: BAR 15: assigned [mem 0x81700000-0x818fffff 64bit pref]
[ 1.092485] pci 0000:00:1c.1: BAR 15: assigned [mem 0x81900000-0x81afffff 64bit pref]
[ 1.092493] pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 1.092499] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 1.092505] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
[ 1.092514] pci 0000:00:1c.0: bridge window [mem 0x81500000-0x816fffff]
[ 1.092519] pci 0000:00:1c.0: bridge window [mem 0x81700000-0x818fffff 64bit pref]
[ 1.092527] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 1.092531] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
[ 1.092537] pci 0000:00:1c.1: bridge window [mem 0x81300000-0x813fffff]
[ 1.092542] pci 0000:00:1c.1: bridge window [mem 0x81900000-0x81afffff 64bit pref]
[ 1.092550] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 1.092557] pci 0000:00:1c.2: bridge window [mem 0x81200000-0x812fffff]
[ 1.092567] pci_bus 0000:00: resource 4 [io 0x0070-0x0077]
[ 1.092571] pci_bus 0000:00: resource 5 [io 0x0000-0x006f window]
[ 1.092574] pci_bus 0000:00: resource 6 [io 0x0078-0x0cf7 window]
[ 1.092577] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 1.092580] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 1.092583] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 1.092586] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000fffff window]
[ 1.092589] pci_bus 0000:00: resource 11 [mem 0x80000000-0xdfffffff window]
[ 1.092593] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
[ 1.092596] pci_bus 0000:01: resource 1 [mem 0x81500000-0x816fffff]
[ 1.092599] pci_bus 0000:01: resource 2 [mem 0x81700000-0x818fffff 64bit pref]
[ 1.092603] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 1.092605] pci_bus 0000:02: resource 1 [mem 0x81300000-0x813fffff]
[ 1.092609] pci_bus 0000:02: resource 2 [mem 0x81900000-0x81afffff 64bit pref]
[ 1.092613] pci_bus 0000:03: resource 1 [mem 0x81200000-0x812fffff]
[ 1.092957] NET: Registered protocol family 2
[ 1.093448] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 1.093611] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 1.093804] TCP: Hash tables configured (established 32768 bind 32768)
[ 1.093906] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.093953] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.094104] NET: Registered protocol family 1
[ 1.094143] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 1.094676] PCI: CLS 64 bytes, default 64
[ 1.094796] Unpacking initramfs...
[ 1.278744] Freeing initrd memory: 6792K
[ 1.278769] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.278775] software IO TLB [mem 0x70e11000-0x74e11000] (64MB) mapped at [ffff880070e11000-ffff880074e10fff]
[ 1.278840] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x171024fa93b, max_idle_ns: 440795253189 ns
[ 1.278895] clocksource: Switched to clocksource tsc
[ 1.279070] Scanning for low memory corruption every 60 seconds
[ 1.280262] Initialise system trusted keyrings
[ 1.280358] workingset: timestamp_bits=40 max_order=20 bucket_order=0
[ 1.283454] zbud: loaded
[ 1.284828] Key type asymmetric registered
[ 1.284863] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.284929] io scheduler noop registered
[ 1.284931] io scheduler deadline registered
[ 1.285001] io scheduler cfq registered (default)
[ 1.285003] io scheduler mq-deadline registered
[ 1.286046] pciehp 0000:00:1c.0:pcie004: Slot #0 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ LLActRep+
[ 1.286140] pciehp 0000:00:1c.1:pcie004: Slot #1 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ LLActRep+
[ 1.286237] efifb: probing for efifb
[ 1.286264] efifb: framebuffer at 0x90000000, using 4160k, total 4160k
[ 1.286266] efifb: mode is 1366x768x32, linelength=5504, pages=1
[ 1.286267] efifb: scrolling: redraw
[ 1.286271] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.294611] Console: switching to colour frame buffer device 170x48
[ 1.302654] fb0: EFI VGA frame buffer device
[ 1.302672] intel_idle: MWAIT substates: 0x33000020
[ 1.302675] intel_idle: v0.4.1 model 0x4C
[ 1.302869] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.306034] GHES: HEST is not enabled!
