You are not logged in.

#1 2020-11-20 03:51:48

jekb
Member
Registered: 2020-11-20
Posts: 2

Radeon 6800 / 6800XT graphics

hi,

has anyone managed to get the new AMD radeon cards working in Arch? I am using the 6800XT

I'm on kernel 5.9 and have installed linux-firmware-git and mesa-git. however I still cannot get xorg to launch. my xorg log shows the following errors:

open /dev/dri/card0: No such file or directory
Screen 0 deleted because of no matching config section.
Devices detected, but none match those in the config file
Fatal server error:
    no screens found

my card does show up in lspci:

2d:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 73bf (rev c1)

am I missing a step? has anyone else managed to get these cards working?
thank you

Last edited by jekb (2020-11-20 03:52:10)

Offline

#2 2020-11-20 04:15:12

loqs
Member
Registered: 2014-03-06
Posts: 12,134

Re: Radeon 6800 / 6800XT graphics

What is the pkgver of linux-firmware-git?  Please post the full contents of Xorg.0.log and the output of dmesg.
Edit:
See also the Linux 5.9+ section of https://www.phoronix.com/scan.php?page= … inux&num=2

Last edited by loqs (2020-11-20 04:51:00)

Offline

#3 2020-11-20 16:34:42

Handl3vogn
Member
Registered: 2020-11-20
Posts: 8

Re: Radeon 6800 / 6800XT graphics

Also getting problems with my 6800XT

getting this error

[    0.056080] APIC: Switch to symmetric I/O mode setup
[    0.056081] DMAR: Host address width 39
[    0.056082] DMAR: DRHD base: 0x000000fed90000 flags: 0x1
[    0.056085] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap d2008c40660462 ecap f050da
[    0.056086] DMAR: RMRR base: 0x000000bdf93000 end: 0x000000bdfb2fff
[    0.056087] DMAR-IR: IOAPIC id 2 under DRHD base  0xfed90000 IOMMU 0
[    0.056088] DMAR-IR: HPET id 0 under DRHD base 0xfed90000
[    0.056088] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
[    0.057376] DMAR-IR: Enabled IRQ remapping in x2apic mode
[    0.057376] x2apic enabled
[    0.057388] Switched APIC routing to cluster x2apic.
[    0.061514] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.076056] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x3c8a615336c, max_idle_ns: 440795257976 ns
[    0.076058] Calibrating delay loop (skipped), value calculated using timer frequency.. 8403.00 BogoMIPS (lpj=14000000)
[    0.076059] pid_max: default: 32768 minimum: 301
[    0.079365] LSM: Security Framework initializing
[    0.079367] Yama: becoming mindful.
[    0.079394] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.079409] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.079562] mce: CPU0: Thermal monitoring enabled (TM1)
[    0.079574] process: using mwait in idle threads
[    0.079575] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
[    0.079575] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[    0.079577] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.079578] Spectre V2 : Mitigation: Full generic retpoline
[    0.079578] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.079578] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.079579] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.079579] Spectre V2 : User space: Mitigation: STIBP via seccomp and prctl
[    0.079579] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[    0.079581] TAA: Mitigation: Clear CPU buffers
[    0.079582] SRBDS: Mitigation: Microcode
[    0.079583] MDS: Mitigation: Clear CPU buffers
[    0.079731] Freeing SMP alternatives memory: 32K
[    0.080428] smpboot: CPU0: Intel(R) Core(TM) i7-7700K CPU @ 4.20GHz (family: 0x6, model: 0x9e, stepping: 0x9)
[    0.080477] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver.
[    0.080482] ... version:                4
[    0.080483] ... bit width:              48
[    0.080483] ... generic registers:      4
[    0.080483] ... value mask:             0000ffffffffffff
[    0.080483] ... max period:             00007fffffffffff
[    0.080484] ... fixed-purpose events:   3
[    0.080484] ... event mask:             000000070000000f
[    0.080507] rcu: Hierarchical SRCU implementation.
[    0.080841] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.080883] smp: Bringing up secondary CPUs ...
[    0.080938] x86: Booting SMP configuration:
[    0.080938] .... node  #0, CPUs:      #1 #2 #3 #4
[    0.084031] MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details.
[    0.084031] TAA CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/tsx_async_abort.html for more details.
[    0.084031]  #5 #6 #7
[    0.084031] smp: Brought up 1 node, 8 CPUs
[    0.084031] smpboot: Max logical packages: 1
[    0.084031] smpboot: Total of 8 processors activated (67226.00 BogoMIPS)
[    0.086293] devtmpfs: initialized
[    0.086293] x86/mm: Memory block size: 128MB
[    0.086658] PM: Registering ACPI NVS region [mem 0xb4ade000-0xb4adefff] (4096 bytes)
[    0.086658] PM: Registering ACPI NVS region [mem 0xbe1ae000-0xbe85ffff] (7020544 bytes)
[    0.086659] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.086659] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.086659] pinctrl core: initialized pinctrl subsystem
[    0.086659] PM: RTC time: 19:15:04, date: 2020-11-20
[    0.086659] NET: Registered protocol family 16
[    0.086659] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    0.086659] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.086659] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.086659] audit: initializing netlink subsys (disabled)
[    0.086659] audit: type=2000 audit(1605899704.029:1): state=initialized audit_enabled=0 res=1
[    0.086659] thermal_sys: Registered thermal governor 'fair_share'
[    0.086659] thermal_sys: Registered thermal governor 'bang_bang'
[    0.086659] thermal_sys: Registered thermal governor 'step_wise'
[    0.086659] thermal_sys: Registered thermal governor 'user_space'
[    0.086659] thermal_sys: Registered thermal governor 'power_allocator'
[    0.086659] cpuidle: using governor ladder
[    0.086659] cpuidle: using governor menu
[    0.086659] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.086659] ACPI: bus type PCI registered
[    0.086659] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.086659] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[    0.086659] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[    0.086659] PCI: Using configuration type 1 for base access
[    0.086966] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.086966] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.086966] ACPI: Added _OSI(Module Device)
[    0.086966] ACPI: Added _OSI(Processor Device)
[    0.086966] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.086966] ACPI: Added _OSI(Processor Aggregator Device)
[    0.086966] ACPI: Added _OSI(Linux-Dell-Video)
[    0.086966] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.086966] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.114149] ACPI: 9 ACPI AML tables successfully acquired and loaded
[    0.116148] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.119391] ACPI: Dynamic OEM Table Load:
[    0.119391] ACPI: SSDT 0xFFFF89AAACA74000 00081F (v02 PmRef  Cpu0Ist  00003000 INTL 20160422)
[    0.120116] ACPI: \_PR_.CPU0: _OSC native thermal LVT Acked
[    0.121243] ACPI: Dynamic OEM Table Load:
[    0.121246] ACPI: SSDT 0xFFFF89AAACA21800 00065C (v02 PmRef  ApIst    00003000 INTL 20160422)
[    0.124914] ACPI: Interpreter enabled
[    0.124938] ACPI: (supports S0 S3 S4 S5)
[    0.124939] ACPI: Using IOAPIC for interrupt routing
[    0.124962] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.125682] ACPI: Enabled 8 GPEs in block 00 to 7F
[    0.127414] ACPI: Power Resource [PG00] (on)
[    0.127721] ACPI: Power Resource [PG01] (on)
[    0.128018] ACPI: Power Resource [PG02] (on)
[    0.129407] ACPI: Power Resource [WRST] (on)
[    0.129649] ACPI: Power Resource [WRST] (on)
[    0.129891] ACPI: Power Resource [WRST] (on)
[    0.130129] ACPI: Power Resource [WRST] (on)
[    0.130367] ACPI: Power Resource [WRST] (on)
[    0.130607] ACPI: Power Resource [WRST] (on)
[    0.130935] ACPI: Power Resource [WRST] (on)
[    0.131173] ACPI: Power Resource [WRST] (on)
[    0.131413] ACPI: Power Resource [WRST] (on)
[    0.131653] ACPI: Power Resource [WRST] (on)
[    0.131893] ACPI: Power Resource [WRST] (on)
[    0.132147] ACPI: Power Resource [WRST] (on)
[    0.132389] ACPI: Power Resource [WRST] (on)
[    0.132687] ACPI: Power Resource [WRST] (on)
[    0.132930] ACPI: Power Resource [WRST] (on)
[    0.133169] ACPI: Power Resource [WRST] (on)
[    0.133406] ACPI: Power Resource [WRST] (on)
[    0.134310] ACPI: Power Resource [WRST] (on)
[    0.134548] ACPI: Power Resource [WRST] (on)
[    0.134784] ACPI: Power Resource [WRST] (on)
[    0.144511] ACPI: Power Resource [FN00] (off)
[    0.144573] ACPI: Power Resource [FN01] (off)
[    0.144633] ACPI: Power Resource [FN02] (off)
[    0.144692] ACPI: Power Resource [FN03] (off)
[    0.144755] ACPI: Power Resource [FN04] (off)
[    0.145619] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])
[    0.145623] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
[    0.145649] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.146208] PCI host bridge to bus 0000:00
[    0.146209] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.146210] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.146210] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.146211] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xefffffff window]
[    0.146211] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfe7fffff window]
[    0.146212] pci_bus 0000:00: root bus resource [bus 00-7e]
[    0.146221] pci 0000:00:00.0: [8086:591f] type 00 class 0x060000
[    0.146468] pci 0000:00:01.0: [8086:1901] type 01 class 0x060400
[    0.146497] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.146715] pci 0000:00:08.0: [8086:1911] type 00 class 0x088000
[    0.146721] pci 0000:00:08.0: reg 0x10: [mem 0xefe4e000-0xefe4efff 64bit]
[    0.146844] pci 0000:00:14.0: [8086:a2af] type 00 class 0x0c0330
[    0.146857] pci 0000:00:14.0: reg 0x10: [mem 0xefe30000-0xefe3ffff 64bit]
[    0.146908] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.147148] pci 0000:00:16.0: [8086:a2ba] type 00 class 0x078000
[    0.147164] pci 0000:00:16.0: reg 0x10: [mem 0xefe4d000-0xefe4dfff 64bit]
[    0.147209] pci 0000:00:16.0: PME# supported from D3hot
[    0.147365] pci 0000:00:17.0: [8086:a282] type 00 class 0x010601
[    0.147374] pci 0000:00:17.0: reg 0x10: [mem 0xefe48000-0xefe49fff]
[    0.147379] pci 0000:00:17.0: reg 0x14: [mem 0xefe4c000-0xefe4c0ff]
[    0.147384] pci 0000:00:17.0: reg 0x18: [io  0xf050-0xf057]
[    0.147389] pci 0000:00:17.0: reg 0x1c: [io  0xf040-0xf043]
[    0.147394] pci 0000:00:17.0: reg 0x20: [io  0xf020-0xf03f]
[    0.147399] pci 0000:00:17.0: reg 0x24: [mem 0xefe4b000-0xefe4b7ff]
[    0.147429] pci 0000:00:17.0: PME# supported from D3hot
[    0.147568] pci 0000:00:1b.0: [8086:a2e7] type 01 class 0x060400
[    0.147618] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.147827] pci 0000:00:1b.4: [8086:a2eb] type 01 class 0x060400
[    0.147885] pci 0000:00:1b.4: PME# supported from D0 D3hot D3cold
[    0.148095] pci 0000:00:1c.0: [8086:a290] type 01 class 0x060400
[    0.148148] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.148357] pci 0000:00:1c.5: [8086:a295] type 01 class 0x060400
[    0.148409] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.148603] pci 0000:00:1c.6: [8086:a296] type 01 class 0x060400
[    0.148655] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[    0.148849] pci 0000:00:1c.7: [8086:a297] type 01 class 0x060400
[    0.148900] pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
[    0.149095] pci 0000:00:1d.0: [8086:a298] type 01 class 0x060400
[    0.149153] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.149366] pci 0000:00:1d.5: [8086:a29d] type 01 class 0x060400
[    0.149419] pci 0000:00:1d.5: PME# supported from D0 D3hot D3cold
[    0.149621] pci 0000:00:1f.0: [8086:a2c5] type 00 class 0x060100
[    0.149837] pci 0000:00:1f.2: [8086:a2a1] type 00 class 0x058000
[    0.149849] pci 0000:00:1f.2: reg 0x10: [mem 0xefe44000-0xefe47fff]
[    0.150021] pci 0000:00:1f.3: [8086:a2f0] type 00 class 0x040300
[    0.150040] pci 0000:00:1f.3: reg 0x10: [mem 0xefe40000-0xefe43fff 64bit]
[    0.150066] pci 0000:00:1f.3: reg 0x20: [mem 0xefe20000-0xefe2ffff 64bit]
[    0.150107] pci 0000:00:1f.3: PME# supported from D3hot D3cold
[    0.150327] pci 0000:00:1f.4: [8086:a2a3] type 00 class 0x0c0500
[    0.150383] pci 0000:00:1f.4: reg 0x10: [mem 0xefe4a000-0xefe4a0ff 64bit]
[    0.150451] pci 0000:00:1f.4: reg 0x20: [io  0xf000-0xf01f]
[    0.150657] pci 0000:00:1f.6: [8086:15b8] type 00 class 0x020000
[    0.150673] pci 0000:00:1f.6: reg 0x10: [mem 0xefe00000-0xefe1ffff]
[    0.150765] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
[    0.150928] pci 0000:01:00.0: [1002:1478] type 01 class 0x060400
[    0.150938] pci 0000:01:00.0: reg 0x10: [mem 0xefa00000-0xefa03fff]
[    0.151006] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.151050] pci 0000:01:00.0: 126.016 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x16 link at 0000:00:01.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[    0.151099] pci 0000:00:01.0: PCI bridge to [bus 01-03]
[    0.151100] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.151102] pci 0000:00:01.0:   bridge window [mem 0xef700000-0xefafffff]
[    0.151103] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.151138] pci 0000:02:00.0: [1002:1479] type 01 class 0x060400
[    0.151212] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    0.151277] pci 0000:01:00.0: PCI bridge to [bus 02-03]
[    0.151281] pci 0000:01:00.0:   bridge window [io  0xe000-0xefff]
[    0.151282] pci 0000:01:00.0:   bridge window [mem 0xef700000-0xef9fffff]
[    0.151286] pci 0000:01:00.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.151320] pci 0000:03:00.0: [1002:73bf] type 00 class 0x030000
[    0.151332] pci 0000:03:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.151339] pci 0000:03:00.0: reg 0x18: [mem 0xe0000000-0xe01fffff 64bit pref]
[    0.151344] pci 0000:03:00.0: reg 0x20: [io  0xe000-0xe0ff]
[    0.151349] pci 0000:03:00.0: reg 0x24: [mem 0xef800000-0xef8fffff]
[    0.151354] pci 0000:03:00.0: reg 0x30: [mem 0xef900000-0xef91ffff pref]
[    0.151367] pci 0000:03:00.0: BAR 0: assigned to efifb
[    0.151410] pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.151456] pci 0000:03:00.0: 126.016 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x16 link at 0000:00:01.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[    0.151486] pci 0000:03:00.1: [1002:ab28] type 00 class 0x040300
[    0.151495] pci 0000:03:00.1: reg 0x10: [mem 0xef924000-0xef927fff]
[    0.151562] pci 0000:03:00.1: PME# supported from D1 D2 D3hot D3cold
[    0.151611] pci 0000:03:00.2: [1002:73a6] type 00 class 0x0c0330
[    0.151622] pci 0000:03:00.2: reg 0x10: [mem 0xef700000-0xef7fffff 64bit]
[    0.151689] pci 0000:03:00.2: PME# supported from D0 D3hot D3cold
[    0.151737] pci 0000:03:00.3: [1002:73a4] type 00 class 0x0c8000
[    0.151748] pci 0000:03:00.3: reg 0x10: [mem 0xef920000-0xef923fff 64bit]
[    0.151811] pci 0000:03:00.3: PME# supported from D0 D3hot
[    0.151884] pci 0000:02:00.0: PCI bridge to [bus 03]
[    0.151887] pci 0000:02:00.0:   bridge window [io  0xe000-0xefff]
[    0.151889] pci 0000:02:00.0:   bridge window [mem 0xef700000-0xef9fffff]
[    0.151892] pci 0000:02:00.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.151977] pci 0000:04:00.0: [144d:a808] type 00 class 0x010802
[    0.151993] pci 0000:04:00.0: reg 0x10: [mem 0xefd00000-0xefd03fff 64bit]
[    0.152225] pci 0000:00:1b.0: PCI bridge to [bus 04]
[    0.152227] pci 0000:00:1b.0:   bridge window [mem 0xefd00000-0xefdfffff]
[    0.152294] pci 0000:00:1b.4: PCI bridge to [bus 05]
[    0.152380] pci 0000:06:00.0: [1b21:2142] type 00 class 0x0c0330
[    0.152398] pci 0000:06:00.0: reg 0x10: [mem 0xefc00000-0xefc07fff 64bit]
[    0.152438] pci 0000:06:00.0: enabling Extended Tags
[    0.152495] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[    0.152636] pci 0000:00:1c.0: PCI bridge to [bus 06]
[    0.152639] pci 0000:00:1c.0:   bridge window [mem 0xefc00000-0xefcfffff]
[    0.152725] pci 0000:07:00.0: [1969:e0b1] type 00 class 0x020000
[    0.152746] pci 0000:07:00.0: reg 0x10: [mem 0xefb00000-0xefb3ffff 64bit]
[    0.152755] pci 0000:07:00.0: reg 0x18: [io  0xd000-0xd07f]
[    0.152851] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.152986] pci 0000:00:1c.5: PCI bridge to [bus 07]
[    0.152987] pci 0000:00:1c.5:   bridge window [io  0xd000-0xdfff]
