You are not logged in.
- Topics: Active | Unanswered
#1 2017-08-11 23:42:51
- fishcop
- Member
- Registered: 2016-02-16
- Posts: 26
[Solved] Screen freezing problem with nvidia-driver
Hey guys,
as I want to program with Vulkan I recently switched from the nouveau driver to the propietary nvidia driver. After restarting i got just a frozen screen of the normal startup messages(nothing of any interest to find there). I got a GTX 965M and a new i7 Quad-core. The system is completely up to date, nvidia and nvidia-utils are installed, nouveau deinstalled. When I stop sddm(aka the running x-session) and start a new x-session, the TTY, from which I do this freezes as well and I have to switch to the next TTY. Doing a bit of research, I found out, that there may be a problem with the iGPU of my CPU and I should blacklist corresponding modules, so my /etc/modprobe.d/blacklist.conf look like that:
install i915 /usr/bin/false
install intel_agp /usr/bin/false
blacklist nvMy XOrg.conf was automatically created with
nvidia-xconfig.
The output of
lsmodshows no potential error source, as far as I know:
Module Size Used by
joydev 20480 0
mousedev 20480 0
nvidia_drm 45056 1
nvidia_modeset 835584 4 nvidia_drm
nls_iso8859_1 16384 1
nls_cp437 20480 1
vfat 20480 1
fat 65536 1 vfat
nvidia 12972032 78 nvidia_modeset
intel_rapl 20480 0
x86_pkg_temp_thermal 16384 0
intel_powerclamp 16384 0
coretemp 16384 0
kvm_intel 192512 0
arc4 16384 2
kvm 520192 1 kvm_intel
snd_hda_codec_hdmi 49152 1
snd_hda_codec_realtek 73728 1
irqbypass 16384 1 kvm
snd_hda_codec_generic 69632 1 snd_hda_codec_realtek
crct10dif_pclmul 16384 0
crc32_pclmul 16384 0
crc32c_intel 24576 0
ghash_clmulni_intel 16384 0
pcbc 16384 0
snd_hda_intel 36864 0
iwlmvm 294912 0
aesni_intel 167936 0
uvcvideo 86016 0
snd_hda_codec 106496 4 snd_hda_intel,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_codec_realtek
aes_x86_64 20480 1 aesni_intel
crypto_simd 16384 1 aesni_intel
snd_hda_core 65536 5 snd_hda_intel,snd_hda_codec,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_codec_realtek
glue_helper 16384 1 aesni_intel
btusb 40960 0
iTCO_wdt 16384 0
videobuf2_vmalloc 16384 1 uvcvideo
mac80211 688128 1 iwlmvm
cryptd 20480 3 crypto_simd,ghash_clmulni_intel,aesni_intel
hp_wmi 16384 0
sr_mod 24576 0
iTCO_vendor_support 16384 1 iTCO_wdt
videobuf2_memops 16384 1 videobuf2_vmalloc
snd_hwdep 16384 1 snd_hda_codec
btrtl 16384 1 btusb
sparse_keymap 16384 1 hp_wmi
cdrom 53248 1 sr_mod
r8168 499712 0
snd_pcm 86016 4 snd_hda_intel,snd_hda_codec,snd_hda_core,snd_hda_codec_hdmi
btbcm 16384 1 btusb
videobuf2_v4l2 20480 1 uvcvideo
intel_cstate 16384 0
btintel 16384 1 btusb
iwlwifi 208896 1 iwlmvm
intel_rapl_perf 16384 0
psmouse 131072 0
snd_timer 28672 1 snd_pcm
videobuf2_core 36864 2 uvcvideo,videobuf2_v4l2
bluetooth 475136 5 btrtl,btintel,btbcm,btusb
evdev 24576 4
pcspkr 16384 0
videodev 151552 3 uvcvideo,videobuf2_core,videobuf2_v4l2
input_leds 16384 0
cfg80211 520192 3 iwlmvm,iwlwifi,mac80211
mac_hid 16384 0
r8169 77824 0
drm_kms_helper 131072 1 nvidia_drm
media 32768 2 uvcvideo,videodev
rtsx_pci_ms 20480 0
snd 69632 8 snd_hda_intel,snd_hwdep,snd_hda_codec,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_codec_realtek,snd_pcm
ecdh_generic 24576 1 bluetooth
soundcore 16384 1 snd
uas 24576 0
rfkill 20480 6 bluetooth,hp_wmi,cfg80211
memstick 16384 1 rtsx_pci_ms
i2c_i801 24576 0
mii 16384 1 r8169
thermal 20480 0
battery 20480 0
drm 299008 4 nvidia_drm,drm_kms_helper
int3403_thermal 16384 0
intel_gtt 20480 0
syscopyarea 16384 1 drm_kms_helper
i2c_hid 20480 0
sysfillrect 16384 1 drm_kms_helper
sysimgblt 16384 1 drm_kms_helper
fb_sys_fops 16384 1 drm_kms_helper
hid 114688 1 i2c_hid
hp_accel 28672 0
i2c_algo_bit 16384 0
lis3lv02d 20480 1 hp_accel
input_polldev 16384 1 lis3lv02d
mei_me 36864 0
wmi 16384 1 hp_wmi
led_class 16384 3 iwlmvm,input_leds,hp_accel
processor_thermal_device 16384 0
intel_lpss_acpi 16384 0
mei 77824 1 mei_me
intel_lpss 16384 1 intel_lpss_acpi
video 36864 0
int340x_thermal_zone 16384 2 int3403_thermal,processor_thermal_device
tpm_crb 16384 0
shpchp 32768 0
intel_pch_thermal 16384 0
intel_soc_dts_iosf 16384 1 processor_thermal_device
tpm_tis 16384 0
tpm_tis_core 20480 1 tpm_tis
hp_wireless 16384 0
int3400_thermal 16384 0
tpm 49152 3 tpm_tis,tpm_crb,tpm_tis_core
acpi_thermal_rel 16384 1 int3400_thermal
ac 16384 0
acpi_pad 16384 0
button 16384 0
sch_fq_codel 20480 6
ip_tables 24576 0
x_tables 28672 1 ip_tables
ext4 540672 2
crc16 16384 2 bluetooth,ext4
jbd2 90112 1 ext4
fscrypto 24576 1 ext4
mbcache 16384 1 ext4
usb_storage 65536 1 uas
sd_mod 49152 5
rtsx_pci_sdmmc 24576 0
mmc_core 122880 1 rtsx_pci_sdmmc
serio_raw 16384 0
atkbd 24576 0
libps2 16384 2 atkbd,psmouse
ahci 36864 4
xhci_pci 16384 0
libahci 28672 1 ahci
xhci_hcd 188416 1 xhci_pci
libata 208896 2 ahci,libahci
rtsx_pci 49152 2 rtsx_pci_sdmmc,rtsx_pci_ms
usbcore 208896 6 uvcvideo,usb_storage,xhci_pci,btusb,uas,xhci_hcd
scsi_mod 155648 5 sd_mod,usb_storage,libata,uas,sr_mod
usb_common 16384 1 usbcore
i8042 24576 1 hp_accel
serio 20480 7 serio_raw,hp_accel,atkbd,psmouse,i8042Here the output of
dmesg:
[ 0.000000] microcode: microcode updated early to revision 0xba, date = 2017-04-09
[ 0.000000] Linux version 4.12.4-1-ARCH (builduser@nspawn-9860) (gcc version 7.1.1 20170630 (GCC) ) #1 SMP PREEMPT Fri Jul 28 18:54:18 UTC 2017
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ab03a09d-da68-4801-aeab-daef74de7086 rw quiet resume=/dev/sda4
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: xstate_offset[3]: 832, xstate_sizes[3]: 64
[ 0.000000] x86/fpu: xstate_offset[4]: 896, xstate_sizes[4]: 64
[ 0.000000] x86/fpu: Enabled xstate features 0x1f, context size is 960 bytes, using 'compacted' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000059000-0x0000000000085fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000086000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000063f9bfff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000063f9c000-0x0000000063f9cfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x0000000063f9d000-0x0000000063fe6fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000063fe7000-0x000000007a28dfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007a28e000-0x000000007a48dfff] type 20
[ 0.000000] BIOS-e820: [mem 0x000000007a48e000-0x000000007ac7dfff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007ac7e000-0x000000007ae7dfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007ae7e000-0x000000007aefdfff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000007aefe000-0x000000007aefefff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007aeff000-0x000000007fffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fd000000-0x00000000fe7fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed84000-0x00000000fed84fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffa00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000047effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.40 by INSYDE Corp.
[ 0.000000] efi: SMBIOS=0x7a4fb000 ESRT=0x7a4fe718 ACPI 2.0=0x7aefd014 PROP=0x62a1f238
[ 0.000000] SMBIOS 2.8 present.
[ 0.000000] DMI: HP OMEN by HP Laptop/8257, BIOS F.06 05/05/2016
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x47f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7800000000 write-back
[ 0.000000] 1 base 007AEFF000 mask 7FFFFFF000 uncachable
[ 0.000000] 2 base 007AF00000 mask 7FFFF00000 uncachable
[ 0.000000] 3 base 007B000000 mask 7FFF000000 uncachable
[ 0.000000] 4 base 007C000000 mask 7FFC000000 uncachable
[ 0.000000] 5 base 0080000000 mask 7F80000000 uncachable
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] e820: update [mem 0x7aeff000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0x7aeff max_arch_pfn = 0x400000000
[ 0.000000] esrt: Reserving ESRT space from 0x000000007a4fe718 to 0x000000007a4fe750.
