Make SD card reader work

akjanik · 2018-11-17 11:07:36

My PC has a built in case SD card reader. It works when I boot on other HDD with Windows.

I am pretty sure it is this one, since this entry disappears when I remove SD card.

Disk /dev/sdd: 29.1 GiB, 31243370496 bytes, 61022208 sectors
Disk model: Storage Device  
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00000000

Device     Boot Start      End  Sectors  Size Id Type
/dev/sdd1        8192 61022207 61014016 29.1G  c W95 FAT32 (LBA)

some

dmesg

:

[  953.486847] br-f041ea28c314: port 1(veth0c9154b) entered disabled state
[  993.187371] usb 1-14: new high-speed USB device number 18 using xhci_hcd
[  993.351508] usb 1-14: New USB device found, idVendor=14cd, idProduct=125d, bcdDevice= 1.00
[  993.351513] usb 1-14: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[  993.351516] usb 1-14: Product: Mass Storage Device
[  993.351518] usb 1-14: Manufacturer: Generic
[  993.351520] usb 1-14: SerialNumber: 125D20140310
[  993.358938] usb-storage 1-14:1.0: USB Mass Storage device detected
[  993.359199] scsi host9: usb-storage 1-14:1.0
[  994.386938] scsi 9:0:0:0: Direct-Access     Mass     Storage Device        PQ: 0 ANSI: 0 CCS
[  994.387773] sd 9:0:0:0: [sdd] 61022208 512-byte logical blocks: (31.2 GB/29.1 GiB)
[  994.387898] sd 9:0:0:0: [sdd] Write Protect is off
[  994.387900] sd 9:0:0:0: [sdd] Mode Sense: 03 00 00 00
[  994.388027] sd 9:0:0:0: [sdd] No Caching mode page found
[  994.388030] sd 9:0:0:0: [sdd] Assuming drive cache: write through
[  994.390231]  sdd: sdd1
[  994.391493] sd 9:0:0:0: [sdd] Attached SCSI removable disk
[ 1013.394418] br-f041ea28c314: port 1(veth88a3df3) entered blocking state
[ 1013.394423] br-f041ea28c314: port 1(veth88a3df3) entered disabled state
[ 1013.394532] device veth88a3df3 entered promiscuous mode
[ 1013.394563] kauditd_printk_skb: 26 callbacks suppressed
[ 1013.394565] audit: type=1700 audit(1542452065.342:410): dev=veth88a3df3 prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 1013.394668] audit: type=1300 audit(1542452065.342:410): arch=c000003e syscall=44 success=yes exit=40 a0=c a1=c00074af00 a2=28 a3=0 items=0 ppid=1 pid=669 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 1013.394673] audit: type=1327 audit(1542452065.342:410): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F
[ 1013.394737] IPv6: ADDRCONF(NETDEV_UP): veth88a3df3: link is not ready
[ 1013.394741] br-f041ea28c314: port 1(veth88a3df3) entered blocking state
[ 1013.394744] br-f041ea28c314: port 1(veth88a3df3) entered forwarding state
[ 1013.395321] br-f041ea28c314: port 1(veth88a3df3) entered disabled state
[ 1013.536643] audit: type=1325 audit(1542452065.482:411): table=filter family=2 entries=0
[ 1013.536646] audit: type=1300 audit(1542452065.482:411): arch=c000003e syscall=55 success=yes exit=0 a0=4 a1=0 a2=40 a3=7ffe8d4a2930 items=0 ppid=6566 pid=6584 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/bin/xtables-legacy-multi" key=(null)
[ 1013.536648] audit: type=1327 audit(1542452065.482:411): proctitle=2F7573722F62696E2F69707461626C6573002D2D77616974002D4C002D6E
[ 1013.538761] audit: type=1325 audit(1542452065.485:412): table=nat family=2 entries=0
[ 1013.538763] audit: type=1300 audit(1542452065.485:412): arch=c000003e syscall=55 success=yes exit=0 a0=4 a1=0 a2=40 a3=7ffe883a6d30 items=0 ppid=6566 pid=6586 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/bin/xtables-legacy-multi" key=(null)
[ 1013.538765] audit: type=1327 audit(1542452065.485:412): proctitle=2F7573722F62696E2F69707461626C6573002D2D77616974002D74006E6174002D43004F5554505554002D64003132372E302E302E3131002D6A00444F434B45525F4F5554505554
[ 1013.541088] audit: type=1325 audit(1542452065.488:413): table=nat family=2 entries=5
[ 1013.584255] eth0: renamed from veth30b1f28
[ 1013.610844] IPv6: ADDRCONF(NETDEV_CHANGE): veth88a3df3: link becomes ready
[ 1013.610869] br-f041ea28c314: port 1(veth88a3df3) entered blocking state
[ 1013.610870] br-f041ea28c314: port 1(veth88a3df3) entered forwarding state
[ 1015.851857] br-f041ea28c314: port 1(veth88a3df3) entered disabled state
[ 1015.851949] veth30b1f28: renamed from eth0
[ 1015.938303] br-f041ea28c314: port 1(veth88a3df3) entered disabled state
[ 1015.940824] device veth88a3df3 left promiscuous mode
[ 1015.940832] br-f041ea28c314: port 1(veth88a3df3) entered disabled state
[ 1075.850445] br-f041ea28c314: port 1(vethf88a93b) entered blocking state
[ 1075.850449] br-f041ea28c314: port 1(vethf88a93b) entered disabled state
[ 1075.850525] device vethf88a93b entered promiscuous mode
[ 1075.850702] IPv6: ADDRCONF(NETDEV_UP): vethf88a93b: link is not ready
[ 1075.850706] br-f041ea28c314: port 1(vethf88a93b) entered blocking state
[ 1075.850709] br-f041ea28c314: port 1(vethf88a93b) entered forwarding state
[ 1075.851133] br-f041ea28c314: port 1(vethf88a93b) entered disabled state
