You are not logged in.
- Topics: Active | Unanswered
#1 2018-04-22 13:23:28
- MelvIsntNormal
- Member
- Registered: 2018-04-22
- Posts: 12
Random black screen and freezing issues (AMD Ryzen 2400G)
I'm having some difficulty diagnosing and fixing a seemingly random issue with my new PC. During use, the screen may freeze up completely, meaning that all I can do is hold the power button on my PC until it turns off. When I turn it back on, it get's past GRUB and outputs a lot of lines about cleaning up orphaned inodes, and then just stops. Nothing else happens. I can leave it for hours and nothing will happen. I have to manually restart it again. On other occasions, I boot up the PC and it just goes black after GRUB, and I have to manually reset it.
I have a feeling that it's something to do with my components. I'm using an AMD Ryzen 2400G and a Gigabyte Gaming AB350N motherboard, and making sure I had everything updated for that was a challenge in itself. I updated the motherboard BIOS twice (I didn't get the latest version the first time), turned off global C-states after reading this thread and this thread, and made sure that the kernel was updated to 4.16 since I read that there were fixes for the APU in there. I also made sure that the AMDGPU driver was installed and updated.
I'm not sure what else I can check. Could someone potentially point me in the right direction?
Here's the output of lspci:
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15d0
Subsystem: Advanced Micro Devices, Inc. [AMD] Device 15d0
Flags: fast devsel
00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD] Device 15d1
Subsystem: Advanced Micro Devices, Inc. [AMD] Device 15d1
Flags: bus master, fast devsel, latency 0, IRQ 25
Capabilities: <access denied>
00:01.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) PCIe Dummy Host Bridge
Flags: fast devsel
00:01.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Device 15d3 (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 26
Bus: primary=00, secondary=01, subordinate=08, sec-latency=0
I/O behind bridge: 0000f000-0000ffff [size=4K]
Memory behind bridge: fe600000-fe8fffff [size=3M]
Prefetchable memory behind bridge: 00000000f0300000-00000000f03fffff [size=1M]
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:08.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) PCIe Dummy Host Bridge
Flags: fast devsel
00:08.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Device 15db (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 27
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 0000e000-0000efff [size=4K]
Memory behind bridge: fe200000-fe5fffff [size=4M]
Prefetchable memory behind bridge: 00000000e0000000-00000000f01fffff [size=258M]
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:08.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Device 15dc (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 28
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
I/O behind bridge: None
Memory behind bridge: fe900000-fe9fffff [size=1M]
Prefetchable memory behind bridge: None
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 61)
Subsystem: Gigabyte Technology Co., Ltd FCH SMBus Controller
Flags: 66MHz, medium devsel
Kernel driver in use: piix4_smbus
Kernel modules: i2c_piix4, sp5100_tco
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 51)
Subsystem: Gigabyte Technology Co., Ltd FCH LPC Bridge
Flags: bus master, 66MHz, medium devsel, latency 0
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15e8
Flags: fast devsel
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15e9
Flags: fast devsel
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15ea
Flags: fast devsel
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15eb
Flags: fast devsel
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15ec
Flags: fast devsel
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15ed
Flags: fast devsel
00:18.6 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15ee
Flags: fast devsel
00:18.7 Host bridge: Advanced Micro Devices, Inc. [AMD] Device 15ef
Flags: fast devsel
01:00.0 USB controller: Advanced Micro Devices, Inc. [AMD] USB 3.1 XHCI Controller (rev 02) (prog-if 30 [XHCI])
Subsystem: ASMedia Technology Inc. 300 Series Chipset USB 3.1 xHCI Controller
Flags: bus master, fast devsel, latency 0, IRQ 40
Memory at fe8a0000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
01:00.1 SATA controller: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset SATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASMedia Technology Inc. 300 Series Chipset SATA Controller
Flags: bus master, fast devsel, latency 0, IRQ 42
Memory at fe880000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fe800000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
01:00.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Device 43b2 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 30
Bus: primary=01, secondary=02, subordinate=08, sec-latency=0
I/O behind bridge: 0000f000-0000ffff [size=4K]
Memory behind bridge: fe600000-fe7fffff [size=2M]
Prefetchable memory behind bridge: 00000000f0300000-00000000f03fffff [size=1M]
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
02:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 32
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: None
Memory behind bridge: None
Prefetchable memory behind bridge: None
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
02:01.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 34
Bus: primary=02, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: None
Memory behind bridge: None
Prefetchable memory behind bridge: None
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
02:04.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 35
Bus: primary=02, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: None
Memory behind bridge: None
Prefetchable memory behind bridge: None
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
02:05.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 36
Bus: primary=02, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: None
Memory behind bridge: fe700000-fe7fffff [size=1M]
Prefetchable memory behind bridge: None
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
02:06.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 37
Bus: primary=02, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: None
Memory behind bridge: None
Prefetchable memory behind bridge: None
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
02:07.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 39
Bus: primary=02, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 0000f000-0000ffff [size=4K]
Memory behind bridge: fe600000-fe6fffff [size=1M]
Prefetchable memory behind bridge: 00000000f0300000-00000000f03fffff [size=1M]
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
06:00.0 Network controller: Intel Corporation Wireless 3165 (rev 81)
Subsystem: Intel Corporation Dual Band Wireless AC 3165
Flags: bus master, fast devsel, latency 0, IRQ 64
Memory at fe700000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)
Subsystem: Gigabyte Technology Co., Ltd Onboard Ethernet
Flags: bus master, fast devsel, latency 0, IRQ 63
I/O ports at f000 [size=256]
Memory at fe600000 (64-bit, non-prefetchable) [size=4K]
Memory at f0300000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
09:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Raven Bridge [Radeon Vega Series / Radeon Vega Mobile Series] (rev c6) (prog-if 00 [VGA controller])
Subsystem: Gigabyte Technology Co., Ltd Raven Bridge [Radeon Vega Series / Radeon Vega Mobile Series] (Radeon RX Vega 11)
Flags: bus master, fast devsel, latency 0, IRQ 68
Memory at e0000000 (64-bit, prefetchable) [size=256M]
Memory at f0000000 (64-bit, prefetchable) [size=2M]
I/O ports at e000 [size=256]
Memory at fe500000 (32-bit, non-prefetchable) [size=512K]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: amdgpu
Kernel modules: amdgpu
09:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Device 15de
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 15de
Flags: bus master, fast devsel, latency 0, IRQ 66
Memory at fe588000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
09:00.2 Encryption controller: Advanced Micro Devices, Inc. [AMD] Device 15df
Subsystem: Advanced Micro Devices, Inc. [AMD] Device 15df
Flags: bus master, fast devsel, latency 0, IRQ 5
Memory at fe400000 (32-bit, non-prefetchable) [size=1M]
Memory at fe58c000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
09:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Device 15e0 (prog-if 30 [XHCI])
Subsystem: Gigabyte Technology Co., Ltd Device 5007
Flags: bus master, fast devsel, latency 0, IRQ 41
Memory at fe300000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
09:00.4 USB controller: Advanced Micro Devices, Inc. [AMD] Device 15e1 (prog-if 30 [XHCI])
Subsystem: Gigabyte Technology Co., Ltd Device 5007
Flags: bus master, fast devsel, latency 0, IRQ 51
Memory at fe200000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
09:00.6 Audio device: Advanced Micro Devices, Inc. [AMD] Device 15e3
Subsystem: Gigabyte Technology Co., Ltd Device a182
Flags: bus master, fast devsel, latency 0, IRQ 67
Memory at fe580000 (32-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
0a:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 61) (prog-if 01 [AHCI 1.0])
Subsystem: Gigabyte Technology Co., Ltd FCH SATA Controller [AHCI mode]
Flags: bus master, fast devsel, latency 0, IRQ 61
Memory at fe900000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahciLast edited by MelvIsntNormal (2018-04-23 09:33:28)
Offline
#2 2018-04-22 13:47:53
- dockland
- Member
- From: Sweden
- Registered: 2015-06-06
- Posts: 861
Re: Random black screen and freezing issues (AMD Ryzen 2400G)
dmesg output might help us a bit
I possess a device, in my pocket, that is capable of accessing the entirety of information known to man.
I use it to look at funny pictures of cats and to argue with strangers.
Offline
#3 2018-04-22 15:04:17
- MelvIsntNormal
- Member
- Registered: 2018-04-22
- Posts: 12
Re: Random black screen and freezing issues (AMD Ryzen 2400G)
dockland wrote:
dmesg output might help us a bit
[ 0.000000] Linux version 4.16.3-1-ARCH (builduser@heftig-2067) (gcc version 7.3.1 20180406 (GCC)) #1 SMP PREEMPT Thu Apr 19 09:17:56 UTC 2018
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=0ffa6bb0-433a-40dd-918d-31ac56d8c39b rw quiet
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'compacted' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000000a0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000003ffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000004000000-0x0000000004009fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000000400a000-0x0000000009cfffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000009d00000-0x0000000009ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000a000000-0x000000000affffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000b000000-0x000000000b01ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000b020000-0x000000009ba68fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009ba69000-0x000000009bb8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009bb90000-0x000000009bc85fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009bc86000-0x000000009c055fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009c056000-0x000000009cec7fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009cec8000-0x000000009cf58fff] type 20
[ 0.000000] BIOS-e820: [mem 0x000000009cf59000-0x000000009effffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009f000000-0x00000000dfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fd800000-0x00000000fdffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fea00000-0x00000000fea0ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb80000-0x00000000fec01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec30000-0x00000000fec30fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fedc2000-0x00000000fedcffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fedd4000-0x00000000fedd5fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000feefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021f33ffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.60 by American Megatrends
[ 0.000000] efi: ACPI 2.0=0x9bc86000 ACPI=0x9bc86000 SMBIOS=0x9cd94000 SMBIOS 3.0=0x9cd93000 ESRT=0x9a4a6018 MEMATTR=0x97c0f018
[ 0.000000] random: fast init done
[ 0.000000] SMBIOS 3.1.1 present.
