Lagging graphics when watching videos and browsing with Firefox

Sito · 2019-02-05 20:06:37

The general problem here is that whenever I scroll, watch a video, etc. in Firefox some portion of the screen lags behind the rest. I've searched the forums and found this but couldn't really solve the issue with it. I obviously don't know what exactly the issue is, but after some browsing I started to suspect that I didn't have the right drivers (if this isn't the problem any kind of redirection is much appreciated). I used 'lspci -v' to get information about the gpu and drivers, resulting in

$ lspci -v 
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Hawaii PRO [Radeon R9 290/390] (prog-if 00 [VGA controller])
	Subsystem: PC Partner Limited / Sapphire Technology Hawaii PRO [Radeon R9 290/390]
	Flags: bus master, fast devsel, latency 0, IRQ 34
	Memory at e0000000 (64-bit, prefetchable) [size=256M]
	Memory at f0000000 (64-bit, prefetchable) [size=8M]
	I/O ports at e000 [size=256]
	Memory at f7e00000 (32-bit, non-prefetchable) [size=256K]
	Expansion ROM at 000c0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: radeon
	Kernel modules: radeon, amdgpu

According to this Wiki entry my card should be in GCN 2 (this information comes from here and since I don't really know I just trusted post #3), and therefore AMDGPU* / ATI would be the appropriate drivers. I then checked if everything was installed as suggested in this Wiki entry, but wasn't able to install any 'lib32-'packages with the following error:

$ sudo pacman -S lib32-mesa
Fehler: Ziel nicht gefunden: lib32-mesa

which basically translates to "error: entry not found: lib32-mesa". "xf86-video-ati" is installed. As suggested by the wiki I then proceeded to edit "/etc/mkinitcpio.conf" which now looks like this:

MODULES=(amdgpu radeon)
mkinitcpio -p linux

BINARIES=()
FILES=()

HOOKS=(base udev autodetect modconf block filesystems keyboard fsck)

The next instruction "Now, regenerate the initramfs." wasn't really clear to me.. When I try to run

mkinitcpio -c /etc/mkinitcpio.conf -g /boot/linux.img

I get the errors:

==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
  -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
==> ERROR: You appear to be calling a preset from a preset. This is a configuration error.
==> ERROR: Unable to write to /boot/initramfs-linux.img
==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
  -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
==> ERROR: You appear to be calling a preset from a preset. This is a configuration error.
==> ERROR: Unable to write to /boot/initramfs-linux-fallback.img
==> ERROR: Unable to write to /boot/linux.img

So I'm not sure if the issue lies here... The last thing I tried was setting up the "/etc/X11/xorg.conf.d/20-radeon.conf" file with the content

Section "Device"
    Identifier "Radeon"
    Driver "radeon"
EndSection

Nothing of the above really solved my problem and I'm honestly a bit lost at the moment. Any kind of help on how to proceed from here would be appreciated!

agrewal · 2019-02-05 20:40:48

To install lib32-* packages, you have to enable the multilib repositories.

The line

mkinicpio -p linux

should not be inside mkinitcpio.conf. It's a command to run after editing the file.

seth · 2019-02-05 23:38:06

There's also absolutely no point in putting both modules into the initcpio and while early kms might be nice, it won't solve this issue.
You should be using the amdgpu kernel module, but are using the radeon one, so the first step would be to determine what's wrong here.
See whether amdgpu is blacklisted in /etc/modprobe.d/*
Once you can load the amdgpu kernel module you want to get rid of xf86-video-ati, maybe in favor of xf86-video-amdgpu.

I doubt this is a lib32 issue, FF should be 64bit except maybe some proprietary 3rd party plugins.

Sito · 2019-02-06 11:12:46

See whether amdgpu is blacklisted in /etc/modprobe.d/

The directory is empty ('$ ls -a' only shows '. ..'). I tried changing the "/etc/X11/xorg.conf.d/20-radeon.conf" file to "/etc/X11/xorg.conf.d/20-amdgpu.conf" with

Section "Device"
     Identifier "AMD"
     Driver "amdgpu"
 EndSection

which resulted in a crash right after trying to use 'startx'. I changed it back again, but if I'm not mistaken, this should be the log file of the crash:

[     8.937] (WW) Failed to open protocol names file lib/xorg/protocol.txt
[     8.937] 
X.Org X Server 1.20.3
X Protocol Version 11, Revision 0
[     8.937] Build Operating System: Linux Arch Linux
[     8.937] Current Operating System: Linux Tower 4.20.6-arch1-1-ARCH #1 SMP PREEMPT Thu Jan 31 08:22:01 UTC 2019 x86_64
[     8.937] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=4f0920aa-b242-49db-a4b1-300029bb3253 rw quiet
[     8.937] Build Date: 25 October 2018  04:42:32PM
[     8.937]  
[     8.937] Current version of pixman: 0.36.0
[     8.937] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[     8.937] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[     8.937] (==) Log file: "/home/sito/.local/share/xorg/Xorg.0.log", Time: Wed Feb  6 11:18:42 2019
[     8.939] (==) Using config file: "/etc/X11/xorg.conf"
[     8.939] (==) Using config directory: "/etc/X11/xorg.conf.d"
[     8.939] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[     8.940] (==) No Layout section.  Using the first Screen section.
[     8.940] (==) No screen section available. Using defaults.
[     8.940] (**) |-->Screen "Default Screen Section" (0)
[     8.940] (**) |   |-->Monitor "<default monitor>"
[     8.941] (==) No device specified for screen "Default Screen Section".
	Using the first device section listed.
[     8.941] (**) |   |-->Device "AMD"
[     8.941] (==) No monitor specified for screen "Default Screen Section".
	Using a default monitor configuration.
[     8.941] (==) Automatically adding devices
[     8.941] (==) Automatically enabling devices
[     8.941] (==) Automatically adding GPU devices
[     8.941] (==) Automatically binding GPU devices
[     8.941] (==) Max clients allowed: 256, resource mask: 0x1fffff
[     8.942] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[     8.942] 	Entry deleted from font path.
[     8.942] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi".
[     8.942] 	Entry deleted from font path.
[     8.942] 	(Run 'mkfontdir' on "/usr/share/fonts/100dpi").
[     8.942] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi".
[     8.942] 	Entry deleted from font path.
[     8.942] 	(Run 'mkfontdir' on "/usr/share/fonts/75dpi").
[     8.942] (==) FontPath set to:
	/usr/share/fonts/misc,
	/usr/share/fonts/TTF,
	/usr/share/fonts/OTF
[     8.942] (==) ModulePath set to "/usr/lib/xorg/modules"
[     8.942] (WW) Ignoring unrecognized extension "Composite"
[     8.942] (II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
[     8.942] (II) Module ABI versions:
[     8.942] 	X.Org ANSI C Emulation: 0.4
[     8.942] 	X.Org Video Driver: 24.0
[     8.942] 	X.Org XInput driver : 24.1
[     8.942] 	X.Org Server Extension : 10.0
[     8.943] (++) using VT number 1

[     8.944] (II) systemd-logind: took control of session /org/freedesktop/login1/session/_31
[     8.945] (II) xfree86: Adding drm device (/dev/dri/card0)
[     8.946] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 10 paused 0
[     8.948] (--) PCI:*(1@0:0:0) 1002:67b1:174b:e283 rev 0, Mem @ 0xe0000000/268435456, 0xf0000000/8388608, 0xf7e00000/262144, I/O @ 0x0000e000/256, BIOS @ 0x????????/131072
[     8.948] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[     8.948] (II) LoadModule: "glx"
[     8.950] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[     8.957] (II) Module glx: vendor="X.Org Foundation"
[     8.957] 	compiled for 1.20.3, module version = 1.0.0
[     8.957] 	ABI class: X.Org Server Extension, version 10.0
[     8.957] (II) LoadModule: "amdgpu"
[     8.957] (II) Loading /usr/lib/xorg/modules/drivers/amdgpu_drv.so
[     8.960] (II) Module amdgpu: vendor="X.Org Foundation"
[     8.960] 	compiled for 1.20.1, module version = 18.1.0
[     8.960] 	Module class: X.Org Video Driver
[     8.960] 	ABI class: X.Org Video Driver, version 24.0
[     8.960] (II) AMDGPU: Driver for AMD Radeon:
	All GPUs supported by the amdgpu kernel driver
[     8.960] (EE) AMDGPU(0): amdgpu_device_initialize failed
[     8.960] (II) AMDGPU(1): [KMS] Kernel modesetting enabled.
[     8.960] (EE) AMDGPU(1): [drm] failed to set drm interface version.
[     8.960] (EE) AMDGPU(G0): amdgpu_device_initialize failed
[     8.960] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[     8.960] (EE) Screen 0 deleted because of no matching config section.
[     8.960] (II) UnloadModule: "amdgpu"
[     8.960] (EE) Screen 0 deleted because of no matching config section.
[     8.960] (II) UnloadModule: "amdgpu"
[     8.960] (EE) Device(s) detected, but none match those in the config file.
[     8.960] (EE) 
Fatal server error:
[     8.960] (EE) no screens found(EE) 
[     8.960] (EE) 
Please consult the The X.Org Foundation support 
	 at http://wiki.x.org
 for help. 
[     8.960] (EE) Please also check the log file at "/home/sito/.local/share/xorg/Xorg.0.log" for additional information.
[     8.960] (EE) 
[     8.964] (EE) Server terminated with error (1). Closing log file.