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff8d260007c000] 7c000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] BRK [0x202d5f000, 0x202d5ffff] PGTABLE
[ 0.000000] BRK [0x202d60000, 0x202d60fff] PGTABLE
[ 0.000000] BRK [0x202d61000, 0x202d61fff] PGTABLE
[ 0.000000] BRK [0x202d62000, 0x202d62fff] PGTABLE
[ 0.000000] BRK [0x202d63000, 0x202d63fff] PGTABLE
[ 0.000000] BRK [0x202d64000, 0x202d64fff] PGTABLE
[ 0.000000] BRK [0x202d65000, 0x202d65fff] PGTABLE
[ 0.000000] BRK [0x202d66000, 0x202d66fff] PGTABLE
[ 0.000000] BRK [0x202d67000, 0x202d67fff] PGTABLE
[ 0.000000] Secure boot could not be determined
[ 0.000000] RAMDISK: [mem 0x370f5000-0x37871fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x000000007AEFD014 000024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 0x000000007AEDA188 000104 (v01 HPQOEM SLIC-MPC 00000000 HP 01000013)
[ 0.000000] ACPI: FACP 0x000000007AEDF000 0000F4 (v05 HPQOEM SLIC-MPC 00000000 HP 00040000)
[ 0.000000] ACPI: DSDT 0x000000007AEBC000 01D023 (v02 HPQOEM 8257 00000000 ACPI 00040000)
[ 0.000000] ACPI: FACS 0x000000007AE69000 000040
[ 0.000000] ACPI: TCPA 0x000000007AEFC000 000032 (v02 HPQOEM 8257 00000000 HP 00040000)
[ 0.000000] ACPI: UEFI 0x000000007AEFB000 000236 (v01 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: UEFI 0x000000007AEFA000 000042 (v01 HPQOEM 8257 00000002 HP 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEF9000 0004B7 (v02 HPQOEM 8257 00001000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEF8000 00004B (v02 HPQOEM 8257 00003000 ACPI 00040000)
[ 0.000000] ACPI: TPM2 0x000000007AEF7000 000034 (v03 HPQOEM 8257 00000000 HP 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEF0000 006E8D (v01 HPQOEM 8257 00001000 ACPI 00040000)
[ 0.000000] ACPI: MSDM 0x000000007AEEF000 000055 (v03 HPQOEM SLIC-MPC 00000001 HP 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEEA000 004E60 (v02 HPQOEM 8257 00003000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEE6000 00355B (v02 HPQOEM 8257 00001000 ACPI 00040000)
[ 0.000000] ACPI: DBGP 0x000000007AEE5000 000034 (v01 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: DBG2 0x000000007AEE4000 000054 (v00 HPQOEM 8257 00000000 HP 00040000)
[ 0.000000] ACPI: ASF! 0x000000007AEE3000 0000A5 (v32 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: ASPT 0x000000007AEE2000 000034 (v07 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: BOOT 0x000000007AEE1000 000028 (v01 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: DBGP 0x000000007AEE0000 000034 (v01 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: HPET 0x000000007AEDE000 000038 (v01 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: LPIT 0x000000007AEDD000 000094 (v01 HPQOEM 8257 00000000 HP 00040000)
[ 0.000000] ACPI: APIC 0x000000007AEDC000 0000BC (v03 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: MCFG 0x000000007AEDB000 00003C (v01 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEBB000 0002D4 (v01 HPQOEM 8257 00000000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEB8000 002BAE (v02 HPQOEM 8257 00001000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEB7000 000E73 (v02 HPQOEM 8257 00003000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000007AEB2000 004396 (v01 HPQOEM 8257 00001000 ACPI 00040000)
[ 0.000000] ACPI: DMAR 0x000000007AEB1000 0000A8 (v01 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: FPDT 0x000000007AEB0000 000044 (v01 HPQOEM SLIC-MPC 00000002 HP 00040000)
[ 0.000000] ACPI: BGRT 0x000000007AEAF000 000038 (v01 HPQOEM 8257 00000001 HP 00040000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000047effffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x47effb000-0x47effffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000047effffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x0000000000057fff]
[ 0.000000] node 0: [mem 0x0000000000059000-0x0000000000085fff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x0000000063f9bfff]
[ 0.000000] node 0: [mem 0x0000000063fe7000-0x000000007a28dfff]
[ 0.000000] node 0: [mem 0x000000007aefe000-0x000000007aefefff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000047effffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000047effffff]
[ 0.000000] On node 0 totalpages: 4166088
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 22 pages reserved
[ 0.000000] DMA zone: 3972 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7754 pages used for memmap
[ 0.000000] DMA32 zone: 496196 pages, LIFO batch:31
[ 0.000000] Normal zone: 57280 pages used for memmap
[ 0.000000] Normal zone: 3665920 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics memory at 0x000000007c000000-0x000000007fffffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00058000-0x00058fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00086000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x63f9c000-0x63f9cfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x63f9d000-0x63fe6fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7a28e000-0x7a48dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7a48e000-0x7ac7dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7ac7e000-0x7ae7dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7ae7e000-0x7aefdfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x7aeff000-0x7fffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x80000000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfcffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfd000000-0xfe7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe800000-0xfeafffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb04000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed83fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed84000-0xfed84fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed85000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xffa00000-0xffffffff]
[ 0.000000] e820: [mem 0x80000000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] percpu: Embedded 35 pages/cpu @ffff8d2a7ec00000 s106328 r8192 d28840 u262144
[ 0.000000] pcpu-alloc: s106328 r8192 d28840 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 4100968
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ab03a09d-da68-4801-aeab-daef74de7086 rw quiet resume=/dev/sda4
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 16258164K/16664352K available (6539K kernel code, 1124K rwdata, 2048K rodata, 1324K init, 912K bss, 406188K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] ftrace: allocating 27931 entries in 110 pages
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS:8448 nr_irqs:2048 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635855245 ns
[ 0.000000] hpet clockevent registered
[ 0.003333] tsc: Detected 2600.000 MHz processor
[ 0.003333] Calibrating delay loop (skipped), value calculated using timer frequency.. 5186.00 BogoMIPS (lpj=8640000)
[ 0.003333] pid_max: default: 32768 minimum: 301
[ 0.003333] ACPI: Core revision 20170303
[ 0.046017] ACPI: 10 ACPI AML tables successfully acquired and loaded
[ 0.046714] Security Framework initialized
[ 0.046716] Yama: becoming mindful.
[ 0.047516] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.051728] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.053185] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.053198] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.053487] CPU: Physical Processor ID: 0
[ 0.053488] CPU: Processor Core ID: 0
[ 0.053492] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.053493] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.053499] mce: CPU supports 10 MCE banks
[ 0.053509] CPU0: Thermal monitoring enabled (TM1)
[ 0.053531] process: using mwait in idle threads
[ 0.053533] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
[ 0.053534] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[ 0.053695] Freeing SMP alternatives memory: 24K
[ 0.057986] smpboot: Max logical packages: 2
[ 0.057997] DMAR: Host address width 39
[ 0.057998] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[ 0.058003] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 7e3ff0505e
[ 0.058005] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[ 0.058008] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da
[ 0.058009] DMAR: RMRR base: 0x0000007ab89000 end: 0x0000007aba8fff
[ 0.058010] DMAR: RMRR base: 0x0000007b800000 end: 0x0000007fffffff
[ 0.058012] DMAR-IR: IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 1
[ 0.058013] DMAR-IR: HPET id 0 under DRHD base 0xfed91000
[ 0.058014] DMAR-IR: x2apic is disabled because BIOS sets x2apic opt out bit.
[ 0.058015] DMAR-IR: Use 'intremap=no_x2apic_optout' to override the BIOS setting.
[ 0.059454] DMAR-IR: Enabled IRQ remapping in xapic mode
[ 0.059455] x2apic: IRQ remapping doesn't support X2APIC mode
[ 0.063333] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.093520] TSC deadline timer enabled
[ 0.093525] smpboot: CPU0: Intel(R) Core(TM) i7-6700HQ CPU @ 2.60GHz (family: 0x6, model: 0x5e, stepping: 0x3)
[ 0.106696] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver.
[ 0.106729] ... version: 4
[ 0.106730] ... bit width: 48
[ 0.106730] ... generic registers: 4
[ 0.106731] ... value mask: 0000ffffffffffff
[ 0.106731] ... max period: 00007fffffffffff
[ 0.106732] ... fixed-purpose events: 3
[ 0.106733] ... event mask: 000000070000000f
[ 0.126819] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.133338] smp: Bringing up secondary CPUs ...
[ 0.160035] x86: Booting SMP configuration:
[ 0.160036] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7
[ 0.903381] smp: Brought up 1 node, 8 CPUs
[ 0.903381] smpboot: Total of 8 processors activated (41501.38 BogoMIPS)
[ 0.906807] sched_clock: Marking stable (906666577, 0)->(1262467384, -355800807)
[ 0.907208] devtmpfs: initialized
[ 0.907251] x86/mm: Memory block size: 128MB
[ 0.911105] PM: Registering ACPI NVS region [mem 0x63f9c000-0x63f9cfff] (4096 bytes)
[ 0.911106] PM: Registering ACPI NVS region [mem 0x7ac7e000-0x7ae7dfff] (2097152 bytes)
[ 0.911186] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.911196] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.911258] pinctrl core: initialized pinctrl subsystem
[ 0.911365] RTC time: 22:36:59, date: 08/11/17
[ 0.911452] NET: Registered protocol family 16
[ 0.911636] cpuidle: using governor ladder
[ 0.911662] cpuidle: using governor menu
[ 0.911664] PCCT header not found.
[ 0.911711] Simple Boot Flag at 0x44 set to 0x1
[ 0.911733] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.911734] ACPI: bus type PCI registered
[ 0.911735] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.911817] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.911859] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.911863] pmd_set_huge: Cannot satisfy [mem 0xe0000000-0xe0200000] with a huge-page mapping due to MTRR override.
