You are not logged in.
Hi,
I've changed to 2.1 speakers and I've search in Internet to configure pulseaudio.
These are the changes I did in /etc/pulse/daemon.conf:
$ diff /etc/pulse/daemon.conf /etc/pulse/daemon.conf.old
resample-method = soxr-mq | ; resample-method = speex-float-1
enable-lfe-remixing = yes | ; enable-lfe-remixing = no
lfe-crossover-freq = 170 | ; lfe-crossover-freq = 0
default-sample-format = float32le | ; default-sample-format = s16le
default-sample-rate = 44100 | ; default-sample-rate = 44100
alternate-sample-rate = 48000 | ; alternate-sample-rate = 48000
default-sample-channels = 3 | ; default-sample-channels = 2
default-channel-map = front-left,front-right,lfe | ; default-channel-map = front-left,front-right
I don't know how to check if pulseaudio is correctly loading those changes but when I execute 'pacmd list-sinks' shows this:
1 sink(s) available.
* index: 0
name: <alsa_output.pci-0000_00_1f.3.analog-stereo>
driver: <module-alsa-card.c>
flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY DYNAMIC_LATENCY
state: RUNNING
suspend cause: (none)
priority: 9039
volume: front-left: 16634 / 25% / -35,73 dB, front-right: 16634 / 25% / -35,73 dB
balance 0,00
base volume: 65536 / 100% / 0,00 dB
volume steps: 65537
muted: no
current latency: 430,85 ms
max request: 158 KiB
max rewind: 158 KiB
monitor source: 1
sample spec: s32le 2ch 44100Hz
channel map: front-left,front-right
Estéreo
used by: 1
linked by: 1
configured latency: 460,00 ms; range is 0,50 .. 2000,00 ms
card: 1 <alsa_card.pci-0000_00_1f.3>
module: 7
properties:
alsa.resolution_bits = "32"
device.api = "alsa"
device.class = "sound"
alsa.class = "generic"
alsa.subclass = "generic-mix"
alsa.name = "ALC662 rev3 Analog"
alsa.id = "ALC662 rev3 Analog"
alsa.subdevice = "0"
alsa.subdevice_name = "subdevice #0"
alsa.device = "0"
alsa.card = "0"
alsa.card_name = "HDA Intel PCH"
alsa.long_card_name = "HDA Intel PCH at 0xdf120000 irq 128"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:00:1f.3"
sysfs.path = "/devices/pci0000:00/0000:00:1f.3/sound/card0"
device.bus = "pci"
device.vendor.id = "8086"
device.vendor.name = "Intel Corporation"
device.product.id = "a170"
device.product.name = "Sunrise Point-H HD Audio"
device.form_factor = "internal"
device.string = "front:0"
device.buffering.buffer_size = "705600"
device.buffering.fragment_size = "352800"
device.access_mode = "mmap+timer"
device.profile.name = "analog-stereo"
device.profile.description = "Estéreo Analógico"
device.description = "Audio Interno Estéreo Analógico"
alsa.mixer_name = "Realtek ALC662 rev3"
alsa.components = "HDA:10ec0662,10199c7d,00100300 HDA:8086280b,80860101,00100000"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
ports:
analog-output-lineout: Line Out (priority 9900, latency offset 0 usec, available: yes)
properties:
analog-output-headphones: Auriculares analógicos (priority 9000, latency offset 0 usec, available: no)
properties:
device.icon_name = "audio-headphones"
active port: <analog-output-lineout>
In 'sample spec' shows 's32le 2ch 44100Hz', these are not the same values in daemon.conf. Which makes me think the rest of the values aren't being respected either. Am I checking with the wrong command?
Thanks.
Offline
Surround profiles are usually available as, well, specific profiles. Shot in the dark:
pacmd set-card-profile alsa_output.pci-0000_00_1f.3 output:analog-surround-21+input:analog-stereo
(use the available profiles from pacmd list-cards if that one turns out to be incorrect) the default-channel-map and sample channels are usually only relevant on sinks that do not themselves provide that information, nearly every udev-detected ALSA card does so however, so the channel maps are split up into profiles, irrespective of the channel-map that is configured.
Similarly the sample spec will be driven by what you are actually playing. It doesn't make sense to apply a CPU intensive resampling effort if the actual source you are playing back advertises a different format that is compatible with your device. So what you are configuring in that regard is a suggestion, should an application request a stream that is incompatible with the capabilities of your device, pulseaudio will instead open the device with your specified parameters and resample accordingly.
Due to that it might also be relevant what you are actually playing, what's
pacmd list-sink-inputs
during this?