[    0.152989] pci 0000:00:1c.5:   bridge window [mem 0xefb00000-0xefbfffff]
[    0.153052] pci 0000:00:1c.6: PCI bridge to [bus 08]
[    0.153114] pci 0000:00:1c.7: PCI bridge to [bus 09]
[    0.153179] pci 0000:00:1d.0: PCI bridge to [bus 0a]
[    0.153264] pci 0000:0b:00.0: [14e4:43a0] type 00 class 0x028000
[    0.153282] pci 0000:0b:00.0: reg 0x10: [mem 0xef600000-0xef607fff 64bit]
[    0.153293] pci 0000:0b:00.0: reg 0x18: [mem 0xef400000-0xef5fffff 64bit]
[    0.153390] pci 0000:0b:00.0: supports D1 D2
[    0.153390] pci 0000:0b:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.153553] pci 0000:00:1d.5: PCI bridge to [bus 0b]
[    0.153556] pci 0000:00:1d.5:   bridge window [mem 0xef400000-0xef6fffff]
[    0.154995] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155036] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[    0.155076] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155116] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155155] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155194] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155234] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155274] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.156115] iommu: Default domain type: Translated 
[    0.156124] pci 0000:03:00.0: vgaarb: setting as boot VGA device
[    0.156124] pci 0000:03:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.156124] pci 0000:03:00.0: vgaarb: bridge control possible
[    0.156124] vgaarb: loaded
[    0.156152] SCSI subsystem initialized
[    0.156161] libata version 3.00 loaded.
[    0.156161] ACPI: bus type USB registered
[    0.156161] usbcore: registered new interface driver usbfs
[    0.156161] usbcore: registered new interface driver hub
[    0.156161] usbcore: registered new device driver usb
[    0.156161] pps_core: LinuxPPS API ver. 1 registered
[    0.156161] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.156161] PTP clock support registered
[    0.156161] EDAC MC: Ver: 3.0.0
[    0.156163] Registered efivars operations
[    0.156163] NetLabel: Initializing
[    0.156163] NetLabel:  domain hash size = 128
[    0.156163] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.156163] NetLabel:  unlabeled traffic allowed by default
[    0.156163] PCI: Using ACPI for IRQ routing
[    0.169333] PCI: pci_cache_line_size set to 64 bytes
[    0.169386] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
[    0.169387] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[    0.169387] e820: reserve RAM buffer [mem 0xb32a2018-0xb3ffffff]
[    0.169388] e820: reserve RAM buffer [mem 0xb32b3018-0xb3ffffff]
[    0.169388] e820: reserve RAM buffer [mem 0xb32c0018-0xb3ffffff]
[    0.169389] e820: reserve RAM buffer [mem 0xb4ade000-0xb7ffffff]
[    0.169389] e820: reserve RAM buffer [mem 0xb9c18000-0xbbffffff]
[    0.169390] e820: reserve RAM buffer [mem 0xbc6e2000-0xbfffffff]
[    0.169391] e820: reserve RAM buffer [mem 0xbdcc6000-0xbfffffff]
[    0.169391] e820: reserve RAM buffer [mem 0xbe1ae000-0xbfffffff]
[    0.169392] e820: reserve RAM buffer [mem 0xbf800000-0xbfffffff]
[    0.169392] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff]
[    0.169774] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.169776] hpet0: 8 comparators, 64-bit 24.000000 MHz counter
[    0.171829] clocksource: Switched to clocksource tsc-early
[    0.175482] VFS: Disk quotas dquot_6.6.0
[    0.175482] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.175482] pnp: PnP ACPI init
[    0.175482] system 00:00: [io  0x0a00-0x0a2f] has been reserved
[    0.175482] system 00:00: [io  0x0a30-0x0a3f] has been reserved
[    0.175482] system 00:00: [io  0x0a40-0x0a4f] has been reserved
[    0.175482] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.175482] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.175482] system 00:01: [io  0xffff] has been reserved
[    0.175482] system 00:01: [io  0xffff] has been reserved
[    0.175482] system 00:01: [io  0xffff] has been reserved
[    0.175482] system 00:01: [io  0x1800-0x18fe] has been reserved
[    0.175482] system 00:01: [io  0x164e-0x164f] has been reserved
[    0.175482] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.175482] system 00:02: [io  0x0800-0x087f] has been reserved
[    0.175482] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.175482] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.175482] system 00:04: [io  0x1854-0x1857] has been reserved
[    0.175482] system 00:04: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.176215] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.176216] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.176216] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.176217] system 00:05: [mem 0xf0000000-0xf7ffffff] has been reserved
[    0.176218] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.176218] system 00:05: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.176219] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.176220] system 00:05: [mem 0xff000000-0xffffffff] has been reserved
[    0.176220] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.176221] system 00:05: [mem 0xeffe0000-0xefffffff] has been reserved
[    0.176223] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.176251] system 00:06: [mem 0xfd000000-0xfdabffff] has been reserved
[    0.176252] system 00:06: [mem 0xfdad0000-0xfdadffff] has been reserved
[    0.176253] system 00:06: [mem 0xfdb00000-0xfdffffff] has been reserved
[    0.176253] system 00:06: [mem 0xfe000000-0xfe01ffff] could not be reserved
[    0.176254] system 00:06: [mem 0xfe036000-0xfe03bfff] has been reserved
[    0.176255] system 00:06: [mem 0xfe03d000-0xfe3fffff] has been reserved
[    0.176255] system 00:06: [mem 0xfe410000-0xfe7fffff] has been reserved
[    0.176257] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.176458] system 00:07: [io  0xff00-0xfffe] has been reserved
[    0.176460] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177273] system 00:08: [mem 0xfdaf0000-0xfdafffff] has been reserved
[    0.177274] system 00:08: [mem 0xfdae0000-0xfdaeffff] has been reserved
[    0.177275] system 00:08: [mem 0xfdac0000-0xfdacffff] has been reserved
[    0.177276] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177905] pnp: PnP ACPI: found 9 devices
[    0.183025] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.183056] NET: Registered protocol family 2
[    0.183138] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.183178] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.183267] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[    0.183303] TCP: Hash tables configured (established 131072 bind 65536)
[    0.183340] MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear)
[    0.183369] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.183391] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.183434] NET: Registered protocol family 1
[    0.183436] NET: Registered protocol family 44
[    0.183444] pci 0000:02:00.0: PCI bridge to [bus 03]
[    0.183445] pci 0000:02:00.0:   bridge window [io  0xe000-0xefff]
[    0.183448] pci 0000:02:00.0:   bridge window [mem 0xef700000-0xef9fffff]
[    0.183450] pci 0000:02:00.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183453] pci 0000:01:00.0: PCI bridge to [bus 02-03]
[    0.183454] pci 0000:01:00.0:   bridge window [io  0xe000-0xefff]
[    0.183457] pci 0000:01:00.0:   bridge window [mem 0xef700000-0xef9fffff]
[    0.183459] pci 0000:01:00.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183462] pci 0000:00:01.0: PCI bridge to [bus 01-03]
[    0.183463] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.183464] pci 0000:00:01.0:   bridge window [mem 0xef700000-0xefafffff]
[    0.183465] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183467] pci 0000:00:1b.0: PCI bridge to [bus 04]
[    0.183469] pci 0000:00:1b.0:   bridge window [mem 0xefd00000-0xefdfffff]
[    0.183473] pci 0000:00:1b.4: PCI bridge to [bus 05]
[    0.183478] pci 0000:00:1c.0: PCI bridge to [bus 06]
[    0.183480] pci 0000:00:1c.0:   bridge window [mem 0xefc00000-0xefcfffff]
[    0.183484] pci 0000:00:1c.5: PCI bridge to [bus 07]
[    0.183485] pci 0000:00:1c.5:   bridge window [io  0xd000-0xdfff]
[    0.183487] pci 0000:00:1c.5:   bridge window [mem 0xefb00000-0xefbfffff]
[    0.183491] pci 0000:00:1c.6: PCI bridge to [bus 08]
[    0.183496] pci 0000:00:1c.7: PCI bridge to [bus 09]
[    0.183501] pci 0000:00:1d.0: PCI bridge to [bus 0a]
[    0.183507] pci 0000:00:1d.5: PCI bridge to [bus 0b]
[    0.183509] pci 0000:00:1d.5:   bridge window [mem 0xef400000-0xef6fffff]
[    0.183513] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.183514] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.183514] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.183515] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xefffffff window]
[    0.183515] pci_bus 0000:00: resource 8 [mem 0xfd000000-0xfe7fffff window]
[    0.183516] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.183516] pci_bus 0000:01: resource 1 [mem 0xef700000-0xefafffff]
[    0.183517] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183517] pci_bus 0000:02: resource 0 [io  0xe000-0xefff]
[    0.183518] pci_bus 0000:02: resource 1 [mem 0xef700000-0xef9fffff]
[    0.183518] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183519] pci_bus 0000:03: resource 0 [io  0xe000-0xefff]
[    0.183519] pci_bus 0000:03: resource 1 [mem 0xef700000-0xef9fffff]
[    0.183520] pci_bus 0000:03: resource 2 [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183520] pci_bus 0000:04: resource 1 [mem 0xefd00000-0xefdfffff]
[    0.183521] pci_bus 0000:06: resource 1 [mem 0xefc00000-0xefcfffff]
[    0.183522] pci_bus 0000:07: resource 0 [io  0xd000-0xdfff]
[    0.183522] pci_bus 0000:07: resource 1 [mem 0xefb00000-0xefbfffff]
[    0.183523] pci_bus 0000:0b: resource 1 [mem 0xef400000-0xef6fffff]
[    0.208219] pci 0000:00:14.0: quirk_usb_early_handoff+0x0/0x6e0 took 24014 usecs
[    0.208252] pci 0000:03:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.208265] pci 0000:03:00.1: D0 power state depends on 0000:03:00.0
[    0.208475] pci 0000:06:00.0: PME# does not work under D0, disabling it
[    0.208696] PCI: CLS 64 bytes, default 64
[    0.208714] Trying to unpack rootfs image as initramfs...
[    0.290686] Freeing initrd memory: 13296K
[    0.290709] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.290710] software IO TLB: mapped [mem 0xaf2a2000-0xb32a2000] (64MB)
[    0.290827] check: Scanning for low memory corruption every 60 seconds
[    0.291010] Initialise system trusted keyrings
[    0.291016] Key type blacklist registered
[    0.291041] workingset: timestamp_bits=41 max_order=22 bucket_order=0
[    0.291611] zbud: loaded
[    0.296327] Key type asymmetric registered
[    0.296327] Asymmetric key parser 'x509' registered
[    0.296331] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.296351] io scheduler mq-deadline registered
[    0.296352] io scheduler kyber registered
[    0.296363] io scheduler bfq registered
[    0.297456] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.297496] efifb: probing for efifb
[    0.297505] efifb: framebuffer at 0xd0000000, using 3072k, total 3072k
[    0.297505] efifb: mode is 1024x768x32, linelength=4096, pages=1
[    0.297505] efifb: scrolling: redraw
[    0.297506] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.297523] fbcon: Deferring console take-over
[    0.297523] fb0: EFI VGA frame buffer device
[    0.297527] intel_idle: MWAIT substates: 0x142120
[    0.297527] intel_idle: v0.5.1 model 0x9E
[    0.297742] intel_idle: Local APIC timer is reliable in all C-states
[    0.297798] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[    0.297810] ACPI: Sleep Button [SLPB]
[    0.297825] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    0.297834] ACPI: Power Button [PWRB]
[    0.297848] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.299483] ACPI: Power Button [PWRF]
[    0.300118] thermal LNXTHERM:00: registered as thermal_zone0
[    0.300119] ACPI: Thermal Zone [TZ00] (28 C)
[    0.300221] thermal LNXTHERM:01: registered as thermal_zone1
[    0.300222] ACPI: Thermal Zone [TZ01] (30 C)
[    0.300401] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.300994] AMD-Vi: AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[    0.300995] AMD-Vi: AMD IOMMUv2 functionality not available on this system
[    0.301650] nvme nvme0: pci function 0000:04:00.0
[    0.301666] ahci 0000:00:17.0: version 3.0
[    0.301843] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 3 ports 6 Gbps 0xd impl SATA mode
[    0.301845] ahci 0000:00:17.0: flags: 64bit ncq sntf pm led clo only pio slum part ems deso sadm sds apst 
[    0.310148] nvme nvme0: missing or invalid SUBNQN field.
[    0.310158] nvme nvme0: Shutdown timeout set to 8 seconds
[    0.319828] scsi host0: ahci
[    0.320055] scsi host1: ahci
[    0.320239] scsi host2: ahci
[    0.320319] scsi host3: ahci
[    0.320337] ata1: SATA max UDMA/133 abar m2048@0xefe4b000 port 0xefe4b100 irq 132
[    0.320337] ata2: DUMMY
[    0.320338] ata3: SATA max UDMA/133 abar m2048@0xefe4b000 port 0xefe4b200 irq 132
[    0.320339] ata4: SATA max UDMA/133 abar m2048@0xefe4b000 port 0xefe4b280 irq 132
[    0.320364] usbcore: registered new interface driver usbserial_generic
[    0.320366] usbserial: USB Serial support registered for generic
[    0.320377] rtc_cmos 00:03: RTC can wake from S4
[    0.320823] rtc_cmos 00:03: registered as rtc0
[    0.320918] rtc_cmos 00:03: setting system clock to 2020-11-20T19:15:05 UTC (1605899705)
[    0.320926] rtc_cmos 00:03: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    0.320953] intel_pstate: Intel P-state driver initializing
[    0.321127] intel_pstate: Disabling energy efficiency optimization
[    0.321127] intel_pstate: HWP enabled
[    0.321187] ledtrig-cpu: registered to indicate activity on CPUs
[    0.321218] resource sanity check: requesting [mem 0xfdffe800-0xfe0007ff], which spans more than pnp 00:06 [mem 0xfdb00000-0xfdffffff]
[    0.321220] caller pmc_core_probe+0x85/0x380 mapping multiple BARs
[    0.321227] intel_pmc_core INT33A1:00:  initialized
[    0.321275] drop_monitor: Initializing network drop monitor service
[    0.321355] NET: Registered protocol family 10
[    0.321591] nvme nvme0: 8/0/0 default/read/poll queues
[    0.324664] Segment Routing with IPv6
[    0.324665] RPL Segment Routing with IPv6
[    0.324677] NET: Registered protocol family 17
[    0.325080] microcode: sig=0x906e9, pf=0x2, revision=0xde
[    0.325144] microcode: Microcode Update Driver: v2.2.
[    0.325146] IPI shorthand broadcast: enabled
[    0.325151] sched_clock: Marking stable (324767658, 373892)->(330539705, -5398155)
[    0.325240] registered taskstats version 1
[    0.325240]  nvme0n1: p1 p2 p3
[    0.325245] Loading compiled-in X.509 certificates
[    0.326984] Loaded X.509 cert 'Build time autogenerated kernel key: 00e32af39d4a2635c8d60f93bbd3e041fd36fd45'
[    0.327041] zswap: loaded using pool lz4/z3fold
[    0.327179] Key type ._fscrypt registered
[    0.327180] Key type .fscrypt registered
[    0.327180] Key type fscrypt-provisioning registered
[    0.328406] PM:   Magic number: 12:270:294
[    0.328411] ata_device dev2.0: hash matches
[    0.328412]  dev2.0: hash matches
[    0.328414] misc hpet: hash matches
[    0.328423] tty tty27: hash matches
[    0.328510] RAS: Correctable Errors collector initialized.
[    0.636150] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    0.636179] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    0.636204] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    0.636773] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT2._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.636809] fbcon: Taking over console
[    0.636819] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT2._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.636965] ata3.00: ATA-9: WDC WD3003FZEX-00Z4SA0, 01.01A01, max UDMA/133
[    0.636969] ata3.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    0.637045] Console: switching to colour frame buffer device 128x48
[    0.637514] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT2._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.637529] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT2._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.637654] ata3.00: configured for UDMA/133
[    0.638202] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT0._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.638223] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT0._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.638275] ata1.00: supports DRM functions and may not be fully accessible