[ 0.912143] PCI: Using configuration type 1 for base access
[ 0.913212] HugeTLB registered 1 GB page size, pre-allocated 0 pages
[ 0.913213] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.913438] ACPI: Added _OSI(Module Device)
[ 0.913439] ACPI: Added _OSI(Processor Device)
[ 0.913440] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.913441] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.914653] ACPI: Executed 18 blocks of module-level executable AML code
[ 0.926428] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.931186] ACPI: Dynamic OEM Table Load:
[ 0.931258] ACPI: SSDT 0xFFFF8D2A6BE9B000 0005DC (v02 PmRef Cpu0Ist 00003000 INTL 20130117)
[ 0.931508] ACPI: \_PR_.CPU0: _OSC native thermal LVT Acked
[ 0.932915] ACPI: Dynamic OEM Table Load:
[ 0.932925] ACPI: SSDT 0xFFFF8D2A6BEC5800 00037F (v02 PmRef Cpu0Cst 00003001 INTL 20130117)
[ 0.933239] ACPI: Dynamic OEM Table Load:
[ 0.933247] ACPI: SSDT 0xFFFF8D2A6BE96E40 00008E (v02 PmRef Cpu0Hwp 00003000 INTL 20130117)
[ 0.933451] ACPI: Dynamic OEM Table Load:
[ 0.933458] ACPI: SSDT 0xFFFF8D2A6BECAE00 000130 (v02 PmRef HwpLvt 00003000 INTL 20130117)
[ 0.934401] ACPI: Dynamic OEM Table Load:
[ 0.934410] ACPI: SSDT 0xFFFF8D2A6BE9E800 0005AA (v02 PmRef ApIst 00003000 INTL 20130117)
[ 0.934934] ACPI: Dynamic OEM Table Load:
[ 0.934941] ACPI: SSDT 0xFFFF8D2A6BEC8C00 000119 (v02 PmRef ApHwp 00003000 INTL 20130117)
[ 0.935248] ACPI: Dynamic OEM Table Load:
[ 0.935256] ACPI: SSDT 0xFFFF8D2A6BEC9400 000119 (v02 PmRef ApCst 00003000 INTL 20130117)
[ 0.940740] ACPI : EC: EC started
[ 0.940741] ACPI : EC: interrupt blocked
[ 0.956868] ACPI Error: Needed type [Reference], found [Integer] ffff8d2a6bcf9ea0 (20170303/exresop-103)
[ 0.956876] ACPI Exception: AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable] (20170303/dswexec-461)
[ 0.956882] ACPI Error: Method parse/execution failed [\_SB.PCI0.LPCB.EC0.CPUS] (Node ffff8d2a6e145320), AE_AML_OPERAND_TYPE (20170303/psparse-543)
[ 0.956891] ACPI Error: Method parse/execution failed [\_SB.PCI0.LPCB.EC0.SASU] (Node ffff8d2a6e1455a0), AE_AML_OPERAND_TYPE (20170303/psparse-543)
[ 0.956898] ACPI Error: Method parse/execution failed [\_SB.PCI0.LPCB.EC0.ECMI] (Node ffff8d2a6e1456e0), AE_AML_OPERAND_TYPE (20170303/psparse-543)
[ 0.956905] ACPI Error: Method parse/execution failed [\_SB.PCI0.LPCB.EC0._REG] (Node ffff8d2a6e145168), AE_AML_OPERAND_TYPE (20170303/psparse-543)
[ 0.956916] ACPI: \_SB_.PCI0.LPCB.EC0_: Used as first EC
[ 0.956917] ACPI: \_SB_.PCI0.LPCB.EC0_: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.956918] ACPI: \_SB_.PCI0.LPCB.EC0_: Used as boot DSDT EC to handle transactions
[ 0.956919] ACPI: Interpreter enabled
[ 0.956978] ACPI: (supports S0 S3 S4 S5)
[ 0.956979] ACPI: Using IOAPIC for interrupt routing
[ 0.957024] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.958404] ACPI: Power Resource [PG00] (on)
[ 0.992390] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[ 0.992396] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.995749] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.995750] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
[ 0.998147] PCI host bridge to bus 0000:00
[ 0.998149] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.998150] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.998152] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.998153] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff window]
[ 0.998154] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff window]
[ 0.998155] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff window]
[ 0.998156] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff window]
[ 0.998157] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[ 0.998158] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[ 0.998159] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[ 0.998160] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[ 0.998161] pci_bus 0000:00: root bus resource [mem 0x80000000-0xdfffffff window]
[ 0.998162] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfe7fffff window]
[ 0.998163] pci_bus 0000:00: root bus resource [bus 00-fe]
[ 0.998171] pci 0000:00:00.0: [8086:1910] type 00 class 0x060000
[ 0.999202] pci 0000:00:01.0: [8086:1901] type 01 class 0x060400
[ 0.999247] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 1.000280] pci 0000:00:02.0: [8086:191b] type 00 class 0x030000
[ 1.000290] pci 0000:00:02.0: reg 0x10: [mem 0xa2000000-0xa2ffffff 64bit]
[ 1.000297] pci 0000:00:02.0: reg 0x18: [mem 0xb0000000-0xbfffffff 64bit pref]
[ 1.000301] pci 0000:00:02.0: reg 0x20: [io 0x5000-0x503f]
[ 1.001346] pci 0000:00:04.0: [8086:1903] type 00 class 0x118000
[ 1.001358] pci 0000:00:04.0: reg 0x10: [mem 0xa4420000-0xa4427fff 64bit]
[ 1.002474] pci 0000:00:14.0: [8086:a12f] type 00 class 0x0c0330
[ 1.002494] pci 0000:00:14.0: reg 0x10: [mem 0xa4400000-0xa440ffff 64bit]
[ 1.002568] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 1.003595] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 1.003628] pci 0000:00:14.2: [8086:a131] type 00 class 0x118000
[ 1.003648] pci 0000:00:14.2: reg 0x10: [mem 0xa4432000-0xa4432fff 64bit]
[ 1.004729] pci 0000:00:16.0: [8086:a13a] type 00 class 0x078000
[ 1.004751] pci 0000:00:16.0: reg 0x10: [mem 0xa4433000-0xa4433fff 64bit]
[ 1.004831] pci 0000:00:16.0: PME# supported from D3hot
[ 1.005884] pci 0000:00:17.0: [8086:a103] type 00 class 0x010601
[ 1.005900] pci 0000:00:17.0: reg 0x10: [mem 0xa4430000-0xa4431fff]
[ 1.005908] pci 0000:00:17.0: reg 0x14: [mem 0xa4436000-0xa44360ff]
[ 1.005916] pci 0000:00:17.0: reg 0x18: [io 0x5080-0x5087]
[ 1.005923] pci 0000:00:17.0: reg 0x1c: [io 0x5088-0x508b]
[ 1.005931] pci 0000:00:17.0: reg 0x20: [io 0x5060-0x507f]
[ 1.005939] pci 0000:00:17.0: reg 0x24: [mem 0xa4434000-0xa44347ff]
[ 1.005984] pci 0000:00:17.0: PME# supported from D3hot
[ 1.007037] pci 0000:00:1c.0: [8086:a114] type 01 class 0x060400
[ 1.007110] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.008148] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 1.008191] pci 0000:00:1c.5: [8086:a115] type 01 class 0x060400
[ 1.008265] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 1.009307] pci 0000:00:1c.5: System wakeup disabled by ACPI
[ 1.009338] pci 0000:00:1c.6: [8086:a116] type 01 class 0x060400
[ 1.009413] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[ 1.010462] pci 0000:00:1c.6: System wakeup disabled by ACPI
[ 1.010500] pci 0000:00:1f.0: [8086:a14e] type 00 class 0x060100
[ 1.011642] pci 0000:00:1f.2: [8086:a121] type 00 class 0x058000
[ 1.011655] pci 0000:00:1f.2: reg 0x10: [mem 0xa442c000-0xa442ffff]
[ 1.012747] pci 0000:00:1f.3: [8086:a170] type 00 class 0x040300
[ 1.012772] pci 0000:00:1f.3: reg 0x10: [mem 0xa4428000-0xa442bfff 64bit]
[ 1.012807] pci 0000:00:1f.3: reg 0x20: [mem 0xa4410000-0xa441ffff 64bit]
[ 1.012862] pci 0000:00:1f.3: PME# supported from D3hot D3cold
[ 1.013922] pci 0000:00:1f.3: System wakeup disabled by ACPI
[ 1.013957] pci 0000:00:1f.4: [8086:a123] type 00 class 0x0c0500
[ 1.014005] pci 0000:00:1f.4: reg 0x10: [mem 0xa4435000-0xa44350ff 64bit]
[ 1.014076] pci 0000:00:1f.4: reg 0x20: [io 0x5040-0x505f]
[ 1.015219] pci 0000:01:00.0: [10de:1427] type 00 class 0x030200
[ 1.015232] pci 0000:01:00.0: reg 0x10: [mem 0xa3000000-0xa3ffffff]
[ 1.015240] pci 0000:01:00.0: reg 0x14: [mem 0x90000000-0x9fffffff 64bit pref]
[ 1.015249] pci 0000:01:00.0: reg 0x1c: [mem 0xa0000000-0xa1ffffff 64bit pref]
[ 1.015254] pci 0000:01:00.0: reg 0x24: [io 0x4000-0x407f]
[ 1.015260] pci 0000:01:00.0: reg 0x30: [mem 0xfff80000-0xffffffff pref]
[ 1.015338] pci 0000:01:00.0: System wakeup disabled by ACPI
[ 1.023510] pci 0000:00:01.0: PCI bridge to [bus 01-06]
[ 1.023512] pci 0000:00:01.0: bridge window [io 0x4000-0x4fff]
[ 1.023515] pci 0000:00:01.0: bridge window [mem 0xa3000000-0xa40fffff]
[ 1.023518] pci 0000:00:01.0: bridge window [mem 0x90000000-0xa1ffffff 64bit pref]
[ 1.023623] pci 0000:07:00.0: [10ec:522a] type 00 class 0xff0000
[ 1.023648] pci 0000:07:00.0: reg 0x10: [mem 0xa4300000-0xa4300fff]
[ 1.023786] pci 0000:07:00.0: supports D1 D2
[ 1.023787] pci 0000:07:00.0: PME# supported from D1 D2 D3hot D3cold
[ 1.023882] pci 0000:07:00.0: System wakeup disabled by ACPI
[ 1.033573] pci 0000:00:1c.0: PCI bridge to [bus 07]
[ 1.033578] pci 0000:00:1c.0: bridge window [mem 0xa4300000-0xa43fffff]
[ 1.033791] pci 0000:08:00.0: [8086:095a] type 00 class 0x028000
[ 1.033883] pci 0000:08:00.0: reg 0x10: [mem 0xa4200000-0xa4201fff 64bit]
[ 1.034266] pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
[ 1.034473] pci 0000:08:00.0: System wakeup disabled by ACPI
[ 1.043681] pci 0000:00:1c.5: PCI bridge to [bus 08]
[ 1.043686] pci 0000:00:1c.5: bridge window [mem 0xa4200000-0xa42fffff]
[ 1.043751] pci 0000:09:00.0: [10ec:8168] type 00 class 0x020000
[ 1.043776] pci 0000:09:00.0: reg 0x10: [io 0x3000-0x30ff]
[ 1.043804] pci 0000:09:00.0: reg 0x18: [mem 0xa4104000-0xa4104fff 64bit]
[ 1.043821] pci 0000:09:00.0: reg 0x20: [mem 0xa4100000-0xa4103fff 64bit]
[ 1.043919] pci 0000:09:00.0: supports D1 D2
[ 1.043920] pci 0000:09:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.044021] pci 0000:09:00.0: System wakeup disabled by ACPI
[ 1.053537] pci 0000:00:1c.6: PCI bridge to [bus 09]
[ 1.053540] pci 0000:00:1c.6: bridge window [io 0x3000-0x3fff]
[ 1.053543] pci 0000:00:1c.6: bridge window [mem 0xa4100000-0xa41fffff]
[ 1.056349] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.056401] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 1.056450] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.056500] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.056548] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.056597] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.056645] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.056693] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.056992] platform MSFT0101:00: failed to claim resource 1: [mem 0xfed40000-0xfed40fff]
[ 1.056998] acpi MSFT0101:00: platform device creation failed: -16
[ 1.057233] ACPI: Enabled 7 GPEs in block 00 to 7F
[ 1.057435] ACPI : EC: interrupt unblocked
[ 1.057448] ACPI : EC: event unblocked
[ 1.057460] ACPI: \_SB_.PCI0.LPCB.EC0_: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 1.057462] ACPI: \_SB_.PCI0.LPCB.EC0_: Used as boot DSDT EC to handle transactions and events
[ 1.057534] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 1.057536] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 1.057540] pci 0000:00:02.0: vgaarb: bridge control possible
[ 1.057540] vgaarb: loaded