[ 0.000000] DMI: Gigabyte Technology Co., Ltd. AB350N-Gaming WIFI/AB350N-Gaming WIFI-CF, BIOS F23d 04/17/2018
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x21f340 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF write-through
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back
[ 0.000000] 2 base 0000C0000000 mask FFFFE0000000 write-back
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 0000000220000000 aka 8704M
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0x9f000 max_arch_pfn = 0x400000000
[ 0.000000] esrt: Reserving ESRT space from 0x000000009a4a6018 to 0x000000009a4a6050.
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ (ptrval)] 96000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] BRK [0x13164a000, 0x13164afff] PGTABLE
[ 0.000000] BRK [0x13164b000, 0x13164bfff] PGTABLE
[ 0.000000] BRK [0x13164c000, 0x13164cfff] PGTABLE
[ 0.000000] BRK [0x13164d000, 0x13164dfff] PGTABLE
[ 0.000000] BRK [0x13164e000, 0x13164efff] PGTABLE
[ 0.000000] BRK [0x13164f000, 0x13164ffff] PGTABLE
[ 0.000000] BRK [0x131650000, 0x131650fff] PGTABLE
[ 0.000000] BRK [0x131651000, 0x131651fff] PGTABLE
[ 0.000000] BRK [0x131652000, 0x131652fff] PGTABLE
[ 0.000000] BRK [0x131653000, 0x131653fff] PGTABLE
[ 0.000000] BRK [0x131654000, 0x131654fff] PGTABLE
[ 0.000000] BRK [0x131655000, 0x131655fff] PGTABLE
[ 0.000000] Secure boot could not be determined
[ 0.000000] RAMDISK: [mem 0x3723d000-0x37915fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x000000009BC86000 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x000000009BC86098 0000B4 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x000000009BC8C628 000114 (v06 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has valid Length but zero Address: 0x0000000000000000/0x1 (20180105/tbfadt-658)
[ 0.000000] ACPI: DSDT 0x000000009BC861E8 00643C (v02 ALASKA A M I 01072009 INTL 20120913)
[ 0.000000] ACPI: FACS 0x000000009C03FE00 000040
[ 0.000000] ACPI: APIC 0x000000009BC8C740 0000DE (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x000000009BC8C820 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FIDT 0x000000009BC8C868 00009C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: SSDT 0x000000009BC8C908 005367 (v02 ALASKA A M I 00000002 MSFT 02000002)
[ 0.000000] ACPI: CRAT 0x000000009BC91C70 000810 (v01 ALASKA A M I 00000001 AMD 00000001)
[ 0.000000] ACPI: CDIT 0x000000009BC92480 000029 (v01 ALASKA A M I 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000009BC924B0 002E6E (v01 ALASKA A M I 00000001 INTL 20120913)
[ 0.000000] ACPI: MCFG 0x000000009BC95320 00003C (v01 ALASKA A M I 01072009 MSFT 00010013)
[ 0.000000] ACPI: HPET 0x000000009BC95360 000038 (v01 ALASKA A M I 01072009 AMI 00000005)
[ 0.000000] ACPI: UEFI 0x000000009BC95398 000042 (v01 ALASKA A M I 00000000 00000000)
[ 0.000000] ACPI: BGRT 0x000000009BC953E0 000038 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: IVRS 0x000000009BC95418 0000D0 (v02 ALASKA A M I 00000001 AMD 00000000)
[ 0.000000] ACPI: SSDT 0x000000009BC954E8 0000F8 (v01 ALASKA A M I 00001000 INTL 20120913)
[ 0.000000] ACPI: SSDT 0x000000009BC955E0 000E96 (v01 ALASKA A M I 00000001 INTL 20120913)
[ 0.000000] ACPI: SSDT 0x000000009BC96478 000850 (v01 ALASKA A M I 00000001 INTL 20120913)
[ 0.000000] ACPI: SSDT 0x000000009BC96CC8 001A41 (v01 ALASKA A M I 00000001 INTL 20120913)
[ 0.000000] ACPI: WSMT 0x000000009BC98710 000028 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000021f33ffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x21f33d000-0x21f33ffff]
[ 0.000000] tsc: Fast TSC calibration failed
[ 0.000000] tsc: Using PIT calibration value
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000021f33ffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009ffff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x0000000003ffffff]
[ 0.000000] node 0: [mem 0x000000000400a000-0x0000000009cfffff]
[ 0.000000] node 0: [mem 0x000000000a000000-0x000000000affffff]
[ 0.000000] node 0: [mem 0x000000000b020000-0x000000009ba68fff]
[ 0.000000] node 0: [mem 0x000000009bb90000-0x000000009bc85fff]
[ 0.000000] node 0: [mem 0x000000009cf59000-0x000000009effffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000021f33ffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000021f33ffff]
[ 0.000000] On node 0 totalpages: 1821627
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 28 pages reserved
[ 0.000000] DMA zone: 3999 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 10020 pages used for memmap
[ 0.000000] DMA32 zone: 641244 pages, LIFO batch:31
[ 0.000000] Normal zone: 18381 pages used for memmap
[ 0.000000] Normal zone: 1176384 pages, LIFO batch:31
[ 0.000000] Reserved but unavailable: 97 pages
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 9, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 10, version 33, address 0xfec01000, GSI 24-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 16 CPUs, 8 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x04000000-0x04009fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x09d00000-0x09ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0b000000-0x0b01ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9ba69000-0x9bb8ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9bc86000-0x9c055fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9c056000-0x9cec7fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9cec8000-0x9cf58fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f000000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfd7fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfd800000-0xfdffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe000000-0xfe9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfea00000-0xfea0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfea10000-0xfeb7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb80000-0xfec01fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfec2ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec30000-0xfec30fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec31000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xfedc1fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfedc2000-0xfedcffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfedd0000-0xfedd3fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfedd4000-0xfedd5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfedd6000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfeefffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfef00000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xe0000000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[ 0.000000] setup_percpu: NR_CPUS:320 nr_cpumask_bits:320 nr_cpu_ids:16 nr_node_ids:1
[ 0.000000] percpu: Embedded 46 pages/cpu @ (ptrval) s151552 r8192 d28672 u262144
[ 0.000000] pcpu-alloc: s151552 r8192 d28672 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 12 13 14 15
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1793134
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=0ffa6bb0-433a-40dd-918d-31ac56d8c39b rw quiet
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 7018220K/7286508K available (10252K kernel code, 1263K rwdata, 3372K rodata, 1452K init, 632K bss, 268288K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[ 0.000000] ftrace: allocating 31747 entries in 125 pages
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=16.
[ 0.000000] RCU priority boosting: priority 1 delay 500 ms.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16
[ 0.000000] NR_IRQS: 20736, nr_irqs: 1096, preallocated irqs: 16
[ 0.000000] Offload RCU callbacks from CPUs: .
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] ACPI: Core revision 20180105
[ 0.000000] ACPI BIOS Error (bug): Failure creating [\_SB.SMIC], AE_ALREADY_EXISTS (20180105/dswload-380)
[ 0.000000] ACPI Error: AE_ALREADY_EXISTS, During name lookup/catalog (20180105/psobject-252)
[ 0.000000] ACPI Error: AE_ALREADY_EXISTS, (SSDT: A M I) while loading table (20180105/tbxfload-228)
[ 0.000000] ACPI Error: 1 table load failures, 6 successful (20180105/tbxfload-246)
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] APIC: Switch to symmetric I/O mode setup
[ 0.003333] Switched APIC routing to physical flat.
[ 0.003333] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.019999] tsc: Fast TSC calibration failed
[ 0.023333] tsc: PIT calibration matches HPET. 1 loops
[ 0.023333] tsc: Detected 3593.275 MHz processor
[ 0.023333] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x33cb8271fd9, max_idle_ns: 440795316803 ns
[ 0.023333] Calibrating delay loop (skipped), value calculated using timer frequency.. 7189.98 BogoMIPS (lpj=11977583)
[ 0.023333] pid_max: default: 32768 minimum: 301
[ 0.026913] Security Framework initialized
[ 0.026914] Yama: becoming mindful.
[ 0.028481] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.029276] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.029366] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.029389] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.030283] CPU: Physical Processor ID: 0
[ 0.030283] CPU: Processor Core ID: 0
[ 0.030390] mce: CPU supports 23 MCE banks
[ 0.030407] LVT offset 1 assigned for vector 0xf9
[ 0.030454] LVT offset 2 assigned for vector 0xf4
[ 0.030464] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 512
[ 0.030464] Last level dTLB entries: 4KB 1536, 2MB 1536, 4MB 768, 1GB 0
[ 0.030465] Spectre V2 : Mitigation: Full AMD retpoline
[ 0.030466] Spectre V2 : Spectre v2 mitigation: Enabling Indirect Branch Prediction Barrier
[ 0.031217] Freeing SMP alternatives memory: 24K
[ 0.036666] smpboot: CPU0: AMD Ryzen 5 2400G with Radeon Vega Graphics (family: 0x17, model: 0x11, stepping: 0x0)
[ 0.046674] Performance Events: Fam17h core perfctr, AMD PMU driver.