[ 1075.851447] kauditd_printk_skb: 26 callbacks suppressed
[ 1075.851449] audit: type=1700 audit(1542452127.799:422): dev=vethf88a93b prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 1075.851456] audit: type=1300 audit(1542452127.799:422): arch=c000003e syscall=44 success=yes exit=40 a0=c a1=c00074a570 a2=28 a3=0 items=0 ppid=1 pid=669 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 1075.851461] audit: type=1327 audit(1542452127.799:422): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F
[ 1075.971503] audit: type=1325 audit(1542452127.919:423): table=filter family=2 entries=0
[ 1075.971507] audit: type=1300 audit(1542452127.919:423): arch=c000003e syscall=55 success=yes exit=0 a0=4 a1=0 a2=40 a3=7ffd6f1c9550 items=0 ppid=6734 pid=6752 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/bin/xtables-legacy-multi" key=(null)
[ 1075.971509] audit: type=1327 audit(1542452127.919:423): proctitle=2F7573722F62696E2F69707461626C6573002D2D77616974002D4C002D6E
[ 1075.973913] audit: type=1325 audit(1542452127.922:424): table=nat family=2 entries=0
[ 1075.973916] audit: type=1300 audit(1542452127.922:424): arch=c000003e syscall=55 success=yes exit=0 a0=4 a1=0 a2=40 a3=7ffdf46293f0 items=0 ppid=6734 pid=6754 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/bin/xtables-legacy-multi" key=(null)
[ 1075.973918] audit: type=1327 audit(1542452127.922:424): proctitle=2F7573722F62696E2F69707461626C6573002D2D77616974002D74006E6174002D43004F5554505554002D64003132372E302E302E3131002D6A00444F434B45525F4F5554505554
[ 1075.975122] audit: type=1325 audit(1542452127.922:425): table=nat family=2 entries=5
[ 1076.030114] eth0: renamed from vethaf23a09
[ 1076.064157] IPv6: ADDRCONF(NETDEV_CHANGE): vethf88a93b: link becomes ready
[ 1076.064203] br-f041ea28c314: port 1(vethf88a93b) entered blocking state
[ 1076.064205] br-f041ea28c314: port 1(vethf88a93b) entered forwarding state
[ 1078.288182] br-f041ea28c314: port 1(vethf88a93b) entered disabled state
[ 1078.288225] vethaf23a09: renamed from eth0
[ 1078.348547] br-f041ea28c314: port 1(vethf88a93b) entered disabled state
[ 1078.349986] device vethf88a93b left promiscuous mode
[ 1078.349993] br-f041ea28c314: port 1(vethf88a93b) entered disabled state
[ 1138.286532] br-f041ea28c314: port 1(veth14b3916) entered blocking state
[ 1138.286559] br-f041ea28c314: port 1(veth14b3916) entered disabled state
[ 1138.286670] device veth14b3916 entered promiscuous mode
[ 1138.286707] kauditd_printk_skb: 26 callbacks suppressed
[ 1138.286710] audit: type=1700 audit(1542452190.236:434): dev=veth14b3916 prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 1138.286903] audit: type=1300 audit(1542452190.236:434): arch=c000003e syscall=44 success=yes exit=40 a0=c a1=c000c62780 a2=28 a3=0 items=0 ppid=1 pid=669 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 1138.286909] audit: type=1327 audit(1542452190.236:434): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F
[ 1138.286973] IPv6: ADDRCONF(NETDEV_UP): veth14b3916: link is not ready
[ 1138.413597] audit: type=1325 audit(1542452190.362:435): table=filter family=2 entries=0
[ 1138.413599] audit: type=1300 audit(1542452190.362:435): arch=c000003e syscall=55 success=yes exit=0 a0=4 a1=0 a2=40 a3=7fff6505f340 items=0 ppid=6864 pid=6881 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/bin/xtables-legacy-multi" key=(null)
[ 1138.413601] audit: type=1327 audit(1542452190.362:435): proctitle=2F7573722F62696E2F69707461626C6573002D2D77616974002D4C002D6E
[ 1138.416437] audit: type=1325 audit(1542452190.366:436): table=nat family=2 entries=0
[ 1138.416441] audit: type=1300 audit(1542452190.366:436): arch=c000003e syscall=55 success=yes exit=0 a0=4 a1=0 a2=40 a3=7ffc94529220 items=0 ppid=6864 pid=6883 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/bin/xtables-legacy-multi" key=(null)
[ 1138.416443] audit: type=1327 audit(1542452190.366:436): proctitle=2F7573722F62696E2F69707461626C6573002D2D77616974002D74006E6174002D43004F5554505554002D64003132372E302E302E3131002D6A00444F434B45525F4F5554505554
[ 1138.418003] audit: type=1325 audit(1542452190.366:437): table=nat family=2 entries=5
[ 1138.476907] eth0: renamed from veth1699d1b
[ 1138.503638] IPv6: ADDRCONF(NETDEV_CHANGE): veth14b3916: link becomes ready
[ 1138.503677] br-f041ea28c314: port 1(veth14b3916) entered blocking state
[ 1138.503679] br-f041ea28c314: port 1(veth14b3916) entered forwarding state
[ 1140.719332] br-f041ea28c314: port 1(veth14b3916) entered disabled state
[ 1140.719378] veth1699d1b: renamed from eth0
[ 1140.788111] br-f041ea28c314: port 1(veth14b3916) entered disabled state
[ 1140.790583] device veth14b3916 left promiscuous mode
[ 1140.790605] br-f041ea28c314: port 1(veth14b3916) entered disabled state
[ 1147.543886] usb 1-14: reset high-speed USB device number 18 using xhci_hcd
[ 1149.748131]  sdd: sdd1