[    0.638679] ata1.00: disabling queued TRIM support
[    0.638684] ata1.00: ATA-9: Samsung SSD 840 EVO 250GB, EXT0DB6Q, max UDMA/133
[    0.638688] ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 32), AA
[    0.639412] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT0._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.639431] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT0._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.639480] ata1.00: supports DRM functions and may not be fully accessible
[    0.639877] ata1.00: disabling queued TRIM support
[    0.640292] ata1.00: configured for UDMA/133
[    0.640553] scsi 0:0:0:0: Direct-Access     ATA      Samsung SSD 840  DB6Q PQ: 0 ANSI: 5
[    0.641033] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[    0.641054] sd 0:0:0:0: [sda] Write Protect is off
[    0.641058] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.641088] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.641241] scsi 2:0:0:0: Direct-Access     ATA      WDC WD3003FZEX-0 1A01 PQ: 0 ANSI: 5
[    0.641644] sd 2:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[    0.641649] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[    0.641666] sd 2:0:0:0: [sdb] Write Protect is off
[    0.641669] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    0.641695] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.644226]  sda: sda1 sda2 sda3 sda4
[    0.645996] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT3._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.646150] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT3._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.646186] sd 0:0:0:0: [sda] supports TCG Opal
[    0.646261] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.646603] ata4.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133
[    0.646608] ata4.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    0.656583] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT3._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.656708] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT3._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.657389] ata4.00: configured for UDMA/133
[    0.657621] scsi 3:0:0:0: Direct-Access     ATA      WDC WD30EZRX-00M 0A80 PQ: 0 ANSI: 5
[    0.658066] sd 3:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[    0.658070] sd 3:0:0:0: [sdc] 4096-byte physical blocks
[    0.658089] sd 3:0:0:0: [sdc] Write Protect is off
[    0.658093] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    0.658124] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.677878]  sdb: sdb1
[    0.678666] sd 2:0:0:0: [sdb] Attached SCSI disk
[    0.694784]  sdc: sdc1 sdc2
[    0.695808] sd 3:0:0:0: [sdc] Attached SCSI disk
[    0.699907] Freeing unused decrypted memory: 2040K
[    0.700712] Freeing unused kernel image (initmem) memory: 1660K
[    0.722822] Write protecting the kernel read-only data: 24576k
[    0.724266] Freeing unused kernel image (text/rodata gap) memory: 2044K
[    0.724630] Freeing unused kernel image (rodata/data gap) memory: 244K
[    0.798618] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.798619] x86/mm: Checking user space page tables
[    0.830223] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.830225] Run /init as init process
[    0.830226]   with arguments:
[    0.830226]     /init
[    0.830227]   with environment:
[    0.830227]     HOME=/
[    0.830227]     TERM=linux
[    0.953886] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.953891] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    0.954954] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810
[    0.954958] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    0.955095] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    0.955096] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.955097] usb usb1: Product: xHCI Host Controller
[    0.955097] usb usb1: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    0.955098] usb usb1: SerialNumber: 0000:00:14.0
[    0.955196] hub 1-0:1.0: USB hub found
[    0.955212] hub 1-0:1.0: 16 ports detected
[    0.956513] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.956515] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    0.956517] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[    0.956537] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[    0.956538] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.956538] usb usb2: Product: xHCI Host Controller
[    0.956539] usb usb2: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    0.956539] usb usb2: SerialNumber: 0000:00:14.0
[    0.956625] hub 2-0:1.0: USB hub found
[    0.956636] hub 2-0:1.0: 10 ports detected
[    0.957496] usb: port power management may be unreliable
[    0.957635] xhci_hcd 0000:03:00.2: xHCI Host Controller
[    0.957637] xhci_hcd 0000:03:00.2: new USB bus registered, assigned bus number 3
[    0.957708] xhci_hcd 0000:03:00.2: hcc params 0x0260ffe5 hci version 0x110 quirks 0x0000000000000010
[    0.957847] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    0.957847] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.957848] usb usb3: Product: xHCI Host Controller
[    0.957849] usb usb3: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    0.957849] usb usb3: SerialNumber: 0000:03:00.2
[    0.957893] hub 3-0:1.0: USB hub found
[    0.957898] hub 3-0:1.0: 2 ports detected
[    0.957959] xhci_hcd 0000:03:00.2: xHCI Host Controller
[    0.957960] xhci_hcd 0000:03:00.2: new USB bus registered, assigned bus number 4
[    0.957961] xhci_hcd 0000:03:00.2: Host supports USB 3.1 Enhanced SuperSpeed
[    0.957970] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    0.957980] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[    0.957980] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.957981] usb usb4: Product: xHCI Host Controller
[    0.957981] usb usb4: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    0.957981] usb usb4: SerialNumber: 0000:03:00.2
[    0.958024] hub 4-0:1.0: USB hub found
[    0.958027] hub 4-0:1.0: 1 port detected
[    0.958174] xhci_hcd 0000:06:00.0: xHCI Host Controller
[    0.958175] xhci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 5
[    0.973591] random: fast init done
[    1.012973] xhci_hcd 0000:06:00.0: hcc params 0x0200ef80 hci version 0x110 quirks 0x0000000000800010
[    1.013146] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    1.013146] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.013147] usb usb5: Product: xHCI Host Controller
[    1.013147] usb usb5: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    1.013148] usb usb5: SerialNumber: 0000:06:00.0
[    1.013231] hub 5-0:1.0: USB hub found
[    1.013235] hub 5-0:1.0: 2 ports detected
[    1.013311] xhci_hcd 0000:06:00.0: xHCI Host Controller
[    1.013312] xhci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 6
[    1.013314] xhci_hcd 0000:06:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[    1.013337] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.013347] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[    1.013348] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.013349] usb usb6: Product: xHCI Host Controller
[    1.013349] usb usb6: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    1.013349] usb usb6: SerialNumber: 0000:06:00.0
[    1.013399] hub 6-0:1.0: USB hub found
[    1.013403] hub 6-0:1.0: 2 ports detected
[    1.266147] usb 3-2: new full-speed USB device number 2 using xhci_hcd
[    1.266170] usb 1-11: new high-speed USB device number 2 using xhci_hcd
[    1.282816] tsc: Refined TSC clocksource calibration: 4199.998 MHz
[    1.282834] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x3c8a5f8911c, max_idle_ns: 440795307124 ns
[    1.282898] clocksource: Switched to clocksource tsc
[    1.407593] usb 1-11: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=32.98
[    1.407598] usb 1-11: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.407602] usb 1-11: Product: USB2.0 Hub
[    1.408675] hub 1-11:1.0: USB hub found
[    1.409013] hub 1-11:1.0: 4 ports detected
[    1.429102] usb 3-2: New USB device found, idVendor=2516, idProduct=014d, bcdDevice= 1.04
[    1.429108] usb 3-2: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[    1.429111] usb 3-2: Product: ARES
[    1.429114] usb 3-2: Manufacturer: Cooler Master Technology Inc.
[    1.451850] hid: raw HID events driver (C) Jiri Kosina
[    1.466084] usbcore: registered new interface driver usbhid
[    1.466085] usbhid: USB HID core driver
[    1.467049] input: Cooler Master Technology Inc. ARES as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.2/usb3/3-2/3-2:1.0/0003:2516:014D.0001/input/input3
[    1.468208] EXT4-fs (nvme0n1p3): mounted filesystem with ordered data mode. Opts: (null)
[    1.522815] hid-generic 0003:2516:014D.0001: input,hidraw0: USB HID v1.11 Keyboard [Cooler Master Technology Inc. ARES] on usb-0000:03:00.2-2/input0
[    1.522899] hid-generic 0003:2516:014D.0002: hiddev0,hidraw1: USB HID v1.11 Device [Cooler Master Technology Inc. ARES] on usb-0000:03:00.2-2/input1
[    1.522967] input: Cooler Master Technology Inc. ARES System Control as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.2/usb3/3-2/3-2:1.2/0003:2516:014D.0003/input/input4
[    1.529678] random: crng init done
[    1.529705] systemd[1]: Successfully credited entropy passed from boot loader.
[    1.531590] systemd[1]: systemd 246.6-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    1.532808] usb 1-12: new full-speed USB device number 3 using xhci_hcd
[    1.546198] systemd[1]: Detected architecture x86-64.
[    1.568432] systemd[1]: Set hostname to <handl3vogn>.
[    1.579540] input: Cooler Master Technology Inc. ARES Consumer Control as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.2/usb3/3-2/3-2:1.2/0003:2516:014D.0003/input/input5
[    1.579688] hid-generic 0003:2516:014D.0003: input,hidraw2: USB HID v1.11 Device [Cooler Master Technology Inc. ARES] on usb-0000:03:00.2-2/input2
[    1.675962] usb 1-12: New USB device found, idVendor=046d, idProduct=c066, bcdDevice=58.02
[    1.675966] usb 1-12: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.675968] usb 1-12: Product: G9x Laser Mouse
[    1.675970] usb 1-12: Manufacturer: Logitech
[    1.675972] usb 1-12: SerialNumber: B8CA32E9CE0018
[    1.679001] input: Logitech G9x Laser Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-12/1-12:1.0/0003:046D:C066.0004/input/input6
[    1.679089] hid-generic 0003:046D:C066.0004: input,hidraw3: USB HID v1.11 Mouse [Logitech G9x Laser Mouse] on usb-0000:00:14.0-12/input0
[    1.681686] input: Logitech G9x Laser Mouse Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-12/1-12:1.1/0003:046D:C066.0005/input/input7
[    1.728724] systemd[1]: Queued start job for default target Graphical Interface.
[    1.729484] systemd[1]: Created slice system-getty.slice.
[    1.729692] systemd[1]: Created slice system-modprobe.slice.
[    1.729870] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    1.730082] systemd[1]: Created slice User and Session Slice.
[    1.730167] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    1.730245] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    1.730394] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    1.730465] systemd[1]: Reached target Local Encrypted Volumes.
[    1.730521] systemd[1]: Reached target Remote File Systems.
[    1.730568] systemd[1]: Reached target Slices.
[    1.730661] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[    1.730758] systemd[1]: Listening on LVM2 metadata daemon socket.
[    1.730933] systemd[1]: Listening on LVM2 poll daemon socket.
[    1.731949] systemd[1]: Listening on Process Core Dump Socket.
[    1.732080] systemd[1]: Listening on Journal Audit Socket.
[    1.732176] systemd[1]: Listening on Journal Socket (/dev/log).
[    1.732279] systemd[1]: Listening on Journal Socket.
[    1.732381] systemd[1]: Listening on udev Control Socket.
[    1.732927] systemd[1]: Listening on udev Kernel Socket.
[    1.733904] systemd[1]: Mounting Huge Pages File System...
[    1.734861] systemd[1]: Mounting POSIX Message Queue File System...
[    1.735816] systemd[1]: Mounting Kernel Debug File System...
[    1.736112] input: Logitech G9x Laser Mouse Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-12/1-12:1.1/0003:046D:C066.0005/input/input8
[    1.736246] hid-generic 0003:046D:C066.0005: input,hiddev1,hidraw4: USB HID v1.11 Keyboard [Logitech G9x Laser Mouse] on usb-0000:00:14.0-12/input1
[    1.736783] systemd[1]: Mounting Kernel Trace File System...
[    1.737648] systemd[1]: Starting Create list of static device nodes for the current kernel...
[    1.738507] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[    1.739344] systemd[1]: Starting Load Kernel Module drm...
[    1.740343] systemd[1]: Starting Set Up Additional Binary Formats...
[    1.740750] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    1.741539] systemd[1]: Starting Journal Service...
[    1.742722] systemd[1]: Starting Load Kernel Modules...
[    1.743830] systemd[1]: Starting Remount Root and Kernel File Systems...
[    1.743906] Linux agpgart interface v0.103
[    1.744559] systemd[1]: Condition check resulted in Repartition Root Disk being skipped.
[    1.745181] systemd[1]: Starting Coldplug All udev Devices...
[    1.746067] usb 1-11.2: new full-speed USB device number 4 using xhci_hcd
[    1.746786] systemd[1]: Mounted Huge Pages File System.
[    1.747341] systemd[1]: Mounted POSIX Message Queue File System.
[    1.747744] systemd[1]: Mounted Kernel Debug File System.
[    1.747875] EXT4-fs (nvme0n1p3): re-mounted. Opts: (null)
[    1.748610] systemd[1]: Mounted Kernel Trace File System.
[    1.749344] systemd[1]: Finished Create list of static device nodes for the current kernel.
[    1.749980] systemd[1]: Finished Remount Root and Kernel File Systems.
[    1.750554] systemd[1]: proc-sys-fs-binfmt_misc.automount: Got automount request for /proc/sys/fs/binfmt_misc, triggered by 256 (systemd-binfmt)
[    1.751261] systemd[1]: Mounting Arbitrary Executable File Formats File System...
[    1.751793] systemd[1]: Condition check resulted in First Boot Wizard being skipped.
[    1.752035] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[    1.752574] systemd[1]: Starting Load/Save Random Seed...
[    1.752667] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.752691] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    1.752712] sd 3:0:0:0: Attached scsi generic sg2 type 0
[    1.752986] systemd[1]: Condition check resulted in Create System Users being skipped.
[    1.753442] systemd[1]: Starting Create Static Device Nodes in /dev...
[    1.754346] systemd[1]: Mounted Arbitrary Executable File Formats File System.
[    1.755824] systemd[1]: Finished Set Up Additional Binary Formats.
[    1.763033] systemd[1]: modprobe@drm.service: Succeeded.
[    1.763313] systemd[1]: Finished Load Kernel Module drm.
[    1.769297] systemd[1]: Finished Create Static Device Nodes in /dev.
[    1.771016] systemd[1]: Starting Rule-based Manager for Device Events and Files...
[    1.772027] systemd[1]: Finished Load/Save Random Seed.
[    1.773058] vboxdrv: loading out-of-tree module taints kernel.
[    1.773159] vboxdrv: module verification failed: signature and/or required key missing - tainting kernel
[    1.775402] vboxdrv: Found 8 processor cores
[    1.796233] vboxdrv: TSC mode is Invariant, tentative frequency 4199997168 Hz
[    1.796234] vboxdrv: Successfully loaded version 6.1.16 (interface 0x00300000)
[    1.796776] VBoxNetAdp: Successfully started.
[    1.797871] VBoxNetFlt: Successfully started.
[    1.798522] systemd[1]: Finished Coldplug All udev Devices.
[    1.800107] systemd[1]: Finished Load Kernel Modules.
[    1.800498] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[    1.800915] systemd[1]: Mounting Kernel Configuration File System...
[    1.801580] systemd[1]: Starting Apply Kernel Variables...
[    1.802223] systemd[1]: Mounted Kernel Configuration File System.
[    1.805693] systemd[1]: Finished Apply Kernel Variables.
[    1.841894] usb 1-11.2: New USB device found, idVendor=0665, idProduct=6000, bcdDevice= 0.97
[    1.841895] usb 1-11.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.841896] usb 1-11.2: Product: Gaming keyboard
[    1.841897] usb 1-11.2: Manufacturer: EST
[    1.849717] input: EST Gaming keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11.2/1-11.2:1.0/0003:0665:6000.0006/input/input11