[ 1.057571] EDAC MC: Ver: 3.0.0
[ 1.057856] Registered efivars operations
[ 1.105936] PCI: Using ACPI for IRQ routing
[ 1.134016] PCI: pci_cache_line_size set to 64 bytes
[ 1.134450] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
[ 1.134451] e820: reserve RAM buffer [mem 0x00086000-0x0008ffff]
[ 1.134452] e820: reserve RAM buffer [mem 0x63f9c000-0x63ffffff]
[ 1.134453] e820: reserve RAM buffer [mem 0x7a28e000-0x7bffffff]
[ 1.134454] e820: reserve RAM buffer [mem 0x7aeff000-0x7bffffff]
[ 1.134455] e820: reserve RAM buffer [mem 0x47f000000-0x47fffffff]
[ 1.134539] NetLabel: Initializing
[ 1.134539] NetLabel: domain hash size = 128
[ 1.134540] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 1.134554] NetLabel: unlabeled traffic allowed by default
[ 1.134948] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 1.134954] hpet0: 8 comparators, 64-bit 24.000000 MHz counter
[ 1.137012] clocksource: Switched to clocksource hpet
[ 1.145500] VFS: Disk quotas dquot_6.6.0
[ 1.145517] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.145584] pnp: PnP ACPI init
[ 1.146428] system 00:00: [mem 0xfd000000-0xfdabffff] has been reserved
[ 1.146430] system 00:00: [mem 0xfdad0000-0xfdadffff] has been reserved
[ 1.146431] system 00:00: [mem 0xfdb00000-0xfdffffff] has been reserved
[ 1.146432] system 00:00: [mem 0xfe000000-0xfe01ffff] has been reserved
[ 1.146433] system 00:00: [mem 0xfe036000-0xfe03bfff] has been reserved
[ 1.146435] system 00:00: [mem 0xfe03d000-0xfe3fffff] has been reserved
[ 1.146436] system 00:00: [mem 0xfe410000-0xfe7fffff] has been reserved
[ 1.146439] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.146805] system 00:01: [io 0x2000-0x20fe] has been reserved
[ 1.146807] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.147057] system 00:02: [io 0x0680-0x069f] has been reserved
[ 1.147059] system 00:02: [io 0xffff] has been reserved
[ 1.147060] system 00:02: [io 0xffff] has been reserved
[ 1.147061] system 00:02: [io 0xffff] has been reserved
[ 1.147062] system 00:02: [io 0x1800-0x18fe] has been reserved
[ 1.147063] system 00:02: [io 0x164e-0x164f] has been reserved
[ 1.147065] system 00:02: [io 0x0454-0x0457] has been reserved
[ 1.147067] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.147171] system 00:03: [io 0x0800-0x087f] has been reserved
[ 1.147172] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.147192] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.147221] pnp 00:05: Plug and Play ACPI device, IDs HPQ8001 PNP0303 (active)
[ 1.147245] pnp 00:06: Plug and Play ACPI device, IDs SYN3239 SYN1e00 SYN0002 PNP0f13 (active)
[ 1.148842] system 00:07: [mem 0xfdaf0000-0xfdafffff] has been reserved
[ 1.148843] system 00:07: [mem 0xfdae0000-0xfdaeffff] has been reserved
[ 1.148845] system 00:07: [mem 0xfdac0000-0xfdacffff] has been reserved
[ 1.148847] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.149432] system 00:08: [mem 0xfed10000-0xfed17fff] has been reserved
[ 1.149433] system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
[ 1.149435] system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
[ 1.149436] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved
[ 1.149437] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 1.149440] system 00:08: [mem 0xfed90000-0xfed93fff] could not be reserved
[ 1.149441] system 00:08: [mem 0xfed45000-0xfed8ffff] could not be reserved
[ 1.149442] system 00:08: [mem 0xff000000-0xffffffff] could not be reserved
[ 1.149444] system 00:08: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 1.149445] system 00:08: [mem 0x80000000-0x8001ffff] has been reserved
[ 1.149447] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.150251] pnp: PnP ACPI: found 9 devices
[ 1.158190] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 1.158194] pci 0000:01:00.0: can't claim BAR 6 [mem 0xfff80000-0xffffffff pref]: no compatible bridge window
[ 1.158208] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 07] add_size 1000
[ 1.158210] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 07] add_size 200000 add_align 100000
[ 1.158234] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80100000-0x802fffff 64bit pref]
[ 1.158236] pci 0000:00:1c.0: BAR 13: assigned [io 0x6000-0x6fff]
[ 1.158239] pci 0000:01:00.0: BAR 6: assigned [mem 0xa4000000-0xa407ffff pref]
[ 1.158240] pci 0000:00:01.0: PCI bridge to [bus 01-06]
[ 1.158242] pci 0000:00:01.0: bridge window [io 0x4000-0x4fff]
[ 1.158245] pci 0000:00:01.0: bridge window [mem 0xa3000000-0xa40fffff]
[ 1.158247] pci 0000:00:01.0: bridge window [mem 0x90000000-0xa1ffffff 64bit pref]
[ 1.158251] pci 0000:00:1c.0: PCI bridge to [bus 07]
[ 1.158253] pci 0000:00:1c.0: bridge window [io 0x6000-0x6fff]
[ 1.158256] pci 0000:00:1c.0: bridge window [mem 0xa4300000-0xa43fffff]
[ 1.158259] pci 0000:00:1c.0: bridge window [mem 0x80100000-0x802fffff 64bit pref]
[ 1.158264] pci 0000:00:1c.5: PCI bridge to [bus 08]
[ 1.158267] pci 0000:00:1c.5: bridge window [mem 0xa4200000-0xa42fffff]
[ 1.158274] pci 0000:00:1c.6: PCI bridge to [bus 09]
[ 1.158276] pci 0000:00:1c.6: bridge window [io 0x3000-0x3fff]
[ 1.158279] pci 0000:00:1c.6: bridge window [mem 0xa4100000-0xa41fffff]
[ 1.158286] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 1.158287] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 1.158289] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 1.158290] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff window]
[ 1.158291] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff window]
[ 1.158292] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff window]
[ 1.158293] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff window]
[ 1.158294] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff window]
[ 1.158295] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff window]
[ 1.158296] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff window]
[ 1.158297] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff window]
[ 1.158298] pci_bus 0000:00: resource 15 [mem 0x80000000-0xdfffffff window]
[ 1.158299] pci_bus 0000:00: resource 16 [mem 0xfd000000-0xfe7fffff window]
[ 1.158300] pci_bus 0000:01: resource 0 [io 0x4000-0x4fff]
[ 1.158301] pci_bus 0000:01: resource 1 [mem 0xa3000000-0xa40fffff]
[ 1.158302] pci_bus 0000:01: resource 2 [mem 0x90000000-0xa1ffffff 64bit pref]
[ 1.158304] pci_bus 0000:07: resource 0 [io 0x6000-0x6fff]
[ 1.158305] pci_bus 0000:07: resource 1 [mem 0xa4300000-0xa43fffff]
[ 1.158306] pci_bus 0000:07: resource 2 [mem 0x80100000-0x802fffff 64bit pref]
[ 1.158307] pci_bus 0000:08: resource 1 [mem 0xa4200000-0xa42fffff]
[ 1.158308] pci_bus 0000:09: resource 0 [io 0x3000-0x3fff]
[ 1.158309] pci_bus 0000:09: resource 1 [mem 0xa4100000-0xa41fffff]
[ 1.158455] NET: Registered protocol family 2
[ 1.158615] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.158810] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.158917] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.158948] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.158998] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.159062] NET: Registered protocol family 1
[ 1.159076] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 1.160999] PCI: CLS 64 bytes, default 64
[ 1.161037] Unpacking initramfs...
[ 1.276686] Freeing initrd memory: 7668K
[ 1.276725] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.276728] software IO TLB [mem 0x75d19000-0x79d19000] (64MB) mapped at [ffff8d2675d19000-ffff8d2679d18fff]
[ 1.277045] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x255cb6cc5db, max_idle_ns: 440795203504 ns
[ 1.277285] Scanning for low memory corruption every 60 seconds
[ 1.277914] Initialise system trusted keyrings
[ 1.277928] Key type blacklist registered
[ 1.277998] workingset: timestamp_bits=40 max_order=22 bucket_order=0
[ 1.278977] zbud: loaded
[ 1.280210] Key type asymmetric registered
[ 1.280221] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.280271] io scheduler noop registered
[ 1.280271] io scheduler deadline registered
[ 1.280294] io scheduler cfq registered (default)
[ 1.280295] io scheduler mq-deadline registered
[ 1.280296] io scheduler kyber registered
[ 1.280315] io scheduler bfq registered
[ 1.281409] pcieport 0000:00:1c.0: AER enabled with IRQ 123
[ 1.281425] pcieport 0000:00:1c.5: AER enabled with IRQ 124
[ 1.281442] pcieport 0000:00:1c.6: AER enabled with IRQ 125
[ 1.281454] pcieport 0000:00:01.0: Signaling PME with IRQ 122
[ 1.281462] pcieport 0000:00:1c.0: Signaling PME with IRQ 123
[ 1.281471] pcieport 0000:00:1c.5: Signaling PME with IRQ 124
[ 1.281479] pcieport 0000:00:1c.6: Signaling PME with IRQ 125
[ 1.281495] pciehp 0000:00:1c.0:pcie004: Slot #4 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ LLActRep+
[ 1.281546] efifb: probing for efifb
[ 1.281589] efifb: framebuffer at 0xb0000000, using 32448k, total 32448k
[ 1.281590] efifb: mode is 3840x2160x32, linelength=15360, pages=1
[ 1.281591] efifb: scrolling: redraw
[ 1.281592] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.299821] Console: switching to colour frame buffer device 480x135
[ 1.317905] fb0: EFI VGA frame buffer device
[ 1.317916] intel_idle: MWAIT substates: 0x11142120
[ 1.317917] intel_idle: v0.4.1 model 0x5E
[ 1.318365] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.319911] GHES: HEST is not enabled!
[ 1.319988] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.320552] Linux agpgart interface v0.103
[ 1.321213] rtc_cmos 00:04: RTC can wake from S4
[ 1.321638] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.321722] rtc_cmos 00:04: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.321728] intel_pstate: Intel P-state driver initializing
[ 1.322896] intel_pstate: HWP enabled
[ 1.323291] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.323334] vlv2_plat_clk vlv2_plat_clk: vlv2_plat_clk initialized
[ 1.323482] NET: Registered protocol family 10
[ 1.326669] Segment Routing with IPv6
[ 1.326681] NET: Registered protocol family 17
[ 1.327166] RAS: Correctable Errors collector initialized.
[ 1.327187] microcode: sig=0x506e3, pf=0x20, revision=0xba
[ 1.327580] microcode: Microcode Update Driver: v2.2.
[ 1.327874] registered taskstats version 1
[ 1.327878] Loading compiled-in X.509 certificates
[ 1.327889] zswap: loaded using pool lzo/zbud
[ 1.329043] Magic number: 13:753:653
[ 1.329076] acpi LNXCPU:06: hash matches
[ 1.329272] rtc_cmos 00:04: setting system clock to 2017-08-11 22:37:00 UTC (1502491020)
[ 1.329826] PM: Checking hibernation image partition /dev/sda4
[ 1.329830] PM: Hibernation image not present or could not be loaded.