V1del · 2019-02-06 11:34:07

Check your dmesg, however it's very likely that you have to do this to enable the usage of AMDGPU

seth · 2019-02-06 12:52:14

What would be rather odd, since this should™ be a volcanic island GPU.

Sito · 2019-02-06 13:51:26

Check your dmesg, however it's very likely that you have to do this to enable the usage of AMDGPU

I'm not really sure for what I should be looking, so I'll just post the output...

$ dmesg
[    0.000000] Linux version 4.20.6-arch1-1-ARCH (builduser@heftig-32156) (gcc version 8.2.1 20181127 (GCC)) #1 SMP PREEMPT Thu Jan 31 08:22:01 UTC 2019
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=4f0920aa-b242-49db-a4b1-300029bb3253 rw quiet
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Hygon HygonGenuine
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000c9e3afff] usable
[    0.000000] BIOS-e820: [mem 0x00000000c9e3b000-0x00000000c9e41fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000c9e42000-0x00000000ca7bcfff] usable
[    0.000000] BIOS-e820: [mem 0x00000000ca7bd000-0x00000000caa77fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000caa78000-0x00000000dd39afff] usable
[    0.000000] BIOS-e820: [mem 0x00000000dd39b000-0x00000000dd42bfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000dd42c000-0x00000000dd490fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000dd491000-0x00000000dd5d3fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000dd5d4000-0x00000000deffefff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000defff000-0x00000000deffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041dffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: Gigabyte Technology Co., Ltd. H97-D3H/H97-D3H-CF, BIOS F5 06/26/2014
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 3400.112 MHz processor
[    0.001327] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.001328] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.001333] last_pfn = 0x41e000 max_arch_pfn = 0x400000000
[    0.001335] MTRR default type: uncachable
[    0.001336] MTRR fixed ranges enabled:
[    0.001336]   00000-9FFFF write-back
[    0.001337]   A0000-BFFFF uncachable
[    0.001337]   C0000-CFFFF write-protect
[    0.001338]   D0000-E7FFF uncachable
[    0.001338]   E8000-FFFFF write-protect
[    0.001339] MTRR variable ranges enabled:
[    0.001340]   0 base 0000000000 mask 7C00000000 write-back
[    0.001340]   1 base 0400000000 mask 7FF0000000 write-back
[    0.001341]   2 base 0410000000 mask 7FF8000000 write-back
[    0.001341]   3 base 0418000000 mask 7FFC000000 write-back
[    0.001342]   4 base 041C000000 mask 7FFE000000 write-back
[    0.001342]   5 base 00E0000000 mask 7FE0000000 uncachable
[    0.001343]   6 disabled
[    0.001343]   7 disabled
[    0.001343]   8 disabled
[    0.001344]   9 disabled
[    0.002572] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.002758] total RAM covered: 16352M
[    0.003008] Found optimal setting for mtrr clean up
[    0.003009]  gran_size: 64K 	chunk_size: 64M 	num_reg: 7  	lose cover RAM: 0G
[    0.003775] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[    0.003778] last_pfn = 0xdf000 max_arch_pfn = 0x400000000
[    0.008963] found SMP MP-table at [mem 0x000fd710-0x000fd71f] mapped at [(____ptrval____)]
[    0.015350] check: Scanning 1 areas for low memory corruption
[    0.015352] Base memory trampoline at [(____ptrval____)] 97000 size 24576
[    0.015354] Using GB pages for direct mapping
[    0.015356] BRK [0x3df001000, 0x3df001fff] PGTABLE
[    0.015357] BRK [0x3df002000, 0x3df002fff] PGTABLE
[    0.015357] BRK [0x3df003000, 0x3df003fff] PGTABLE
[    0.015368] BRK [0x3df004000, 0x3df004fff] PGTABLE
[    0.015369] BRK [0x3df005000, 0x3df005fff] PGTABLE
[    0.015370] BRK [0x3df006000, 0x3df006fff] PGTABLE
[    0.015474] BRK [0x3df007000, 0x3df007fff] PGTABLE
[    0.015490] BRK [0x3df008000, 0x3df008fff] PGTABLE
[    0.015540] BRK [0x3df009000, 0x3df009fff] PGTABLE
[    0.015559] BRK [0x3df00a000, 0x3df00afff] PGTABLE
[    0.015589] BRK [0x3df00b000, 0x3df00bfff] PGTABLE
[    0.015607] BRK [0x3df00c000, 0x3df00cfff] PGTABLE
[    0.015670] RAMDISK: [mem 0x37133000-0x37890fff]
[    0.015674] ACPI: Early table checksum verification disabled
[    0.017348] ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
[    0.017349] ACPI: XSDT 0x00000000DD599080 00007C (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.017353] ACPI: FACP 0x00000000DD5A9CA8 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
[    0.017356] ACPI: DSDT 0x00000000DD599190 010B13 (v02 ALASKA A M I    00000088 INTL 20120711)
[    0.017358] ACPI: FACS 0x00000000DD5D2080 000040
[    0.017360] ACPI: APIC 0x00000000DD5A9DB8 000092 (v03 ALASKA A M I    01072009 AMI  00010013)
[    0.017361] ACPI: FPDT 0x00000000DD5A9E50 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.017363] ACPI: SSDT 0x00000000DD5A9E98 000BEE (v01 Ther_R Ther_Rvp 00001000 INTL 20120711)
[    0.017365] ACPI: SSDT 0x00000000DD5AAA88 000539 (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
[    0.017367] ACPI: SSDT 0x00000000DD5AAFC8 000B74 (v01 CpuRef CpuSsdt  00003000 INTL 20051117)
[    0.017368] ACPI: MCFG 0x00000000DD5ABB40 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
[    0.017370] ACPI: HPET 0x00000000DD5ABB80 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
[    0.017371] ACPI: SSDT 0x00000000DD5ABBB8 00036D (v01 SataRe SataTabl 00001000 INTL 20120711)
[    0.017373] ACPI: SSDT 0x00000000DD5ABF28 005B5E (v01 SaSsdt SaSsdt   00003000 INTL 20120711)
[    0.017375] ACPI: DMAR 0x00000000DD5B1A88 000080 (v01 INTEL  BDW      00000001 INTL 00000001)
[    0.017380] ACPI: Local APIC address 0xfee00000
[    0.017435] No NUMA configuration found
[    0.017435] Faking a node at [mem 0x0000000000000000-0x000000041dffffff]
[    0.017438] NODE_DATA(0) allocated [mem 0x41dffb000-0x41dffefff]
[    0.017454] Zone ranges:
[    0.017455]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.017456]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.017456]   Normal   [mem 0x0000000100000000-0x000000041dffffff]
[    0.017457]   Device   empty
[    0.017457] Movable zone start for each node
[    0.017458] Early memory node ranges
[    0.017458]   node   0: [mem 0x0000000000001000-0x000000000009cfff]
[    0.017459]   node   0: [mem 0x0000000000100000-0x00000000c9e3afff]
[    0.017459]   node   0: [mem 0x00000000c9e42000-0x00000000ca7bcfff]
[    0.017459]   node   0: [mem 0x00000000caa78000-0x00000000dd39afff]
[    0.017460]   node   0: [mem 0x00000000dd42c000-0x00000000dd490fff]
[    0.017460]   node   0: [mem 0x00000000defff000-0x00000000deffffff]
[    0.017461]   node   0: [mem 0x0000000100000000-0x000000041dffffff]
[    0.017567] Zeroed struct page in unavailable ranges: 12069 pages
[    0.017568] Initmem setup node 0 [mem 0x0000000000001000-0x000000041dffffff]
[    0.017569] On node 0 totalpages: 4174043
[    0.017569]   DMA zone: 64 pages used for memmap
[    0.017570]   DMA zone: 21 pages reserved
[    0.017570]   DMA zone: 3996 pages, LIFO batch:0
[    0.017628]   DMA32 zone: 14085 pages used for memmap
[    0.017629]   DMA32 zone: 901439 pages, LIFO batch:63
[    0.030298]   Normal zone: 51072 pages used for memmap
[    0.030299]   Normal zone: 3268608 pages, LIFO batch:63
[    0.074703] ACPI: PM-Timer IO Port: 0x1808
[    0.074705] ACPI: Local APIC address 0xfee00000
[    0.074710] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.074719] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.074720] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.074721] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.074722] ACPI: IRQ0 used by override.
[    0.074723] ACPI: IRQ9 used by override.
[    0.074724] Using ACPI (MADT) for SMP configuration information
[    0.074725] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.074728] [Firmware Bug]: TSC_DEADLINE disabled due to Errata; please update microcode to version: 0x22 (or later)
[    0.074729] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[    0.074740] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.074741] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[    0.074742] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[    0.074742] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.074742] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.074743] PM: Registered nosave memory: [mem 0xc9e3b000-0xc9e41fff]
[    0.074744] PM: Registered nosave memory: [mem 0xca7bd000-0xcaa77fff]
[    0.074745] PM: Registered nosave memory: [mem 0xdd39b000-0xdd42bfff]
[    0.074746] PM: Registered nosave memory: [mem 0xdd491000-0xdd5d3fff]
[    0.074747] PM: Registered nosave memory: [mem 0xdd5d4000-0xdeffefff]
[    0.074747] PM: Registered nosave memory: [mem 0xdf000000-0xf7ffffff]
[    0.074748] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[    0.074748] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[    0.074749] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.074749] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[    0.074749] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[    0.074750] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[    0.074750] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[    0.074750] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[    0.074751] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.074751] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[    0.074752] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.074753] [mem 0xdf000000-0xf7ffffff] available for PCI devices
[    0.074754] Booting paravirtualized kernel on bare hardware
[    0.074756] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[    0.150612] random: get_random_bytes called from start_kernel+0x95/0x548 with crng_init=0
[    0.150616] setup_percpu: NR_CPUS:320 nr_cpumask_bits:320 nr_cpu_ids:8 nr_node_ids:1
[    0.150765] percpu: Embedded 45 pages/cpu @(____ptrval____) s147456 r8192 d28672 u262144
[    0.150769] pcpu-alloc: s147456 r8192 d28672 u262144 alloc=1*2097152
[    0.150770] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.150781] Built 1 zonelists, mobility grouping on.  Total pages: 4108801
[    0.150782] Policy zone: Normal
[    0.150783] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=4f0920aa-b242-49db-a4b1-300029bb3253 rw quiet
[    0.153806] Calgary: detecting Calgary via BIOS EBDA area
[    0.153807] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.189261] Memory: 16330196K/16696172K available (12293K kernel code, 1268K rwdata, 3688K rodata, 1536K init, 3936K bss, 365976K reserved, 0K cma-reserved)