[    1.906179] hid-generic 0003:0665:6000.0006: input,hidraw5: USB HID v1.11 Keyboard [EST Gaming keyboard] on usb-0000:00:14.0-11.2/input0
[    1.906766] input: EST Gaming keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11.2/1-11.2:1.1/0003:0665:6000.0007/input/input12
[    1.957288] systemd[1]: Started Journal Service.
[    1.957917] audit: type=1130 audit(1605899707.131:2): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journald comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    1.962836] hid-generic 0003:0665:6000.0007: input,hidraw6: USB HID v1.11 Device [EST Gaming keyboard] on usb-0000:00:14.0-11.2/input1
[    1.963330] input: EST Gaming keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11.2/1-11.2:1.2/0003:0665:6000.0008/input/input13
[    1.991912] audit: type=1130 audit(1605899707.165:3): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udevd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    1.993006] audit: type=1130 audit(1605899707.168:4): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=lvm2-lvmetad comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.019580] hid-generic 0003:0665:6000.0008: input,hidraw7: USB HID v1.11 Keyboard [EST Gaming keyboard] on usb-0000:00:14.0-11.2/input2
[    2.050667] wmi_bus wmi_bus-PNP0C14:01: WQAA data block query control method not found
[    2.102826] audit: type=1130 audit(1605899707.278:5): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journal-flush comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.114406] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[    2.149405] Adding 7863292k swap on /dev/nvme0n1p2.  Priority:-2 extents:1 across:7863292k SSFS
[    2.190385] mousedev: PS/2 mouse device common for all mice
[    2.229669] bcma-pci-bridge 0000:0b:00.0: enabling device (0000 -> 0002)
[    2.229764] bcma-pci-bridge 0000:0b:00.0: bus0: Found chip with id 0x4360, rev 0x03 and package 0x01
[    2.229787] bcma-pci-bridge 0000:0b:00.0: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0)
[    2.229800] bcma-pci-bridge 0000:0b:00.0: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0)
[    2.229824] bcma-pci-bridge 0000:0b:00.0: bus0: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0)
[    2.229849] bcma-pci-bridge 0000:0b:00.0: bus0: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0)
[    2.229861] bcma-pci-bridge 0000:0b:00.0: bus0: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0)
[    2.261646] bcma: Unsupported SPROM revision: 11
[    2.262186] bcma-pci-bridge 0000:0b:00.0: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[    2.262187] bcma-pci-bridge 0000:0b:00.0: bus0: Using fallback SPROM failed (err -2)
[    2.262188] bcma-pci-bridge 0000:0b:00.0: bus0: No SPROM available
[    2.265374] bcma-pci-bridge 0000:0b:00.0: bus0: Bus registered
[    2.270087] e1000e: Intel(R) PRO/1000 Network Driver
[    2.270087] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.270237] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    2.270688] i801_smbus 0000:00:1f.4: enabling device (0001 -> 0003)
[    2.270724] input: PC Speaker as /devices/platform/pcspkr/input/input14
[    2.270805] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[    2.270836] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[    2.276828] i2c i2c-0: 2/4 memory slots populated (from DMI)
[    2.277333] i2c i2c-0: Successfully instantiated SPD at 0x51
[    2.278885] i2c i2c-0: Successfully instantiated SPD at 0x53
[    2.281069] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 655360 ms ovfl timer
[    2.281070] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[    2.281070] RAPL PMU: hw unit of domain package 2^-14 Joules
[    2.281071] RAPL PMU: hw unit of domain dram 2^-14 Joules
[    2.281209] alx 0000:07:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [1c:1b:0d:93:d6:12]
[    2.283380] audit: type=1130 audit(1605899707.458:6): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=lvm2-monitor comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.284870] cryptd: max_cpu_qlen set to 1000
[    2.306025] audit: type=1130 audit(1605899707.478:7): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-fsck@dev-disk-by\x2duuid-1669\x2dA524 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.319353] AVX2 version of gcm_enc/dec engaged.
[    2.319354] AES CTR mode by8 optimization enabled
[    2.463103] alx 0000:07:00.0 enp7s0: renamed from eth0
[    2.503803] iTCO_vendor_support: vendor-support=0
[    2.505790] ee1004 0-0051: 512 byte EE1004-compliant SPD EEPROM, read-only
[    2.507389] ee1004 0-0053: 512 byte EE1004-compliant SPD EEPROM, read-only
[    2.515766] snd_hda_intel 0000:03:00.1: Force to non-snoop mode
[    2.534187] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
[    2.564345] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[    2.564434] iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400)
[    2.569371] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    2.595383] audit: type=1130 audit(1605899707.768:8): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.605252] audit: type=1127 audit(1605899707.778:9): pid=454 uid=0 auid=4294967295 ses=4294967295 msg=' comm="systemd-update-utmp" exe="/usr/lib/systemd/systemd-update-utmp" hostname=? addr=? terminal=? res=success'
[    2.610480] audit: type=1130 audit(1605899707.785:10): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-update-utmp comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.624157] e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) 1c:1b:0d:93:d6:10
[    2.624162] e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
[    2.624240] e1000e 0000:00:1f.6 eth0: MAC: 12, PHY: 12, PBA No: FFFFFF-0FF
[    2.656558] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input15
[    2.656588] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input16
[    2.656615] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input17
[    2.656641] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input18
[    2.656663] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input19
[    2.656686] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input20
[    2.657987] e1000e 0000:00:1f.6 enp0s31f6: renamed from eth0
[    2.693316] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC1220: line_outs=3 (0x14/0x15/0x16/0x0/0x0) type:line
[    2.693318] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    2.693319] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[    2.693320] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[    2.693321] snd_hda_codec_realtek hdaudioC0D0:    dig-out=0x1e/0x0
[    2.693322] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[    2.693323] snd_hda_codec_realtek hdaudioC0D0:      Front Mic=0x19
[    2.693324] snd_hda_codec_realtek hdaudioC0D0:      Rear Mic=0x18
[    2.693325] snd_hda_codec_realtek hdaudioC0D0:      Line=0x1a
[    2.706719] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input21
[    2.706760] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input22
[    2.706798] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1f.3/sound/card0/input23
[    2.706832] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24
[    2.706865] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1f.3/sound/card0/input25
[    2.706896] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1f.3/sound/card0/input26
[    2.706929] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input27
[    2.825980] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.826460] intel_rapl_common: Found RAPL domain package
[    2.826461] intel_rapl_common: Found RAPL domain core
[    2.826462] intel_rapl_common: Found RAPL domain dram
[    2.827879] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.828034] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.828035] cfg80211: failed to load regulatory.db
[    2.894601] [drm] amdgpu kernel modesetting enabled.
[    2.894713] CRAT table not found
[    2.894719] Virtual CRAT table created for CPU
[    2.894729] amdgpu: Topology: Add CPU node
[    2.894794] checking generic (d0000000 300000) vs hw (d0000000 10000000)
[    2.894795] fb0: switching to amdgpudrmfb from EFI VGA
[    2.894841] Console: switching to colour dummy device 80x25
[    2.895353] amdgpu 0000:03:00.0: vgaarb: deactivate vga console
[    2.895456] [drm] initializing kernel modesetting (SIENNA_CICHLID 0x1002:0x73BF 0x1002:0x0E3A 0xC1).
[    2.895458] amdgpu 0000:03:00.0: amdgpu: Trusted Memory Zone (TMZ) feature not supported
[    2.895464] [drm] register mmio base: 0xEF800000
[    2.895464] [drm] register mmio size: 1048576
[    2.896529] [drm] add ip block number 0 <nv_common>
[    2.896530] [drm] add ip block number 1 <gmc_v10_0>
[    2.896530] [drm] add ip block number 2 <navi10_ih>
[    2.896531] [drm] add ip block number 3 <psp>
[    2.896531] [drm] add ip block number 4 <smu>
[    2.896532] [drm] add ip block number 5 <dm>
[    2.896532] [drm] add ip block number 6 <gfx_v10_0>
[    2.896533] [drm] add ip block number 7 <sdma_v5_2>
[    2.896535] [drm] add ip block number 8 <vcn_v3_0>
[    2.896535] [drm] add ip block number 9 <jpeg_v3_0>
[    2.896547] amdgpu 0000:03:00.0: No more image in the PCI ROM
[    2.896557] amdgpu: ATOM BIOS: 113-D4120500-101
[    2.896564] [drm] VCN(0) decode is enabled in VM mode
[    2.896565] [drm] VCN(1) decode is enabled in VM mode
[    2.896565] [drm] VCN(0) encode is enabled in VM mode
[    2.896565] [drm] VCN(1) encode is enabled in VM mode
[    2.896567] [drm] JPEG decode is enabled in VM mode
[    2.896583] [drm] vm size is 262144 GB, 4 levels, block size is 9-bit, fragment size is 9-bit
[    2.896588] amdgpu 0000:03:00.0: amdgpu: VRAM: 16368M 0x0000008000000000 - 0x00000083FEFFFFFF (16368M used)
[    2.896589] amdgpu 0000:03:00.0: amdgpu: GART: 512M 0x0000000000000000 - 0x000000001FFFFFFF
[    2.896596] [drm] Detected VRAM RAM=16368M, BAR=256M
[    2.896596] [drm] RAM width 256bits GDDR6
[    2.896630] [TTM] Zone  kernel: Available graphics memory: 8170886 KiB
[    2.896630] [TTM] Zone   dma32: Available graphics memory: 2097152 KiB
[    2.896631] [TTM] Initializing pool allocator
[    2.896633] [TTM] Initializing DMA pool allocator
[    2.896660] [drm] amdgpu: 16368M of VRAM memory ready
[    2.896662] [drm] amdgpu: 11969M of GTT memory ready.
[    2.896663] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    2.896745] [drm] PCIE GART of 512M enabled (table at 0x0000008000300000).
[    2.897067] amdgpu 0000:03:00.0: Direct firmware load for amdgpu/sienna_cichlid_sos.bin failed with error -2
[    2.897069] amdgpu 0000:03:00.0: amdgpu: failed to init sos firmware
[    2.897140] [drm:psp_sw_init [amdgpu]] *ERROR* Failed to load psp firmware!
[    2.897203] [drm:amdgpu_device_init.cold [amdgpu]] *ERROR* sw_init of IP block <psp> failed -2
[    2.897206] amdgpu 0000:03:00.0: amdgpu: amdgpu_device_ip_init failed
[    2.897209] amdgpu 0000:03:00.0: amdgpu: Fatal error during GPU init
[    2.897211] [drm] amdgpu: finishing device.
[    2.897364] ------------[ cut here ]------------
[    2.897365] Memory manager not clean during takedown.
[    2.897396] WARNING: CPU: 5 PID: 281 at drivers/gpu/drm/drm_mm.c:998 drm_mm_takedown+0x1f/0x30 [drm]
[    2.897397] Modules linked in: fjes(-) acpi_cpufreq(-) amdgpu(+) intel_rapl_msr intel_rapl_common cfg80211 ssb x86_pkg_temp_thermal mmc_core intel_powerclamp coretemp kvm_intel snd_hda_codec_realtek rfkill snd_hda_codec_generic kvm ledtrig_audio gpu_sched pcmcia snd_hda_codec_hdmi iTCO_wdt i2c_algo_bit nls_iso8859_1 pcmcia_core intel_pmc_bxt libarc4 snd_hda_intel nls_cp437 irqbypass ee1004 iTCO_vendor_support rng_core mei_hdcp intel_wmi_thunderbolt mxm_wmi ttm snd_intel_dspcfg crct10dif_pclmul vfat crc32_pclmul ghash_clmulni_intel fat snd_hda_codec drm_kms_helper aesni_intel crypto_simd snd_hda_core cryptd glue_helper cec snd_hwdep rapl snd_pcm rc_core intel_cstate syscopyarea i2c_i801 snd_timer sysfillrect intel_uncore alx pcspkr sysimgblt e1000e input_leds bcma i2c_smbus mousedev snd mei_me mdio fb_sys_fops soundcore mei wmi evdev joydev mac_hid uinput vboxnetflt(OE) vboxnetadp(OE) vboxdrv(OE) drm msr sg crypto_user agpgart ip_tables x_tables hid_generic ext4 usbhid crc32c_generic crc16
[    2.897417]  mbcache hid jbd2 crc32c_intel xhci_pci xhci_pci_renesas xhci_hcd
[    2.897420] CPU: 5 PID: 281 Comm: systemd-udevd Tainted: G           OE     5.9.9-arch1-1 #1
[    2.897421] Hardware name: Gigabyte Technology Co., Ltd. Z270X-Gaming 5/Z270X-Gaming 5, BIOS F10b 03/09/2018
[    2.897431] RIP: 0010:drm_mm_takedown+0x1f/0x30 [drm]
[    2.897432] Code: 0f 1f 84 00 00 00 00 00 0f 1f 00 0f 1f 44 00 00 48 8b 47 38 48 83 c7 38 48 39 f8 75 01 c3 48 c7 c7 c0 ba 5f c0 e8 ce bf 61 d1 <0f> 0b c3 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 0f 1f 44 00 00
[    2.897433] RSP: 0018:ffffa36a4066b9d0 EFLAGS: 00010286
[    2.897434] RAX: 0000000000000000 RBX: ffff89aa9abc50e0 RCX: 0000000000000000
[    2.897435] RDX: 0000000000000002 RSI: ffffffff9255986f RDI: 00000000ffffffff
[    2.897436] RBP: ffff89aaaac1d400 R08: 0000000000000469 R09: 0000000000000004
[    2.897436] R10: 0000000000000000 R11: 0000000000000001 R12: ffff89aaaac1d4f0
[    2.897437] R13: ffff89aa9abc4f68 R14: 0000000000000000 R15: 0000000000000000
[    2.897438] FS:  00007f3b08c6e440(0000) GS:ffff89aaaed40000(0000) knlGS:0000000000000000
[    2.897438] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    2.897439] CR2: 00007f9204abc024 CR3: 000000042a530001 CR4: 00000000003706e0
[    2.897440] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[    2.897440] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[    2.897441] Call Trace:
[    2.897503]  amdgpu_vram_mgr_fini+0x2c/0x60 [amdgpu]
[    2.897508]  ttm_bo_clean_mm+0xb3/0xd0 [ttm]
[    2.897563]  amdgpu_ttm_fini+0x8b/0xe0 [amdgpu]
[    2.897614]  amdgpu_bo_fini+0xe/0x30 [amdgpu]
[    2.897662]  gmc_v10_0_sw_fini+0x2e/0x40 [amdgpu]
[    2.897724]  amdgpu_device_fini+0x282/0x482 [amdgpu]
[    2.897767]  amdgpu_driver_unload_kms+0x3e/0x70 [amdgpu]
[    2.897828]  amdgpu_driver_load_kms.cold+0x35/0x57 [amdgpu]
[    2.897872]  amdgpu_pci_probe+0xf4/0x180 [amdgpu]
[    2.897875]  local_pci_probe+0x42/0x80
[    2.897877]  ? pci_match_device+0xd7/0x100
[    2.897878]  pci_device_probe+0xfa/0x1b0
[    2.897881]  really_probe+0x205/0x460
[    2.897883]  driver_probe_device+0xe1/0x150
[    2.897884]  device_driver_attach+0xa1/0xb0
[    2.897886]  __driver_attach+0x8a/0x150
[    2.897887]  ? device_driver_attach+0xb0/0xb0
[    2.897888]  ? device_driver_attach+0xb0/0xb0
[    2.897889]  bus_for_each_dev+0x89/0xd0
[    2.897891]  bus_add_driver+0x12b/0x1e0
[    2.897892]  driver_register+0x8b/0xe0
[    2.897894]  ? 0xffffffffc0ecd000
[    2.897895]  do_one_initcall+0x59/0x240
[    2.897898]  do_init_module+0x5c/0x260
[    2.897900]  load_module+0x21a7/0x2450
[    2.897903]  __do_sys_init_module+0x12d/0x180
[    2.897907]  do_syscall_64+0x33/0x40
[    2.897908]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[    2.897909] RIP: 0033:0x7f3b09a21e4e
[    2.897910] Code: 48 8b 0d 25 10 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 49 89 ca b8 af 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d f2 0f 0c 00 f7 d8 64 89 01 48
[    2.897911] RSP: 002b:00007ffcd19bb198 EFLAGS: 00000246 ORIG_RAX: 00000000000000af
[    2.897912] RAX: ffffffffffffffda RBX: 0000562b6cc98f20 RCX: 00007f3b09a21e4e
[    2.897913] RDX: 00007f3b09b5995d RSI: 0000000000afd3b9 RDI: 0000562b6dca7b20
[    2.897914] RBP: 0000562b6dca7b20 R08: 0000562b6dca7b20 R09: 00007ffcd19ba3f9
[    2.897914] R10: 0000562b6cb2f010 R11: 0000000000000246 R12: 00007f3b09b5995d
[    2.897915] R13: 0000000000000001 R14: 0000562b6cb33690 R15: 0000562b6cc98f20
[    2.897917] ---[ end trace a31d0dbcd2de0605 ]---
[    2.897927] [TTM] Finalizing pool allocator
[    2.897930] [TTM] Finalizing DMA pool allocator
[    2.897949] [TTM] Zone  kernel: Used memory at exit: 21 KiB
[    2.897951] [TTM] Zone   dma32: Used memory at exit: 0 KiB
[    2.897952] [drm] amdgpu: ttm finalized
[    2.898038] amdgpu: probe of 0000:03:00.0 failed with error -2
[    2.991304] b43-phy0: Broadcom 4360 WLAN found (core revision 42)
[    2.991639] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1)
[    2.991646] b43: probe of bcma0:1 failed with error -95
[    2.991658] Broadcom 43xx driver loaded [ Features: PNLS ]
[    7.851684] process '/usr/bin/xow' started with executable stack
[    8.070415] e1000e 0000:00:1f.6 enp0s31f6: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[    8.070489] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s31f6: link becomes ready