[ 0.046679] ... version: 0
[ 0.046679] ... bit width: 48
[ 0.046679] ... generic registers: 6
[ 0.046680] ... value mask: 0000ffffffffffff
[ 0.046681] ... max period: 00007fffffffffff
[ 0.046681] ... fixed-purpose events: 0
[ 0.046682] ... event mask: 000000000000003f
[ 0.053338] Hierarchical SRCU implementation.
[ 0.073717] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.080002] smp: Bringing up secondary CPUs ...
[ 0.110013] x86: Booting SMP configuration:
[ 0.110014] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7
[ 0.292240] smp: Brought up 1 node, 8 CPUs
[ 0.292240] smpboot: Max logical packages: 2
[ 0.292240] smpboot: Total of 8 processors activated (57515.91 BogoMIPS)
[ 0.293485] devtmpfs: initialized
[ 0.293485] x86/mm: Memory block size: 128MB
[ 0.294204] PM: Registering ACPI NVS region [mem 0x04000000-0x04009fff] (40960 bytes)
[ 0.294204] PM: Registering ACPI NVS region [mem 0x9bc86000-0x9c055fff] (3997696 bytes)
[ 0.294204] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.294204] futex hash table entries: 4096 (order: 6, 262144 bytes)
[ 0.294204] pinctrl core: initialized pinctrl subsystem
[ 0.294204] RTC time: 13:00:06, date: 04/22/18
[ 0.294601] NET: Registered protocol family 16
[ 0.294781] cpuidle: using governor ladder
[ 0.296677] cpuidle: using governor menu
[ 0.296803] ACPI: bus type PCI registered
[ 0.296803] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.297022] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.297026] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.297033] PCI: Using configuration type 1 for base access
[ 0.300072] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.300072] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.300208] ACPI: Added _OSI(Module Device)
[ 0.300209] ACPI: Added _OSI(Processor Device)
[ 0.300209] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.300210] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.300476] ACPI BIOS Error (bug): Failure looking up [\PTOS], AE_NOT_FOUND (20180105/psargs-364)
[ 0.300488] ACPI Error: Method parse/execution failed \, AE_NOT_FOUND (20180105/psparse-550)
[ 0.300496] ACPI: Executed 2 blocks of module-level executable AML code
[ 0.305972] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.307584] ACPI: Interpreter enabled
[ 0.307597] ACPI: (supports S0 S3 S4 S5)
[ 0.307597] ACPI: Using IOAPIC for interrupt routing
[ 0.307915] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.308135] ACPI: Enabled 2 GPEs in block 00 to 1F
[ 0.310804] ACPI: Power Resource [P0ST] (on)
[ 0.310836] ACPI: Power Resource [P3ST] (on)
[ 0.315996] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.315999] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.316215] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.316224] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.316545] PCI host bridge to bus 0000:00
[ 0.316546] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.316548] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.316548] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.316549] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.316550] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.316551] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.316552] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfec2ffff window]
[ 0.316553] pci_bus 0000:00: root bus resource [mem 0xfee00000-0xffffffff window]
[ 0.316554] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.316563] pci 0000:00:00.0: [1022:15d0] type 00 class 0x060000
[ 0.316690] pci 0000:00:00.2: [1022:15d1] type 00 class 0x080600
[ 0.316842] pci 0000:00:01.0: [1022:1452] type 00 class 0x060000
[ 0.316962] pci 0000:00:01.2: [1022:15d3] type 01 class 0x060400
[ 0.317065] pci 0000:00:01.2: PME# supported from D0 D3hot D3cold
[ 0.317187] pci 0000:00:08.0: [1022:1452] type 00 class 0x060000
[ 0.317306] pci 0000:00:08.1: [1022:15db] type 01 class 0x060400
[ 0.317359] pci 0000:00:08.1: enabling Extended Tags
[ 0.317419] pci 0000:00:08.1: PME# supported from D0 D3hot D3cold
[ 0.317507] pci 0000:00:08.2: [1022:15dc] type 01 class 0x060400
[ 0.317558] pci 0000:00:08.2: enabling Extended Tags
[ 0.317609] pci 0000:00:08.2: PME# supported from D0 D3hot D3cold
[ 0.317720] pci 0000:00:14.0: [1022:790b] type 00 class 0x0c0500
[ 0.317906] pci 0000:00:14.3: [1022:790e] type 00 class 0x060100
[ 0.318117] pci 0000:00:18.0: [1022:15e8] type 00 class 0x060000
[ 0.318168] pci 0000:00:18.1: [1022:15e9] type 00 class 0x060000
[ 0.318221] pci 0000:00:18.2: [1022:15ea] type 00 class 0x060000
[ 0.318280] pci 0000:00:18.3: [1022:15eb] type 00 class 0x060000
[ 0.318331] pci 0000:00:18.4: [1022:15ec] type 00 class 0x060000
[ 0.318392] pci 0000:00:18.5: [1022:15ed] type 00 class 0x060000
[ 0.318452] pci 0000:00:18.6: [1022:15ee] type 00 class 0x060000
[ 0.318504] pci 0000:00:18.7: [1022:15ef] type 00 class 0x060000
[ 0.318649] pci 0000:01:00.0: [1022:43bb] type 00 class 0x0c0330
[ 0.318679] pci 0000:01:00.0: reg 0x10: [mem 0xfe8a0000-0xfe8a7fff 64bit]
[ 0.318783] pci 0000:01:00.0: PME# supported from D3hot D3cold
[ 0.318880] pci 0000:01:00.1: [1022:43b7] type 00 class 0x010601
[ 0.318943] pci 0000:01:00.1: reg 0x24: [mem 0xfe880000-0xfe89ffff]
[ 0.318952] pci 0000:01:00.1: reg 0x30: [mem 0xfe800000-0xfe87ffff pref]
[ 0.319004] pci 0000:01:00.1: PME# supported from D3hot D3cold
[ 0.319071] pci 0000:01:00.2: [1022:43b2] type 01 class 0x060400
[ 0.319171] pci 0000:01:00.2: PME# supported from D3hot D3cold
[ 0.330030] pci 0000:00:01.2: PCI bridge to [bus 01-08]
[ 0.330036] pci 0000:00:01.2: bridge window [io 0xf000-0xffff]
[ 0.330039] pci 0000:00:01.2: bridge window [mem 0xfe600000-0xfe8fffff]
[ 0.330045] pci 0000:00:01.2: bridge window [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.330185] pci 0000:02:00.0: [1022:43b4] type 01 class 0x060400
[ 0.330308] pci 0000:02:00.0: PME# supported from D3hot D3cold
[ 0.330403] pci 0000:02:01.0: [1022:43b4] type 01 class 0x060400
[ 0.330522] pci 0000:02:01.0: PME# supported from D3hot D3cold
[ 0.330626] pci 0000:02:04.0: [1022:43b4] type 01 class 0x060400
[ 0.330745] pci 0000:02:04.0: PME# supported from D3hot D3cold
[ 0.330840] pci 0000:02:05.0: [1022:43b4] type 01 class 0x060400
[ 0.330958] pci 0000:02:05.0: PME# supported from D3hot D3cold
[ 0.331056] pci 0000:02:06.0: [1022:43b4] type 01 class 0x060400
[ 0.331175] pci 0000:02:06.0: PME# supported from D3hot D3cold
[ 0.331280] pci 0000:02:07.0: [1022:43b4] type 01 class 0x060400
[ 0.331402] pci 0000:02:07.0: PME# supported from D3hot D3cold
[ 0.331525] pci 0000:01:00.2: PCI bridge to [bus 02-08]
[ 0.331532] pci 0000:01:00.2: bridge window [io 0xf000-0xffff]
[ 0.331536] pci 0000:01:00.2: bridge window [mem 0xfe600000-0xfe7fffff]
[ 0.331543] pci 0000:01:00.2: bridge window [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.331597] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 0.331675] pci 0000:02:01.0: PCI bridge to [bus 04]
[ 0.331744] pci 0000:02:04.0: PCI bridge to [bus 05]
[ 0.331846] pci 0000:06:00.0: [8086:3165] type 00 class 0x028000
[ 0.331919] pci 0000:06:00.0: reg 0x10: [mem 0xfe700000-0xfe701fff 64bit]
[ 0.332164] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[ 0.343388] pci 0000:02:05.0: PCI bridge to [bus 06]
[ 0.343398] pci 0000:02:05.0: bridge window [mem 0xfe700000-0xfe7fffff]
[ 0.343469] pci 0000:02:06.0: PCI bridge to [bus 07]
[ 0.343553] pci 0000:08:00.0: [10ec:8168] type 00 class 0x020000
[ 0.343600] pci 0000:08:00.0: reg 0x10: [io 0xf000-0xf0ff]
[ 0.343642] pci 0000:08:00.0: reg 0x18: [mem 0xfe600000-0xfe600fff 64bit]
[ 0.343669] pci 0000:08:00.0: reg 0x20: [mem 0xf0300000-0xf0303fff 64bit pref]
[ 0.343821] pci 0000:08:00.0: supports D1 D2
[ 0.343822] pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.353371] pci 0000:02:07.0: PCI bridge to [bus 08]
[ 0.353378] pci 0000:02:07.0: bridge window [io 0xf000-0xffff]
[ 0.353382] pci 0000:02:07.0: bridge window [mem 0xfe600000-0xfe6fffff]
[ 0.353389] pci 0000:02:07.0: bridge window [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.353566] pci 0000:09:00.0: [1002:15dd] type 00 class 0x030000
[ 0.353618] pci 0000:09:00.0: reg 0x10: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.353639] pci 0000:09:00.0: reg 0x18: [mem 0xf0000000-0xf01fffff 64bit pref]
[ 0.353653] pci 0000:09:00.0: reg 0x20: [io 0xe000-0xe0ff]
[ 0.353666] pci 0000:09:00.0: reg 0x24: [mem 0xfe500000-0xfe57ffff]
[ 0.353689] pci 0000:09:00.0: enabling Extended Tags
[ 0.353707] pci 0000:09:00.0: BAR 0: assigned to efifb
[ 0.353814] pci 0000:09:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.353959] pci 0000:09:00.1: [1002:15de] type 00 class 0x040300
[ 0.353993] pci 0000:09:00.1: reg 0x10: [mem 0xfe588000-0xfe58bfff]
[ 0.354075] pci 0000:09:00.1: enabling Extended Tags
[ 0.354156] pci 0000:09:00.1: PME# supported from D1 D2 D3hot D3cold
[ 0.354257] pci 0000:09:00.2: [1022:15df] type 00 class 0x108000
[ 0.354314] pci 0000:09:00.2: reg 0x18: [mem 0xfe400000-0xfe4fffff]
[ 0.354351] pci 0000:09:00.2: reg 0x24: [mem 0xfe58c000-0xfe58dfff]
[ 0.354374] pci 0000:09:00.2: enabling Extended Tags
[ 0.354542] pci 0000:09:00.3: [1022:15e0] type 00 class 0x0c0330
[ 0.354582] pci 0000:09:00.3: reg 0x10: [mem 0xfe300000-0xfe3fffff 64bit]