[    0.189367] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.189371] Kernel/User page tables isolation: enabled
[    0.189381] ftrace: allocating 35810 entries in 140 pages
[    0.198697] rcu: Preemptible hierarchical RCU implementation.
[    0.198698] rcu: 	CONFIG_RCU_FANOUT set to non-default value of 32.
[    0.198698] rcu: 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.198698] rcu: 	RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=8.
[    0.198699] rcu: 	RCU priority boosting: priority 1 delay 500 ms.
[    0.198699] 	Tasks RCU enabled.
[    0.198700] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.198700] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.199651] NR_IRQS: 20736, nr_irqs: 488, preallocated irqs: 16
[    0.199806] rcu: 	Offload RCU callbacks from CPUs: (none).
[    0.199841] spurious 8259A interrupt: IRQ7.
[    0.199851] Console: colour dummy device 80x25
[    0.199854] printk: console [tty0] enabled
[    0.199866] ACPI: Core revision 20181003
[    0.200012] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.200018] hpet clockevent registered
[    0.200021] APIC: Switch to symmetric I/O mode setup
[    0.200022] DMAR: Host address width 39
[    0.200023] DMAR: DRHD base: 0x000000fed90000 flags: 0x1
[    0.200025] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap d2008c20660462 ecap f010da
[    0.200026] DMAR: RMRR base: 0x000000deecf000 end: 0x000000deeddfff
[    0.200027] DMAR-IR: IOAPIC id 8 under DRHD base  0xfed90000 IOMMU 0
[    0.200028] DMAR-IR: HPET id 0 under DRHD base 0xfed90000
[    0.200028] DMAR-IR: x2apic is disabled because BIOS sets x2apic opt out bit.
[    0.200028] DMAR-IR: Use 'intremap=no_x2apic_optout' to override the BIOS setting.
[    0.200237] DMAR-IR: Enabled IRQ remapping in xapic mode
[    0.200237] x2apic: IRQ remapping doesn't support X2APIC mode
[    0.200599] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.216688] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x3102b84eb4a, max_idle_ns: 440795279893 ns
[    0.216696] Calibrating delay loop (skipped), value calculated using timer frequency.. 6802.56 BogoMIPS (lpj=11333706)
[    0.216697] pid_max: default: 32768 minimum: 301
[    0.216719] LSM: Security Framework initializing
[    0.216720] Yama: becoming mindful.
[    0.216723] AppArmor: AppArmor disabled by boot time parameter
[    0.218557] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.219482] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.219521] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.219550] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.219704] mce: CPU supports 9 MCE banks
[    0.219710] CPU0: Thermal monitoring enabled (TM1)
[    0.219719] process: using mwait in idle threads
[    0.219721] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
[    0.219721] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[    0.219722] Spectre V2 : Mitigation: Full generic retpoline
[    0.219723] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.219723] Speculative Store Bypass: Vulnerable
[    0.219832] Freeing SMP alternatives memory: 28K
[    0.223356] smpboot: CPU0: Intel(R) Xeon(R) CPU E3-1231 v3 @ 3.40GHz (family: 0x6, model: 0x3c, stepping: 0x3)
[    0.240027] Performance Events: PEBS fmt2+, Haswell events, 16-deep LBR, full-width counters, Intel PMU driver.
[    0.240040] ... version:                3
[    0.240040] ... bit width:              48
[    0.240041] ... generic registers:      4
[    0.240041] ... value mask:             0000ffffffffffff
[    0.240042] ... max period:             00007fffffffffff
[    0.240042] ... fixed-purpose events:   3
[    0.240043] ... event mask:             000000070000000f
[    0.246691] rcu: Hierarchical SRCU implementation.
[    0.270139] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.276694] smp: Bringing up secondary CPUs ...
[    0.316698] x86: Booting SMP configuration:
[    0.316699] .... node  #0, CPUs:      #1 #2 #3 #4 #5 #6 #7
[    0.557010] smp: Brought up 1 node, 8 CPUs
[    0.557010] smpboot: Max logical packages: 1
[    0.557010] smpboot: Total of 8 processors activated (54423.53 BogoMIPS)
[    0.563635] devtmpfs: initialized
[    0.563635] x86/mm: Memory block size: 128MB
[    0.564149] PM: Registering ACPI NVS region [mem 0xc9e3b000-0xc9e41fff] (28672 bytes)
[    0.564149] PM: Registering ACPI NVS region [mem 0xdd491000-0xdd5d3fff] (1323008 bytes)
[    0.564149] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.564149] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.564149] pinctrl core: initialized pinctrl subsystem
[    0.564149] RTC time: 11:30:36, date: 02/06/19
[    0.564149] NET: Registered protocol family 16
[    0.564149] audit: initializing netlink subsys (disabled)
[    0.564149] audit: type=2000 audit(1549452636.363:1): state=initialized audit_enabled=0 res=1
[    0.564149] cpuidle: using governor ladder
[    0.566693] cpuidle: using governor menu
[    0.566712] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.566713] ACPI: bus type PCI registered
[    0.566714] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.566755] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.566757] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.566763] PCI: Using configuration type 1 for base access
[    0.566775] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[    0.567544] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.567544] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.567544] ACPI: Added _OSI(Module Device)
[    0.567544] ACPI: Added _OSI(Processor Device)
[    0.567544] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.567544] ACPI: Added _OSI(Processor Aggregator Device)
[    0.567544] ACPI: Added _OSI(Linux-Dell-Video)
[    0.567544] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.580460] ACPI: 6 ACPI AML tables successfully acquired and loaded
[    0.583509] ACPI: Dynamic OEM Table Load:
[    0.583509] ACPI: SSDT 0xFFFF95818B2E5400 0003D3 (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
[    0.583631] ACPI: Dynamic OEM Table Load:
[    0.583634] ACPI: SSDT 0xFFFF95818B737800 0005AA (v01 PmRef  ApIst    00003000 INTL 20051117)
[    0.584018] ACPI: Dynamic OEM Table Load:
[    0.584018] ACPI: SSDT 0xFFFF95818B2BC400 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
[    0.586929] ACPI: Interpreter enabled
[    0.586954] ACPI: (supports S0 S3 S4 S5)
[    0.586955] ACPI: Using IOAPIC for interrupt routing
[    0.586979] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.587648] ACPI: Enabled 9 GPEs in block 00 to 3F
[    0.588333] ACPI: Power Resource [PG00] (on)
[    0.588453] ACPI: Power Resource [PG01] (on)
[    0.588453] ACPI: Power Resource [PG02] (on)
[    0.599767] ACPI: Power Resource [FN00] (off)
[    0.599826] ACPI: Power Resource [FN01] (off)
[    0.599884] ACPI: Power Resource [FN02] (off)
[    0.599940] ACPI: Power Resource [FN03] (off)
[    0.599999] ACPI: Power Resource [FN04] (off)
[    0.600804] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.600808] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.601329] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR]
[    0.601330] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
[    0.601822] PCI host bridge to bus 0000:00
[    0.601823] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.601824] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.601825] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.601826] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[    0.601827] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[    0.601828] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[    0.601829] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[    0.601830] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[    0.601830] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[    0.601831] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfeafffff window]
[    0.601832] pci_bus 0000:00: root bus resource [bus 00-3e]
[    0.601838] pci 0000:00:00.0: [8086:0c08] type 00 class 0x060000
[    0.601917] pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
[    0.601946] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.602069] pci 0000:00:14.0: [8086:8cb1] type 00 class 0x0c0330
[    0.602086] pci 0000:00:14.0: reg 0x10: [mem 0xf7f20000-0xf7f2ffff 64bit]
[    0.602137] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.602205] pci 0000:00:16.0: [8086:8cba] type 00 class 0x078000
[    0.602222] pci 0000:00:16.0: reg 0x10: [mem 0xf7f39000-0xf7f3900f 64bit]
[    0.602275] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.602362] pci 0000:00:19.0: [8086:153b] type 00 class 0x020000
[    0.602377] pci 0000:00:19.0: reg 0x10: [mem 0xf7f00000-0xf7f1ffff]
[    0.602383] pci 0000:00:19.0: reg 0x14: [mem 0xf7f38000-0xf7f38fff]
[    0.602389] pci 0000:00:19.0: reg 0x18: [io  0xf040-0xf05f]
[    0.602438] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[    0.602507] pci 0000:00:1a.0: [8086:8cad] type 00 class 0x0c0320
[    0.602525] pci 0000:00:1a.0: reg 0x10: [mem 0xf7f37000-0xf7f373ff]
[    0.602595] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.602666] pci 0000:00:1b.0: [8086:8ca0] type 00 class 0x040300
[    0.602682] pci 0000:00:1b.0: reg 0x10: [mem 0xf7f30000-0xf7f33fff 64bit]
[    0.602740] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.602807] pci 0000:00:1c.0: [8086:8c90] type 01 class 0x060400
[    0.602867] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.602978] pci 0000:00:1c.3: [8086:8c96] type 01 class 0x060400
[    0.603040] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.603150] pci 0000:00:1d.0: [8086:8ca6] type 00 class 0x0c0320
[    0.603168] pci 0000:00:1d.0: reg 0x10: [mem 0xf7f36000-0xf7f363ff]
[    0.603239] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.603312] pci 0000:00:1f.0: [8086:8cc6] type 00 class 0x060100
[    0.603470] pci 0000:00:1f.2: [8086:8c82] type 00 class 0x010601
[    0.603483] pci 0000:00:1f.2: reg 0x10: [io  0xf090-0xf097]
[    0.603489] pci 0000:00:1f.2: reg 0x14: [io  0xf080-0xf083]
[    0.603494] pci 0000:00:1f.2: reg 0x18: [io  0xf070-0xf077]
[    0.603499] pci 0000:00:1f.2: reg 0x1c: [io  0xf060-0xf063]
[    0.603505] pci 0000:00:1f.2: reg 0x20: [io  0xf020-0xf03f]
[    0.603510] pci 0000:00:1f.2: reg 0x24: [mem 0xf7f35000-0xf7f357ff]
[    0.603539] pci 0000:00:1f.2: PME# supported from D3hot
[    0.603602] pci 0000:00:1f.3: [8086:8ca2] type 00 class 0x0c0500
[    0.603616] pci 0000:00:1f.3: reg 0x10: [mem 0xf7f34000-0xf7f340ff 64bit]
[    0.603632] pci 0000:00:1f.3: reg 0x20: [io  0xf000-0xf01f]
[    0.603731] pci 0000:01:00.0: [1002:67b1] type 00 class 0x030000