Can anyone give me a guide to how to get Sienna Cichlid firmware into my arch kernel?

Last edited by Handl3vogn (2020-11-20 19:27:00)

Offline

#4 2020-11-20 19:01:58

loqs
Member
Registered: 2014-03-06
Posts: 12,134

Re: Radeon 6800 / 6800XT graphics

Handl3vogn wrote:

Can anyone give me a guide to how to get Sienna Cichlid firmware into my arch kernel?

https://aur.archlinux.org/packages/linux-firmware-git/
Please use code tags for commands and their outputs.  Please also post complete outputs.

Offline

#5 2020-11-20 19:33:33

Handl3vogn
Member
Registered: 2020-11-20
Posts: 8

Re: Radeon 6800 / 6800XT graphics

Installing linux-firmware-git got me to boot to ttl but when trying to start GDM I now get a black screen

[    0.020604] PM: hibernation: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[    0.020605] PM: hibernation: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.020606] [mem 0xc0000000-0xefffffff] available for PCI devices
[    0.020606] Booting paravirtualized kernel on bare hardware
[    0.020608] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[    0.023480] setup_percpu: NR_CPUS:320 nr_cpumask_bits:320 nr_cpu_ids:8 nr_node_ids:1
[    0.023573] percpu: Embedded 56 pages/cpu s192512 r8192 d28672 u262144
[    0.023576] pcpu-alloc: s192512 r8192 d28672 u262144 alloc=1*2097152
[    0.023576] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.023587] Built 1 zonelists, mobility grouping on.  Total pages: 4116093
[    0.023587] Policy zone: Normal
[    0.023588] Kernel command line: initrd=\intel-ucode.img initrd=\initramfs-linux.img root=PARTUUID=dce06098-b799-4d70-b732-c8acb22e06d7 rw
[    0.024033] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear)
[    0.024245] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.024289] mem auto-init: stack:byref_all(zero), heap alloc:on, heap free:off
[    0.045369] Memory: 16149968K/16725820K available (14339K kernel code, 1505K rwdata, 7948K rodata, 1660K init, 2944K bss, 575592K reserved, 0K cma-reserved)
[    0.045374] random: get_random_u64 called from __kmem_cache_create+0x26/0x520 with crng_init=0
[    0.045445] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.045452] Kernel/User page tables isolation: enabled
[    0.045463] ftrace: allocating 40882 entries in 160 pages
[    0.053673] ftrace: allocated 160 pages with 2 groups
[    0.053732] rcu: Preemptible hierarchical RCU implementation.
[    0.053733] rcu: 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.053733] rcu: 	RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=8.
[    0.053734] rcu: 	RCU priority boosting: priority 1 delay 500 ms.
[    0.053734] 	Trampoline variant of Tasks RCU enabled.
[    0.053734] 	Rude variant of Tasks RCU enabled.
[    0.053735] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.053735] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.055350] NR_IRQS: 20736, nr_irqs: 2048, preallocated irqs: 16
[    0.055723] Console: colour dummy device 80x25
[    0.055726] printk: console [tty0] enabled
[    0.055735] ACPI: Core revision 20200717
[    0.055939] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635855245 ns
[    0.056001] APIC: Switch to symmetric I/O mode setup
[    0.056002] DMAR: Host address width 39
[    0.056003] DMAR: DRHD base: 0x000000fed90000 flags: 0x1
[    0.056006] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap d2008c40660462 ecap f050da
[    0.056006] DMAR: RMRR base: 0x000000bdf93000 end: 0x000000bdfb2fff
[    0.056007] DMAR-IR: IOAPIC id 2 under DRHD base  0xfed90000 IOMMU 0
[    0.056008] DMAR-IR: HPET id 0 under DRHD base 0xfed90000
[    0.056008] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
[    0.057296] DMAR-IR: Enabled IRQ remapping in x2apic mode
[    0.057297] x2apic enabled
[    0.057308] Switched APIC routing to cluster x2apic.
[    0.061362] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.075976] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x3c8a615336c, max_idle_ns: 440795257976 ns
[    0.075978] Calibrating delay loop (skipped), value calculated using timer frequency.. 8403.00 BogoMIPS (lpj=14000000)
[    0.075979] pid_max: default: 32768 minimum: 301
[    0.079256] LSM: Security Framework initializing
[    0.079259] Yama: becoming mindful.
[    0.079283] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.079297] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.079455] mce: CPU0: Thermal monitoring enabled (TM1)
[    0.079467] process: using mwait in idle threads
[    0.079468] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
[    0.079468] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[    0.079470] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.079470] Spectre V2 : Mitigation: Full generic retpoline
[    0.079471] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.079471] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.079472] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.079472] Spectre V2 : User space: Mitigation: STIBP via seccomp and prctl
[    0.079472] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[    0.079474] TAA: Mitigation: Clear CPU buffers
[    0.079475] SRBDS: Mitigation: Microcode
[    0.079476] MDS: Mitigation: Clear CPU buffers
[    0.079624] Freeing SMP alternatives memory: 32K
[    0.080314] smpboot: CPU0: Intel(R) Core(TM) i7-7700K CPU @ 4.20GHz (family: 0x6, model: 0x9e, stepping: 0x9)
[    0.080364] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver.
[    0.080369] ... version:                4
[    0.080369] ... bit width:              48
[    0.080370] ... generic registers:      4
[    0.080370] ... value mask:             0000ffffffffffff
[    0.080370] ... max period:             00007fffffffffff
[    0.080370] ... fixed-purpose events:   3
[    0.080371] ... event mask:             000000070000000f
[    0.080394] rcu: Hierarchical SRCU implementation.
[    0.080728] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.080770] smp: Bringing up secondary CPUs ...
[    0.080824] x86: Booting SMP configuration:
[    0.080825] .... node  #0, CPUs:      #1 #2 #3 #4
[    0.083949] MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details.
[    0.083949] TAA CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/tsx_async_abort.html for more details.
[    0.083949]  #5 #6 #7
[    0.083949] smp: Brought up 1 node, 8 CPUs
[    0.083949] smpboot: Max logical packages: 1
[    0.083949] smpboot: Total of 8 processors activated (67226.00 BogoMIPS)
[    0.086213] devtmpfs: initialized
[    0.086213] x86/mm: Memory block size: 128MB
[    0.086580] PM: Registering ACPI NVS region [mem 0xb4ade000-0xb4adefff] (4096 bytes)
[    0.086580] PM: Registering ACPI NVS region [mem 0xbe1ae000-0xbe85ffff] (7020544 bytes)
[    0.086580] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.086580] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.086580] pinctrl core: initialized pinctrl subsystem
[    0.086580] PM: RTC time: 19:31:11, date: 2020-11-20
[    0.086580] NET: Registered protocol family 16
[    0.086580] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    0.086580] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.086580] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.086580] audit: initializing netlink subsys (disabled)
[    0.086580] audit: type=2000 audit(1605900671.029:1): state=initialized audit_enabled=0 res=1
[    0.086580] thermal_sys: Registered thermal governor 'fair_share'
[    0.086580] thermal_sys: Registered thermal governor 'bang_bang'
[    0.086580] thermal_sys: Registered thermal governor 'step_wise'
[    0.086580] thermal_sys: Registered thermal governor 'user_space'
[    0.086580] thermal_sys: Registered thermal governor 'power_allocator'
[    0.086580] cpuidle: using governor ladder
[    0.086580] cpuidle: using governor menu
[    0.086580] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.086580] ACPI: bus type PCI registered
[    0.086580] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.086580] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[    0.086580] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[    0.086580] PCI: Using configuration type 1 for base access
[    0.086890] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.086890] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.086890] ACPI: Added _OSI(Module Device)
[    0.086890] ACPI: Added _OSI(Processor Device)
[    0.086890] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.086890] ACPI: Added _OSI(Processor Aggregator Device)
[    0.086890] ACPI: Added _OSI(Linux-Dell-Video)
[    0.086890] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.086890] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.114194] ACPI: 9 ACPI AML tables successfully acquired and loaded
[    0.116198] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.119311] ACPI: Dynamic OEM Table Load:
[    0.119311] ACPI: SSDT 0xFFFF905D6C4A3000 00081F (v02 PmRef  Cpu0Ist  00003000 INTL 20160422)
[    0.120158] ACPI: \_PR_.CPU0: _OSC native thermal LVT Acked
[    0.121283] ACPI: Dynamic OEM Table Load:
[    0.121285] ACPI: SSDT 0xFFFF905D6C451800 00065C (v02 PmRef  ApIst    00003000 INTL 20160422)
[    0.124998] ACPI: Interpreter enabled
[    0.125022] ACPI: (supports S0 S3 S4 S5)
[    0.125023] ACPI: Using IOAPIC for interrupt routing
[    0.125980] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.125980] ACPI: Enabled 8 GPEs in block 00 to 7F
[    0.127544] ACPI: Power Resource [PG00] (on)
[    0.127851] ACPI: Power Resource [PG01] (on)
[    0.128151] ACPI: Power Resource [PG02] (on)
[    0.129551] ACPI: Power Resource [WRST] (on)
[    0.129793] ACPI: Power Resource [WRST] (on)
[    0.130035] ACPI: Power Resource [WRST] (on)
[    0.130275] ACPI: Power Resource [WRST] (on)
[    0.130517] ACPI: Power Resource [WRST] (on)
[    0.130759] ACPI: Power Resource [WRST] (on)
[    0.131092] ACPI: Power Resource [WRST] (on)
[    0.131329] ACPI: Power Resource [WRST] (on)
[    0.131569] ACPI: Power Resource [WRST] (on)
[    0.131809] ACPI: Power Resource [WRST] (on)
[    0.132050] ACPI: Power Resource [WRST] (on)
[    0.132304] ACPI: Power Resource [WRST] (on)
[    0.132542] ACPI: Power Resource [WRST] (on)
[    0.132846] ACPI: Power Resource [WRST] (on)
[    0.133092] ACPI: Power Resource [WRST] (on)
[    0.133332] ACPI: Power Resource [WRST] (on)
[    0.133570] ACPI: Power Resource [WRST] (on)
[    0.134479] ACPI: Power Resource [WRST] (on)
[    0.134718] ACPI: Power Resource [WRST] (on)
[    0.134955] ACPI: Power Resource [WRST] (on)
[    0.144665] ACPI: Power Resource [FN00] (off)
[    0.144726] ACPI: Power Resource [FN01] (off)
[    0.144787] ACPI: Power Resource [FN02] (off)
[    0.144846] ACPI: Power Resource [FN03] (off)
[    0.144906] ACPI: Power Resource [FN04] (off)
[    0.145773] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])
[    0.145777] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3]
[    0.145804] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.146366] PCI host bridge to bus 0000:00
[    0.146367] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.146368] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.146368] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.146369] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xefffffff window]
[    0.146369] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfe7fffff window]
[    0.146370] pci_bus 0000:00: root bus resource [bus 00-7e]
[    0.146379] pci 0000:00:00.0: [8086:591f] type 00 class 0x060000
[    0.146627] pci 0000:00:01.0: [8086:1901] type 01 class 0x060400
[    0.146655] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.146872] pci 0000:00:08.0: [8086:1911] type 00 class 0x088000
[    0.146878] pci 0000:00:08.0: reg 0x10: [mem 0xefe4e000-0xefe4efff 64bit]
[    0.147000] pci 0000:00:14.0: [8086:a2af] type 00 class 0x0c0330
[    0.147013] pci 0000:00:14.0: reg 0x10: [mem 0xefe30000-0xefe3ffff 64bit]
[    0.147063] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.147303] pci 0000:00:16.0: [8086:a2ba] type 00 class 0x078000
[    0.147319] pci 0000:00:16.0: reg 0x10: [mem 0xefe4d000-0xefe4dfff 64bit]
[    0.147365] pci 0000:00:16.0: PME# supported from D3hot
[    0.147521] pci 0000:00:17.0: [8086:a282] type 00 class 0x010601
[    0.147530] pci 0000:00:17.0: reg 0x10: [mem 0xefe48000-0xefe49fff]
[    0.147535] pci 0000:00:17.0: reg 0x14: [mem 0xefe4c000-0xefe4c0ff]
[    0.147540] pci 0000:00:17.0: reg 0x18: [io  0xf050-0xf057]
[    0.147545] pci 0000:00:17.0: reg 0x1c: [io  0xf040-0xf043]
[    0.147550] pci 0000:00:17.0: reg 0x20: [io  0xf020-0xf03f]
[    0.147555] pci 0000:00:17.0: reg 0x24: [mem 0xefe4b000-0xefe4b7ff]
[    0.147584] pci 0000:00:17.0: PME# supported from D3hot
[    0.147723] pci 0000:00:1b.0: [8086:a2e7] type 01 class 0x060400
[    0.147774] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.147981] pci 0000:00:1b.4: [8086:a2eb] type 01 class 0x060400
[    0.148039] pci 0000:00:1b.4: PME# supported from D0 D3hot D3cold
[    0.148249] pci 0000:00:1c.0: [8086:a290] type 01 class 0x060400
[    0.148301] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.148508] pci 0000:00:1c.5: [8086:a295] type 01 class 0x060400
[    0.148560] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.148754] pci 0000:00:1c.6: [8086:a296] type 01 class 0x060400
[    0.148805] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[    0.149000] pci 0000:00:1c.7: [8086:a297] type 01 class 0x060400
[    0.149052] pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
[    0.149248] pci 0000:00:1d.0: [8086:a298] type 01 class 0x060400
[    0.149306] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.149519] pci 0000:00:1d.5: [8086:a29d] type 01 class 0x060400
[    0.149570] pci 0000:00:1d.5: PME# supported from D0 D3hot D3cold
[    0.149770] pci 0000:00:1f.0: [8086:a2c5] type 00 class 0x060100
[    0.149985] pci 0000:00:1f.2: [8086:a2a1] type 00 class 0x058000
[    0.149996] pci 0000:00:1f.2: reg 0x10: [mem 0xefe44000-0xefe47fff]
[    0.150165] pci 0000:00:1f.3: [8086:a2f0] type 00 class 0x040300
[    0.150184] pci 0000:00:1f.3: reg 0x10: [mem 0xefe40000-0xefe43fff 64bit]
[    0.150210] pci 0000:00:1f.3: reg 0x20: [mem 0xefe20000-0xefe2ffff 64bit]
[    0.150250] pci 0000:00:1f.3: PME# supported from D3hot D3cold
[    0.150472] pci 0000:00:1f.4: [8086:a2a3] type 00 class 0x0c0500
[    0.150528] pci 0000:00:1f.4: reg 0x10: [mem 0xefe4a000-0xefe4a0ff 64bit]
[    0.150597] pci 0000:00:1f.4: reg 0x20: [io  0xf000-0xf01f]
[    0.150805] pci 0000:00:1f.6: [8086:15b8] type 00 class 0x020000
[    0.150821] pci 0000:00:1f.6: reg 0x10: [mem 0xefe00000-0xefe1ffff]
[    0.150913] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
[    0.151077] pci 0000:01:00.0: [1002:1478] type 01 class 0x060400
[    0.151086] pci 0000:01:00.0: reg 0x10: [mem 0xefa00000-0xefa03fff]
[    0.151155] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.151198] pci 0000:01:00.0: 126.016 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x16 link at 0000:00:01.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[    0.151248] pci 0000:00:01.0: PCI bridge to [bus 01-03]
[    0.151249] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.151250] pci 0000:00:01.0:   bridge window [mem 0xef700000-0xefafffff]
[    0.151252] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.151286] pci 0000:02:00.0: [1002:1479] type 01 class 0x060400
[    0.151360] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    0.151424] pci 0000:01:00.0: PCI bridge to [bus 02-03]
[    0.151428] pci 0000:01:00.0:   bridge window [io  0xe000-0xefff]
[    0.151429] pci 0000:01:00.0:   bridge window [mem 0xef700000-0xef9fffff]