[ 0.354653] pci 0000:09:00.3: enabling Extended Tags
[ 0.354742] pci 0000:09:00.3: PME# supported from D0 D3hot D3cold
[ 0.354846] pci 0000:09:00.4: [1022:15e1] type 00 class 0x0c0330
[ 0.354886] pci 0000:09:00.4: reg 0x10: [mem 0xfe200000-0xfe2fffff 64bit]
[ 0.354957] pci 0000:09:00.4: enabling Extended Tags
[ 0.355046] pci 0000:09:00.4: PME# supported from D0 D3hot D3cold
[ 0.355141] pci 0000:09:00.6: [1022:15e3] type 00 class 0x040300
[ 0.355175] pci 0000:09:00.6: reg 0x10: [mem 0xfe580000-0xfe587fff]
[ 0.355257] pci 0000:09:00.6: enabling Extended Tags
[ 0.355337] pci 0000:09:00.6: PME# supported from D0 D3hot D3cold
[ 0.355502] pci 0000:00:08.1: PCI bridge to [bus 09]
[ 0.355509] pci 0000:00:08.1: bridge window [io 0xe000-0xefff]
[ 0.355512] pci 0000:00:08.1: bridge window [mem 0xfe200000-0xfe5fffff]
[ 0.355518] pci 0000:00:08.1: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.355617] pci 0000:0a:00.0: [1022:7901] type 00 class 0x010601
[ 0.355702] pci 0000:0a:00.0: reg 0x24: [mem 0xfe900000-0xfe9007ff]
[ 0.355722] pci 0000:0a:00.0: enabling Extended Tags
[ 0.355800] pci 0000:0a:00.0: PME# supported from D3hot D3cold
[ 0.355913] pci 0000:00:08.2: PCI bridge to [bus 0a]
[ 0.355921] pci 0000:00:08.2: bridge window [mem 0xfe900000-0xfe9fffff]
[ 0.356360] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11 14 15) *0
[ 0.356430] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 11 14 15) *0
[ 0.356490] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 11 14 15) *0
[ 0.356567] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 11 14 15) *0
[ 0.356635] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 0.356696] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 0.356751] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 0.356806] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 0.357315] pci 0000:09:00.0: vgaarb: setting as boot VGA device
[ 0.357315] pci 0000:09:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.357315] pci 0000:09:00.0: vgaarb: bridge control possible
[ 0.357315] vgaarb: loaded
[ 0.357315] EDAC MC: Ver: 3.0.0
[ 0.357315] Registered efivars operations
[ 0.373422] PCI: Using ACPI for IRQ routing
[ 0.376284] PCI: pci_cache_line_size set to 64 bytes
[ 0.376699] e820: reserve RAM buffer [mem 0x09d00000-0x0bffffff]
[ 0.376708] e820: reserve RAM buffer [mem 0x0b000000-0x0bffffff]
[ 0.376708] e820: reserve RAM buffer [mem 0x9ba69000-0x9bffffff]
[ 0.376709] e820: reserve RAM buffer [mem 0x9bc86000-0x9bffffff]
[ 0.376709] e820: reserve RAM buffer [mem 0x9f000000-0x9fffffff]
[ 0.376710] e820: reserve RAM buffer [mem 0x21f340000-0x21fffffff]
[ 0.376853] NetLabel: Initializing
[ 0.376854] NetLabel: domain hash size = 128
[ 0.376854] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.376863] NetLabel: unlabeled traffic allowed by default
[ 0.376865] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.376865] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.380000] clocksource: Switched to clocksource tsc-early
[ 0.391253] VFS: Disk quotas dquot_6.6.0
[ 0.391295] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.391414] pnp: PnP ACPI init
[ 0.391601] system 00:00: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.391605] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.391678] system 00:01: [mem 0xfeb80000-0xfebfffff] could not be reserved
[ 0.391681] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.391792] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.391925] system 00:03: [io 0x0a00-0x0a2f] has been reserved
[ 0.391926] system 00:03: [io 0x0a30-0x0a3f] has been reserved
[ 0.391927] system 00:03: [io 0x0a40-0x0a4f] has been reserved
[ 0.391930] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.392155] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.392156] system 00:04: [io 0x040b] has been reserved
[ 0.392157] system 00:04: [io 0x04d6] has been reserved
[ 0.392158] system 00:04: [io 0x0c00-0x0c01] has been reserved
[ 0.392159] system 00:04: [io 0x0c14] has been reserved
[ 0.392160] system 00:04: [io 0x0c50-0x0c51] has been reserved
[ 0.392161] system 00:04: [io 0x0c52] has been reserved
[ 0.392162] system 00:04: [io 0x0c6c] has been reserved
[ 0.392162] system 00:04: [io 0x0c6f] has been reserved
[ 0.392163] system 00:04: [io 0x0cd0-0x0cd1] has been reserved
[ 0.392164] system 00:04: [io 0x0cd2-0x0cd3] has been reserved
[ 0.392165] system 00:04: [io 0x0cd4-0x0cd5] has been reserved
[ 0.392166] system 00:04: [io 0x0cd6-0x0cd7] has been reserved
[ 0.392167] system 00:04: [io 0x0cd8-0x0cdf] has been reserved
[ 0.392168] system 00:04: [io 0x0800-0x089f] has been reserved
[ 0.392169] system 00:04: [io 0x0b00-0x0b0f] has been reserved
[ 0.392169] system 00:04: [io 0x0b20-0x0b3f] has been reserved
[ 0.392170] system 00:04: [io 0x0900-0x090f] has been reserved
[ 0.392171] system 00:04: [io 0x0910-0x091f] has been reserved
[ 0.392172] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.392174] system 00:04: [mem 0xfec01000-0xfec01fff] could not be reserved
[ 0.392175] system 00:04: [mem 0xfedc0000-0xfedc0fff] has been reserved
[ 0.392176] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.392177] system 00:04: [mem 0xfed80000-0xfed8ffff] could not be reserved
[ 0.392178] system 00:04: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.392179] system 00:04: [mem 0xff000000-0xffffffff] has been reserved
[ 0.392181] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.392573] pnp: PnP ACPI: found 5 devices
[ 0.398502] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.398604] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 0.398620] pci 0000:02:01.0: PCI bridge to [bus 04]
[ 0.398634] pci 0000:02:04.0: PCI bridge to [bus 05]
[ 0.398648] pci 0000:02:05.0: PCI bridge to [bus 06]
[ 0.398653] pci 0000:02:05.0: bridge window [mem 0xfe700000-0xfe7fffff]
[ 0.398663] pci 0000:02:06.0: PCI bridge to [bus 07]
[ 0.398677] pci 0000:02:07.0: PCI bridge to [bus 08]
[ 0.398679] pci 0000:02:07.0: bridge window [io 0xf000-0xffff]
[ 0.398684] pci 0000:02:07.0: bridge window [mem 0xfe600000-0xfe6fffff]
[ 0.398688] pci 0000:02:07.0: bridge window [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.398694] pci 0000:01:00.2: PCI bridge to [bus 02-08]
[ 0.398696] pci 0000:01:00.2: bridge window [io 0xf000-0xffff]
[ 0.398701] pci 0000:01:00.2: bridge window [mem 0xfe600000-0xfe7fffff]
[ 0.398705] pci 0000:01:00.2: bridge window [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.398711] pci 0000:00:01.2: PCI bridge to [bus 01-08]
[ 0.398713] pci 0000:00:01.2: bridge window [io 0xf000-0xffff]
[ 0.398718] pci 0000:00:01.2: bridge window [mem 0xfe600000-0xfe8fffff]
[ 0.398722] pci 0000:00:01.2: bridge window [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.398731] pci 0000:00:08.1: PCI bridge to [bus 09]
[ 0.398733] pci 0000:00:08.1: bridge window [io 0xe000-0xefff]
[ 0.398737] pci 0000:00:08.1: bridge window [mem 0xfe200000-0xfe5fffff]
[ 0.398741] pci 0000:00:08.1: bridge window [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.398748] pci 0000:00:08.2: PCI bridge to [bus 0a]
[ 0.398753] pci 0000:00:08.2: bridge window [mem 0xfe900000-0xfe9fffff]
[ 0.398764] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.398765] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.398766] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.398766] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.398767] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.398768] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.398769] pci_bus 0000:00: resource 10 [mem 0xe0000000-0xfec2ffff window]
[ 0.398770] pci_bus 0000:00: resource 11 [mem 0xfee00000-0xffffffff window]
[ 0.398771] pci_bus 0000:01: resource 0 [io 0xf000-0xffff]
[ 0.398772] pci_bus 0000:01: resource 1 [mem 0xfe600000-0xfe8fffff]
[ 0.398773] pci_bus 0000:01: resource 2 [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.398774] pci_bus 0000:02: resource 0 [io 0xf000-0xffff]
[ 0.398775] pci_bus 0000:02: resource 1 [mem 0xfe600000-0xfe7fffff]
[ 0.398775] pci_bus 0000:02: resource 2 [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.398777] pci_bus 0000:06: resource 1 [mem 0xfe700000-0xfe7fffff]
[ 0.398778] pci_bus 0000:08: resource 0 [io 0xf000-0xffff]
[ 0.398779] pci_bus 0000:08: resource 1 [mem 0xfe600000-0xfe6fffff]
[ 0.398779] pci_bus 0000:08: resource 2 [mem 0xf0300000-0xf03fffff 64bit pref]
[ 0.398781] pci_bus 0000:09: resource 0 [io 0xe000-0xefff]
[ 0.398782] pci_bus 0000:09: resource 1 [mem 0xfe200000-0xfe5fffff]
[ 0.398782] pci_bus 0000:09: resource 2 [mem 0xe0000000-0xf01fffff 64bit pref]
[ 0.398784] pci_bus 0000:0a: resource 1 [mem 0xfe900000-0xfe9fffff]
[ 0.398998] NET: Registered protocol family 2
[ 0.399292] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes)
[ 0.399317] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.399448] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.399689] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.399757] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.399792] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.399909] NET: Registered protocol family 1
[ 0.400133] pci 0000:09:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.400344] PCI: CLS 64 bytes, default 64
[ 0.400379] Unpacking initramfs...