[ 1.306219] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.326812] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 1.327440] Linux agpgart interface v0.103
[ 1.328087] rtc_cmos 00:00: RTC can wake from S4
[ 1.328268] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0
[ 1.328309] rtc_cmos 00:00: alarms up to one day, y3k, 242 bytes nvram
[ 1.328341] intel_pstate: Intel P-state driver initializing
[ 1.328788] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.330628] NET: Registered protocol family 10
[ 1.348632] Segment Routing with IPv6
[ 1.348695] NET: Registered protocol family 17
[ 1.349596] microcode: sig=0x406c4, pf=0x1, revision=0x404
[ 1.349727] microcode: Microcode Update Driver: v2.2.
[ 1.350272] registered taskstats version 1
[ 1.350303] Loading compiled-in X.509 certificates
[ 1.350379] zswap: loaded using pool lzo/zbud
[ 1.351964] Magic number: 5:69:554
[ 1.351991] pciehp 0000:00:1c.0:pcie004: hash matches
[ 1.352072] acpi PNP0C0F:05: hash matches
[ 1.352238] rtc_cmos 00:00: setting system clock to 2017-06-30 22:30:52 UTC (1498861852)
[ 1.352596] PM: Hibernation image not present or could not be loaded.
[ 1.359285] Freeing unused kernel memory: 1304K
[ 1.359294] Write protecting the kernel read-only data: 10240k
[ 1.361874] Freeing unused kernel memory: 1692K
[ 1.362439] Freeing unused kernel memory: 28K
[ 1.399722] random: systemd-tmpfile: uninitialized urandom read (16 bytes read)
[ 1.406005] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.406290] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.407601] random: udevadm: uninitialized urandom read (16 bytes read)
[ 1.407662] random: udevadm: uninitialized urandom read (16 bytes read)
[ 1.416571] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.416643] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.416677] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.417377] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.417457] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.488925] sdhci: Secure Digital Host Controller Interface driver
[ 1.489840] sdhci: Copyright(c) Pierre Ossman
[ 1.514273] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:SYN1] at 0x60,0x64 irq 1,12
[ 1.527086] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.527172] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.535569] SCSI subsystem initialized
[ 1.537992] libata version 3.00 loaded.
[ 1.540452] ACPI: bus type USB registered
[ 1.540493] usbcore: registered new interface driver usbfs
[ 1.540508] usbcore: registered new interface driver hub
[ 1.541603] ahci 0000:00:13.0: version 3.0
[ 1.541970] usbcore: registered new device driver usb
[ 1.541988] rtsx_pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 1.542249] rtsx_pci 0000:02:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 310
[ 1.552208] ahci 0000:00:13.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 1.552216] ahci 0000:00:13.0: flags: 64bit ncq ilck pm led clo only pio slum part deso sadm sds apst
[ 1.552953] scsi host0: ahci
[ 1.553130] scsi host1: ahci
[ 1.553212] ata1: SATA max UDMA/133 abar m2048@0x8141c000 port 0x8141c100 irq 309
[ 1.553215] ata2: SATA max UDMA/133 abar m2048@0x8141c000 port 0x8141c180 irq 309
[ 1.553854] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.553867] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 1.554994] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x01509810
[ 1.554999] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 1.555712] hub 1-0:1.0: USB hub found
[ 1.555817] hub 1-0:1.0: 7 ports detected
[ 1.557230] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.557245] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 1.557669] hub 2-0:1.0: USB hub found
[ 1.557696] hub 2-0:1.0: 6 ports detected
[ 1.558619] usb: port power management may be unreliable
[ 1.603940] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.869917] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.869986] ata2: SATA link down (SStatus 4 SControl 300)
[ 1.872057] ata1.00: ATA-10: WDC WD5000LPCX-22VHAT0, 01.01A01, max UDMA/133
[ 1.872071] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.874573] ata1.00: configured for UDMA/133
[ 1.875816] usb 1-1: new low-speed USB device number 2 using xhci_hcd
[ 1.875938] scsi 0:0:0:0: Direct-Access ATA WDC WD5000LPCX-2 1A01 PQ: 0 ANSI: 5
[ 1.922109] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 1.922113] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.922140] sd 0:0:0:0: [sda] Write Protect is off
[ 1.922143] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.922189] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.024875] sda: sda1 sda2 sda3
[ 2.026781] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.029221] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.034643] usbcore: registered new interface driver usbhid
[ 2.034646] usbhid: USB HID core driver
[ 2.035895] input: Dell Premium USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.0/0003:413C:3016.0001/input/input2
[ 2.035960] hid-generic 0003:413C:3016.0001: input,hidraw0: USB HID v1.11 Mouse [Dell Premium USB Optical Mouse] on usb-0000:00:14.0-1/input0
[ 2.132517] usb 1-4: new full-speed USB device number 3 using xhci_hcd
[ 2.280741] input: ELAN Touchscreen as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:228F.0002/input/input3
[ 2.280951] hid-multitouch 0003:04F3:228F.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [ELAN Touchscreen] on usb-0000:00:14.0-4/input0
[ 2.386046] usb 1-5: new full-speed USB device number 4 using xhci_hcd
[ 2.568878] random: fast init done
[ 2.636194] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 3.679552] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.790716] systemd[1]: systemd 232 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 3.790937] systemd[1]: Detected architecture x86-64.