Last edited by V1del (2018-11-30 16:48:23)
Offline
'pacmd list-cards' doesn't show any 2.1 profile:
index: 1
name: <alsa_card.pci-0000_00_1f.3>
driver: <module-alsa-card.c>
owner module: 7
properties:
alsa.card = "0"
alsa.card_name = "HDA Intel PCH"
alsa.long_card_name = "HDA Intel PCH at 0xdf120000 irq 128"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:00:1f.3"
sysfs.path = "/devices/pci0000:00/0000:00:1f.3/sound/card0"
device.bus = "pci"
device.vendor.id = "8086"
device.vendor.name = "Intel Corporation"
device.product.id = "a170"
device.product.name = "Sunrise Point-H HD Audio"
device.form_factor = "internal"
device.string = "0"
device.description = "Audio Interno"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
profiles:
input:analog-stereo: Estéreo Analógico Input (priority 65, available: no)
output:analog-stereo: Estéreo Analógico Output (priority 6500, available: unknown)
output:analog-stereo+input:analog-stereo: Estéreo Analógico.Duplex (priority 6565, available: unknown)
output:hdmi-stereo: Digital Stereo (HDMI) Output (priority 5900, available: unknown)
output:hdmi-stereo+input:analog-stereo: Digital Stereo (HDMI) Output + Estéreo Analógico Input (priority 5965, available: unknown)
output:hdmi-stereo-extra1: Digital Stereo (HDMI 2) Output (priority 5700, available: no)
output:hdmi-stereo-extra1+input:analog-stereo: Digital Stereo (HDMI 2) Output + Estéreo Analógico Input (priority 5765, available: no)
output:hdmi-surround-extra1: Digital Surround 5.1 (HDMI 2) Output (priority 600, available: no)
output:hdmi-surround-extra1+input:analog-stereo: Digital Surround 5.1 (HDMI 2) Output + Estéreo Analógico Input (priority 665, available: no)
output:hdmi-surround71-extra1: Digital Surround 7.1 (HDMI 2) Output (priority 600, available: no)
output:hdmi-surround71-extra1+input:analog-stereo: Digital Surround 7.1 (HDMI 2) Output + Estéreo Analógico Input (priority 665, available: no)
output:hdmi-stereo-extra2: Digital Stereo (HDMI 3) Output (priority 5700, available: no)
output:hdmi-stereo-extra2+input:analog-stereo: Digital Stereo (HDMI 3) Output + Estéreo Analógico Input (priority 5765, available: no)
output:hdmi-surround-extra2: Digital Surround 5.1 (HDMI 3) Output (priority 600, available: no)
output:hdmi-surround-extra2+input:analog-stereo: Digital Surround 5.1 (HDMI 3) Output + Estéreo Analógico Input (priority 665, available: no)
output:hdmi-surround71-extra2: Digital Surround 7.1 (HDMI 3) Output (priority 600, available: no)
output:hdmi-surround71-extra2+input:analog-stereo: Digital Surround 7.1 (HDMI 3) Output + Estéreo Analógico Input (priority 665, available: no)
output:hdmi-stereo-extra3: Digital Stereo (HDMI 4) Output (priority 5700, available: no)
output:hdmi-stereo-extra3+input:analog-stereo: Digital Stereo (HDMI 4) Output + Estéreo Analógico Input (priority 5765, available: no)
output:hdmi-surround-extra3: Digital Surround 5.1 (HDMI 4) Output (priority 600, available: no)
output:hdmi-surround-extra3+input:analog-stereo: Digital Surround 5.1 (HDMI 4) Output + Estéreo Analógico Input (priority 665, available: no)
output:hdmi-surround71-extra3: Digital Surround 7.1 (HDMI 4) Output (priority 600, available: no)
output:hdmi-surround71-extra3+input:analog-stereo: Digital Surround 7.1 (HDMI 4) Output + Estéreo Analógico Input (priority 665, available: no)
output:hdmi-stereo-extra4: Digital Stereo (HDMI 5) Output (priority 5700, available: no)
output:hdmi-stereo-extra4+input:analog-stereo: Digital Stereo (HDMI 5) Output + Estéreo Analógico Input (priority 5765, available: no)
output:hdmi-surround-extra4: Digital Surround 5.1 (HDMI 5) Output (priority 600, available: no)
output:hdmi-surround-extra4+input:analog-stereo: Digital Surround 5.1 (HDMI 5) Output + Estéreo Analógico Input (priority 665, available: no)
output:hdmi-surround71-extra4: Digital Surround 7.1 (HDMI 5) Output (priority 600, available: no)
output:hdmi-surround71-extra4+input:analog-stereo: Digital Surround 7.1 (HDMI 5) Output + Estéreo Analógico Input (priority 665, available: no)
off: Apagado (priority 0, available: unknown)
active profile: <output:analog-stereo+input:analog-stereo>
sinks:
alsa_output.pci-0000_00_1f.3.analog-stereo/#0: Audio Interno Estéreo Analógico
sources:
alsa_output.pci-0000_00_1f.3.analog-stereo.monitor/#1: Monitor of Audio Interno Estéreo Analógico
alsa_input.pci-0000_00_1f.3.analog-stereo/#2: Audio Interno Estéreo Analógico
ports:
analog-input-front-mic: Front Microphone (priority 8500, latency offset 0 usec, available: no)
properties:
device.icon_name = "audio-input-microphone"
analog-input-rear-mic: Rear Microphone (priority 8200, latency offset 0 usec, available: no)
properties:
device.icon_name = "audio-input-microphone"
analog-input-linein: En línea (priority 8100, latency offset 0 usec, available: no)
properties:
analog-output-lineout: Line Out (priority 9900, latency offset 0 usec, available: yes)
properties:
analog-output-headphones: Auriculares analógicos (priority 9000, latency offset 0 usec, available: no)
properties:
device.icon_name = "audio-headphones"