[    0.603746] pci 0000:01:00.0: reg 0x10: [mem 0xe0000000-0xefffffff 64bit pref]
[    0.603752] pci 0000:01:00.0: reg 0x18: [mem 0xf0000000-0xf07fffff 64bit pref]
[    0.603757] pci 0000:01:00.0: reg 0x20: [io  0xe000-0xe0ff]
[    0.603761] pci 0000:01:00.0: reg 0x24: [mem 0xf7e00000-0xf7e3ffff]
[    0.603766] pci 0000:01:00.0: reg 0x30: [mem 0xf7e40000-0xf7e5ffff pref]
[    0.603800] pci 0000:01:00.0: supports D1 D2
[    0.603801] pci 0000:01:00.0: PME# supported from D1 D2 D3hot
[    0.603847] pci 0000:01:00.1: [1002:aac8] type 00 class 0x040300
[    0.603860] pci 0000:01:00.1: reg 0x10: [mem 0xf7e60000-0xf7e63fff 64bit]
[    0.603906] pci 0000:01:00.1: supports D1 D2
[    0.603951] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.603952] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.603954] pci 0000:00:01.0:   bridge window [mem 0xf7e00000-0xf7efffff]
[    0.603956] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xf07fffff 64bit pref]
[    0.604001] acpiphp: Slot [1] registered
[    0.604004] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.604063] pci 0000:03:00.0: [8086:244e] type 01 class 0x060401
[    0.604185] pci 0000:03:00.0: supports D1 D2
[    0.604186] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.604251] pci 0000:00:1c.3: PCI bridge to [bus 03-04]
[    0.604294] pci_bus 0000:04: extended config space not accessible
[    0.604368] pci 0000:03:00.0: PCI bridge to [bus 04] (subtractive decode)
[    0.605148] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 6 10 *11 12 14 15)
[    0.605196] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 6 *10 11 12 14 15)
[    0.605242] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 6 10 *11 12 14 15)
[    0.605288] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 6 10 *11 12 14 15)
[    0.605334] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 6 10 *11 12 14 15)
[    0.605381] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 6 10 11 12 14 15) *0, disabled.
[    0.605426] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 6 *10 11 12 14 15)
[    0.605472] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 6 *10 11 12 14 15)
[    0.605781] pci 0000:01:00.0: vgaarb: setting as boot VGA device
[    0.605781] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.605781] pci 0000:01:00.0: vgaarb: bridge control possible
[    0.605781] vgaarb: loaded
[    0.605781] ACPI: bus type USB registered
[    0.605781] usbcore: registered new interface driver usbfs
[    0.605781] usbcore: registered new interface driver hub
[    0.605781] usbcore: registered new device driver usb
[    0.605781] pps_core: LinuxPPS API ver. 1 registered
[    0.605781] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.605781] PTP clock support registered
[    0.605781] EDAC MC: Ver: 3.0.0
[    0.605781] PCI: Using ACPI for IRQ routing
[    0.607188] PCI: pci_cache_line_size set to 64 bytes
[    0.607225] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[    0.607225] e820: reserve RAM buffer [mem 0xc9e3b000-0xcbffffff]
[    0.607226] e820: reserve RAM buffer [mem 0xca7bd000-0xcbffffff]
[    0.607227] e820: reserve RAM buffer [mem 0xdd39b000-0xdfffffff]
[    0.607228] e820: reserve RAM buffer [mem 0xdd491000-0xdfffffff]
[    0.607228] e820: reserve RAM buffer [mem 0xdf000000-0xdfffffff]
[    0.607229] e820: reserve RAM buffer [mem 0x41e000000-0x41fffffff]
[    0.607289] NetLabel: Initializing
[    0.607290] NetLabel:  domain hash size = 128
[    0.607290] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.607299] NetLabel:  unlabeled traffic allowed by default
[    0.607301] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.607301] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.608730] clocksource: Switched to clocksource tsc-early
[    0.613838] VFS: Disk quotas dquot_6.6.0
[    0.613848] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.613889] pnp: PnP ACPI init
[    0.613974] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.613978] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.614053] system 00:01: [io  0x0800-0x087f] has been reserved
[    0.614056] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.614071] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.614100] system 00:03: [io  0x1854-0x1857] has been reserved
[    0.614103] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.614233] system 00:04: [io  0x0a00-0x0a0f] has been reserved
[    0.614235] system 00:04: [io  0x0a30-0x0a3f] has been reserved
[    0.614236] system 00:04: [io  0x0a20-0x0a2f] has been reserved
[    0.614238] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.614443] pnp 00:05: [dma 0 disabled]
[    0.614475] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.614512] system 00:06: [io  0x04d0-0x04d1] has been reserved
[    0.614515] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.614921] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.614923] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.614924] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.614925] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.614926] system 00:07: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.614927] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.614928] system 00:07: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.614929] system 00:07: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.614930] system 00:07: [mem 0xff000000-0xffffffff] has been reserved
[    0.614931] system 00:07: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.614932] system 00:07: [mem 0xf7fe0000-0xf7feffff] has been reserved
[    0.614935] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.615097] pnp: PnP ACPI: found 8 devices
[    0.620401] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.620430] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.620431] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.620433] pci 0000:00:01.0:   bridge window [mem 0xf7e00000-0xf7efffff]
[    0.620435] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xf07fffff 64bit pref]
[    0.620437] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.620445] pci 0000:03:00.0: PCI bridge to [bus 04]
[    0.620463] pci 0000:00:1c.3: PCI bridge to [bus 03-04]
[    0.620471] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.620472] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.620473] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.620474] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
[    0.620475] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
[    0.620476] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
[    0.620477] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
[    0.620478] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff window]
[    0.620479] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff window]
[    0.620480] pci_bus 0000:00: resource 13 [mem 0xe0000000-0xfeafffff window]
[    0.620481] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.620481] pci_bus 0000:01: resource 1 [mem 0xf7e00000-0xf7efffff]
[    0.620482] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xf07fffff 64bit pref]
[    0.620592] NET: Registered protocol family 2
[    0.620686] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes)
[    0.620730] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.620855] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.620955] TCP: Hash tables configured (established 131072 bind 65536)
[    0.620980] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.621013] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.621066] NET: Registered protocol family 1
[    0.621069] NET: Registered protocol family 44
[    0.640769] pci 0000:00:1a.0: quirk_usb_early_handoff+0x0/0x6ad took 19082 usecs
[    0.660688] pci 0000:00:1d.0: quirk_usb_early_handoff+0x0/0x6ad took 19442 usecs
[    0.660702] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.660706] pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
[    0.660731] PCI: CLS 64 bytes, default 64
[    0.660756] Unpacking initramfs...
[    0.734517] Freeing initrd memory: 7544K
[    0.760702] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.760704] software IO TLB: mapped [mem 0xd939b000-0xdd39b000] (64MB)
[    0.760810] check: Scanning for low memory corruption every 60 seconds
[    0.761181] Initialise system trusted keyrings
[    0.761188] Key type blacklist registered
[    0.761217] workingset: timestamp_bits=41 max_order=22 bucket_order=0
[    0.762028] zbud: loaded
[    0.779860] Key type asymmetric registered
[    0.779861] Asymmetric key parser 'x509' registered
[    0.779867] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.779892] io scheduler noop registered
[    0.779893] io scheduler deadline registered
[    0.779911] io scheduler cfq registered (default)
[    0.779912] io scheduler mq-deadline registered
[    0.779912] io scheduler kyber registered
[    0.779935] io scheduler bfq registered
[    0.780199] pcieport 0000:00:01.0: Signaling PME with IRQ 25
[    0.780317] pcieport 0000:00:1c.0: Signaling PME with IRQ 26
[    0.780435] pcieport 0000:00:1c.3: Signaling PME with IRQ 27
[    0.780475] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.780520] vesafb: mode is 1920x1080x32, linelength=7680, pages=0
[    0.780520] vesafb: scrolling: redraw
[    0.780521] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[    0.780531] vesafb: framebuffer at 0xe0000000, mapped to 0x0000000061676550, using 8128k, total 8128k
[    0.780556] fbcon: Deferring console take-over
[    0.780557] fb0: VESA VGA frame buffer device
[    0.780566] intel_idle: MWAIT substates: 0x42120
[    0.780566] intel_idle: v0.4.1 model 0x3C
[    0.780823] intel_idle: lapic_timer_reliable_states 0xffffffff
[    0.780889] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.780899] ACPI: Power Button [PWRB]
[    0.780924] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[    0.780929] ACPI: Sleep Button [SLPB]
[    0.780950] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.780954] ACPI: Power Button [PWRF]
[    0.781847] thermal LNXTHERM:00: registered as thermal_zone0
[    0.781848] ACPI: Thermal Zone [TZ00] (28 C)
[    0.782043] thermal LNXTHERM:01: registered as thermal_zone1
[    0.782043] ACPI: Thermal Zone [TZ01] (30 C)
[    0.782238] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.802796] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.803973] usbcore: registered new interface driver usbserial_generic
[    0.803985] usbserial: USB Serial support registered for generic
[    0.803998] rtc_cmos 00:02: RTC can wake from S4
[    0.804119] rtc_cmos 00:02: registered as rtc0