[ 1.330797] Freeing unused kernel memory: 1324K
[ 1.330797] Write protecting the kernel read-only data: 10240k
[ 1.331238] Freeing unused kernel memory: 1640K
[ 1.428582] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.435943] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.435965] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.437981] SCSI subsystem initialized
[ 1.438510] ACPI: bus type USB registered
[ 1.438521] usbcore: registered new interface driver usbfs
[ 1.438526] usbcore: registered new interface driver hub
[ 1.438550] usbcore: registered new device driver usb
[ 1.439215] libata version 3.00 loaded.
[ 1.440110] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.440115] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 1.441306] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00109810
[ 1.441318] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 1.441542] hub 1-0:1.0: USB hub found
[ 1.441586] hub 1-0:1.0: 16 ports detected
[ 1.455741] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.455744] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 1.455934] hub 2-0:1.0: USB hub found
[ 1.455974] hub 2-0:1.0: 8 ports detected
[ 1.459345] usb: port power management may be unreliable
[ 1.462521] ahci 0000:00:17.0: version 3.0
[ 1.462806] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[ 1.462808] ahci 0000:00:17.0: flags: 64bit ncq sntf led clo only pio slum part ems deso sadm sds apst
[ 1.491692] scsi host0: ahci
[ 1.491991] scsi host1: ahci
[ 1.492296] scsi host2: ahci
[ 1.492688] scsi host3: ahci
[ 1.492745] ata1: SATA max UDMA/133 abar m2048@0xa4434000 port 0xa4434100 irq 128
[ 1.492747] ata2: SATA max UDMA/133 abar m2048@0xa4434000 port 0xa4434180 irq 128
[ 1.492748] ata3: SATA max UDMA/133 abar m2048@0xa4434000 port 0xa4434200 irq 128
[ 1.492749] ata4: SATA max UDMA/133 abar m2048@0xa4434000 port 0xa4434280 irq 128
[ 1.535664] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.773904] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 1.805406] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.805436] ata4: SATA link down (SStatus 4 SControl 300)
[ 1.805468] ata3: SATA link down (SStatus 4 SControl 300)
[ 1.805513] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.806104] ata1.00: ATA-9: SanDisk SD8SNAT-128G-1006, Z2311006, max UDMA/100
[ 1.806108] ata1.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 1.809156] ata1.00: configured for UDMA/100
[ 1.809768] scsi 0:0:0:0: Direct-Access ATA SanDisk SD8SNAT- 1006 PQ: 0 ANSI: 5
[ 1.812350] ata2.00: ATA-9: ST2000LM003 HN-M201RAD, 2BE10001, max UDMA/133
[ 1.812354] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 1.819395] ata2.00: configured for UDMA/133
[ 1.854872] scsi 1:0:0:0: Direct-Access ATA ST2000LM003 HN-M 0001 PQ: 0 ANSI: 5
[ 1.899785] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 1.899789] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 1.899832] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.899837] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.899843] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[ 1.899847] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.899923] sd 0:0:0:0: [sda] Write Protect is off
[ 1.899926] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.899955] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.900009] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.903633] sda: sda1 sda2 sda3 sda4
[ 1.905735] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.908155] usb-storage 1-1:1.1: USB Mass Storage device detected
[ 1.908369] scsi host4: usb-storage 1-1:1.1
[ 1.908474] usbcore: registered new interface driver usb-storage
[ 2.020567] usb 1-4: new high-speed USB device number 3 using xhci_hcd
[ 2.164557] sdb: sdb1 sdb2
[ 2.166256] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 2.273895] usb 1-7: new full-speed USB device number 4 using xhci_hcd
[ 2.297667] clocksource: Switched to clocksource tsc
[ 2.487429] PM: Starting manual resume from disk
[ 2.487434] PM: Hibernation image partition 8:4 present
[ 2.487436] PM: Looking for hibernation image.
[ 2.487653] PM: Image not found (code -22)
[ 2.487655] PM: Hibernation image not present or could not be loaded.
[ 2.515679] random: fast init done
[ 2.534483] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.638745] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.641967] systemd[1]: systemd 234 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 -SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN default-hierarchy=hybrid)
[ 2.642097] systemd[1]: Detected architecture x86-64.
[ 2.644259] systemd[1]: Set hostname to <Archim-HP>.
[ 2.728718] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 2.728755] systemd[1]: Listening on Journal Socket.
[ 2.728765] systemd[1]: Reached target Remote File Systems.
[ 2.729025] systemd[1]: Created slice User and Session Slice.
[ 2.729135] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 2.729146] systemd[1]: Reached target Login Prompts.
[ 2.729170] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 2.745275] EXT4-fs (sda2): re-mounted. Opts: data=ordered
[ 2.763138] systemd-journald[212]: Received request to flush runtime journal from PID 1
[ 2.912245] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 2.912629] ACPI: Lid Switch [LID0]
[ 2.912656] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 2.912660] ACPI: Power Button [PWRB]
[ 2.912691] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 2.912695] ACPI: Power Button [PWRF]
[ 2.913200] ACPI: AC Adapter [ADP1] (on-line)
[ 2.914034] scsi 4:0:0:0: CD-ROM Linux File-CD Gadget 0401 PQ: 0 ANSI: 2
[ 2.920184] input: HP Wireless hotkeys as /devices/virtual/input/input5
[ 2.928704] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 2.929051] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 2.933409] hp_accel: laptop model unknown, using default axes configuration
[ 2.933888] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.934053] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[ 2.944192] lis3lv02d: 8 bits 3DC sensor found
[ 2.954111] device returned spurious data
[ 2.954120] ------------[ cut here ]------------
[ 2.954123] WARNING: CPU: 6 PID: 234 at drivers/misc/lis3lv02d/lis3lv02d.c:239 lis3lv02d_get_pwron_wait+0x9b/0xb0 [lis3lv02d]
[ 2.954123] Modules linked in: int3403_thermal intel_gtt syscopyarea i2c_hid sysfillrect sysimgblt fb_sys_fops hid hp_accel(+) i2c_algo_bit lis3lv02d input_polldev mei_me wmi(+) pcc_cpufreq(-) led_class processor_thermal_device intel_lpss_acpi mei intel_lpss video int340x_thermal_zone tpm_crb(+) shpchp intel_pch_thermal intel_soc_dts_iosf tpm_tis tpm_tis_core hp_wireless int3400_thermal tpm acpi_thermal_rel ac acpi_pad button sch_fq_codel ip_tables x_tables ext4 crc16 jbd2 fscrypto mbcache usb_storage sd_mod rtsx_pci_sdmmc mmc_core serio_raw atkbd libps2 ahci xhci_pci libahci xhci_hcd libata rtsx_pci usbcore scsi_mod usb_common i8042 serio
[ 2.954145] CPU: 6 PID: 234 Comm: systemd-udevd Not tainted 4.12.4-1-ARCH #1
[ 2.954146] Hardware name: HP OMEN by HP Laptop/8257, BIOS F.06 05/05/2016
[ 2.954146] task: ffff8d2a693d9d80 task.stack: ffffb4e382238000
[ 2.954148] RIP: 0010:lis3lv02d_get_pwron_wait+0x9b/0xb0 [lis3lv02d]
[ 2.954148] RSP: 0018:ffffb4e38223ba40 EFLAGS: 00010286
[ 2.954149] RAX: 000000000000001d RBX: 00000000fffffffa RCX: ffffffff97a55a68
[ 2.954150] RDX: 0000000000000000 RSI: 0000000000000082 RDI: 0000000000000287
[ 2.954150] RBP: ffffb4e38223ba58 R08: 00000000000002c8 R09: ffffffff97ca0940
[ 2.954151] R10: ffffb4e38223b930 R11: 0000000000000000 R12: ffffffffc05410c8
[ 2.954151] R13: 0000000000000000 R14: ffff8d2a6b8ca000 R15: 000000000000001c
[ 2.954152] FS: 00007febf3bef8c0(0000) GS:ffff8d2a7ed80000(0000) knlGS:0000000000000000
[ 2.954153] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2.954153] CR2: 00007febf3b9ebff CR3: 0000000468fe8000 CR4: 00000000003406e0
[ 2.954154] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2.954155] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2.954155] Call Trace:
[ 2.954158] lis3lv02d_poweron+0xa1/0x120 [lis3lv02d]
[ 2.954159] lis3lv02d_init_device+0x145/0xa80 [lis3lv02d]
[ 2.954161] lis3lv02d_add+0xe8/0x207 [hp_accel]
[ 2.954164] acpi_device_probe+0x4b/0x110
[ 2.954165] driver_probe_device+0x2ff/0x450
[ 2.954167] __driver_attach+0xa4/0xe0
[ 2.954168] ? driver_probe_device+0x450/0x450
[ 2.954169] bus_for_each_dev+0x6e/0xb0
[ 2.954170] driver_attach+0x1e/0x20
[ 2.954171] bus_add_driver+0x1d0/0x270
[ 2.954172] ? 0xffffffffc0544000
[ 2.954173] driver_register+0x60/0xe0
[ 2.954174] ? 0xffffffffc0544000
[ 2.954175] acpi_bus_register_driver+0x3c/0x50
[ 2.954177] lis3lv02d_driver_init+0x10/0x1000 [hp_accel]
[ 2.954178] do_one_initcall+0x50/0x190
[ 2.954180] ? __vunmap+0x81/0xb0
[ 2.954181] ? kfree+0x175/0x190
[ 2.954182] ? kfree+0x175/0x190
[ 2.954183] ? do_init_module+0x27/0x1e6
[ 2.954184] do_init_module+0x5f/0x1e6
[ 2.954188] load_module+0x2610/0x2ab0
[ 2.954190] SYSC_init_module+0x16b/0x1a0
[ 2.954191] ? SYSC_init_module+0x16b/0x1a0
[ 2.954195] SyS_init_module+0xe/0x10
[ 2.954197] entry_SYSCALL_64_fastpath+0x1a/0xa5
[ 2.954198] RIP: 0033:0x7febf35384da
[ 2.954198] RSP: 002b:00007fffd7eb1bb8 EFLAGS: 00000246 ORIG_RAX: 00000000000000af
[ 2.954199] RAX: ffffffffffffffda RBX: 00000000000000a7 RCX: 00007febf35384da
[ 2.954200] RDX: 00007febf2e18cb5 RSI: 0000000000007930 RDI: 000000a0cba641e0
[ 2.954200] RBP: 0000000000000004 R08: 0000000000000001 R09: 00000000000000d3
[ 2.954201] R10: 0000000000000000 R11: 0000000000000246 R12: 000000a0cae36997
[ 2.954201] R13: 000000a0cbe68200 R14: 000000a0cae47438 R15: 000000008dc73deb
[ 2.954202] Code: d8 75 2c 48 83 c4 10 5b 5d c3 80 3d 97 30 00 00 00 bb fa ff ff ff 75 da 48 c7 c7 d0 b0 51 c0 c6 05 82 30 00 00 01 e8 08 ff c6 d6 <0f> ff eb c3 e8 5c 81 b6 d6 66 90 66 2e 0f 1f 84 00 00 00 00 00
[ 2.954220] ---[ end trace a21b082edd110c16 ]---
[ 2.994403] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[ 2.994438] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[ 2.995018] usbcore: registered new interface driver uas
[ 2.996950] [Firmware Bug]: Invalid critical threshold (0)
[ 2.998123] wmi: Mapper loaded
[ 3.001323] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 3.002845] thermal LNXTHERM:00: registered as thermal_zone3
[ 3.002847] ACPI: Thermal Zone [TZ01] (49 C)
[ 3.002895] media: Linux media interface: v0.10
[ 3.005659] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 3.005665] r8169 0000:09:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 3.009471] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 3.010032] Linux video capture interface: v2.00
[ 3.014731] r8169 0000:09:00.0 eth0: RTL8168h/8111h at 0xffffb4e381975000, a0:8c:fd:2c:48:8a, XID 14100800 IRQ 130
[ 3.014733] r8169 0000:09:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 3.014946] Bluetooth: Core ver 2.22
[ 3.014966] NET: Registered protocol family 31
[ 3.014966] Bluetooth: HCI device and connection manager initialized
[ 3.014968] Bluetooth: HCI socket layer initialized
[ 3.014970] Bluetooth: L2CAP socket layer initialized
[ 3.014974] Bluetooth: SCO socket layer initialized
[ 3.017035] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 655360 ms ovfl timer
[ 3.017037] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[ 3.017037] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 3.017038] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 3.017039] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[ 3.017039] RAPL PMU: hw unit of domain psys 2^-14 Joules
[ 3.018840] Intel(R) Wireless WiFi driver for Linux
[ 3.018841] Copyright(c) 2003- 2015 Intel Corporation
[ 3.028591] r8168: loading out-of-tree module taints kernel.