hdmi-output-0: HDMI / DisplayPort (priority 5900, latency offset 0 usec, available: yes)
properties:
device.icon_name = "video-display"
device.product.name = "ASUS VX239"
hdmi-output-1: HDMI / DisplayPort 2 (priority 5800, latency offset 0 usec, available: no)
properties:
device.icon_name = "video-display"
hdmi-output-2: HDMI / DisplayPort 3 (priority 5700, latency offset 0 usec, available: no)
properties:
device.icon_name = "video-display"
hdmi-output-3: HDMI / DisplayPort 4 (priority 5600, latency offset 0 usec, available: no)
properties:
device.icon_name = "video-display"
hdmi-output-4: HDMI / DisplayPort 5 (priority 5500, latency offset 0 usec, available: no)
properties:
device.icon_name = "video-display"
Offline
And you actually have 2.1 hardware? If this is a laptop, which model exactly? Or why would you want to enable this? FWIW this looks like a newer codec, if you are on LTS try to reproduce on the current linux kernel, sometimes appropriate support has to be switched on in ALSA because the device doesn't automatically advertise for it. What's your output for
amixer -c0
Offline
The speakers are a P3060 Edifier (https://www.edifier.com/my/en/speakers/p3060-2.1-usb) and are connected to the standard audio output of a PC (with the typical audio cable plugged into the green output).
$ amixer -c0
Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback 0 - 87
Mono: Playback 58 [67%] [-21.75dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pswitch
Playback channels: Front Left - Front Right
Mono:
Front Left: Playback [off]
Front Right: Playback [off]
Simple mixer control 'PCM',0
Capabilities: pvolume
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 255 [100%] [0.00dB]
Front Right: Playback 255 [100%] [0.00dB]
Simple mixer control 'Front',0
Capabilities: pvolume pswitch
Playback channels: Front Left - Front Right
Limits: Playback 0 - 87
Mono:
Front Left: Playback 87 [100%] [0.00dB] [on]
Front Right: Playback 87 [100%] [0.00dB] [on]
Simple mixer control 'Front Mic',0
Capabilities: pvolume pswitch
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Front Mic Boost',0
Capabilities: volume
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]
Simple mixer control 'Surround',0
Capabilities: pvolume pswitch
Playback channels: Front Left - Front Right
Limits: Playback 0 - 87
Mono:
Front Left: Playback 87 [100%] [0.00dB] [on]
Front Right: Playback 87 [100%] [0.00dB] [on]
Simple mixer control 'Center',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback 0 - 87
Mono: Playback 87 [100%] [0.00dB] [on]
Simple mixer control 'LFE',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback 0 - 87
Mono: Playback 87 [100%] [0.00dB] [on]
Simple mixer control 'Line',0
Capabilities: pvolume pswitch
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Line Boost',0
Capabilities: volume
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958',1
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958',2
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958',3
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958',4
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch
Capture channels: Front Left - Front Right
Limits: Capture 0 - 63
Front Left: Capture 0 [0%] [-17.25dB] [off]
Front Right: Capture 0 [0%] [-17.25dB] [off]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch
Capture channels: Front Left - Front Right
Limits: Capture 0 - 63
Front Left: Capture 0 [0%] [-17.25dB] [off]
Front Right: Capture 0 [0%] [-17.25dB] [off]
Simple mixer control 'Auto-Mute Mode',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Enabled'
Simple mixer control 'Channel Mode',0
Capabilities: enum
Items: '2ch' '4ch' '6ch'
Item0: '2ch'
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Front Mic' 'Rear Mic' 'Line'
Item0: 'Front Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Front Mic' 'Rear Mic' 'Line'
Item0: 'Front Mic'
Simple mixer control 'Loopback Mixing',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Disabled'
Simple mixer control 'Rear Mic',0
Capabilities: pvolume pswitch
Playback channels: Front Left - Front Right
Limits: Playback 0 - 31
Mono:
Front Left: Playback 0 [0%] [-34.50dB] [off]
Front Right: Playback 0 [0%] [-34.50dB] [off]
Simple mixer control 'Rear Mic Boost',0
Capabilities: volume
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 3
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]
Offline
You might not get that out of the standard jack.
FWIW try switching the channel mode in amixer (or alsamixer for that matter) to 4 Channel mode (you might have to restart pulse after that change with
systemctl --user restart pulseaudio
so that it reparses new config)
Last edited by V1del (2018-11-30 17:20:59)
Offline
Those speakers only have a stereo input. The split from 2 channels to 2.1 channels is just done by a simple low-pass filter in the sub box.
No changes were required to your previous configuration.
Offline
Those speakers only have a stereo input. The split from 2 channels to 2.1 channels is just done by a simple low-pass filter in the sub box.
No changes were required to your previous configuration.
ok, thanks.
Offline