[ 0.473988] Freeing initrd memory: 7012K
[ 0.474021] AMD-Vi: Unable to write to IOMMU perf counter.
[ 0.474136] pci 0000:00:00.2: can't derive routing for PCI INT A
[ 0.474137] pci 0000:00:00.2: PCI INT A: not connected
[ 0.474638] iommu: Adding device 0000:00:01.0 to group 0
[ 0.474869] iommu: Adding device 0000:00:01.2 to group 1
[ 0.475093] iommu: Adding device 0000:00:08.0 to group 2
[ 0.475323] iommu: Adding device 0000:00:08.1 to group 3
[ 0.475342] iommu: Adding device 0000:00:08.2 to group 2
[ 0.475553] iommu: Adding device 0000:00:14.0 to group 4
[ 0.475568] iommu: Adding device 0000:00:14.3 to group 4
[ 0.475797] iommu: Adding device 0000:00:18.0 to group 5
[ 0.475820] iommu: Adding device 0000:00:18.1 to group 5
[ 0.475835] iommu: Adding device 0000:00:18.2 to group 5
[ 0.475849] iommu: Adding device 0000:00:18.3 to group 5
[ 0.475864] iommu: Adding device 0000:00:18.4 to group 5
[ 0.475878] iommu: Adding device 0000:00:18.5 to group 5
[ 0.475893] iommu: Adding device 0000:00:18.6 to group 5
[ 0.475907] iommu: Adding device 0000:00:18.7 to group 5
[ 0.476139] iommu: Adding device 0000:01:00.0 to group 6
[ 0.476177] iommu: Adding device 0000:01:00.1 to group 6
[ 0.476204] iommu: Adding device 0000:01:00.2 to group 6
[ 0.476221] iommu: Adding device 0000:02:00.0 to group 6
[ 0.476237] iommu: Adding device 0000:02:01.0 to group 6
[ 0.476253] iommu: Adding device 0000:02:04.0 to group 6
[ 0.476269] iommu: Adding device 0000:02:05.0 to group 6
[ 0.476292] iommu: Adding device 0000:02:06.0 to group 6
[ 0.476308] iommu: Adding device 0000:02:07.0 to group 6
[ 0.476335] iommu: Adding device 0000:06:00.0 to group 6
[ 0.476359] iommu: Adding device 0000:08:00.0 to group 6
[ 0.476671] iommu: Adding device 0000:09:00.0 to group 7
[ 0.476751] iommu: Using direct mapping for device 0000:09:00.0
[ 0.476898] iommu: Adding device 0000:09:00.1 to group 8
[ 0.476940] iommu: Adding device 0000:09:00.2 to group 8
[ 0.476975] iommu: Adding device 0000:09:00.3 to group 8
[ 0.477009] iommu: Adding device 0000:09:00.4 to group 8
[ 0.477043] iommu: Adding device 0000:09:00.6 to group 8
[ 0.477068] iommu: Adding device 0000:0a:00.0 to group 2
[ 0.477407] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
[ 0.477407] AMD-Vi: Extended features (0x4f77ef22294ada):
[ 0.477408] PPR NX GT IA GA PC GA_vAPIC
[ 0.477411] AMD-Vi: Interrupt remapping enabled
[ 0.477411] AMD-Vi: virtual APIC enabled
[ 0.524331] AMD-Vi: Lazy IO/TLB flushing enabled
[ 0.525090] amd_uncore: AMD NB counters detected
[ 0.525094] amd_uncore: AMD LLC counters detected
[ 0.525249] Scanning for low memory corruption every 60 seconds
[ 0.525877] Initialise system trusted keyrings
[ 0.525920] Key type blacklist registered
[ 0.526008] workingset: timestamp_bits=44 max_order=21 bucket_order=0
[ 0.527425] zbud: loaded
[ 0.529201] Key type asymmetric registered
[ 0.529202] Asymmetric key parser 'x509' registered
[ 0.529266] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.529317] io scheduler noop registered
[ 0.529318] io scheduler deadline registered
[ 0.529427] io scheduler cfq registered (default)
[ 0.529427] io scheduler mq-deadline registered
[ 0.529428] io scheduler kyber registered
[ 0.529442] io scheduler bfq registered
[ 0.531390] pcieport 0000:00:01.2: AER enabled with IRQ 26
[ 0.531405] pcieport 0000:00:01.2: Signaling PME with IRQ 26
[ 0.531430] pcieport 0000:00:08.1: Signaling PME with IRQ 27
[ 0.531454] pcieport 0000:00:08.2: Signaling PME with IRQ 28
[ 0.531537] efifb: probing for efifb
[ 0.531549] efifb: framebuffer at 0xe0000000, using 3072k, total 3072k
[ 0.531550] efifb: mode is 1024x768x32, linelength=4096, pages=1
[ 0.531551] efifb: scrolling: redraw
[ 0.531552] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.533065] Console: switching to colour frame buffer device 128x48
[ 0.534478] fb0: EFI VGA frame buffer device
[ 0.534558] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.534565] ACPI: Power Button [PWRB]
[ 0.534606] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.534623] ACPI: Power Button [PWRF]
[ 0.541609] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.543000] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.543407] NET: Registered protocol family 10
[ 0.546130] Segment Routing with IPv6
[ 0.546156] NET: Registered protocol family 17
[ 0.546574] RAS: Correctable Errors collector initialized.
[ 0.546881] microcode: CPU0: patch_level=0x0810100b
[ 0.546886] microcode: CPU1: patch_level=0x0810100b
[ 0.546890] microcode: CPU2: patch_level=0x0810100b
[ 0.546893] microcode: CPU3: patch_level=0x0810100b
[ 0.546898] microcode: CPU4: patch_level=0x0810100b
[ 0.546901] microcode: CPU5: patch_level=0x0810100b
[ 0.546912] microcode: CPU6: patch_level=0x0810100b
[ 0.546916] microcode: CPU7: patch_level=0x0810100b
[ 0.546943] microcode: Microcode Update Driver: v2.2.
[ 0.546965] sched_clock: Marking stable (546939404, 0)->(638452174, -91512770)
[ 0.547164] registered taskstats version 1
[ 0.547170] Loading compiled-in X.509 certificates
[ 0.547208] zswap: loaded using pool lzo/zbud
[ 0.549633] Key type big_key registered
[ 0.550224] Magic number: 14:978:28
[ 0.550290] hctosys: unable to open rtc device (rtc0)
[ 0.552579] Freeing unused kernel memory: 1452K
[ 0.552581] Write protecting the kernel read-only data: 16384k
[ 0.553102] Freeing unused kernel memory: 2016K
[ 0.554837] Freeing unused kernel memory: 724K
[ 0.649160] SCSI subsystem initialized
[ 0.650574] ACPI: bus type USB registered
[ 0.650594] usbcore: registered new interface driver usbfs
[ 0.650601] usbcore: registered new interface driver hub
[ 0.650665] usbcore: registered new device driver usb
[ 0.652316] libata version 3.00 loaded.