[ 3.029619] iwlwifi 0000:08:00.0: Direct firmware load for iwlwifi-7265D-29.ucode failed with error -2
[ 3.029648] iwlwifi 0000:08:00.0: Direct firmware load for iwlwifi-7265D-28.ucode failed with error -2
[ 3.032739] iwlwifi 0000:08:00.0: capa flags index 3 larger than supported by driver
[ 3.032953] iwlwifi 0000:08:00.0: loaded firmware version 27.455470.0 op_mode iwlmvm
[ 3.044708] Adding 15359996k swap on /dev/sda4. Priority:-1 extents:1 across:15359996k SSFS
[ 3.050782] iTCO_vendor_support: vendor-support=0
[ 3.051752] sr 4:0:0:0: [sr0] scsi-1 drive
[ 3.051754] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.051861] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 3.053242] input: HP WMI hotkeys as /devices/virtual/input/input8
[ 3.056747] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 3.056876] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[ 3.057912] usbcore: registered new interface driver btusb
[ 3.058399] random: crng init done
[ 3.064051] r8169 0000:09:00.0 eno1: renamed from eth0
[ 3.068027] ACPI: Battery Slot [BAT0] (battery present)
[ 3.072104] Bluetooth: hci0: read Intel version: 370810011003110e00
[ 3.073193] uvcvideo: Found UVC 1.00 device HP Wide Vision HD (04f2:b56d)
[ 3.075470] AVX2 version of gcm_enc/dec engaged.
[ 3.075471] AES CTR mode by8 optimization enabled
[ 3.075708] iwlwifi 0000:08:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0x210
[ 3.077558] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 3.078412] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 3.080592] uvcvideo 1-4:1.0: Entity type for entity Extension 4 was not initialized!
[ 3.080593] uvcvideo 1-4:1.0: Entity type for entity Extension 3 was not initialized!
[ 3.080594] uvcvideo 1-4:1.0: Entity type for entity Processing 2 was not initialized!
[ 3.080595] uvcvideo 1-4:1.0: Entity type for entity Camera 1 was not initialized!
[ 3.080642] input: HP Wide Vision HD as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/input/input9
[ 3.080672] usbcore: registered new interface driver uvcvideo
[ 3.080673] USB Video Class driver (1.1.1)
[ 3.085420] pcieport 0000:00:1c.5: AER: Corrected error received: id=00e5
[ 3.085426] pcieport 0000:00:1c.5: PCIe Bus Error: severity=Corrected, type=Physical Layer, id=00e5(Receiver ID)
[ 3.085454] pcieport 0000:00:1c.5: device [8086:a115] error status/mask=00000001/00002000
[ 3.085476] pcieport 0000:00:1c.5: [ 0] Receiver Error (First)
[ 3.089481] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.8.10-fw-1.10.3.11.e.bseq
[ 3.094234] snd_hda_intel 0000:00:1f.3: failed to add i915 component master (-19)
[ 3.143923] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC295: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 3.143927] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 3.143929] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 3.143931] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 3.143932] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 3.143934] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19
[ 3.143936] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
[ 3.160117] snd_hda_codec_hdmi hdaudioC0D2: No i915 binding for Intel HDMI/DP codec
[ 3.163023] snd_hda_codec_hdmi hdaudioC0D2: No i915 binding for Intel HDMI/DP codec
[ 3.168865] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input10
[ 3.168984] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input11
[ 3.169093] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input12
[ 3.174982] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[ 3.175503] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[ 3.175534] thermal thermal_zone4: failed to read out thermal zone (-5)
[ 3.180380] iwlwifi 0000:08:00.0 wlo1: renamed from wlan0
[ 3.196522] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: data=ordered
[ 3.206010] intel_rapl: Found RAPL domain package
[ 3.206013] intel_rapl: Found RAPL domain core
[ 3.206015] intel_rapl: Found RAPL domain uncore
[ 3.206016] intel_rapl: Found RAPL domain dram
[ 3.234194] nvidia: module license 'NVIDIA' taints kernel.
[ 3.234196] Disabling lock debugging due to kernel taint
[ 3.244142] nvidia-nvlink: Nvlink Core is being initialized, major device number 243
[ 3.244377] nvidia 0000:01:00.0: enabling device (0006 -> 0007)
[ 3.244619] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 384.59 Wed Jul 19 23:53:34 PDT 2017 (using threaded interrupts)
[ 3.253815] nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms 384.59 Wed Jul 19 23:46:42 PDT 2017
[ 3.255416] [drm] [nvidia-drm] [GPU ID 0x00000100] Loading driver
[ 3.255418] [drm] Initialized nvidia-drm 0.0.0 20160202 for 0000:01:00.0 on minor 0
[ 3.365349] Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
[ 3.529896] r8169 0000:09:00.0 eno1: link down
[ 3.529899] r8169 0000:09:00.0 eno1: link down
[ 3.529977] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 3.532402] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 3.532866] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 3.539992] pcieport 0000:00:1c.5: AER: Corrected error received: id=00e5
[ 3.539998] pcieport 0000:00:1c.5: PCIe Bus Error: severity=Corrected, type=Physical Layer, id=00e5(Receiver ID)
[ 3.540080] pcieport 0000:00:1c.5: device [8086:a115] error status/mask=00000001/00002000
[ 3.540152] pcieport 0000:00:1c.5: [ 0] Receiver Error (First)
[ 3.599387] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 3.599949] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 3.607842] pcieport 0000:00:1c.5: AER: Corrected error received: id=00e5
[ 3.607852] pcieport 0000:00:1c.5: PCIe Bus Error: severity=Corrected, type=Physical Layer, id=00e5(Receiver ID)
[ 3.607957] pcieport 0000:00:1c.5: device [8086:a115] error status/mask=00000001/00002000
[ 3.608021] pcieport 0000:00:1c.5: [ 0] Receiver Error (First)
[ 3.628333] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 3.885542] psmouse serio1: synaptics: queried max coordinates: x [..5636], y [..4634]
[ 3.928426] psmouse serio1: synaptics: queried min coordinates: x [1360..], y [1298..]
[ 3.928435] psmouse serio1: synaptics: Your touchpad (PNP: SYN3239 SYN1e00 SYN0002 PNP0f13) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.
[ 3.945773] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 3.945845] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 3.945882] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 3.945918] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 3.945952] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 3.946049] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 3.946085] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 3.949390] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 3.955031] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 3.963875] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 3.964496] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 4.005646] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xf00123/0x840300/0x12e800/0x0, board id: 3114, fw id: 1805562
[ 4.030798] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 4.032382] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 4.033316] iwlwifi 0000:08:00.0: L1 Enabled - LTR Enabled
[ 4.054981] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[ 4.057814] mousedev: PS/2 mouse device common for all mice
[ 4.062325] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 4.147284] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 4.301728] nvidia-modeset: Allocated GPU:0 (GPU-b32fd181-f1b9-7e46-e3b6-7ba19b5591a3) @ PCI:0000:01:00.0
[ 4.302754] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20170303/nsarguments-95)
[ 5.169726] r8169 0000:09:00.0 eno1: link up
[ 5.169733] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready
[ 129.195580] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 129.201304] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 129.204914] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 130.072131] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 130.075930] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 130.078161] pcieport 0000:00:1c.5: AER: Corrected error received: id=00e5
[ 130.078166] pcieport 0000:00:1c.5: PCIe Bus Error: severity=Corrected, type=Physical Layer, id=00e5(Receiver ID)
[ 130.078200] pcieport 0000:00:1c.5: device [8086:a115] error status/mask=00000001/00002000
[ 130.078225] pcieport 0000:00:1c.5: [ 0] Receiver Error (First)
[ 130.080588] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not readyAt last my Xorg.0.log:
[ 3.813] (--) Log file renamed from "/var/log/Xorg.pid-390.log" to "/var/log/Xorg.0.log"
[ 3.814]
X.Org X Server 1.19.3
Release Date: 2017-03-15
[ 3.814] X Protocol Version 11, Revision 0
[ 3.814] Build Operating System: Linux 4.9.11-1-ARCH x86_64
[ 3.814] Current Operating System: Linux Archim-HP 4.12.4-1-ARCH #1 SMP PREEMPT Fri Jul 28 18:54:18 UTC 2017 x86_64
[ 3.814] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ab03a09d-da68-4801-aeab-daef74de7086 rw quiet resume=/dev/sda4
[ 3.814] Build Date: 07 April 2017 05:42:48PM
[ 3.814]
[ 3.814] Current version of pixman: 0.34.0
[ 3.814] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 3.814] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 3.814] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Aug 12 00:37:02 2017
[ 3.821] (==) Using config file: "/etc/X11/xorg.conf"
[ 3.821] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 3.821] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 3.822] (==) ServerLayout "Layout0"
[ 3.822] (**) |-->Screen "Screen0" (0)
[ 3.822] (**) | |-->Monitor "Monitor0"
[ 3.822] (**) | |-->Device "Device0"
[ 3.822] (**) |-->Input Device "Keyboard0"
[ 3.822] (**) |-->Input Device "Mouse0"
[ 3.822] (==) Automatically adding devices
[ 3.822] (==) Automatically enabling devices
[ 3.822] (==) Automatically adding GPU devices
[ 3.822] (==) Automatically binding GPU devices
[ 3.822] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 3.825] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 3.825] Entry deleted from font path.