I have tried so far:

udisksctl mount -b /dev/sdd
Object /org/freedesktop/UDisks2/block_devices/sdd is not a mountable filesystem.

and

sudo mount /dev/sdd1/ /media/sdcard/
mount: /media/sdcard: special device /dev/sdd1/ does not exist (a path prefix is not a directory).

I installed gnome disks utility and it sees the device, but I see no way to access my photos right now.

Slithery · 2018-11-17 11:11:09

As the error messages state you just have some typos. Those commands should be...

udisksctl mount -b /dev/sdd1

or

sudo mount /dev/sdd1 /media/sdcard/

akjanik · 2018-11-17 15:59:06

Still...

udisksctl mount -b /dev/sdd1
Object /org/freedesktop/UDisks2/block_devices/sdd1 is not a mountable filesystem.

Using mount command worked, however, I had to do it with `sudo`, and had to type password while unmounting.
How can I set things up so I just insert SD card into reader and browse files in the file manager without terminal/password etc.? I may forget it, moreover, am I guaranteed that this will always be `sdd1`?

cirrus · 2018-11-17 19:59:24

akjanik wrote:

am I guaranteed that this will always be `sdd1`?

No use UUID in /etc/fstab if the SD card is permanently inserted.

akjanik · 2018-11-18 09:56:15

It is not (I use it in my camera most of the time), and it may be a different card.

cirrus · 2018-11-18 14:24:53

It *should* be readable & writable by user, FAIK the card reader needs no separate drivers or firmware, only time I have such issues is after a kernel update where the new modules are not yet loaded, the few SD cards I have are formatted in Android and my file manager on Arch (pcmanfm) see’s them without manually mounting, have a look in your file managers prefs.

seth · 2018-11-18 14:41:51

Object /org/freedesktop/UDisks2/block_devices/sdd1 is not a mountable filesystem.

???

sudo file -s /dev/sdd1

akjanik · 2018-11-21 18:45:30

Sorry for the late reply.

[adam@adam ~]$ sudo file -s /dev/sdd1
/dev/sdd1: data

I format SD card in my camera, when first inserted, it asks for format, to make it work with device.

seth · 2018-11-21 21:30:58

Yeah, that's simply not some known file system. You hopefully do not have valuable data exclusively on that card, because if it had been formatted to a FS before, that's mostly gone (see https://wiki.archlinux.org/index.php/File_recovery ) and also there's a good chance that the card is toast.

Arch Linux

#1 2018-11-17 11:07:36

Make SD card reader work

#2 2018-11-17 11:11:09

Re: Make SD card reader work

#3 2018-11-17 15:59:06

Re: Make SD card reader work

#4 2018-11-17 19:59:24

Re: Make SD card reader work

#5 2018-11-18 09:56:15

Re: Make SD card reader work

#6 2018-11-18 14:24:53

Re: Make SD card reader work

#7 2018-11-18 14:41:51

Re: Make SD card reader work

#8 2018-11-21 18:45:30

Re: Make SD card reader work

#9 2018-11-21 21:30:58

Re: Make SD card reader work

Board footer