[ 3.842112] systemd[1]: Set hostname to <compaq>.
[ 4.670748] random: crng init done
[ 4.960442] systemd[1]: Listening on Journal Socket.
[ 5.021197] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 5.021976] systemd[1]: Reached target Remote File Systems.
[ 5.025587] systemd[1]: Created slice User and Session Slice.
[ 5.026570] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.027294] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 5.027585] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 5.238760] EXT4-fs (sda3): re-mounted. Opts: data=ordered
[ 5.392916] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.473033] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input7
[ 7.473040] ACPI: Power Button [PWRB]
[ 7.473124] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input8
[ 7.473128] ACPI: Sleep Button [SLPB]
[ 7.500424] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[ 7.584600] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input9
[ 7.696291] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.771931] Bluetooth: Core ver 2.22
[ 7.771963] NET: Registered protocol family 31
[ 7.771965] Bluetooth: HCI device and connection manager initialized
[ 7.771970] Bluetooth: HCI socket layer initialized
[ 7.771974] Bluetooth: L2CAP socket layer initialized
[ 7.771982] Bluetooth: SCO socket layer initialized
[ 7.784852] systemd-journald[146]: Received request to flush runtime journal from PID 1
[ 7.806927] ACPI: Lid Switch [LID1]
[ 7.807122] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input10
[ 7.807131] ACPI: Power Button [PWRF]
[ 7.860977] Bluetooth: HCI UART driver ver 2.3
[ 7.860982] Bluetooth: HCI UART protocol H4 registered
[ 7.860983] Bluetooth: HCI UART protocol BCSP registered
[ 7.860984] Bluetooth: HCI UART protocol LL registered
[ 7.860985] Bluetooth: HCI UART protocol ATH3K registered
[ 7.860986] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 7.861053] Bluetooth: HCI UART protocol Intel registered
[ 7.861074] Bluetooth: HCI UART protocol Broadcom registered
[ 7.861075] Bluetooth: HCI UART protocol QCA registered
[ 7.861077] Bluetooth: HCI UART protocol AG6XX registered
[ 7.861078] Bluetooth: HCI UART protocol Marvell registered
[ 8.023002] ACPI: AC Adapter [AC0] (on-line)
[ 8.138285] [drm] Memory usable by graphics device = 2048M
[ 8.138290] checking generic (90000000 410000) vs hw (90000000 10000000)
[ 8.138292] fb: switching to inteldrmfb from EFI VGA
[ 8.138330] Console: switching to colour dummy device 80x25
[ 8.139203] [drm] Replacing VGA console driver
[ 8.139350] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 8.139352] [drm] Driver supports precise vblank timestamp query.