[ 3.826] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 3.826] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 3.826] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 3.826] (WW) Disabling Keyboard0
[ 3.826] (WW) Disabling Mouse0
[ 3.826] (II) Loader magic: 0x822d60
[ 3.826] (II) Module ABI versions:
[ 3.826] X.Org ANSI C Emulation: 0.4
[ 3.826] X.Org Video Driver: 23.0
[ 3.826] X.Org XInput driver : 24.1
[ 3.826] X.Org Server Extension : 10.0
[ 3.826] (++) using VT number 1
[ 3.826] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[ 3.827] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 3.827] (**) OutputClass "nvidia" ModulePath extended to "/usr/lib/nvidia/xorg,/usr/lib/xorg/modules"
[ 3.827] (**) OutputClass "nvidia" setting /dev/dri/card0 as PrimaryGPU
[ 3.828] (--) PCI: (0:0:2:0) 8086:191b:103c:8257 rev 6, Mem @ 0xa2000000/16777216, 0xb0000000/268435456, I/O @ 0x00005000/64, BIOS @ 0x????????/131072
[ 3.828] (--) PCI:*(0:1:0:0) 10de:1427:103c:8257 rev 161, Mem @ 0xa3000000/16777216, 0x90000000/268435456, 0xa0000000/33554432, I/O @ 0x00004000/128, BIOS @ 0x????????/524288
[ 3.828] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 3.828] (II) LoadModule: "glx"
[ 3.834] (II) Loading /usr/lib/nvidia/xorg/libglx.so
[ 3.898] (II) Module glx: vendor="NVIDIA Corporation"
[ 3.898] compiled for 4.0.2, module version = 1.0.0
[ 3.898] Module class: X.Org Server Extension
[ 3.899] (II) NVIDIA GLX Module 384.59 Wed Jul 19 23:41:15 PDT 2017
[ 3.900] (II) LoadModule: "nvidia"
[ 3.909] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 3.918] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 3.919] compiled for 4.0.2, module version = 1.0.0
[ 3.919] Module class: X.Org Video Driver
[ 3.919] (II) NVIDIA dlloader X Driver 384.59 Wed Jul 19 23:14:49 PDT 2017
[ 3.919] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 3.921] (II) Loading sub module "fb"
[ 3.921] (II) LoadModule: "fb"
[ 3.921] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 3.924] (II) Module fb: vendor="X.Org Foundation"
[ 3.924] compiled for 1.19.3, module version = 1.0.0
[ 3.924] ABI class: X.Org ANSI C Emulation, version 0.4
[ 3.924] (II) Loading sub module "wfb"
[ 3.924] (II) LoadModule: "wfb"
[ 3.925] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 3.927] (II) Module wfb: vendor="X.Org Foundation"
[ 3.927] compiled for 1.19.3, module version = 1.0.0
[ 3.927] ABI class: X.Org ANSI C Emulation, version 0.4
[ 3.927] (II) Loading sub module "ramdac"
[ 3.927] (II) LoadModule: "ramdac"
[ 3.927] (II) Module "ramdac" already built-in
[ 3.931] (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
[ 3.931] (==) NVIDIA(0): RGB weight 888
[ 3.931] (==) NVIDIA(0): Default visual is TrueColor
[ 3.931] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 3.932] (II) Applying OutputClass "nvidia" options to /dev/dri/card0
[ 3.932] (**) NVIDIA(0): Option "AllowEmptyInitialConfiguration"
[ 3.932] (**) NVIDIA(0): Enabling 2D acceleration
[ 4.328] (--) NVIDIA(0): Valid display device(s) on GPU-0 at PCI:1:0:0
[ 4.328] (--) NVIDIA(0): DFP-0
[ 4.329] (II) NVIDIA(0): NVIDIA GPU GeForce GTX 965M (GM206-A) at PCI:1:0:0 (GPU-0)
[ 4.329] (--) NVIDIA(0): Memory: 4194304 kBytes
[ 4.329] (--) NVIDIA(0): VideoBIOS: 84.06.52.00.4c
[ 4.329] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[ 4.329] (--) NVIDIA(GPU-0): DFP-0: disconnected
[ 4.329] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[ 4.329] (--) NVIDIA(GPU-0): DFP-0: 165.0 MHz maximum pixel clock
[ 4.329] (--) NVIDIA(GPU-0):
[ 4.329] (==) NVIDIA(0):
[ 4.329] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 4.329] (==) NVIDIA(0): will be used as the requested mode.
[ 4.329] (==) NVIDIA(0):
[ 4.329] (--) NVIDIA(0): No enabled display devices found; starting anyway because
[ 4.329] (--) NVIDIA(0): AllowEmptyInitialConfiguration is enabled
[ 4.330] (II) NVIDIA(0): Validated MetaModes:
[ 4.330] (II) NVIDIA(0): "NULL"
[ 4.330] (II) NVIDIA(0): Virtual screen size determined to be 640 x 480
[ 4.330] (WW) NVIDIA(0): Unable to get display device for DPI computation.
[ 4.330] (==) NVIDIA(0): DPI set to (75, 75); computed from built-in default
[ 4.330] (--) Depth 24 pixmap format is 32 bpp
[ 4.330] (II) NVIDIA: Using 12288.00 MB of virtual memory for indirect memory
[ 4.330] (II) NVIDIA: access.
[ 4.334] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 4.334] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 4.334] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 4.334] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 4.334] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 4.334] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 4.334] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 4.334] (II) NVIDIA(0): Config Options in the README.
[ 4.348] (II) NVIDIA(0): Setting mode "NULL"
[ 4.354] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 4.355] (==) NVIDIA(0): Backing store enabled
[ 4.355] (==) NVIDIA(0): Silken mouse enabled
[ 4.356] (**) NVIDIA(0): DPMS enabled
[ 4.356] (WW) NVIDIA(0): Option "PrimaryGPU" is not used
[ 4.356] (II) Loading sub module "dri2"
[ 4.356] (II) LoadModule: "dri2"
[ 4.356] (II) Module "dri2" already built-in
[ 4.356] (II) NVIDIA(0): [DRI2] Setup complete
[ 4.356] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 4.356] (--) RandR disabled
[ 4.359] (II) Initializing extension GLX
[ 4.359] (II) Indirect GLX disabled.
[ 4.451] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 4.451] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 4.451] (**) Power Button: Applying InputClass "system-keyboard"
[ 4.451] (II) LoadModule: "libinput"
[ 4.451] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[ 4.456] (II) Module libinput: vendor="X.Org Foundation"
[ 4.456] compiled for 1.19.3, module version = 0.25.1
[ 4.456] Module class: X.Org XInput Driver
[ 4.456] ABI class: X.Org XInput driver, version 24.1
[ 4.456] (II) Using input driver 'libinput' for 'Power Button'
[ 4.456] (**) Power Button: always reports core events
[ 4.456] (**) Option "Device" "/dev/input/event3"
[ 4.456] (**) Option "_source" "server/udev"
[ 4.457] (II) event3 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 4.457] (II) event3 - (II) Power Button: (II) device is a keyboard
[ 4.457] (II) event3 - (II) Power Button: (II) device removed
[ 4.476] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event3"
[ 4.476] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 4.476] (**) Option "xkb_layout" "de"
[ 4.490] (II) event3 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 4.490] (II) event3 - (II) Power Button: (II) device is a keyboard
[ 4.490] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 4.490] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 4.490] (**) Power Button: Applying InputClass "system-keyboard"
[ 4.490] (II) Using input driver 'libinput' for 'Power Button'
[ 4.490] (**) Power Button: always reports core events
[ 4.490] (**) Option "Device" "/dev/input/event2"
[ 4.490] (**) Option "_source" "server/udev"
[ 4.490] (II) event2 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 4.490] (II) event2 - (II) Power Button: (II) device is a keyboard
[ 4.490] (II) event2 - (II) Power Button: (II) device removed
[ 4.513] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3/event2"
[ 4.513] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 4.513] (**) Option "xkb_layout" "de"
[ 4.513] (II) event2 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 4.513] (II) event2 - (II) Power Button: (II) device is a keyboard
[ 4.513] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 4.513] (II) No input driver specified, ignoring this device.
[ 4.513] (II) This device may have been added with another device file.
[ 4.514] (II) config/udev: Adding input device HP Wide Vision HD (/dev/input/event7)
[ 4.514] (**) HP Wide Vision HD: Applying InputClass "libinput keyboard catchall"
[ 4.514] (**) HP Wide Vision HD: Applying InputClass "system-keyboard"
[ 4.514] (II) Using input driver 'libinput' for 'HP Wide Vision HD'
[ 4.514] (**) HP Wide Vision HD: always reports core events
[ 4.514] (**) Option "Device" "/dev/input/event7"
[ 4.514] (**) Option "_source" "server/udev"
[ 4.514] (II) event7 - (II) HP Wide Vision HD: (II) is tagged by udev as: Keyboard
[ 4.514] (II) event7 - (II) HP Wide Vision HD: (II) device is a keyboard
[ 4.514] (II) event7 - (II) HP Wide Vision HD: (II) device removed
[ 4.556] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/input/input9/event7"
[ 4.556] (II) XINPUT: Adding extended input device "HP Wide Vision HD" (type: KEYBOARD, id 8)
[ 4.556] (**) Option "xkb_layout" "de"
[ 4.557] (II) event7 - (II) HP Wide Vision HD: (II) is tagged by udev as: Keyboard
[ 4.557] (II) event7 - (II) HP Wide Vision HD: (II) device is a keyboard
[ 4.557] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event8)
[ 4.557] (II) No input driver specified, ignoring this device.
[ 4.557] (II) This device may have been added with another device file.
[ 4.557] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event9)
[ 4.557] (II) No input driver specified, ignoring this device.
[ 4.557] (II) This device may have been added with another device file.
[ 4.557] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event10)
[ 4.557] (II) No input driver specified, ignoring this device.
[ 4.557] (II) This device may have been added with another device file.