[ 0.653998] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 0.654003] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 0.709370] xhci_hcd 0000:01:00.0: hcc params 0x0200ef81 hci version 0x110 quirks 0x48000410
[ 0.709552] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.709553] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.709554] usb usb1: Product: xHCI Host Controller
[ 0.709555] usb usb1: Manufacturer: Linux 4.16.3-1-ARCH xhci-hcd
[ 0.709556] usb usb1: SerialNumber: 0000:01:00.0
[ 0.709669] hub 1-0:1.0: USB hub found
[ 0.709685] hub 1-0:1.0: 10 ports detected
[ 0.709982] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 0.709984] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 0.709986] xhci_hcd 0000:01:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[ 0.710011] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.710025] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.710026] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.710027] usb usb2: Product: xHCI Host Controller
[ 0.710028] usb usb2: Manufacturer: Linux 4.16.3-1-ARCH xhci-hcd
[ 0.710029] usb usb2: SerialNumber: 0000:01:00.0
[ 0.710094] hub 2-0:1.0: USB hub found
[ 0.710102] hub 2-0:1.0: 4 ports detected
[ 0.710204] usb: port power management may be unreliable
[ 0.710300] ahci 0000:01:00.1: version 3.0
[ 0.710448] xhci_hcd 0000:09:00.3: xHCI Host Controller
[ 0.710459] xhci_hcd 0000:09:00.3: new USB bus registered, assigned bus number 3
[ 0.710584] ahci 0000:01:00.1: SSS flag set, parallel bus scan disabled
[ 0.710636] ahci 0000:01:00.1: AHCI 0001.0301 32 slots 8 ports 6 Gbps 0x33 impl SATA mode
[ 0.710639] ahci 0000:01:00.1: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part sxs deso sadm sds apst
[ 0.710659] xhci_hcd 0000:09:00.3: hcc params 0x0270ffe5 hci version 0x110 quirks 0x00000410
[ 0.711479] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.711480] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.711481] usb usb3: Product: xHCI Host Controller
[ 0.711482] usb usb3: Manufacturer: Linux 4.16.3-1-ARCH xhci-hcd
[ 0.711483] usb usb3: SerialNumber: 0000:09:00.3
[ 0.711557] scsi host0: ahci
[ 0.711594] hub 3-0:1.0: USB hub found
[ 0.711607] hub 3-0:1.0: 4 ports detected
[ 0.711811] xhci_hcd 0000:09:00.3: xHCI Host Controller
[ 0.711813] xhci_hcd 0000:09:00.3: new USB bus registered, assigned bus number 4
[ 0.711814] xhci_hcd 0000:09:00.3: Host supports USB 3.1 Enhanced SuperSpeed
[ 0.711827] scsi host1: ahci
[ 0.711858] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.711872] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.711872] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.711873] usb usb4: Product: xHCI Host Controller
[ 0.711874] usb usb4: Manufacturer: Linux 4.16.3-1-ARCH xhci-hcd
[ 0.711875] usb usb4: SerialNumber: 0000:09:00.3
[ 0.711968] hub 4-0:1.0: USB hub found
[ 0.711982] hub 4-0:1.0: 4 ports detected
[ 0.712020] scsi host2: ahci
[ 0.712144] scsi host3: ahci
[ 0.712332] scsi host4: ahci
[ 0.712392] xhci_hcd 0000:09:00.4: xHCI Host Controller
[ 0.712394] xhci_hcd 0000:09:00.4: new USB bus registered, assigned bus number 5
[ 0.712490] scsi host5: ahci
[ 0.712573] xhci_hcd 0000:09:00.4: hcc params 0x0260ffe5 hci version 0x110 quirks 0x00000410
[ 0.712649] scsi host6: ahci
[ 0.712825] scsi host7: ahci
[ 0.712869] ata1: SATA max UDMA/133 abar m131072@0xfe880000 port 0xfe880100 irq 42
[ 0.712871] ata2: SATA max UDMA/133 abar m131072@0xfe880000 port 0xfe880180 irq 42
[ 0.712872] ata3: DUMMY
[ 0.712873] ata4: DUMMY
[ 0.712875] ata5: SATA max UDMA/133 abar m131072@0xfe880000 port 0xfe880300 irq 42
[ 0.712877] ata6: SATA max UDMA/133 abar m131072@0xfe880000 port 0xfe880380 irq 42
[ 0.712877] ata7: DUMMY
[ 0.712878] ata8: DUMMY
[ 0.713140] ahci 0000:0a:00.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 0.713143] ahci 0000:0a:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part sxs
[ 0.713146] ahci 0000:0a:00.0: both AHCI_HFLAG_MULTI_MSI flag set and custom irq handler implemented
[ 0.713355] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.713356] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.713356] usb usb5: Product: xHCI Host Controller
[ 0.713357] usb usb5: Manufacturer: Linux 4.16.3-1-ARCH xhci-hcd
[ 0.713358] usb usb5: SerialNumber: 0000:09:00.4
[ 0.713473] hub 5-0:1.0: USB hub found
[ 0.713483] hub 5-0:1.0: 1 port detected
[ 0.713589] xhci_hcd 0000:09:00.4: xHCI Host Controller
[ 0.713591] xhci_hcd 0000:09:00.4: new USB bus registered, assigned bus number 6
[ 0.713593] xhci_hcd 0000:09:00.4: Host supports USB 3.1 Enhanced SuperSpeed
[ 0.713622] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.713635] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.713636] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.713637] usb usb6: Product: xHCI Host Controller
[ 0.713638] usb usb6: Manufacturer: Linux 4.16.3-1-ARCH xhci-hcd
[ 0.713639] usb usb6: SerialNumber: 0000:09:00.4
[ 0.713653] scsi host8: ahci
[ 0.713729] hub 6-0:1.0: USB hub found
[ 0.713739] hub 6-0:1.0: 1 port detected
[ 0.713821] scsi host9: ahci
[ 0.713910] ata9: SATA max UDMA/133 abar m2048@0xfe900000 port 0xfe900100 irq 61
[ 0.713912] ata10: SATA max UDMA/133 abar m2048@0xfe900000 port 0xfe900180 irq 62
[ 1.027749] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.031096] ata10: SATA link down (SStatus 0 SControl 300)
[ 1.031135] ata9: SATA link down (SStatus 0 SControl 300)
[ 1.041049] usb 1-10: new full-speed USB device number 2 using xhci_hcd
[ 1.041055] usb 3-2: new full-speed USB device number 2 using xhci_hcd
[ 1.209932] usb 3-2: New USB device found, idVendor=2516, idProduct=0044
[ 1.209934] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.209935] usb 3-2: Product: MasterKeys Lite L Combo Mouse
[ 1.209936] usb 3-2: Manufacturer: Cooler Master Technology Inc.
[ 1.216759] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.242997] usbcore: registered new interface driver usbhid
[ 1.242999] usbhid: USB HID core driver
[ 1.244265] input: Cooler Master Technology Inc. MasterKeys Lite L Combo Mouse as /devices/pci0000:00/0000:00:08.1/0000:09:00.3/usb3/3-2/3-2:1.0/0003:2516:0044.0001/input/input2
[ 1.300040] hid-generic 0003:2516:0044.0001: input,hidraw0: USB HID v1.10 Keyboard [Cooler Master Technology Inc. MasterKeys Lite L Combo Mouse] on usb-0000:09:00.3-2/input0
[ 1.300319] input: Cooler Master Technology Inc. MasterKeys Lite L Combo Mouse as /devices/pci0000:00/0000:00:08.1/0000:09:00.3/usb3/3-2/3-2:1.1/0003:2516:0044.0002/input/input3
[ 1.336693] usb 3-3: new low-speed USB device number 3 using xhci_hcd
[ 1.342868] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.356776] hid-generic 0003:2516:0044.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [Cooler Master Technology Inc. MasterKeys Lite L Combo Mouse] on usb-0000:09:00.3-2/input1
[ 1.356892] hid-generic 0003:2516:0044.0003: hiddev1,hidraw2: USB HID v1.10 Device [Cooler Master Technology Inc. MasterKeys Lite L Combo Mouse] on usb-0000:09:00.3-2/input2
[ 1.359190] usb 1-10: New USB device found, idVendor=8087, idProduct=0a2a
[ 1.359192] usb 1-10: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.496002] usb 3-3: New USB device found, idVendor=2516, idProduct=0042
[ 1.496004] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.496005] usb 3-3: Product: MasterKeys Lite L Combo Keyboard(KB)
[ 1.496006] usb 3-3: Manufacturer: Cooler Master Technology Inc.