[    0.804128] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    0.804158] intel_pstate: Intel P-state driver initializing
[    0.804674] ledtrig-cpu: registered to indicate activity on CPUs
[    0.805252] NET: Registered protocol family 10
[    0.818785] Segment Routing with IPv6
[    0.818839] NET: Registered protocol family 17
[    0.819641] RAS: Correctable Errors collector initialized.
[    0.819673] microcode: sig=0x306c3, pf=0x2, revision=0x19
[    0.819817] microcode: Microcode Update Driver: v2.2.
[    0.819825] sched_clock: Marking stable (819617108, 196373)->(929628379, -109814898)
[    0.820047] registered taskstats version 1
[    0.820056] Loading compiled-in X.509 certificates
[    0.822491] Loaded X.509 cert 'Build time autogenerated kernel key: 74a5a057e5fda6fa409239220c77773d3f1f6cba'
[    0.822512] zswap: loaded using pool lzo/zbud
[    0.826534] Key type big_key registered
[    0.827060]   Magic number: 7:69:529
[    0.827175] rtc_cmos 00:02: setting system clock to 2019-02-06 11:30:36 UTC (1549452636)
[    0.828150] Freeing unused decrypted memory: 2040K
[    0.828407] Freeing unused kernel image memory: 1536K
[    0.847407] Write protecting the kernel read-only data: 18432k
[    0.848206] Freeing unused kernel image memory: 2016K
[    0.848401] Freeing unused kernel image memory: 408K
[    0.861108] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.861109] x86/mm: Checking user space page tables
[    0.869781] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.869782] Run /init as init process
[    0.878316] fbcon: Taking over console
[    0.878363] Console: switching to colour frame buffer device 240x67
[    1.021128] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.022063] ehci-pci: EHCI PCI platform driver
[    1.022240] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    1.022244] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    1.022254] ehci-pci 0000:00:1a.0: debug port 2
[    1.026155] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    1.026168] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7f37000
[    1.026790] SCSI subsystem initialized
[    1.032284] libata version 3.00 loaded.
[    1.034525] ahci 0000:00:1f.2: version 3.0
[    1.034659] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0xe impl SATA mode
[    1.034661] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part ems apst 
[    1.037358] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    1.037386] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
[    1.037388] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.037389] usb usb1: Product: EHCI Host Controller
[    1.037389] usb usb1: Manufacturer: Linux 4.20.6-arch1-1-ARCH ehci_hcd
[    1.037390] usb usb1: SerialNumber: 0000:00:1a.0
[    1.037468] hub 1-0:1.0: USB hub found
[    1.037471] hub 1-0:1.0: 2 ports detected
[    1.037569] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.037572] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    1.038623] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810
[    1.038626] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    1.038729] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
[    1.038730] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.038730] usb usb2: Product: xHCI Host Controller
[    1.038731] usb usb2: Manufacturer: Linux 4.20.6-arch1-1-ARCH xhci-hcd
[    1.038732] usb usb2: SerialNumber: 0000:00:14.0
[    1.038793] hub 2-0:1.0: USB hub found
[    1.038807] hub 2-0:1.0: 14 ports detected
[    1.041338] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    1.041342] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 3
[    1.041352] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.041353] ehci-pci 0000:00:1d.0: debug port 2
[    1.041355] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[    1.041357] xhci_hcd 0000:00:14.0: Host supports USB 3.0  SuperSpeed
[    1.041383] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.20
[    1.041384] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.041385] usb usb4: Product: xHCI Host Controller
[    1.041386] usb usb4: Manufacturer: Linux 4.20.6-arch1-1-ARCH xhci-hcd
[    1.041387] usb usb4: SerialNumber: 0000:00:14.0
[    1.041483] hub 4-0:1.0: USB hub found
[    1.041495] hub 4-0:1.0: 6 ports detected
[    1.045259] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    1.045270] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7f36000
[    1.054579] scsi host0: ahci
[    1.054798] scsi host1: ahci
[    1.054994] scsi host2: ahci
[    1.055129] scsi host3: ahci
[    1.055253] scsi host4: ahci
[    1.055359] scsi host5: ahci
[    1.055408] ata1: DUMMY
[    1.055411] ata2: SATA max UDMA/133 abar m2048@0xf7f35000 port 0xf7f35180 irq 28
[    1.055413] ata3: SATA max UDMA/133 abar m2048@0xf7f35000 port 0xf7f35200 irq 28
[    1.055414] ata4: SATA max UDMA/133 abar m2048@0xf7f35000 port 0xf7f35280 irq 28
[    1.055415] ata5: DUMMY
[    1.055416] ata6: DUMMY
[    1.057371] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    1.057475] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.20
[    1.057477] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.057479] usb usb3: Product: EHCI Host Controller
[    1.057481] usb usb3: Manufacturer: Linux 4.20.6-arch1-1-ARCH ehci_hcd
[    1.057482] usb usb3: SerialNumber: 0000:00:1d.0
[    1.057619] hub 3-0:1.0: USB hub found
[    1.057630] hub 3-0:1.0: 2 ports detected
[    1.366802] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.371325] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.371360] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.371390] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.372180] ata2.00: supports DRM functions and may not be fully accessible
[    1.372949] ata4.00: ATA-8: TOSHIBA DT01ACA200, MX4OABB0, max UDMA/133
[    1.372955] ata4.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    1.373433] usb 2-3: new full-speed USB device number 2 using xhci_hcd
[    1.373597] ata3.00: ATAPI: ASUS     DRW-24F1ST   a, 1.00, max UDMA/100
[    1.374941] ata3.00: configured for UDMA/100
[    1.375551] ata4.00: configured for UDMA/133
[    1.380257] ata2.00: disabling queued TRIM support
[    1.380263] ata2.00: ATA-9: Crucial_CT256MX100SSD1, MU01, max UDMA/133
[    1.380269] ata2.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    1.386804] usb 3-1: new high-speed USB device number 2 using ehci-pci
[    1.398453] ata2.00: supports DRM functions and may not be fully accessible
[    1.406578] ata2.00: disabling queued TRIM support
[    1.423921] ata2.00: configured for UDMA/133
[    1.424408] scsi 1:0:0:0: Direct-Access     ATA      Crucial_CT256MX1 MU01 PQ: 0 ANSI: 5
[    1.426203] scsi 2:0:0:0: CD-ROM            ASUS     DRW-24F1ST   a   1.00 PQ: 0 ANSI: 5
[    1.478130] scsi 3:0:0:0: Direct-Access     ATA      TOSHIBA DT01ACA2 ABB0 PQ: 0 ANSI: 5
[    1.490817] ata2.00: Enabling discard_zeroes_data
[    1.490856] sd 1:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[    1.490858] sd 1:0:0:0: [sda] 4096-byte physical blocks
[    1.490873] sd 1:0:0:0: [sda] Write Protect is off
[    1.490875] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.490890] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.490938] sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    1.490939] sd 3:0:0:0: [sdb] 4096-byte physical blocks
[    1.490960] sd 3:0:0:0: [sdb] Write Protect is off
[    1.490962] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.490981] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.491017] ata2.00: Enabling discard_zeroes_data
[    1.494471] sr 2:0:0:0: [sr0] scsi3-mmc drive: 16x/16x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.494472] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.494602] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    1.495186]  sda: sda1 sda2 sda3 < sda5 sda6 sda7 > sda4
[    1.495580] ata2.00: Enabling discard_zeroes_data
[    1.495820] sd 1:0:0:0: [sda] supports TCG Opal
[    1.495821] sd 1:0:0:0: [sda] Attached SCSI disk
[    1.507015]  sdb: sdb1 sdb2
[    1.507284] sd 3:0:0:0: [sdb] Attached SCSI disk
[    1.513833] usb 1-1: New USB device found, idVendor=8087, idProduct=8009, bcdDevice= 0.00
[    1.513835] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.513954] hub 1-1:1.0: USB hub found
[    1.514080] hub 1-1:1.0: 6 ports detected
[    1.514752] usb 2-3: New USB device found, idVendor=046d, idProduct=c332, bcdDevice= 3.02
[    1.514754] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.514755] usb 2-3: Product: Gaming Mouse G502
[    1.514757] usb 2-3: Manufacturer: Logitech
[    1.514758] usb 2-3: SerialNumber: 0A6E36723731
[    1.518799] hidraw: raw HID events driver (C) Jiri Kosina
[    1.521310] usbcore: registered new interface driver usbhid
[    1.521311] usbhid: USB HID core driver
[    1.522251] random: fast init done
[    1.522457] input: Logitech Gaming Mouse G502 as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.0/0003:046D:C332.0001/input/input3
[    1.522537] hid-generic 0003:046D:C332.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech Gaming Mouse G502] on usb-0000:00:14.0-3/input0
[    1.522691] input: Logitech Gaming Mouse G502 Keyboard as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.1/0003:046D:C332.0002/input/input4
[    1.533753] usb 3-1: New USB device found, idVendor=8087, idProduct=8001, bcdDevice= 0.00
[    1.533755] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.533984] hub 3-1:1.0: USB hub found
[    1.534075] hub 3-1:1.0: 8 ports detected
[    1.576852] input: Logitech Gaming Mouse G502 Consumer Control as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.1/0003:046D:C332.0002/input/input5
[    1.576885] input: Logitech Gaming Mouse G502 System Control as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.1/0003:046D:C332.0002/input/input6
[    1.577066] hid-generic 0003:046D:C332.0002: input,hiddev0,hidraw1: USB HID v1.11 Keyboard [Logitech Gaming Mouse G502] on usb-0000:00:14.0-3/input1
[    1.636746] usb 2-4: new low-speed USB device number 3 using xhci_hcd
[    1.770099] tsc: Refined TSC clocksource calibration: 3399.996 MHz
[    1.770107] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x31024b3bec5, max_idle_ns: 440795366697 ns
[    1.770136] clocksource: Switched to clocksource tsc
[    1.784689] usb 2-4: New USB device found, idVendor=046d, idProduct=c31f, bcdDevice=87.00
[    1.784692] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.784694] usb 2-4: Product: USB Keyboard
[    1.784695] usb 2-4: Manufacturer: Logitech
[    1.790720] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:14.0/usb2/2-4/2-4:1.0/0003:046D:C31F.0003/input/input9