[    0.151432] pci 0000:01:00.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.151467] pci 0000:03:00.0: [1002:73bf] type 00 class 0x030000
[    0.151479] pci 0000:03:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.151486] pci 0000:03:00.0: reg 0x18: [mem 0xe0000000-0xe01fffff 64bit pref]
[    0.151491] pci 0000:03:00.0: reg 0x20: [io  0xe000-0xe0ff]
[    0.151496] pci 0000:03:00.0: reg 0x24: [mem 0xef800000-0xef8fffff]
[    0.151501] pci 0000:03:00.0: reg 0x30: [mem 0xef900000-0xef91ffff pref]
[    0.151556] pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.151602] pci 0000:03:00.0: 126.016 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x16 link at 0000:00:01.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[    0.151630] pci 0000:03:00.1: [1002:ab28] type 00 class 0x040300
[    0.151639] pci 0000:03:00.1: reg 0x10: [mem 0xef924000-0xef927fff]
[    0.151707] pci 0000:03:00.1: PME# supported from D1 D2 D3hot D3cold
[    0.151756] pci 0000:03:00.2: [1002:73a6] type 00 class 0x0c0330
[    0.151767] pci 0000:03:00.2: reg 0x10: [mem 0xef700000-0xef7fffff 64bit]
[    0.151833] pci 0000:03:00.2: PME# supported from D0 D3hot D3cold
[    0.151883] pci 0000:03:00.3: [1002:73a4] type 00 class 0x0c8000
[    0.151894] pci 0000:03:00.3: reg 0x10: [mem 0xef920000-0xef923fff 64bit]
[    0.151957] pci 0000:03:00.3: PME# supported from D0 D3hot
[    0.152029] pci 0000:02:00.0: PCI bridge to [bus 03]
[    0.152032] pci 0000:02:00.0:   bridge window [io  0xe000-0xefff]
[    0.152034] pci 0000:02:00.0:   bridge window [mem 0xef700000-0xef9fffff]
[    0.152037] pci 0000:02:00.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.152123] pci 0000:04:00.0: [144d:a808] type 00 class 0x010802
[    0.152139] pci 0000:04:00.0: reg 0x10: [mem 0xefd00000-0xefd03fff 64bit]
[    0.152372] pci 0000:00:1b.0: PCI bridge to [bus 04]
[    0.152375] pci 0000:00:1b.0:   bridge window [mem 0xefd00000-0xefdfffff]
[    0.152440] pci 0000:00:1b.4: PCI bridge to [bus 05]
[    0.152528] pci 0000:06:00.0: [1b21:2142] type 00 class 0x0c0330
[    0.152545] pci 0000:06:00.0: reg 0x10: [mem 0xefc00000-0xefc07fff 64bit]
[    0.152585] pci 0000:06:00.0: enabling Extended Tags
[    0.152642] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[    0.152786] pci 0000:00:1c.0: PCI bridge to [bus 06]
[    0.152789] pci 0000:00:1c.0:   bridge window [mem 0xefc00000-0xefcfffff]
[    0.152871] pci 0000:07:00.0: [1969:e0b1] type 00 class 0x020000
[    0.152892] pci 0000:07:00.0: reg 0x10: [mem 0xefb00000-0xefb3ffff 64bit]
[    0.152901] pci 0000:07:00.0: reg 0x18: [io  0xd000-0xd07f]
[    0.152997] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.153132] pci 0000:00:1c.5: PCI bridge to [bus 07]
[    0.153134] pci 0000:00:1c.5:   bridge window [io  0xd000-0xdfff]
[    0.153135] pci 0000:00:1c.5:   bridge window [mem 0xefb00000-0xefbfffff]
[    0.153197] pci 0000:00:1c.6: PCI bridge to [bus 08]
[    0.153259] pci 0000:00:1c.7: PCI bridge to [bus 09]
[    0.153323] pci 0000:00:1d.0: PCI bridge to [bus 0a]
[    0.153408] pci 0000:0b:00.0: [14e4:43a0] type 00 class 0x028000
[    0.153426] pci 0000:0b:00.0: reg 0x10: [mem 0xef600000-0xef607fff 64bit]
[    0.153437] pci 0000:0b:00.0: reg 0x18: [mem 0xef400000-0xef5fffff 64bit]
[    0.153534] pci 0000:0b:00.0: supports D1 D2
[    0.153535] pci 0000:0b:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.153700] pci 0000:00:1d.5: PCI bridge to [bus 0b]
[    0.153703] pci 0000:00:1d.5:   bridge window [mem 0xef400000-0xef6fffff]
[    0.155156] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155197] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[    0.155236] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155276] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155315] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155353] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155392] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155431] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[    0.155979] iommu: Default domain type: Translated 
[    0.155986] pci 0000:03:00.0: vgaarb: setting as boot VGA device
[    0.155986] pci 0000:03:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.155986] pci 0000:03:00.0: vgaarb: bridge control possible
[    0.155986] vgaarb: loaded
[    0.156070] SCSI subsystem initialized
[    0.156079] libata version 3.00 loaded.
[    0.156079] ACPI: bus type USB registered
[    0.156079] usbcore: registered new interface driver usbfs
[    0.156079] usbcore: registered new interface driver hub
[    0.156079] usbcore: registered new device driver usb
[    0.156079] pps_core: LinuxPPS API ver. 1 registered
[    0.156079] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.156079] PTP clock support registered
[    0.156079] EDAC MC: Ver: 3.0.0
[    0.156083] Registered efivars operations
[    0.156083] NetLabel: Initializing
[    0.156083] NetLabel:  domain hash size = 128
[    0.156083] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.156083] NetLabel:  unlabeled traffic allowed by default
[    0.156083] PCI: Using ACPI for IRQ routing
[    0.169058] PCI: pci_cache_line_size set to 64 bytes
[    0.169111] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
[    0.169112] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[    0.169112] e820: reserve RAM buffer [mem 0xb32a2018-0xb3ffffff]
[    0.169112] e820: reserve RAM buffer [mem 0xb32b3018-0xb3ffffff]
[    0.169113] e820: reserve RAM buffer [mem 0xb32c0018-0xb3ffffff]
[    0.169113] e820: reserve RAM buffer [mem 0xb4ade000-0xb7ffffff]
[    0.169114] e820: reserve RAM buffer [mem 0xbc6e2000-0xbfffffff]
[    0.169114] e820: reserve RAM buffer [mem 0xbdcc6000-0xbfffffff]
[    0.169115] e820: reserve RAM buffer [mem 0xbe1ae000-0xbfffffff]
[    0.169115] e820: reserve RAM buffer [mem 0xbf800000-0xbfffffff]
[    0.169116] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff]
[    0.169514] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.169515] hpet0: 8 comparators, 64-bit 24.000000 MHz counter
[    0.171567] clocksource: Switched to clocksource tsc-early
[    0.173724] VFS: Disk quotas dquot_6.6.0
[    0.173724] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.173724] pnp: PnP ACPI init
[    0.173724] system 00:00: [io  0x0a00-0x0a2f] has been reserved
[    0.173724] system 00:00: [io  0x0a30-0x0a3f] has been reserved
[    0.173724] system 00:00: [io  0x0a40-0x0a4f] has been reserved
[    0.173724] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.173724] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.173724] system 00:01: [io  0xffff] has been reserved
[    0.173724] system 00:01: [io  0xffff] has been reserved
[    0.173724] system 00:01: [io  0xffff] has been reserved
[    0.173724] system 00:01: [io  0x1800-0x18fe] has been reserved
[    0.173724] system 00:01: [io  0x164e-0x164f] has been reserved
[    0.173724] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.173724] system 00:02: [io  0x0800-0x087f] has been reserved
[    0.173724] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.173724] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.173724] system 00:04: [io  0x1854-0x1857] has been reserved
[    0.173724] system 00:04: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.176119] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.176120] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.176121] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.176121] system 00:05: [mem 0xf0000000-0xf7ffffff] has been reserved
[    0.176122] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.176122] system 00:05: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.176123] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.176124] system 00:05: [mem 0xff000000-0xffffffff] has been reserved
[    0.176124] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.176125] system 00:05: [mem 0xeffe0000-0xefffffff] has been reserved
[    0.176127] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.176158] system 00:06: [mem 0xfd000000-0xfdabffff] has been reserved
[    0.176159] system 00:06: [mem 0xfdad0000-0xfdadffff] has been reserved
[    0.176159] system 00:06: [mem 0xfdb00000-0xfdffffff] has been reserved
[    0.176160] system 00:06: [mem 0xfe000000-0xfe01ffff] could not be reserved
[    0.176161] system 00:06: [mem 0xfe036000-0xfe03bfff] has been reserved
[    0.176161] system 00:06: [mem 0xfe03d000-0xfe3fffff] has been reserved
[    0.176162] system 00:06: [mem 0xfe410000-0xfe7fffff] has been reserved
[    0.176164] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.176366] system 00:07: [io  0xff00-0xfffe] has been reserved
[    0.176367] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177181] system 00:08: [mem 0xfdaf0000-0xfdafffff] has been reserved
[    0.177182] system 00:08: [mem 0xfdae0000-0xfdaeffff] has been reserved
[    0.177183] system 00:08: [mem 0xfdac0000-0xfdacffff] has been reserved
[    0.177184] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177813] pnp: PnP ACPI: found 9 devices
[    0.182935] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.182966] NET: Registered protocol family 2
[    0.183047] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.183086] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.183175] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[    0.183212] TCP: Hash tables configured (established 131072 bind 65536)
[    0.183246] MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear)
[    0.183275] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.183297] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.183343] NET: Registered protocol family 1
[    0.183345] NET: Registered protocol family 44
[    0.183353] pci 0000:02:00.0: PCI bridge to [bus 03]
[    0.183354] pci 0000:02:00.0:   bridge window [io  0xe000-0xefff]
[    0.183357] pci 0000:02:00.0:   bridge window [mem 0xef700000-0xef9fffff]
[    0.183359] pci 0000:02:00.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183362] pci 0000:01:00.0: PCI bridge to [bus 02-03]
[    0.183363] pci 0000:01:00.0:   bridge window [io  0xe000-0xefff]
[    0.183366] pci 0000:01:00.0:   bridge window [mem 0xef700000-0xef9fffff]
[    0.183367] pci 0000:01:00.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183370] pci 0000:00:01.0: PCI bridge to [bus 01-03]
[    0.183371] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.183372] pci 0000:00:01.0:   bridge window [mem 0xef700000-0xefafffff]
[    0.183374] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183376] pci 0000:00:1b.0: PCI bridge to [bus 04]
[    0.183378] pci 0000:00:1b.0:   bridge window [mem 0xefd00000-0xefdfffff]
[    0.183381] pci 0000:00:1b.4: PCI bridge to [bus 05]
[    0.183387] pci 0000:00:1c.0: PCI bridge to [bus 06]
[    0.183389] pci 0000:00:1c.0:   bridge window [mem 0xefc00000-0xefcfffff]
[    0.183393] pci 0000:00:1c.5: PCI bridge to [bus 07]
[    0.183394] pci 0000:00:1c.5:   bridge window [io  0xd000-0xdfff]
[    0.183396] pci 0000:00:1c.5:   bridge window [mem 0xefb00000-0xefbfffff]
[    0.183399] pci 0000:00:1c.6: PCI bridge to [bus 08]
[    0.183405] pci 0000:00:1c.7: PCI bridge to [bus 09]
[    0.183410] pci 0000:00:1d.0: PCI bridge to [bus 0a]
[    0.183416] pci 0000:00:1d.5: PCI bridge to [bus 0b]
[    0.183418] pci 0000:00:1d.5:   bridge window [mem 0xef400000-0xef6fffff]
[    0.183422] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.183422] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.183423] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.183424] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xefffffff window]
[    0.183424] pci_bus 0000:00: resource 8 [mem 0xfd000000-0xfe7fffff window]
[    0.183425] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.183425] pci_bus 0000:01: resource 1 [mem 0xef700000-0xefafffff]
[    0.183426] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183426] pci_bus 0000:02: resource 0 [io  0xe000-0xefff]
[    0.183427] pci_bus 0000:02: resource 1 [mem 0xef700000-0xef9fffff]
[    0.183427] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183428] pci_bus 0000:03: resource 0 [io  0xe000-0xefff]
[    0.183428] pci_bus 0000:03: resource 1 [mem 0xef700000-0xef9fffff]
[    0.183429] pci_bus 0000:03: resource 2 [mem 0xd0000000-0xe01fffff 64bit pref]
[    0.183429] pci_bus 0000:04: resource 1 [mem 0xefd00000-0xefdfffff]
[    0.183430] pci_bus 0000:06: resource 1 [mem 0xefc00000-0xefcfffff]
[    0.183430] pci_bus 0000:07: resource 0 [io  0xd000-0xdfff]
[    0.183431] pci_bus 0000:07: resource 1 [mem 0xefb00000-0xefbfffff]
[    0.183431] pci_bus 0000:0b: resource 1 [mem 0xef400000-0xef6fffff]
[    0.208179] pci 0000:00:14.0: quirk_usb_early_handoff+0x0/0x6e0 took 24067 usecs
[    0.208211] pci 0000:03:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.208223] pci 0000:03:00.1: D0 power state depends on 0000:03:00.0
[    0.208433] pci 0000:06:00.0: PME# does not work under D0, disabling it
[    0.208653] PCI: CLS 64 bytes, default 64
[    0.208671] Trying to unpack rootfs image as initramfs...
[    0.290710] Freeing initrd memory: 13296K
[    0.290734] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.290735] software IO TLB: mapped [mem 0xaf2a2000-0xb32a2000] (64MB)
[    0.290855] check: Scanning for low memory corruption every 60 seconds
[    0.291042] Initialise system trusted keyrings
[    0.291050] Key type blacklist registered
[    0.291074] workingset: timestamp_bits=41 max_order=22 bucket_order=0
[    0.291648] zbud: loaded
[    0.296412] Key type asymmetric registered
[    0.296413] Asymmetric key parser 'x509' registered
[    0.296417] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.296437] io scheduler mq-deadline registered
[    0.296437] io scheduler kyber registered
[    0.296447] io scheduler bfq registered
[    0.297531] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.297574] intel_idle: MWAIT substates: 0x142120
[    0.297574] intel_idle: v0.5.1 model 0x9E
[    0.297759] intel_idle: Local APIC timer is reliable in all C-states
[    0.297812] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[    0.297823] ACPI: Sleep Button [SLPB]
[    0.297838] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    0.297846] ACPI: Power Button [PWRB]
[    0.297861] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.299375] ACPI: Power Button [PWRF]
[    0.300010] thermal LNXTHERM:00: registered as thermal_zone0
[    0.300010] ACPI: Thermal Zone [TZ00] (28 C)
[    0.300111] thermal LNXTHERM:01: registered as thermal_zone1
[    0.300112] ACPI: Thermal Zone [TZ01] (30 C)
[    0.300281] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.300896] AMD-Vi: AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[    0.300897] AMD-Vi: AMD IOMMUv2 functionality not available on this system
[    0.301408] nvme nvme0: pci function 0000:04:00.0
[    0.301421] ahci 0000:00:17.0: version 3.0
[    0.301580] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 3 ports 6 Gbps 0xd impl SATA mode
[    0.301581] ahci 0000:00:17.0: flags: 64bit ncq sntf pm led clo only pio slum part ems deso sadm sds apst 
[    0.309981] nvme nvme0: missing or invalid SUBNQN field.
[    0.309991] nvme nvme0: Shutdown timeout set to 8 seconds
[    0.319812] scsi host0: ahci
[    0.320071] scsi host1: ahci
[    0.320252] scsi host2: ahci
[    0.320394] scsi host3: ahci
[    0.320416] ata1: SATA max UDMA/133 abar m2048@0xefe4b000 port 0xefe4b100 irq 131
[    0.320416] ata2: DUMMY
[    0.320417] ata3: SATA max UDMA/133 abar m2048@0xefe4b000 port 0xefe4b200 irq 131
[    0.320418] ata4: SATA max UDMA/133 abar m2048@0xefe4b000 port 0xefe4b280 irq 131