[ 8.159711] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 8.192544] [drm] Initialized i915 1.6.0 20170123 for 0000:00:02.0 on minor 0
[ 8.193812] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 8.194291] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input11
[ 8.309182] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[ 8.420405] fbcon: inteldrmfb (fb0) is primary device
[ 8.606008] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC269VC: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 8.606012] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.606014] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
[ 8.606015] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 8.606016] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 8.606019] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x19
[ 8.606021] snd_hda_codec_realtek hdaudioC0D0: Mic=0x18
[ 8.700980] ACPI: Battery Slot [BAT0] (battery present)
[ 8.701375] wmi: Mapper loaded
[ 9.029598] input: Intel Virtual Button driver as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D6:00/input/input15
[ 9.566644] input: PC Speaker as /devices/platform/pcspkr/input/input16
[ 9.570177] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 9.573441] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 9.573484] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[ 9.573526] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[ 10.071560] Console: switching to colour frame buffer device 170x48
[ 10.097502] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 10.886207] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 10.901465] r8169 0000:02:00.1 eth0: RTL8411 at 0xffffc900006f9000, 80:ee:73:c4:47:88, XID 1c800800 IRQ 315
[ 10.901470] r8169 0000:02:00.1 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 11.138616] psmouse serio1: synaptics: queried max coordinates: x [..5690], y [..4706]
[ 11.183834] psmouse serio1: synaptics: queried min coordinates: x [1300..], y [1234..]
[ 11.275982] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xf00123/0x840300/0x12e800/0x0, board id: 3003, fw id: 1738305
[ 11.336885] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input18
[ 11.918391] iTCO_vendor_support: vendor-support=0
[ 11.951483] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 11.951570] iTCO_wdt: Found a Braswell SoC TCO device (Version=3, TCOBASE=0x0460)
[ 11.951754] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 11.957927] SSE version of gcm_enc/dec engaged.
[ 12.135474] Intel(R) Wireless WiFi driver for Linux
[ 12.135478] Copyright(c) 2003- 2015 Intel Corporation
[ 12.135547] iwlwifi 0000:03:00.0: enabling device (0000 -> 0002)
[ 12.327912] i2c_hid i2c-ITE8350:00: error in i2c_hid_init_report size:19 / ret_size:18
[ 12.540020] asus_wmi: Asus Management GUID not found
[ 13.020764] intel_rapl: Found RAPL domain package
[ 13.020771] intel_rapl: Found RAPL domain core
[ 13.201907] iwlwifi 0000:03:00.0: loaded firmware version 17.459231.0 op_mode iwlmvm
[ 13.534090] iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 3160, REV=0x164
[ 13.536369] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 13.536621] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 13.780172] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[ 13.896783] Adding 4882428k swap on /dev/sda2. Priority:-1 extents:1 across:4882428k FS
[ 14.211827] mousedev: PS/2 mouse device common for all mice
[ 14.270124] r8169 0000:02:00.1 ens1f1: renamed from eth0
[ 14.298427] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0
[ 14.734899] usbcore: registered new interface driver btusb
[ 14.752816] Bluetooth: hci0: read Intel version: 370710010002030d00
[ 14.835703] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.0.2.3.d.bseq
[ 15.011808] Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
[ 16.080155] intel-vbtn INT33D6:00: unknown event index 0xcd
[ 18.110590] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 18.110829] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 18.241161] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 18.241404] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 18.254890] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[ 20.321755] r8169 0000:02:00.1 ens1f1: link down
[ 20.321764] r8169 0000:02:00.1 ens1f1: link down
[ 20.321859] IPv6: ADDRCONF(NETDEV_UP): ens1f1: link is not ready
[ 21.940445] r8169 0000:02:00.1 ens1f1: link up
[ 21.940463] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1: link becomes ready
[ 41.771638] CPU0: Core temperature above threshold, cpu clock throttled (total events = 1)
[ 1785.082261] midori[1263]: segfault at 5 ip 00007ff552d49602 sp 00007ffd667bb730 error 4 in libgobject-2.0.so.0.5200.2[7ff552d14000+51000]Last edited by tiagotarifa (2017-07-02 15:59:23)
Offline
Have you actually checked what the temperatures look like in BIOS and inside the OS (sensors-detect and sensors from the package lm_sensors)? Perhaps the CPU temperature sensor is being read incorrectly, which causes the clocks to be held back.