[    1.846780] hid-generic 0003:046D:C31F.0003: input,hidraw2: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-0000:00:14.0-4/input0
[    1.850908] input: Logitech USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:14.0/usb2/2-4/2-4:1.1/0003:046D:C31F.0004/input/input10
[    1.856131] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[    1.906837] input: Logitech USB Keyboard System Control as /devices/pci0000:00/0000:00:14.0/usb2/2-4/2-4:1.1/0003:046D:C31F.0004/input/input11
[    1.907041] hid-generic 0003:046D:C31F.0004: input,hiddev1,hidraw3: USB HID v1.10 Device [Logitech USB Keyboard] on usb-0000:00:14.0-4/input1
[    1.992131] systemd[1]: systemd 240 running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    2.006894] systemd[1]: Detected architecture x86-64.
[    2.010453] systemd[1]: Set hostname to <Tower>.
[    2.030043] usb 2-9: new full-speed USB device number 4 using xhci_hcd
[    2.052910] systemd[1]: /usr/lib/systemd/system/auditd.service:12: PIDFile= references path below legacy directory /var/run/, updating /var/run/auditd.pid → /run/auditd.pid; please update the unit file accordingly.
[    2.077975] systemd[1]: Listening on udev Kernel Socket.
[    2.080205] systemd[1]: Listening on Process Core Dump Socket.
[    2.080293] systemd[1]: Listening on Journal Audit Socket.
[    2.081529] systemd[1]: Created slice system-getty.slice.
[    2.081668] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    2.081922] systemd[1]: Listening on LVM2 metadata daemon socket.
[    2.094088] EXT4-fs (sda6): re-mounted. Opts: (null)
[    2.096991] random: lvm: uninitialized urandom read (4 bytes read)
[    2.098915] random: systemd-random-: uninitialized urandom read (512 bytes read)
[    2.098988] audit: type=1130 audit(1549452637.766:2): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=lvm2-lvmetad comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.099965] audit: type=1130 audit(1549452637.766:3): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-random-seed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.106864] audit: type=1130 audit(1549452637.776:4): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup-dev comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.122213] audit: type=1130 audit(1549452637.789:5): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journald comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.128614] systemd-journald[310]: Received request to flush runtime journal from PID 1
[    2.130959] audit: type=1130 audit(1549452637.799:6): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udevd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.138188] audit: type=1130 audit(1549452637.806:7): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udev-trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.170532] usb 2-9: New USB device found, idVendor=0451, idProduct=2036, bcdDevice= 1.01
[    2.170534] usb 2-9: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.170536] usb 2-9: Product: General Purpose USB Hub
[    2.171459] hub 2-9:1.0: USB hub found
[    2.171546] hub 2-9:1.0: 3 ports detected
[    2.206881] EDAC ie31200: No ECC support
[    2.209268] i801_smbus 0000:00:1f.3: enabling device (0001 -> 0003)
[    2.209425] i801_smbus 0000:00:1f.3: SPD Write Disable is set
[    2.209448] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[    2.210310] ACPI Warning: SystemIO range 0x0000000000001828-0x000000000000182F conflicts with OpRegion 0x0000000000001800-0x000000000000187F (\PMIO) (20181003/utaddress-213)
[    2.210317] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    2.210343] ACPI Warning: SystemIO range 0x0000000000001C40-0x0000000000001C4F conflicts with OpRegion 0x0000000000001C00-0x0000000000001FFF (\GPR) (20181003/utaddress-213)
[    2.210348] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    2.210350] input: PC Speaker as /devices/platform/pcspkr/input/input12
[    2.210354] ACPI Warning: SystemIO range 0x0000000000001C30-0x0000000000001C3F conflicts with OpRegion 0x0000000000001C00-0x0000000000001C3F (\GPRL) (20181003/utaddress-213)
[    2.210358] ACPI Warning: SystemIO range 0x0000000000001C30-0x0000000000001C3F conflicts with OpRegion 0x0000000000001C00-0x0000000000001FFF (\GPR) (20181003/utaddress-213)
[    2.210362] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    2.210395] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer
[    2.210396] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[    2.210397] RAPL PMU: hw unit of domain package 2^-14 Joules
[    2.210398] RAPL PMU: hw unit of domain dram 2^-14 Joules
[    2.210399] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[    2.210500] ACPI Warning: SystemIO range 0x0000000000001C00-0x0000000000001C2F conflicts with OpRegion 0x0000000000001C00-0x0000000000001C3F (\GPRL) (20181003/utaddress-213)
[    2.210504] ACPI Warning: SystemIO range 0x0000000000001C00-0x0000000000001C2F conflicts with OpRegion 0x0000000000001C00-0x0000000000001FFF (\GPR) (20181003/utaddress-213)
[    2.210510] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    2.210510] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    2.221121] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    2.221122] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.221564] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    2.227990] Linux agpgart interface v0.103
[    2.238448] cryptd: max_cpu_qlen set to 1000
[    2.264379] AVX2 version of gcm_enc/dec engaged.
[    2.264380] AES CTR mode by8 optimization enabled
[    2.265906] iTCO_vendor_support: vendor-support=0
[    2.267719] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[    2.267758] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[    2.272912] mousedev: PS/2 mouse device common for all mice
[    2.285072] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[    2.285074] snd_hda_intel 0000:01:00.1: Force to non-snoop mode
[    2.310381] audit: type=1130 audit(1549452637.979:8): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journal-flush comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.314370] snd_hda_codec_realtek hdaudioC0D2: ALC1150: SKU not ready 0x00000000
[    2.314880] snd_hda_codec_realtek hdaudioC0D2: autoconfig for ALC1150: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[    2.314881] snd_hda_codec_realtek hdaudioC0D2:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    2.314883] snd_hda_codec_realtek hdaudioC0D2:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[    2.314884] snd_hda_codec_realtek hdaudioC0D2:    mono: mono_out=0x0
[    2.314885] snd_hda_codec_realtek hdaudioC0D2:    dig-out=0x11/0x0
[    2.314886] snd_hda_codec_realtek hdaudioC0D2:    inputs:
[    2.314887] snd_hda_codec_realtek hdaudioC0D2:      Front Mic=0x19
[    2.314889] snd_hda_codec_realtek hdaudioC0D2:      Rear Mic=0x18
[    2.314890] snd_hda_codec_realtek hdaudioC0D2:      Line=0x1a
[    2.318647] e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock
[    2.324923] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[    2.324978] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[    2.325021] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[    2.325057] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input17
[    2.325092] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input18
[    2.325123] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input19
[    2.328826] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[    2.329013] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input20
[    2.329058] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input21
[    2.329113] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input22
[    2.329170] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input23
[    2.330062] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input24
[    2.330166] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input25
[    2.330222] input: HDA Intel PCH Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input26
[    2.330276] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input27
[    2.337858] Adding 16880636k swap on /dev/sda7.  Priority:-2 extents:1 across:16880636k SSFS
[    2.395561] [drm] radeon kernel modesetting enabled.
[    2.395610] checking generic (e0000000 7f0000) vs hw (e0000000 10000000)
[    2.395611] fb0: switching to radeondrmfb from VESA VGA
[    2.395629] Console: switching to colour dummy device 80x25
[    2.396413] [drm] initializing kernel modesetting (HAWAII 0x1002:0x67B1 0x174B:0xE283 0x00).
[    2.396438] [drm] doorbell mmio base: 0xF0000000
[    2.396439] [drm] doorbell mmio size: 8388608
[    2.396466] resource sanity check: requesting [mem 0x000c0000-0x000dffff], which spans more than PCI Bus 0000:00 [mem 0x000d0000-0x000d3fff window]
[    2.396470] caller pci_map_rom+0x6a/0x1b0 mapping multiple BARs
[    2.396513] ATOM BIOS: C67111
[    2.396561] radeon 0000:01:00.0: VRAM: 4096M 0x0000000000000000 - 0x00000000FFFFFFFF (4096M used)
[    2.396563] radeon 0000:01:00.0: GTT: 2048M 0x0000000100000000 - 0x000000017FFFFFFF
[    2.396566] [drm] Detected VRAM RAM=4096M, BAR=256M
[    2.396567] [drm] RAM width 512bits DDR
[    2.400050] [TTM] Zone  kernel: Available graphics memory: 8171884 kiB
[    2.400051] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
[    2.400052] [TTM] Initializing pool allocator
[    2.400055] [TTM] Initializing DMA pool allocator
[    2.400071] [drm] radeon: 4096M of VRAM memory ready
[    2.400071] [drm] radeon: 2048M of GTT memory ready.
[    2.400083] [drm] Loading hawaii Microcode
[    2.402956] [drm] Internal thermal controller with fan control
[    2.420751] [drm] radeon: dpm initialized
[    2.421482] [drm] Found UVD firmware Version: 1.64 Family ID: 9
[    2.423696] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 74:d4:35:f8:9a:d9
[    2.423813] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[    2.423849] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF
[    2.424681] [drm] Found VCE firmware/feedback version 40.2.2 / 15!
[    2.424692] [drm] GART: num cpu pages 524288, num gpu pages 524288
[    2.426533] [drm] PCIE gen 3 link speeds already enabled
[    2.428136] e1000e 0000:00:19.0 eno1: renamed from eth0
[    2.441077] [drm] PCIE GART of 2048M enabled (table at 0x000000000030E000).
[    2.441242] radeon 0000:01:00.0: WB enabled
[    2.441254] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000100000c00 and cpu addr 0x00000000d3f2c51c
[    2.441256] radeon 0000:01:00.0: fence driver on ring 1 use gpu addr 0x0000000100000c04 and cpu addr 0x000000008a5011f3