[ 4.557] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 4.557] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[ 4.557] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard"
[ 4.557] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[ 4.557] (**) AT Translated Set 2 keyboard: always reports core events
[ 4.557] (**) Option "Device" "/dev/input/event0"
[ 4.557] (**) Option "_source" "server/udev"
[ 4.558] (II) event0 - (II) AT Translated Set 2 keyboard: (II) is tagged by udev as: Keyboard
[ 4.558] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device is a keyboard
[ 4.558] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device removed
[ 4.576] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 4.576] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[ 4.576] (**) Option "xkb_layout" "de"
[ 4.577] (II) event0 - (II) AT Translated Set 2 keyboard: (II) is tagged by udev as: Keyboard
[ 4.577] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device is a keyboard
[ 4.577] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event11)
[ 4.577] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "libinput touchpad catchall"
[ 4.577] (II) Using input driver 'libinput' for 'SynPS/2 Synaptics TouchPad'
[ 4.577] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 4.577] (**) Option "Device" "/dev/input/event11"
[ 4.577] (**) Option "_source" "server/udev"
[ 4.577] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) is tagged by udev as: Touchpad
[ 4.577] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device is a touchpad
[ 4.578] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device removed
[ 4.617] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input7/event11"
[ 4.617] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 10)
[ 4.617] (**) Option "AccelerationScheme" "none"
[ 4.617] (**) SynPS/2 Synaptics TouchPad: (accel) selected scheme none/0
[ 4.617] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 4.617] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 4.618] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) is tagged by udev as: Touchpad
[ 4.618] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device is a touchpad
[ 4.618] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 4.618] (II) No input driver specified, ignoring this device.
[ 4.618] (II) This device may have been added with another device file.
[ 4.619] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[ 4.619] (II) No input driver specified, ignoring this device.
[ 4.619] (II) This device may have been added with another device file.
[ 4.619] (II) config/udev: Adding input device HP Wireless hotkeys (/dev/input/event4)
[ 4.620] (**) HP Wireless hotkeys: Applying InputClass "libinput keyboard catchall"
[ 4.620] (**) HP Wireless hotkeys: Applying InputClass "system-keyboard"
[ 4.620] (II) Using input driver 'libinput' for 'HP Wireless hotkeys'
[ 4.620] (**) HP Wireless hotkeys: always reports core events
[ 4.620] (**) Option "Device" "/dev/input/event4"
[ 4.620] (**) Option "_source" "server/udev"
[ 4.620] (II) event4 - (II) HP Wireless hotkeys: (II) is tagged by udev as: Keyboard
[ 4.620] (II) event4 - (II) HP Wireless hotkeys: (II) device is a keyboard
[ 4.620] (II) event4 - (II) HP Wireless hotkeys: (II) device removed
[ 4.666] (**) Option "config_info" "udev:/sys/devices/virtual/input/input5/event4"
[ 4.666] (II) XINPUT: Adding extended input device "HP Wireless hotkeys" (type: KEYBOARD, id 11)
[ 4.666] (**) Option "xkb_layout" "de"
[ 4.667] (II) event4 - (II) HP Wireless hotkeys: (II) is tagged by udev as: Keyboard
[ 4.667] (II) event4 - (II) HP Wireless hotkeys: (II) device is a keyboard
[ 4.668] (II) config/udev: Adding input device HP WMI hotkeys (/dev/input/event6)
[ 4.668] (**) HP WMI hotkeys: Applying InputClass "libinput keyboard catchall"
[ 4.668] (**) HP WMI hotkeys: Applying InputClass "system-keyboard"
[ 4.668] (II) Using input driver 'libinput' for 'HP WMI hotkeys'
[ 4.668] (**) HP WMI hotkeys: always reports core events
[ 4.668] (**) Option "Device" "/dev/input/event6"
[ 4.668] (**) Option "_source" "server/udev"
[ 4.668] (II) event6 - (II) HP WMI hotkeys: (II) is tagged by udev as: Keyboard Switch
[ 4.668] (II) event6 - (II) HP WMI hotkeys: (II) device is a keyboard
[ 4.668] (II) event6 - (II) HP WMI hotkeys: (II) device removed
[ 4.706] (**) Option "config_info" "udev:/sys/devices/virtual/input/input8/event6"
[ 4.706] (II) XINPUT: Adding extended input device "HP WMI hotkeys" (type: KEYBOARD, id 12)
[ 4.706] (**) Option "xkb_layout" "de"
[ 4.707] (II) event6 - (II) HP WMI hotkeys: (II) is tagged by udev as: Keyboard Switch
[ 4.707] (II) event6 - (II) HP WMI hotkeys: (II) device is a keyboard
[ 4.712] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 4.712] (II) No input driver specified, ignoring this device.
[ 4.712] (II) This device may have been added with another device file.
[ 4.712] (II) config/udev: removing device SynPS/2 Synaptics TouchPad
[ 4.712] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device removed
[ 4.770] (II) UnloadModule: "libinput"
[ 4.770] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event11)
[ 4.770] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "libinput touchpad catchall"
[ 4.770] (II) Using input driver 'libinput' for 'SynPS/2 Synaptics TouchPad'
[ 4.770] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 4.770] (**) Option "Device" "/dev/input/event11"
[ 4.770] (**) Option "_source" "server/udev"
[ 4.771] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) is tagged by udev as: Touchpad
[ 4.771] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device is a touchpad
[ 4.771] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device removed
[ 4.816] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input7/event11"
[ 4.816] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 10)
[ 4.816] (**) Option "AccelerationScheme" "none"
[ 4.816] (**) SynPS/2 Synaptics TouchPad: (accel) selected scheme none/0
[ 4.816] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 4.816] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 4.817] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) is tagged by udev as: Touchpad
[ 4.817] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device is a touchpad
[ 12.460] (II) event3 - (II) Power Button: (II) device removed
[ 12.477] (II) event2 - (II) Power Button: (II) device removed
[ 12.497] (II) event7 - (II) HP Wide Vision HD: (II) device removed
[ 12.537] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device removed
[ 12.560] (II) event4 - (II) HP Wireless hotkeys: (II) device removed
[ 12.600] (II) event6 - (II) HP WMI hotkeys: (II) device removed
[ 12.650] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device removed
[ 13.659] (--) NVIDIA(GPU-0): DFP-0: disconnected
[ 13.660] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[ 13.660] (--) NVIDIA(GPU-0): DFP-0: 165.0 MHz maximum pixel clock
[ 13.660] (--) NVIDIA(GPU-0):
[ 13.662] (II) NVIDIA(0): Setting mode "NULL"
[ 13.665] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 13.665] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 13.665] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 13.665] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 13.665] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 13.665] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 13.665] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 13.665] (II) NVIDIA(0): Config Options in the README.
[ 13.675] (II) event3 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 13.675] (II) event3 - (II) Power Button: (II) device is a keyboard
[ 13.675] (II) event2 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 13.675] (II) event2 - (II) Power Button: (II) device is a keyboard
[ 13.676] (II) event7 - (II) HP Wide Vision HD: (II) is tagged by udev as: Keyboard
[ 13.676] (II) event7 - (II) HP Wide Vision HD: (II) device is a keyboard
[ 13.676] (II) event0 - (II) AT Translated Set 2 keyboard: (II) is tagged by udev as: Keyboard
[ 13.676] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device is a keyboard
[ 13.676] (II) event4 - (II) HP Wireless hotkeys: (II) is tagged by udev as: Keyboard
[ 13.676] (II) event4 - (II) HP Wireless hotkeys: (II) device is a keyboard
[ 13.677] (II) event6 - (II) HP WMI hotkeys: (II) is tagged by udev as: Keyboard Switch
[ 13.677] (II) event6 - (II) HP WMI hotkeys: (II) device is a keyboard
[ 13.677] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) is tagged by udev as: Touchpad
[ 13.677] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device is a touchpad
[ 15.419] (II) event3 - (II) Power Button: (II) device removed
[ 15.450] (II) event2 - (II) Power Button: (II) device removed
[ 15.470] (II) event7 - (II) HP Wide Vision HD: (II) device removed
[ 15.510] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device removed
[ 15.530] (II) event4 - (II) HP Wireless hotkeys: (II) device removed
[ 15.570] (II) event6 - (II) HP WMI hotkeys: (II) device removed
[ 15.610] (II) event11 - (II) SynPS/2 Synaptics TouchPad: (II) device removedLooking forward to hear your approaches to that problem,
Greetings
fishcop
Last edited by fishcop (2017-08-13 16:32:36)
Offline
#2 2017-08-11 23:49:17
- jasonwryan
- Anarchist
- From: .nz
- Registered: 2009-05-09
- Posts: 30,426
- Website
Re: [Solved] Screen freezing problem with nvidia-driver
Don't use nvidia-xconfig: it generates a broken config.
Offline
#3 2017-08-12 00:11:43
- V1del
- Forum Moderator
- Registered: 2012-10-16
- Posts: 25,435
Re: [Solved] Screen freezing problem with nvidia-driver
Not only that, but blacklisting the i915 drivers will also break your system additionally. Because the intel GPU is what's connected to your display, you absolutely will have to keep the kernel module around in some form or shape. Revert all configuration changes you mentioned so far (the blacklists and the nvidia-xconfig generated one) and follow https://wiki.archlinux.org/index.php/NV … timus#SDDM
Offline
#4 2017-08-13 14:53:40
- fishcop
- Member
- Registered: 2016-02-16
- Posts: 26
Re: [Solved] Screen freezing problem with nvidia-driver
Hey Guys,
thanks for the replies. I first made a xconfig according to the wiki(which isn't that precisely in that mattter unfortunately):
# nvidia-xconfig: version 384.59 (buildmeister@swio-display-x64-rhel04-01) Thu Jul 20 01:03:28 PDT 2017
Section "Device"
Identifier "Nvidia Card"
Driver "nvidia"
VendorName "NVIDIA Corporation"
Option "NoLogo" "true"
EndSection
Section "Device"
Driver "nvidia"
Option "NoLogo"
VendorName "Hewlett Packard"
Screen 0
EndSectionMoreover I deleted my Blacklist-file. Still i have almost the same error, but the cursor is now blinking. If I do a check of the status of sddm, I see that there was an error loading sddm, stating
(code=dumped, signal=SEGV)After stopping sddm, I started a x-session(using startx), i get the following:
xinit: giving up
xinit: unable to connect to X server: Connection refused
xinit: server errorOffline
#5 2017-08-13 15:42:22
- jkrmnj
- Member
- Registered: 2017-03-04
- Posts: 1
Re: [Solved] Screen freezing problem with nvidia-driver
From my experience with getting a nvidia card and an Intel card to work on a laptop, you should completely ignore the actual Nvidia page's instructions for configuring. Instead, you can follow the Nvidia Optimus page and its steps. When it gets to the part about modifying the .xinitrc file, skip down to the link posted earlier (https://wiki.archlinux.org/index.php/NV … timus#SDDM) and do that instead.
Offline
#6 2017-08-13 15:49:05
- V1del
- Forum Moderator
- Registered: 2012-10-16
- Posts: 25,435
Re: [Solved] Screen freezing problem with nvidia-driver
You don't need any xorg.conf (I maybe should have outright stated to delete the conf instead of "reverting" which would be the same in that context), the one mentioned on the Optimus page will however not be harmful to the setup attempt, but will also not have a noticeable benefit either.
Offline
#7 2017-08-13 16:16:04
- fishcop
- Member
- Registered: 2016-02-16
- Posts: 26
Re: [Solved] Screen freezing problem with nvidia-driver
Thank you, the Optimus configuration did the job, I will mark this post as solved
Offline