Offline
I checked for linux through the sensors command and the values were low. I ran the command now and the answer was this:
[ 18.892902] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 19.030933] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 19.031176] iwlwifi 0000:03:00.0: L1 Disabled - LTR Enabled
[ 19.044681] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[ 42.485893] CPU1: Core temperature above threshold, cpu clock throttled (total events = 1)
[root@compaq ~]# sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +39.0°C (high = +90.0°C, crit = +90.0°C)
Core 2: +39.0°C (high = +90.0°C, crit = +90.0°C)I added the dmesg output in the above lines. As you can see the problem happened.
The bios is very simple and does not show the temperature or a log on the error or alert events.
As I said in the first post and explaining better here, it seems that the kernel slows down because of the "warming up" but can not get back to normal.
Offline
Temperatures seem fine indeed. Not sure why it numbers the cores 0 and 2 instead of 0 and 1, but that is probably irrelevant to the issue at hand.
How are you verifying that it takes time for the clocks to rise and that around 1300 MHz seems to be the maximum? If it's done via cpufreq-bench I've sadly never used it. Could you check how
pstate-frequency -G -rbehaves while you run
stress -c 2? Also how exactly was it worse before you went trough the laptop-mode wiki page (https://wiki.archlinux.org/index.php/Laptop_Mode_Tools, correct?)?
Offline
How are you verifying that it takes time for the clocks to rise and that around 1300 MHz seems to be the maximum?
I checked through conky
Yes, it is!
Also how exactly was it worse before you went trough the laptop-mode wiki page?
The clock change was slower than now and the clock rarely up from 480mz
[root@compaq ~]# pstate-frequency -G -r
pstate-frequency version 3.7.2
pstate::CPU[0] -> 479.980MHz
pstate::CPU[1] -> 479.980MHz[root@compaq ~]# stress -c 2
stress: info: [3135] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd[root@compaq ~]# sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +45.0°C (high = +90.0°C, crit = +90.0°C)
Core 2: +45.0°C (high = +90.0°C, crit = +90.0°C)dmesg didn't change.
Offline
I'm not familiar with conky either, but it might be doing some averaging, which results in the change appearing to be slower than it actually is.
The order of your post makes it seem like you only checked the frequency before starting the stress test instead of monitoring it while the test was running. For example you can use
watch pstate-frequency -G -rto continuously poll for the frequency while stress is running in the background or in another terminal window.
i7zis also a good option for monitoring the frequency.
If you did indeed measure the frequency mentioned in your post while the stress test was ongoing, there really does seem to be a problem. Right now I'm just trying verify that the problem actually exists outside of the dmesg error entry too.
Offline
I'm not sure how but the problem stopped.
I did the following tests exactly in this sequence:
1. Remove (pacman -Rs) cpupower from Arch Linux and reboot (problem persist);
2. Disable cpufreq in laptop-mode-tools and reboot (problem persist);
3. Disable secure boot (EFI) on Bios and reboot (problem persist);
4. Disable audio, webcan, wireless, card reader, touch screen, lan card and virtualization on bios and reboot. <== Exactly here the problem has stopped occurring
The message in dmesg has stopped being displayed.
Programs, like firefox, have stopped slowing to open and load the menu.
From here I began to isolate the problem. I started activating what I had turned off one by one:
1. Enable wireless on bios and reboot;
2. Enable audio on bios and reboot;
3. Enable lan on bios and reboot;
4. Enable card reader on bios and reboot;
5. Enable touch on bios and reboot;
6. Enable webcan on bios and reboot;
7. Enable virtualization on bios and reboot;
And the problem did not occur anymore.
The notebook has the same settings before I start testing but the problem is no longer occurring. Only secure boot is still disabled.
It ran a youtube video in HD perfectly.
Now the processor clock hits 2.4Ghz in turbo bust.
Maybe a bios problem. I don't know.
It' a 1.0 version released in 08/22/2016.
The order of your post makes it seem like you only checked the frequency before starting the stress test instead of monitoring it while the test was running.
I started stress command first, than I ran "pstate-frequency -G -r"
Nassi, thank you very much for your help.
Offline
Good thing you managed to fix it. It does sound like the UEFI/BIOS was missbehaving. Remember to mark the thread as solved by editing the title.
Offline