[    2.441258] radeon 0000:01:00.0: fence driver on ring 2 use gpu addr 0x0000000100000c08 and cpu addr 0x0000000082d6065b
[    2.441260] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000100000c0c and cpu addr 0x0000000051c8eb61
[    2.441262] radeon 0000:01:00.0: fence driver on ring 4 use gpu addr 0x0000000100000c10 and cpu addr 0x00000000a31ce644
[    2.441623] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x0000000000078d30 and cpu addr 0x00000000d48b2324
[    2.441764] radeon 0000:01:00.0: fence driver on ring 6 use gpu addr 0x0000000100000c18 and cpu addr 0x00000000f0f7b6ba
[    2.441766] radeon 0000:01:00.0: fence driver on ring 7 use gpu addr 0x0000000100000c1c and cpu addr 0x000000006421fd00
[    2.441768] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.441768] [drm] Driver supports precise vblank timestamp query.
[    2.441812] radeon 0000:01:00.0: radeon: using MSI.
[    2.441832] [drm] radeon: irq initialized.
[    2.444210] [drm] ring test on 0 succeeded in 3 usecs
[    2.444279] [drm] ring test on 1 succeeded in 3 usecs
[    2.444291] [drm] ring test on 2 succeeded in 3 usecs
[    2.444463] [drm] ring test on 3 succeeded in 4 usecs
[    2.444469] [drm] ring test on 4 succeeded in 4 usecs
[    2.450059] usb 2-9.2: new full-speed USB device number 5 using xhci_hcd
[    2.460030] intel_rapl: Found RAPL domain package
[    2.460032] intel_rapl: Found RAPL domain core
[    2.460033] intel_rapl: Found RAPL domain dram
[    2.490519] [drm] ring test on 5 succeeded in 2 usecs
[    2.510540] [drm] UVD initialized successfully.
[    2.545250] usb 2-9.2: New USB device found, idVendor=1038, idProduct=1290, bcdDevice= 6.00
[    2.545251] usb 2-9.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.545252] usb 2-9.2: Product: Arctis Pro Wireless
[    2.545253] usb 2-9.2: Manufacturer: SteelSeries
[    2.546577] hid-generic 0003:1038:1290.0005: hiddev2,hidraw4: USB HID v1.11 Device [SteelSeries Arctis Pro Wireless] on usb-0000:00:14.0-9.2/input0
[    2.547072] hid-generic 0003:1038:1290.0006: hiddev3,hidraw5: USB HID v1.11 Device [SteelSeries Arctis Pro Wireless] on usb-0000:00:14.0-9.2/input1
[    2.597828] audit: type=1130 audit(1549452638.266:9): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=lvm2-monitor comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.620046] usb 2-9.3: new full-speed USB device number 6 using xhci_hcd
[    2.620672] [drm] ring test on 6 succeeded in 24 usecs
[    2.620680] [drm] ring test on 7 succeeded in 3 usecs
[    2.620681] [drm] VCE initialized successfully.
[    2.621579] [drm] ib test on ring 0 succeeded in 0 usecs
[    2.621714] [drm] ib test on ring 1 succeeded in 0 usecs
[    2.621847] [drm] ib test on ring 2 succeeded in 0 usecs
[    2.621981] [drm] ib test on ring 3 succeeded in 0 usecs
[    2.622113] [drm] ib test on ring 4 succeeded in 0 usecs
[    2.625275] audit: type=1130 audit(1549452638.292:10): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-fsck@dev-disk-by\x2duuid-b6d2fa8c\x2db772\x2d42f2\x2d9f5e\x2d305e4790f9c1 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.633963] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: stripe=4
[    2.690187] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[    2.710960] random: dbus-daemon: uninitialized urandom read (12 bytes read)
[    2.724370] usb 2-9.3: New USB device found, idVendor=1038, idProduct=1294, bcdDevice= 1.10
[    2.724382] usb 2-9.3: New USB device strings: Mfr=4, Product=5, SerialNumber=0
[    2.724383] usb 2-9.3: Product: Arctis Pro Wireless
[    2.724384] usb 2-9.3: Manufacturer: SteelSeries 
[    2.738232] input: SteelSeries  Arctis Pro Wireless Consumer Control as /devices/pci0000:00/0000:00:14.0/usb2/2-9/2-9.3/2-9.3:1.5/0003:1038:1294.0007/input/input28
[    2.793609] input: SteelSeries  Arctis Pro Wireless as /devices/pci0000:00/0000:00:14.0/usb2/2-9/2-9.3/2-9.3:1.5/0003:1038:1294.0007/input/input29
[    2.793809] hid-generic 0003:1038:1294.0007: input,hiddev4,hidraw6: USB HID v1.11 Device [SteelSeries  Arctis Pro Wireless] on usb-0000:00:14.0-9.3/input5
[    2.843050] usb 2-9.3: 4:1: cannot set freq 48000 to ep 0x2
[    2.843682] usb 2-9.3: 4:2: cannot set freq 48000 to ep 0x2
[    2.844789] usb 2-9.3: 2:0: cannot get min/max values for control 2 (id 2)
[    2.844889] usbcore: registered new interface driver snd-usb-audio
[    2.914296] usb 2-9.3: USB disconnect, device number 6
[    3.000252] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[    3.156859] [drm] ib test on ring 5 succeeded
[    3.177833] [drm] ib test on ring 6 succeeded
[    3.178653] [drm] ib test on ring 7 succeeded
[    3.179036] [drm] Radeon Display Connectors
[    3.179037] [drm] Connector 0:
[    3.179038] [drm]   DP-1
[    3.179038] [drm]   HPD2
[    3.179039] [drm]   DDC: 0x6530 0x6530 0x6534 0x6534 0x6538 0x6538 0x653c 0x653c
[    3.179039] [drm]   Encoders:
[    3.179040] [drm]     DFP1: INTERNAL_UNIPHY2
[    3.179040] [drm] Connector 1:
[    3.179041] [drm]   HDMI-A-1
[    3.179041] [drm]   HPD3
[    3.179042] [drm]   DDC: 0x6550 0x6550 0x6554 0x6554 0x6558 0x6558 0x655c 0x655c
[    3.179042] [drm]   Encoders:
[    3.179042] [drm]     DFP2: INTERNAL_UNIPHY2
[    3.179043] [drm] Connector 2:
[    3.179043] [drm]   DVI-D-1
[    3.179043] [drm]   HPD1
[    3.179044] [drm]   DDC: 0x6560 0x6560 0x6564 0x6564 0x6568 0x6568 0x656c 0x656c
[    3.179045] [drm]   Encoders:
[    3.179045] [drm]     DFP3: INTERNAL_UNIPHY1
[    3.179045] [drm] Connector 3:
[    3.179046] [drm]   DVI-D-2
[    3.179046] [drm]   HPD6
[    3.179047] [drm]   DDC: 0x6580 0x6580 0x6584 0x6584 0x6588 0x6588 0x658c 0x658c
[    3.179047] [drm]   Encoders:
[    3.179047] [drm]     DFP4: INTERNAL_UNIPHY
[    3.200066] usb 2-9.3: new full-speed USB device number 7 using xhci_hcd
[    3.213548] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[    3.239061] urandom_read: 2 callbacks suppressed
[    3.239062] random: polkitd: uninitialized urandom read (8 bytes read)
[    3.239452] random: polkitd: uninitialized urandom read (8 bytes read)
[    3.239455] random: polkitd: uninitialized urandom read (8 bytes read)
[    3.281828] snd_hda_codec_hdmi hdaudioC1D0: HDMI ATI/AMD: no speaker allocation for ELD
[    3.285407] [drm] fb mappable at 0xE0721000
[    3.285408] [drm] vram apper at 0xE0000000
[    3.285409] [drm] size 8294400
[    3.285409] [drm] fb depth is 24
[    3.285409] [drm]    pitch is 7680
[    3.285526] fbcon: radeondrmfb (fb0) is primary device
[    3.312157] Console: switching to colour frame buffer device 240x67
[    3.316000] usb 2-9.3: New USB device found, idVendor=1038, idProduct=1294, bcdDevice= 1.10
[    3.316002] usb 2-9.3: New USB device strings: Mfr=4, Product=5, SerialNumber=0
[    3.316004] usb 2-9.3: Product: Arctis Pro Wireless
[    3.316005] usb 2-9.3: Manufacturer: SteelSeries 
[    3.316353] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[    3.345820] [drm] Initialized radeon 2.50.0 20080528 for 0000:01:00.0 on minor 0
[    3.352227] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[    3.352228] AMD IOMMUv2 functionality not available on this system
[    3.493647] [drm] amdgpu kernel modesetting enabled.
[    3.493684] CRAT table not found
[    3.493686] Virtual CRAT table created for CPU
[    3.493687] Parsing CRAT table with 1 nodes
[    3.493688] Creating topology SYSFS entries
[    3.493694] Topology: Add CPU node
[    3.493694] Finished initializing topology
[    3.598422] input: SteelSeries  Arctis Pro Wireless Consumer Control as /devices/pci0000:00/0000:00:14.0/usb2/2-9/2-9.3/2-9.3:1.5/0003:1038:1294.0008/input/input30
[    3.653579] input: SteelSeries  Arctis Pro Wireless as /devices/pci0000:00/0000:00:14.0/usb2/2-9/2-9.3/2-9.3:1.5/0003:1038:1294.0008/input/input31
[    3.653692] hid-generic 0003:1038:1294.0008: input,hiddev4,hidraw6: USB HID v1.11 Device [SteelSeries  Arctis Pro Wireless] on usb-0000:00:14.0-9.3/input5
[    5.362382] random: crng init done
[    5.362387] random: 2 urandom warning(s) missed due to ratelimiting
[    6.128834] e1000e: eno1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[    6.128871] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready
[    6.878841] kauditd_printk_skb: 12 callbacks suppressed
[    6.878842] audit: type=1006 audit(1549452642.546:23): pid=518 uid=0 old-auid=4294967295 auid=1000 tty=tty1 old-ses=4294967295 ses=1 res=1
[    6.897012] audit: type=1130 audit(1549452642.566:24): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user-runtime-dir@1000 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    6.901156] audit: type=1006 audit(1549452642.569:25): pid=556 uid=0 old-auid=4294967295 auid=1000 tty=(none) old-ses=4294967295 ses=2 res=1
[    6.933837] audit: type=1130 audit(1549452642.602:26): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user@1000 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    8.707024] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[   13.009585] audit: type=1131 audit(1549452648.679:27): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-dispatcher comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   17.707283] audit: type=1130 audit(1549452653.376:28): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=rtkit-daemon comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   33.011157] audit: type=1131 audit(1549452668.679:29): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   98.423557] radeon_dp_aux_transfer_native: 158 callbacks suppressed
[  171.186909] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  214.123592] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  301.906900] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  361.676848] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  488.386847] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  577.420253] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  593.810172] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  650.730138] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  679.383542] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  747.190174] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  768.833454] radeon_dp_aux_transfer_native: 74 callbacks suppressed
[  907.649854] audit: type=1130 audit(1549453543.316:30): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-clean comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  907.649856] audit: type=1131 audit(1549453543.316:31): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-clean comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 7131.462315] radeon_dp_aux_transfer_native: 74 callbacks suppressed