[ 1.511201] input: Cooler Master Technology Inc. MasterKeys Lite L Combo Keyboard(KB) as /devices/pci0000:00/0000:00:08.1/0000:09:00.3/usb3/3-3/3-3:1.0/0003:2516:0042.0004/input/input4
[ 1.546679] tsc: Refined TSC clocksource calibration: 3593.256 MHz
[ 1.546695] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x33cb701b428, max_idle_ns: 440795269020 ns
[ 1.546717] clocksource: Switched to clocksource tsc
[ 1.566701] hid-generic 0003:2516:0042.0004: input,hidraw3: USB HID v1.10 Keyboard [Cooler Master Technology Inc. MasterKeys Lite L Combo Keyboard(KB)] on usb-0000:09:00.3-3/input0
[ 1.575339] input: Cooler Master Technology Inc. MasterKeys Lite L Combo Keyboard(KB) as /devices/pci0000:00/0000:00:08.1/0000:09:00.3/usb3/3-3/3-3:1.1/0003:2516:0042.0005/input/input5
[ 1.630075] hid-generic 0003:2516:0042.0005: input,hiddev2,hidraw4: USB HID v1.10 Keyboard [Cooler Master Technology Inc. MasterKeys Lite L Combo Keyboard(KB)] on usb-0000:09:00.3-3/input1
[ 1.813352] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.813688] ata5.00: ATA-11: KINGSTON SUV400S37240G, 0C3J96R9, max UDMA/133
[ 1.813689] ata5.00: 468862128 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.814232] ata5.00: configured for UDMA/133
[ 1.814429] scsi 4:0:0:0: Direct-Access ATA KINGSTON SUV400S 96R9 PQ: 0 ANSI: 5
[ 1.815982] sd 4:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/224 GiB)
[ 1.815984] sd 4:0:0:0: [sda] 4096-byte physical blocks
[ 1.815997] sd 4:0:0:0: [sda] Write Protect is off
[ 1.815999] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.816028] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.818190] sda: sda1 sda2 sda3
[ 1.818744] sd 4:0:0:0: [sda] Attached SCSI disk
[ 2.126168] ata6: SATA link down (SStatus 0 SControl 300)
[ 2.219643] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 2.323794] systemd[1]: systemd 238 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN +PCRE2 default-hierarchy=hybrid)
[ 2.340225] systemd[1]: Detected architecture x86-64.
[ 2.346758] systemd[1]: Set hostname to <melvin-home>.
[ 2.425952] systemd[1]: Created slice User and Session Slice.
[ 2.425994] systemd[1]: Reached target Remote File Systems.
[ 2.426079] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 2.426125] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 2.426451] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 2.426510] systemd[1]: Listening on Journal Socket (/dev/log).
[ 2.429797] systemd[1]: Listening on udev Control Socket.
[ 2.450783] EXT4-fs (sda3): re-mounted. Opts: data=ordered
[ 2.459399] sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 2.487827] systemd-journald[268]: Received request to flush runtime journal from PID 1
[ 2.499649] systemd-journald[268]: File /var/log/journal/141b673cdc364a2d9c750cc1890eb59f/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 2.583984] rtc_cmos 00:02: RTC can wake from S4
[ 2.584321] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 2.584423] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 2.720430] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 2.720707] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 2.720710] piix4_smbus 0000:00:14.0: Using register 0x02 for SMBus port selection
[ 2.721040] cryptd: max_cpu_qlen set to 1000
[ 2.721567] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 2.726067] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver
[ 2.726205] sp5100-tco sp5100-tco: I/O address 0x0cd6 already in use
[ 2.726258] sp5100-tco: probe of sp5100-tco failed with error -16
[ 2.730013] AVX2 version of gcm_enc/dec engaged.
[ 2.730015] AES CTR mode by8 optimization enabled
[ 2.763675] Adding 8388604k swap on /dev/sda2. Priority:-2 extents:1 across:8388604k SSFS
[ 2.773386] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 2.773826] mousedev: PS/2 mouse device common for all mice
[ 2.774224] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.776411] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 2.777551] Linux agpgart interface v0.103
[ 2.778767] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 2.778771] cfg80211: failed to load regulatory.db
[ 2.792234] Bluetooth: Core ver 2.22
[ 2.792255] NET: Registered protocol family 31
[ 2.792256] Bluetooth: HCI device and connection manager initialized
[ 2.792260] Bluetooth: HCI socket layer initialized
[ 2.792263] Bluetooth: L2CAP socket layer initialized
[ 2.792269] Bluetooth: SCO socket layer initialized
[ 2.797792] r8169 0000:08:00.0 eth0: RTL8168g/8111g at 0x00000000ec8bfd2b, e0:d5:5e:64:30:7f, XID 0c000800 IRQ 63
[ 2.797795] r8169 0000:08:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 2.798206] Intel(R) Wireless WiFi driver for Linux
[ 2.798207] Copyright(c) 2003- 2015 Intel Corporation
[ 2.798270] iwlwifi 0000:06:00.0: enabling device (0000 -> 0002)
[ 2.807313] iwlwifi 0000:06:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm
[ 2.808455] r8169 0000:08:00.0 enp8s0: renamed from eth0
[ 2.808649] snd_hda_intel 0000:09:00.1: Handle vga_switcheroo audio client
[ 2.832315] usbcore: registered new interface driver btusb
[ 2.839466] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:08.1/0000:09:00.1/sound/card0/input7
[ 2.842169] input: HD-Audio Generic HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:08.1/0000:09:00.1/sound/card0/input8
[ 2.842232] input: HD-Audio Generic HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:08.1/0000:09:00.1/sound/card0/input9
[ 2.842396] input: HD-Audio Generic HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:08.1/0000:09:00.1/sound/card0/input10
[ 2.842450] input: HD-Audio Generic HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:08.1/0000:09:00.1/sound/card0/input11
[ 2.842515] input: HD-Audio Generic HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:08.1/0000:09:00.1/sound/card0/input12
[ 2.844987] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC1220: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 2.844992] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 2.844995] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 2.844996] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 2.844997] snd_hda_codec_realtek hdaudioC1D0: dig-out=0x1e/0x0
[ 2.844998] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 2.845000] snd_hda_codec_realtek hdaudioC1D0: Front Mic=0x19
[ 2.845001] snd_hda_codec_realtek hdaudioC1D0: Rear Mic=0x18
[ 2.845003] snd_hda_codec_realtek hdaudioC1D0: Line=0x1a
[ 2.853697] kvm: disabled by bios
[ 2.857012] Bluetooth: hci0: read Intel version: 370810011003110e25
[ 2.857014] Bluetooth: hci0: Intel device is already patched. patch num: 25
[ 2.862711] MCE: In-kernel MCE decoding enabled.
[ 2.876799] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:08.1/0000:09:00.6/sound/card1/input13
[ 2.876887] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:08.1/0000:09:00.6/sound/card1/input14
[ 2.876946] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:08.1/0000:09:00.6/sound/card1/input15
[ 2.877005] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:08.1/0000:09:00.6/sound/card1/input16
[ 2.877058] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:08.1/0000:09:00.6/sound/card1/input17
[ 2.877108] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:08.1/0000:09:00.6/sound/card1/input18
[ 2.877170] input: HD-Audio Generic Line Out Side as /devices/pci0000:00/0000:00:08.1/0000:09:00.6/sound/card1/input19
[ 2.877231] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:08.1/0000:09:00.6/sound/card1/input20
[ 2.985099] kvm: disabled by bios
[ 2.988929] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 3165, REV=0x210
[ 3.006702] iwlwifi 0000:06:00.0: base HW address: 9c:da:3e:a3:da:f4
[ 3.088302] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[ 3.088825] thermal thermal_zone0: failed to read out thermal zone (-61)
[ 3.090463] iwlwifi 0000:06:00.0 wlp6s0: renamed from wlan0
[ 3.130541] [drm] amdgpu kernel modesetting enabled.
[ 3.153913] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.153915] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[ 3.153916] Bluetooth: BNEP filters: protocol multicast
[ 3.153921] Bluetooth: BNEP socket layer initialized
[ 3.162222] Parsing CRAT table with 1 nodes
[ 3.162233] Creating topology SYSFS entries
[ 3.162259] Topology: Add APU node [0x0:0x0]
[ 3.162260] Finished initializing topology
[ 3.162289] kfd kfd: Initialized module
[ 3.162481] checking generic (e0000000 300000) vs hw (e0000000 10000000)
[ 3.162482] fb: switching to amdgpudrmfb from EFI VGA
[ 3.162519] Console: switching to colour dummy device 80x25
[ 3.162805] [drm] initializing kernel modesetting (RAVEN 0x1002:0x15DD 0x1458:0xD000 0xC6).
[ 3.162818] [drm] register mmio base: 0xFE500000
[ 3.162819] [drm] register mmio size: 524288
[ 3.163368] [drm] probing gen 2 caps for device 1022:15db = 700d03/e
[ 3.163372] [drm] probing mlw for device 1022:15db = 700d03
[ 3.163583] [drm] VCN decode is enabled in VM mode
[ 3.163584] [drm] VCN encode is enabled in VM mode
[ 3.188341] [drm] BIOS signature incorrect 0 0
[ 3.188368] ATOM BIOS: 113-RAVEN-106
[ 3.188394] [drm] vm size is 262144 GB, 4 levels, block size is 9-bit, fragment size is 9-bit
[ 3.188399] amdgpu 0000:09:00.0: VRAM: 1024M 0x000000F400000000 - 0x000000F43FFFFFFF (1024M used)
[ 3.188400] amdgpu 0000:09:00.0: GTT: 1024M 0x000000F500000000 - 0x000000F53FFFFFFF
[ 3.188403] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 3.188404] [drm] RAM width 64bits UNKNOWN
[ 3.188459] [TTM] Zone kernel: Available graphics memory: 3574876 kiB
[ 3.188460] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 3.188460] [TTM] Initializing pool allocator
[ 3.188463] [TTM] Initializing DMA pool allocator
[ 3.188480] [drm] amdgpu: 1024M of VRAM memory ready
[ 3.188482] [drm] amdgpu: 3072M of GTT memory ready.