[    0.320445] usbcore: registered new interface driver usbserial_generic
[    0.320447] usbserial: USB Serial support registered for generic
[    0.320458] rtc_cmos 00:03: RTC can wake from S4
[    0.320905] rtc_cmos 00:03: registered as rtc0
[    0.321000] rtc_cmos 00:03: setting system clock to 2020-11-20T19:31:11 UTC (1605900671)
[    0.321008] rtc_cmos 00:03: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    0.321036] intel_pstate: Intel P-state driver initializing
[    0.321188] intel_pstate: Disabling energy efficiency optimization
[    0.321188] intel_pstate: HWP enabled
[    0.321221] ledtrig-cpu: registered to indicate activity on CPUs
[    0.321250] resource sanity check: requesting [mem 0xfdffe800-0xfe0007ff], which spans more than pnp 00:06 [mem 0xfdb00000-0xfdffffff]
[    0.321253] caller pmc_core_probe+0x85/0x380 mapping multiple BARs
[    0.321273] intel_pmc_core INT33A1:00:  initialized
[    0.321322] drop_monitor: Initializing network drop monitor service
[    0.321401] NET: Registered protocol family 10
[    0.322131] nvme nvme0: 8/0/0 default/read/poll queues
[    0.324684] Segment Routing with IPv6
[    0.324685] RPL Segment Routing with IPv6
[    0.324698] NET: Registered protocol family 17
[    0.325109] microcode: sig=0x906e9, pf=0x2, revision=0xde
[    0.325244] microcode: Microcode Update Driver: v2.2.
[    0.325246] IPI shorthand broadcast: enabled
[    0.325251] sched_clock: Marking stable (324869466, 372819)->(330778445, -5536160)
[    0.325396] registered taskstats version 1
[    0.325401] Loading compiled-in X.509 certificates
[    0.325695]  nvme0n1: p1 p2 p3
[    0.327379] Loaded X.509 cert 'Build time autogenerated kernel key: 00e32af39d4a2635c8d60f93bbd3e041fd36fd45'
[    0.327516] zswap: loaded using pool lz4/z3fold
[    0.327643] Key type ._fscrypt registered
[    0.327643] Key type .fscrypt registered
[    0.327644] Key type fscrypt-provisioning registered
[    0.328862] PM:   Magic number: 12:29:547
[    0.328963] RAS: Correctable Errors collector initialized.
[    0.636075] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    0.636104] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    0.636129] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    0.636773] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT2._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.636809] fbcon: Taking over console
[    0.636821] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT2._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.637141] ata3.00: ATA-9: WDC WD3003FZEX-00Z4SA0, 01.01A01, max UDMA/133
[    0.637146] ata3.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    0.637888] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT2._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.637917] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT2._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.638149] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT0._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.638179] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT0._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.638305] ata1.00: supports DRM functions and may not be fully accessible
[    0.638327] ata3.00: configured for UDMA/133
[    0.638938] ata1.00: disabling queued TRIM support
[    0.638943] ata1.00: ATA-9: Samsung SSD 840 EVO 250GB, EXT0DB6Q, max UDMA/133
[    0.638947] ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 32), AA
[    0.640041] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT0._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.640070] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT0._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.640132] ata1.00: supports DRM functions and may not be fully accessible
[    0.640715] ata1.00: disabling queued TRIM support
[    0.641288] ata1.00: configured for UDMA/133
[    0.641545] scsi 0:0:0:0: Direct-Access     ATA      Samsung SSD 840  DB6Q PQ: 0 ANSI: 5
[    0.642040] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[    0.642061] sd 0:0:0:0: [sda] Write Protect is off
[    0.642066] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.642098] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.642231] scsi 2:0:0:0: Direct-Access     ATA      WDC WD3003FZEX-0 1A01 PQ: 0 ANSI: 5
[    0.642752] sd 2:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[    0.642758] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[    0.642791] sd 2:0:0:0: [sdb] Write Protect is off
[    0.642796] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    0.642850] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.645091]  sda: sda1 sda2 sda3 sda4
[    0.645932] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT3._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.645962] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT3._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.646916] ata4.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133
[    0.646921] ata4.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    0.647018] sd 0:0:0:0: [sda] supports TCG Opal
[    0.647023] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.656925] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.SAT0.PRT3._GTF.DSSP], AE_NOT_FOUND (20200717/psargs-330)
[    0.656954] ACPI Error: Aborting method \_SB.PCI0.SAT0.PRT3._GTF due to previous error (AE_NOT_FOUND) (20200717/psparse-529)
[    0.657979] ata4.00: configured for UDMA/133
[    0.658220] scsi 3:0:0:0: Direct-Access     ATA      WDC WD30EZRX-00M 0A80 PQ: 0 ANSI: 5
[    0.658671] sd 3:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[    0.658676] sd 3:0:0:0: [sdc] 4096-byte physical blocks
[    0.658695] sd 3:0:0:0: [sdc] Write Protect is off
[    0.658699] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    0.658729] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.673317]  sdb: sdb1
[    0.674144] sd 2:0:0:0: [sdb] Attached SCSI disk
[    0.703606]  sdc: sdc1 sdc2
[    0.704556] sd 3:0:0:0: [sdc] Attached SCSI disk
[    0.708618] Freeing unused decrypted memory: 2040K
[    0.709421] Freeing unused kernel image (initmem) memory: 1660K
[    0.726121] Write protecting the kernel read-only data: 24576k
[    0.727558] Freeing unused kernel image (text/rodata gap) memory: 2044K
[    0.727922] Freeing unused kernel image (rodata/data gap) memory: 244K
[    0.802935] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.802936] x86/mm: Checking user space page tables
[    0.834422] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.834424] Run /init as init process
[    0.834424]   with arguments:
[    0.834424]     /init
[    0.834425]   with environment:
[    0.834425]     HOME=/
[    0.834425]     TERM=linux
[    0.957759] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.957763] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    0.958825] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810
[    0.958828] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    0.958967] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    0.958969] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.958969] usb usb1: Product: xHCI Host Controller
[    0.958970] usb usb1: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    0.958971] usb usb1: SerialNumber: 0000:00:14.0
[    0.959047] hub 1-0:1.0: USB hub found
[    0.959062] hub 1-0:1.0: 16 ports detected
[    0.960806] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.960807] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    0.960809] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[    0.960830] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[    0.960831] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.960831] usb usb2: Product: xHCI Host Controller
[    0.960832] usb usb2: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    0.960832] usb usb2: SerialNumber: 0000:00:14.0
[    0.960925] hub 2-0:1.0: USB hub found
[    0.960939] hub 2-0:1.0: 10 ports detected
[    0.963646] usb: port power management may be unreliable
[    0.963869] xhci_hcd 0000:03:00.2: xHCI Host Controller
[    0.963872] xhci_hcd 0000:03:00.2: new USB bus registered, assigned bus number 3
[    0.963956] xhci_hcd 0000:03:00.2: hcc params 0x0260ffe5 hci version 0x110 quirks 0x0000000000000010
[    0.964186] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    0.964187] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.964188] usb usb3: Product: xHCI Host Controller
[    0.964189] usb usb3: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    0.964190] usb usb3: SerialNumber: 0000:03:00.2
[    0.964954] hub 3-0:1.0: USB hub found
[    0.964966] hub 3-0:1.0: 2 ports detected
[    0.965298] xhci_hcd 0000:03:00.2: xHCI Host Controller
[    0.965300] xhci_hcd 0000:03:00.2: new USB bus registered, assigned bus number 4
[    0.965302] xhci_hcd 0000:03:00.2: Host supports USB 3.1 Enhanced SuperSpeed
[    0.965316] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    0.965335] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[    0.965336] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.965345] usb usb4: Product: xHCI Host Controller
[    0.965346] usb usb4: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    0.965347] usb usb4: SerialNumber: 0000:03:00.2
[    0.965412] hub 4-0:1.0: USB hub found
[    0.965432] hub 4-0:1.0: 1 port detected
[    0.965694] xhci_hcd 0000:06:00.0: xHCI Host Controller
[    0.965697] xhci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 5
[    0.968719] random: fast init done
[    1.020492] xhci_hcd 0000:06:00.0: hcc params 0x0200ef80 hci version 0x110 quirks 0x0000000000800010
[    1.020660] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    1.020660] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.020661] usb usb5: Product: xHCI Host Controller
[    1.020662] usb usb5: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    1.020662] usb usb5: SerialNumber: 0000:06:00.0
[    1.020719] hub 5-0:1.0: USB hub found
[    1.020723] hub 5-0:1.0: 2 ports detected
[    1.020801] xhci_hcd 0000:06:00.0: xHCI Host Controller
[    1.020802] xhci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 6
[    1.020804] xhci_hcd 0000:06:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[    1.020827] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.020837] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[    1.020837] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.020838] usb usb6: Product: xHCI Host Controller
[    1.020838] usb usb6: Manufacturer: Linux 5.9.9-arch1-1 xhci-hcd
[    1.020839] usb usb6: SerialNumber: 0000:06:00.0
[    1.020882] hub 6-0:1.0: USB hub found
[    1.020886] hub 6-0:1.0: 2 ports detected
[    1.266060] usb 1-11: new high-speed USB device number 2 using xhci_hcd
[    1.269383] usb 3-2: new full-speed USB device number 2 using xhci_hcd
[    1.279398] tsc: Refined TSC clocksource calibration: 4199.998 MHz
[    1.279414] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x3c8a5f8911c, max_idle_ns: 440795307124 ns
[    1.279489] clocksource: Switched to clocksource tsc
[    1.407538] usb 1-11: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=32.98
[    1.407543] usb 1-11: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.407547] usb 1-11: Product: USB2.0 Hub
[    1.408656] hub 1-11:1.0: USB hub found
[    1.408975] hub 1-11:1.0: 4 ports detected
[    1.432335] usb 3-2: New USB device found, idVendor=2516, idProduct=014d, bcdDevice= 1.04
[    1.432340] usb 3-2: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[    1.432343] usb 3-2: Product: ARES
[    1.432347] usb 3-2: Manufacturer: Cooler Master Technology Inc.
[    1.458486] hid: raw HID events driver (C) Jiri Kosina
[    1.478582] usbcore: registered new interface driver usbhid
[    1.478585] usbhid: USB HID core driver
[    1.483697] input: Cooler Master Technology Inc. ARES as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.2/usb3/3-2/3-2:1.0/0003:2516:014D.0001/input/input3
[    1.532722] usb 1-12: new full-speed USB device number 3 using xhci_hcd
[    1.539471] hid-generic 0003:2516:014D.0001: input,hidraw0: USB HID v1.11 Keyboard [Cooler Master Technology Inc. ARES] on usb-0000:03:00.2-2/input0
[    1.539767] hid-generic 0003:2516:014D.0002: hiddev0,hidraw1: USB HID v1.11 Device [Cooler Master Technology Inc. ARES] on usb-0000:03:00.2-2/input1
[    1.539897] input: Cooler Master Technology Inc. ARES System Control as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.2/usb3/3-2/3-2:1.2/0003:2516:014D.0003/input/input4
[    1.586205] EXT4-fs (nvme0n1p3): mounted filesystem with ordered data mode. Opts: (null)
[    1.596057] input: Cooler Master Technology Inc. ARES Consumer Control as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.2/usb3/3-2/3-2:1.2/0003:2516:014D.0003/input/input5
[    1.596156] hid-generic 0003:2516:014D.0003: input,hidraw2: USB HID v1.11 Device [Cooler Master Technology Inc. ARES] on usb-0000:03:00.2-2/input2
[    1.679289] usb 1-12: New USB device found, idVendor=046d, idProduct=c066, bcdDevice=58.02
[    1.679292] usb 1-12: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.679294] usb 1-12: Product: G9x Laser Mouse
[    1.679296] usb 1-12: Manufacturer: Logitech
[    1.679298] usb 1-12: SerialNumber: B8CA32E9CE0018
[    1.682440] input: Logitech G9x Laser Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-12/1-12:1.0/0003:046D:C066.0004/input/input6
[    1.682493] hid-generic 0003:046D:C066.0004: input,hidraw3: USB HID v1.11 Mouse [Logitech G9x Laser Mouse] on usb-0000:00:14.0-12/input0
[    1.685004] input: Logitech G9x Laser Mouse Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-12/1-12:1.1/0003:046D:C066.0005/input/input7
[    1.688606] random: crng init done
[    1.688644] systemd[1]: Successfully credited entropy passed from boot loader.
[    1.691153] systemd[1]: systemd 246.6-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    1.706126] systemd[1]: Detected architecture x86-64.
[    1.734194] systemd[1]: Set hostname to <handl3vogn>.
[    1.739425] input: Logitech G9x Laser Mouse Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-12/1-12:1.1/0003:046D:C066.0005/input/input8
[    1.739642] hid-generic 0003:046D:C066.0005: input,hiddev1,hidraw4: USB HID v1.11 Keyboard [Logitech G9x Laser Mouse] on usb-0000:00:14.0-12/input1
[    1.749375] usb 1-11.2: new full-speed USB device number 4 using xhci_hcd
[    1.841736] usb 1-11.2: New USB device found, idVendor=0665, idProduct=6000, bcdDevice= 0.97
[    1.841738] usb 1-11.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.841739] usb 1-11.2: Product: Gaming keyboard
[    1.841740] usb 1-11.2: Manufacturer: EST
[    1.849796] input: EST Gaming keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11.2/1-11.2:1.0/0003:0665:6000.0006/input/input11
[    1.880030] systemd[1]: Queued start job for default target Graphical Interface.
[    1.880955] systemd[1]: Created slice system-getty.slice.
[    1.881200] systemd[1]: Created slice system-modprobe.slice.
[    1.881408] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    1.881627] systemd[1]: Created slice User and Session Slice.
[    1.881702] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    1.881771] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    1.881925] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    1.881977] systemd[1]: Reached target Local Encrypted Volumes.
[    1.882010] systemd[1]: Reached target Login Prompts.
[    1.882052] systemd[1]: Reached target Remote File Systems.
[    1.882083] systemd[1]: Reached target Slices.
[    1.882166] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[    1.882258] systemd[1]: Listening on LVM2 metadata daemon socket.