Should I proceed with what is written in your wiki link?

seth · 2019-02-06 13:56:38

You can try.
If it fails, try to add "module_blacklist=radeon" instead. Did you previously add the radeon module to the initramfs?

Edit: the "safe" way to do this is to alter the kernel parameters at the bootloader commandline, rather than editing the bootloaders config (if something goes wrong, you just have to reboot)

Last edited by seth (2019-02-06 13:58:13)

Sito · 2019-02-06 14:52:01

You can try.
If it fails, try to add "module_blacklist=radeon" instead. Did you previously add the radeon module to the initramfs?

I rebooted and entred the grub-commandline using 'c'.. Typed in

radeon.si_support=0 amdgpu.si_support=1
radeon.cik_support=0 amdgpu.cik_support=1

and booted up. 'lspci -v ' showed the same settings as in first post... I then again rebooted and this time tried 'module_blacklist=radeon', but again 'lspci -v' gives the same result.

Did I do something wrong, I'm not really familiar with the bootloader commandline...

seth · 2019-02-06 14:54:40

You can check "cat /proc/cmdline"

seth wrote:

Did you previously add the radeon module to the initramfs?

Sito · 2019-02-06 15:01:12

$ cat /proc/cmdline
BOOT_IMAGE=(hd0,msdos5)/vmlinuz-linux root=/dev/sda6

Did you previously add the radeon module to the initramfs?

I'm sorry, but I can't really remember.. But it's certainly possible that I did that while trying to solve the issue on my own...

seth · 2019-02-06 15:07:20

lsinitcpio /boot/initramfs-linux.img | grep radeon

What wrote your grub.conf? That doesn't look like a grub-mkconfig token.

Sito · 2019-02-06 15:16:38

I run

lsinitcpio /boot/initramfs-linux.img | grep radeon

didn't get any message back. Rebooted, but no change regarding the drivers.

What wrote your grub.conf? That doesn't look like a grub-mkconfig token.

The base was produced with

grub-install --target=i386-pc /dev/sda
grub-mkconfig -o /boot/grub/grub.cfg

but since this pc is a dual boot with windows 10 in legacy mode I added manually

if [ "${grub_platform}" == "pc" ]; then
	menuentry "Microsoft Windows Vista/7/8/8.1/10 BIOS/MBR" {
		insmod part_msdos
		insmod ntfs
		insmod ntldr     
		search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 XXXXXXXXXXXXXXXX
		ntldr /bootmgr
	}
fi

where XXXXXXXXXXXXXXXX stands for the UUID (directly taken from here from the dual boot section)

Last edited by Sito (2019-02-06 15:17:16)

seth · 2019-02-06 16:20:49

Ftr, the commandline you posted does not suggest any additional parameters (neither the blacklist nor the SI/CIK manipulation)

Arch Linux

#1 2019-02-05 20:06:37

Lagging graphics when watching videos and browsing with Firefox

#2 2019-02-05 20:40:48

Re: Lagging graphics when watching videos and browsing with Firefox

#3 2019-02-05 23:38:06

Re: Lagging graphics when watching videos and browsing with Firefox

#4 2019-02-06 11:12:46

Re: Lagging graphics when watching videos and browsing with Firefox

#5 2019-02-06 11:34:07

Re: Lagging graphics when watching videos and browsing with Firefox

#6 2019-02-06 12:52:14

Re: Lagging graphics when watching videos and browsing with Firefox

#7 2019-02-06 13:51:26

Re: Lagging graphics when watching videos and browsing with Firefox

#8 2019-02-06 13:56:38

Re: Lagging graphics when watching videos and browsing with Firefox

#9 2019-02-06 14:52:01

Re: Lagging graphics when watching videos and browsing with Firefox

#10 2019-02-06 14:54:40

Re: Lagging graphics when watching videos and browsing with Firefox

#11 2019-02-06 15:01:12

Re: Lagging graphics when watching videos and browsing with Firefox

#12 2019-02-06 15:07:20

Re: Lagging graphics when watching videos and browsing with Firefox

#13 2019-02-06 15:16:38

Re: Lagging graphics when watching videos and browsing with Firefox

#14 2019-02-06 16:20:49

Re: Lagging graphics when watching videos and browsing with Firefox

Board footer