[ 3.188495] [drm] GART: num cpu pages 262144, num gpu pages 262144
[ 3.188678] [drm] PCIE GART of 1024M enabled (table at 0x000000F400800000).
[ 3.193135] [drm] use_doorbell being set to: [true]
[ 3.194471] [drm] Found VCN firmware Version: 1.73 Family ID: 18
[ 3.323902] [drm:construct [amdgpu]] *ERROR* construct: Invalid Connector ObjectID from Adapter Service for connector index:1! type 0 expected 3
[ 3.323952] [drm:construct [amdgpu]] *ERROR* construct: Invalid Connector ObjectID from Adapter Service for connector index:2! type 0 expected 3
[ 3.328414] [drm] Display Core initialized with v3.1.27!
[ 3.353609] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.353611] [drm] Driver supports precise vblank timestamp query.
[ 3.376626] [drm] VCN decode and encode initialized successfully.
[ 3.385526] [drm] fb mappable at 0xE1000000
[ 3.385527] [drm] vram apper at 0xE0000000
[ 3.385528] [drm] size 8294400
[ 3.385528] [drm] fb depth is 24
[ 3.385529] [drm] pitch is 7680
[ 3.385605] fbcon: amdgpudrmfb (fb0) is primary device
[ 3.401407] random: crng init done
[ 3.416191] Console: switching to colour frame buffer device 240x67
[ 3.435993] amdgpu 0000:09:00.0: fb0: amdgpudrmfb frame buffer device
[ 3.444669] IPv6: ADDRCONF(NETDEV_UP): enp8s0: link is not ready
[ 3.453443] amdgpu 0000:09:00.0: ring 0(gfx) uses VM inv eng 4 on hub 0
[ 3.453445] amdgpu 0000:09:00.0: ring 1(comp_1.0.0) uses VM inv eng 5 on hub 0
[ 3.453446] amdgpu 0000:09:00.0: ring 2(comp_1.1.0) uses VM inv eng 6 on hub 0
[ 3.453448] amdgpu 0000:09:00.0: ring 3(comp_1.2.0) uses VM inv eng 7 on hub 0
[ 3.453449] amdgpu 0000:09:00.0: ring 4(comp_1.3.0) uses VM inv eng 8 on hub 0
[ 3.453450] amdgpu 0000:09:00.0: ring 5(comp_1.0.1) uses VM inv eng 9 on hub 0
[ 3.453452] amdgpu 0000:09:00.0: ring 6(comp_1.1.1) uses VM inv eng 10 on hub 0
[ 3.453453] amdgpu 0000:09:00.0: ring 7(comp_1.2.1) uses VM inv eng 11 on hub 0
[ 3.453454] amdgpu 0000:09:00.0: ring 8(comp_1.3.1) uses VM inv eng 12 on hub 0
[ 3.453455] amdgpu 0000:09:00.0: ring 9(kiq_2.1.0) uses VM inv eng 13 on hub 0
[ 3.453457] amdgpu 0000:09:00.0: ring 10(sdma0) uses VM inv eng 4 on hub 1
[ 3.453458] amdgpu 0000:09:00.0: ring 11(vcn_dec) uses VM inv eng 5 on hub 1
[ 3.453459] amdgpu 0000:09:00.0: ring 12(vcn_enc0) uses VM inv eng 6 on hub 1
[ 3.453461] amdgpu 0000:09:00.0: ring 13(vcn_enc1) uses VM inv eng 7 on hub 1
[ 3.457540] [drm] Initialized amdgpu 3.23.0 20150101 for 0000:09:00.0 on minor 0
[ 3.492649] r8169 0000:08:00.0 enp8s0: link down
[ 3.492650] r8169 0000:08:00.0 enp8s0: link down
[ 3.492736] IPv6: ADDRCONF(NETDEV_UP): enp8s0: link is not ready
[ 3.495466] IPv6: ADDRCONF(NETDEV_UP): wlp6s0: link is not ready
[ 4.080227] systemd-journald[268]: File /var/log/journal/141b673cdc364a2d9c750cc1890eb59f/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
[ 4.917181] fuse init (API version 7.26)
[ 5.903454] Bluetooth: RFCOMM TTY layer initialized
[ 5.903460] Bluetooth: RFCOMM socket layer initialized
[ 5.903468] Bluetooth: RFCOMM ver 1.11
[ 6.286991] r8169 0000:08:00.0 enp8s0: link up
[ 6.287000] IPv6: ADDRCONF(NETDEV_CHANGE): enp8s0: link becomes ready
[ 6.639579] r8169 0000:08:00.0 enp8s0: link down
[ 6.955971] rfkill: input handler disabled
[ 16.241906] r8169 0000:08:00.0 enp8s0: link upOffline
#4 2018-04-22 22:47:02
- MelvIsntNormal
- Member
- Registered: 2018-04-22
- Posts: 12
Re: Random black screen and freezing issues (AMD Ryzen 2400G)
So it happened again, but this time I made sure to check journalctl and found something that looks important:
Apr 22 23:21:34 melvin-home steam.desktop[6075]: process 6264: arguments to dbus_connection_unref() were incorrect, assertion "connection->generation == _dbus_current_generation" failed in file ../../dbus/dbus-connection.c line 2794.
Apr 22 23:21:34 melvin-home steam.desktop[6075]: This is normally a bug in some application using the D-Bus library.
Apr 22 23:21:43 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:43 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a13000 from 27
Apr 22 23:21:43 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00501031
Apr 22 23:21:43 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a0e000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a14000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a0d000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a0a000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a0b000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a0b000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a0a000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a13000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: [gfxhub] VMC page fault (src_id:0 ring:24 vmid:5 pas_id:0)
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: at page 0x0000000101a15000 from 27
Apr 22 23:21:44 melvin-home kernel: amdgpu 0000:09:00.0: VM_L2_PROTECTION_FAULT_STATUS:0x00000000
Apr 22 23:21:54 melvin-home kernel: [drm:amdgpu_job_timedout [amdgpu]] *ERROR* ring gfx timeout, last signaled seq=265297, last emitted seq=265299
Apr 22 23:21:54 melvin-home kernel: [drm] IP block:psp is hung!
Apr 22 23:21:54 melvin-home kernel: [drm] GPU recovery disabled.The first two lines were repeated ad infinitum (seemingly anyway, sometimes it referred to line 2656). Some quick Googling of the pagefault issue brings me to this bug report from last December. It's been fixed according to the tracker, and I'm definitely on the latest version. I found it intriguing that it was VEGA graphics involved again; looks like our cases are even more related since the Ryzen 2400G has VEGA integrated graphics.
I'm also wondering about the last line from journalctl. Is GPU recovery what it says on the tin? How can I enable it? I'll look into this more, again I would really appreciate soime help with this.
Offline
#5 2018-04-22 23:16:49
- loqs
- Member
- Registered: 2014-03-06
- Posts: 18,055
Re: Random black screen and freezing issues (AMD Ryzen 2400G)
https://bugs.freedesktop.org/show_bug.cgi?id=104817 seems similar.
What is the output of `systool -vm amdgpu`?
Offline
#6 2018-04-23 08:15:18
- MelvIsntNormal
- Member
- Registered: 2018-04-22
- Posts: 12
Re: Random black screen and freezing issues (AMD Ryzen 2400G)
loqs wrote:
What is the output of `systool -vm amdgpu`?
Module = "amdgpu"
Attributes:
coresize = "3129344"
initsize = "0"
initstate = "live"
refcnt = "20"
srcversion = "243E0B4DFBE0DEB30BF70CB"
taint = ""
uevent = <store method only>
Parameters:
aspm = "-1"
audio = "-1"
bapm = "-1"
benchmark = "0"
cg_mask = "4294967295"
cik_support = "0"
cntl_sb_buf_per_se = "0"
compute_multipipe = "-1"
dc = "-1"
dc_log = "0"
deep_color = "0"
direct_gma_size = "0"
disable_cu = "(null)"
disp_priority = "0"
dpm = "-1"
exp_hw_support = "0"
fw_load_type = "-1"
gpu_recovery = "-1"
hw_i2c = "0"
ip_block_mask = "4294967295"
job_hang_limit = "0"
lbpw = "-1"
lockup_timeout = "10000"
msi = "-1"
ngg = "0"
no_evict = "0"
param_buf_per_se = "0"
pcie_gen2 = "-1"
pcie_gen_cap = "0"
pcie_lane_cap = "0"
pg_mask = "4294967295"
pos_buf_per_se = "0"
ppfeaturemask = "4294967295"
prim_buf_per_se = "0"
runpm = "-1"
sched_hw_submission = "2"
sched_jobs = "32"
sdma_phase_quantum = "32"
si_support = "0"
test = "0"
virtual_display = "(null)"
vis_vramlimit = "0"
vm_block_size = "-1"
vm_debug = "0"
vm_fault_stop = "0"
vm_fragment_size = "-1"
vm_size = "-1"
vm_update_mode = "-1"
vram_page_split = "512"
Sections:Offline
#7 2018-11-12 14:54:39
- Bleistift
- Member
- Registered: 2018-02-22
- Posts: 3
Re: Random black screen and freezing issues (AMD Ryzen 2400G)
You still have that issue? Have you installed a recent kernel in the meantime?
I read somewhere, using boot option amdgpu.lockup_timeout=0 might help with system freezes.
I use a mobile Ryzen system, despite using recent kernel 4.19.0 I also suffer from random freezes, but it´s much better now than some months ago.
And install latest BIOS!
Offline