Arch Linux

trojanfoliarz

Member

Registered: 2018-07-19

Posts: 9

[SOLVED] Huion Tablet - What to do to make it work?

I'm using Huion tablet ("NEW 1060 PLUS") and i want to make it work on KDE, secuirity boot mode is disabled.

I installed digimend-kernel-drivers-dkms-git, kcm-wacomtablet packages, but does not work.

I tried to execute command:

sudo modprobe -r hid-kye hid-uclogic hid-polostar hid-viewsonic

And I get output:

modprobe: FATAL: Module hid-polostar not found.

I tried to install from source code and i get this output:

asdf@asdf ~/digimend-kernel-drivers $: make

make -C /lib/modules/4.17.8-1-ARCH/build SUBDIRS=/home/asdf/digimend-kernel-drivers modules
make[1]: Entery to the directoey '/usr/lib/modules/4.17.8-1-ARCH/build'
make[1]: *** There are no rules to perform the object 'modules'. Stop.
make[1]: Leaving the directory '/usr/lib/modules/4.17.8-1-ARCH/build'
make: *** [Makefile:19: modules] Error 2

I also try to install it with using debtap, but does not work
What can I do?

Last edited by trojanfoliarz (2018-07-25 14:12:45)

loqs

Member

Registered: 2014-03-06

Posts: 18,037

Re: [SOLVED] Huion Tablet - What to do to make it work?

What was the result of the DKMS build after you installed digimend-kernel-drivers-dkms-git ?

trojanfoliarz

Member

Registered: 2018-07-19

Posts: 9

Re: [SOLVED] Huion Tablet - What to do to make it work?

My Huion 1060 PLUS start working!!! The reason was missing dependence, so I wiill explain what to do to make it work:

1) Install dependencies: digimend-kernel-drivers-dkms-git(AUR) linux-headers:

yaourt -S digimend-kernel-drivers-dkms-git linux-headers --noconfirm

2) Use command:

sudo modprobe -r hid-kye hid-uclogic hid-polostar hid-viewsonic

3)reboot system:

reboot

4) After reboot plug your tablet. If will not working just unplug it and plug it again to USB port, and should start working.

Last edited by trojanfoliarz (2018-07-25 14:44:57)

ww_kayak

Member

Registered: 2017-12-08

Posts: 1

Re: [SOLVED] Huion Tablet - What to do to make it work?

UPDATE: It's tough to get the latest info, and I'm a noob, but for me... (kernel 5.04/KDE) which uses libinput as the default,  I was able to make Huion 1060 PLUS work, including the KDE GUI configuration, with the following:

yay -S digimend-kernel-drivers-dkms-git
pacman -S dkms
pacman -S xf86-input-wacom
pacman -S kcm-wacomtablet (GUI configuration tool)

Then modify /etc/X11/xorg.conf.d/xx-tablet.conf
     Section "InputClass"
                  Identifier "UC-Logic on Wacom"
                  MatchUSBID "256c:006e"
                  MatchDevicePath "/dev/input/event*"
                  Driver "wacom"
      EndSection

KDE system settings should now have a tablet configuration option, which lets you set the buttons

* buttons 4,5,6,7 are used internally for... I forget, but you can't use them. And, for me, buttons 1, 2, 3 are the same as the mouse.

If I'm way off base let me know. I'm always willing to learn

Last edited by ww_kayak (2019-03-26 00:47:20)