[    1.882430] systemd[1]: Listening on LVM2 poll daemon socket.
[    1.883665] systemd[1]: Listening on Process Core Dump Socket.
[    1.883807] systemd[1]: Listening on Journal Audit Socket.
[    1.883905] systemd[1]: Listening on Journal Socket (/dev/log).
[    1.884017] systemd[1]: Listening on Journal Socket.
[    1.884124] systemd[1]: Listening on udev Control Socket.
[    1.884211] systemd[1]: Listening on udev Kernel Socket.
[    1.884864] systemd[1]: Mounting Huge Pages File System...
[    1.885549] systemd[1]: Mounting POSIX Message Queue File System...
[    1.886276] systemd[1]: Mounting Kernel Debug File System...
[    1.886900] systemd[1]: Mounting Kernel Trace File System...
[    1.887554] systemd[1]: Starting Create list of static device nodes for the current kernel...
[    1.888159] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[    1.888749] systemd[1]: Starting Load Kernel Module drm...
[    1.889586] systemd[1]: Starting Set Up Additional Binary Formats...
[    1.889647] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    1.890768] systemd[1]: Starting Journal Service...
[    1.891805] systemd[1]: Starting Load Kernel Modules...
[    1.892505] systemd[1]: Starting Remount Root and Kernel File Systems...
[    1.892580] systemd[1]: Condition check resulted in Repartition Root Disk being skipped.
[    1.893371] systemd[1]: Starting Coldplug All udev Devices...
[    1.894523] Linux agpgart interface v0.103
[    1.894663] systemd[1]: Mounted Huge Pages File System.
[    1.894806] systemd[1]: Mounted POSIX Message Queue File System.
[    1.894934] systemd[1]: Mounted Kernel Debug File System.
[    1.895064] systemd[1]: Mounted Kernel Trace File System.
[    1.895519] systemd[1]: Finished Create list of static device nodes for the current kernel.
[    1.895703] systemd[1]: proc-sys-fs-binfmt_misc.automount: Got automount request for /proc/sys/fs/binfmt_misc, triggered by 258 (systemd-binfmt)
[    1.896596] systemd[1]: Mounting Arbitrary Executable File Formats File System...
[    1.898097] systemd[1]: Mounted Arbitrary Executable File Formats File System.
[    1.898489] EXT4-fs (nvme0n1p3): re-mounted. Opts: (null)
[    1.899159] systemd[1]: Finished Set Up Additional Binary Formats.
[    1.899582] systemd[1]: Finished Remount Root and Kernel File Systems.
[    1.899768] systemd[1]: Condition check resulted in First Boot Wizard being skipped.
[    1.900025] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[    1.900648] systemd[1]: Starting Load/Save Random Seed...
[    1.900715] systemd[1]: Condition check resulted in Create System Users being skipped.
[    1.901334] systemd[1]: Starting Create Static Device Nodes in /dev...
[    1.902082] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.902110] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    1.902136] sd 3:0:0:0: Attached scsi generic sg2 type 0
[    1.909357] hid-generic 0003:0665:6000.0006: input,hidraw5: USB HID v1.11 Keyboard [EST Gaming keyboard] on usb-0000:00:14.0-11.2/input0
[    1.909987] input: EST Gaming keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11.2/1-11.2:1.1/0003:0665:6000.0007/input/input12
[    1.912510] systemd[1]: Finished Load/Save Random Seed.
[    1.914416] systemd[1]: Finished Create Static Device Nodes in /dev.
[    1.915390] systemd[1]: Starting Rule-based Manager for Device Events and Files...
[    1.915617] systemd[1]: modprobe@drm.service: Succeeded.
[    1.915861] systemd[1]: Finished Load Kernel Module drm.
[    1.915945] vboxdrv: loading out-of-tree module taints kernel.
[    1.916050] vboxdrv: module verification failed: signature and/or required key missing - tainting kernel
[    1.918269] vboxdrv: Found 8 processor cores
[    1.939620] vboxdrv: TSC mode is Invariant, tentative frequency 4199997605 Hz
[    1.939620] vboxdrv: Successfully loaded version 6.1.16 (interface 0x00300000)
[    1.940227] VBoxNetAdp: Successfully started.
[    1.941374] VBoxNetFlt: Successfully started.
[    1.943659] systemd[1]: Finished Load Kernel Modules.
[    1.943849] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[    1.944445] systemd[1]: Mounting Kernel Configuration File System...
[    1.945027] systemd[1]: Starting Apply Kernel Variables...
[    1.945731] systemd[1]: Mounted Kernel Configuration File System.
[    1.955254] systemd[1]: Finished Coldplug All udev Devices.
[    1.966033] hid-generic 0003:0665:6000.0007: input,hidraw6: USB HID v1.11 Device [EST Gaming keyboard] on usb-0000:00:14.0-11.2/input1
[    1.966521] input: EST Gaming keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11.2/1-11.2:1.2/0003:0665:6000.0008/input/input13
[    1.966775] systemd[1]: Finished Apply Kernel Variables.
[    2.022675] hid-generic 0003:0665:6000.0008: input,hidraw7: USB HID v1.11 Keyboard [EST Gaming keyboard] on usb-0000:00:14.0-11.2/input2
[    2.101063] systemd[1]: Started Journal Service.
[    2.101159] audit: type=1130 audit(1605900673.275:2): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journald comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.143489] audit: type=1130 audit(1605900673.318:3): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udevd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.144096] audit: type=1130 audit(1605900673.318:4): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=lvm2-lvmetad comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.195689] audit: type=1130 audit(1605900673.368:5): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journal-flush comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.232308] wmi_bus wmi_bus-PNP0C14:01: WQAA data block query control method not found
[    2.269585] Adding 7863292k swap on /dev/nvme0n1p2.  Priority:-2 extents:1 across:7863292k SSFS
[    2.320137] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[    2.322626] e1000e: Intel(R) PRO/1000 Network Driver
[    2.322626] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.322964] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    2.323552] bcma-pci-bridge 0000:0b:00.0: enabling device (0000 -> 0002)
[    2.323560] input: PC Speaker as /devices/platform/pcspkr/input/input14
[    2.323609] bcma-pci-bridge 0000:0b:00.0: bus0: Found chip with id 0x4360, rev 0x03 and package 0x01
[    2.323642] bcma-pci-bridge 0000:0b:00.0: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0)
[    2.323659] bcma-pci-bridge 0000:0b:00.0: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0)
[    2.323691] bcma-pci-bridge 0000:0b:00.0: bus0: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0)
[    2.323726] bcma-pci-bridge 0000:0b:00.0: bus0: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0)
[    2.323743] bcma-pci-bridge 0000:0b:00.0: bus0: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0)
[    2.327746] i801_smbus 0000:00:1f.4: enabling device (0001 -> 0003)
[    2.327864] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[    2.327893] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[    2.328323] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 655360 ms ovfl timer
[    2.328324] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[    2.328324] RAPL PMU: hw unit of domain package 2^-14 Joules
[    2.328325] RAPL PMU: hw unit of domain dram 2^-14 Joules
[    2.329221] alx 0000:07:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [1c:1b:0d:93:d6:12]
[    2.329679] mousedev: PS/2 mouse device common for all mice
[    2.335012] i2c i2c-0: 2/4 memory slots populated (from DMI)
[    2.338344] i2c i2c-0: Successfully instantiated SPD at 0x51
[    2.339331] cryptd: max_cpu_qlen set to 1000
[    2.340758] i2c i2c-0: Successfully instantiated SPD at 0x53
[    2.361471] bcma: Unsupported SPROM revision: 11
[    2.361475] bcma-pci-bridge 0000:0b:00.0: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[    2.361476] bcma-pci-bridge 0000:0b:00.0: bus0: Using fallback SPROM failed (err -2)
[    2.361476] bcma-pci-bridge 0000:0b:00.0: bus0: No SPROM available
[    2.364145] bcma-pci-bridge 0000:0b:00.0: bus0: Bus registered
[    2.390878] AVX2 version of gcm_enc/dec engaged.
[    2.390879] AES CTR mode by8 optimization enabled
[    2.403794] audit: type=1130 audit(1605900673.578:6): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=lvm2-monitor comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.424049] audit: type=1130 audit(1605900673.598:7): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-fsck@dev-disk-by\x2duuid-1669\x2dA524 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.463252] snd_hda_intel 0000:03:00.1: Force to non-snoop mode
[    2.475095] alx 0000:07:00.0 enp7s0: renamed from eth0
[    2.483080] iTCO_vendor_support: vendor-support=0
[    2.488348] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[    2.488394] iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400)
[    2.488478] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    2.490009] ee1004 0-0051: 512 byte EE1004-compliant SPD EEPROM, read-only
[    2.490205] ee1004 0-0053: 512 byte EE1004-compliant SPD EEPROM, read-only
[    2.499600] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input15
[    2.499670] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input16
[    2.499703] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input17
[    2.499736] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input18
[    2.499773] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input19
[    2.499806] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:00.0/0000:03:00.1/sound/card1/input20
[    2.541833] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
[    2.589876] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC1220: line_outs=3 (0x14/0x15/0x16/0x0/0x0) type:line
[    2.589878] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    2.589880] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[    2.589881] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[    2.589881] snd_hda_codec_realtek hdaudioC0D0:    dig-out=0x1e/0x0
[    2.589882] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[    2.589883] snd_hda_codec_realtek hdaudioC0D0:      Front Mic=0x19
[    2.589885] snd_hda_codec_realtek hdaudioC0D0:      Rear Mic=0x18
[    2.589886] snd_hda_codec_realtek hdaudioC0D0:      Line=0x1a
[    2.592296] audit: type=1130 audit(1605900673.765:8): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.599563] audit: type=1127 audit(1605900673.775:9): pid=453 uid=0 auid=4294967295 ses=4294967295 msg=' comm="systemd-update-utmp" exe="/usr/lib/systemd/systemd-update-utmp" hostname=? addr=? terminal=? res=success'
[    2.602289] audit: type=1130 audit(1605900673.775:10): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-update-utmp comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[    2.616446] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input21
[    2.616487] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input22
[    2.616524] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1f.3/sound/card0/input23
[    2.616559] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24
[    2.616594] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1f.3/sound/card0/input25
[    2.616626] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1f.3/sound/card0/input26
[    2.616657] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input27
[    2.617949] e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) 1c:1b:0d:93:d6:10
[    2.617951] e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
[    2.618030] e1000e 0000:00:1f.6 eth0: MAC: 12, PHY: 12, PBA No: FFFFFF-0FF
[    2.620069] e1000e 0000:00:1f.6 enp0s31f6: renamed from eth0
[    2.801009] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.802688] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.802868] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.802869] cfg80211: failed to load regulatory.db
[    2.932790] intel_rapl_common: Found RAPL domain package
[    2.932791] intel_rapl_common: Found RAPL domain core
[    2.932792] intel_rapl_common: Found RAPL domain dram
[    2.933052] [drm] amdgpu kernel modesetting enabled.
[    2.933434] CRAT table not found
[    2.933436] Virtual CRAT table created for CPU
[    2.933445] amdgpu: Topology: Add CPU node
[    2.933507] amdgpu 0000:03:00.0: vgaarb: deactivate vga console
[    2.933618] [drm] initializing kernel modesetting (SIENNA_CICHLID 0x1002:0x73BF 0x1002:0x0E3A 0xC1).
[    2.933620] amdgpu 0000:03:00.0: amdgpu: Trusted Memory Zone (TMZ) feature not supported
[    2.933628] [drm] register mmio base: 0xEF800000
[    2.933628] [drm] register mmio size: 1048576
[    2.934699] [drm] add ip block number 0 <nv_common>
[    2.934700] [drm] add ip block number 1 <gmc_v10_0>
[    2.934700] [drm] add ip block number 2 <navi10_ih>
[    2.934701] [drm] add ip block number 3 <psp>
[    2.934701] [drm] add ip block number 4 <smu>
[    2.934702] [drm] add ip block number 5 <dm>
[    2.934703] [drm] add ip block number 6 <gfx_v10_0>
[    2.934703] [drm] add ip block number 7 <sdma_v5_2>
[    2.934704] [drm] add ip block number 8 <vcn_v3_0>
[    2.934704] [drm] add ip block number 9 <jpeg_v3_0>
[    2.934716] amdgpu 0000:03:00.0: No more image in the PCI ROM
[    2.934725] amdgpu: ATOM BIOS: 113-D4120500-101
[    2.934731] [drm] VCN(0) decode is enabled in VM mode
[    2.934732] [drm] VCN(1) decode is enabled in VM mode
[    2.934732] [drm] VCN(0) encode is enabled in VM mode
[    2.934733] [drm] VCN(1) encode is enabled in VM mode
[    2.934734] [drm] JPEG decode is enabled in VM mode
[    2.934751] [drm] vm size is 262144 GB, 4 levels, block size is 9-bit, fragment size is 9-bit
[    2.934757] amdgpu 0000:03:00.0: amdgpu: VRAM: 16368M 0x0000008000000000 - 0x00000083FEFFFFFF (16368M used)
[    2.934758] amdgpu 0000:03:00.0: amdgpu: GART: 512M 0x0000000000000000 - 0x000000001FFFFFFF
[    2.934763] [drm] Detected VRAM RAM=16368M, BAR=256M
[    2.934764] [drm] RAM width 256bits GDDR6
[    2.934822] [TTM] Zone  kernel: Available graphics memory: 8171062 KiB
[    2.934822] [TTM] Zone   dma32: Available graphics memory: 2097152 KiB
[    2.934823] [TTM] Initializing pool allocator
[    2.934825] [TTM] Initializing DMA pool allocator
[    2.934851] [drm] amdgpu: 16368M of VRAM memory ready
[    2.934853] [drm] amdgpu: 11969M of GTT memory ready.
[    2.934854] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    2.934932] [drm] PCIE GART of 512M enabled (table at 0x0000008000000000).
[    2.936131] amdgpu 0000:03:00.0: amdgpu: Unsupported TA type: 6
[    2.994086] b43-phy0: Broadcom 4360 WLAN found (core revision 42)
[    2.994429] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1)
[    2.994439] b43: probe of bcma0:1 failed with error -95
[    2.994454] Broadcom 43xx driver loaded [ Features: PNLS ]
[    4.342712] [drm] Loading DMUB firmware via PSP: version=0x00000000
[    4.345350] [drm] use_doorbell being set to: [true]
[    4.345373] [drm] use_doorbell being set to: [true]
[    4.345394] [drm] use_doorbell being set to: [true]
[    4.345414] [drm] use_doorbell being set to: [true]
[    4.345793] [drm] Found VCN firmware Version ENC: 1.3 DEC: 2 VEP: 0 Revision: 17
[    4.345798] [drm] PSP loading VCN firmware
[    4.532767] [drm] reserve 0xa00000 from 0x83fe000000 for PSP TMR
[    4.722754] amdgpu 0000:03:00.0: amdgpu: smu driver if version = 0x00000034, smu fw if version = 0x0000003b, smu fw version = 0x003a3100 (58.49.0)
[    4.722758] amdgpu 0000:03:00.0: amdgpu: SMU driver if version not matched
[    4.722771] amdgpu 0000:03:00.0: amdgpu: use vbios provided pptable
[    4.792042] amdgpu 0000:03:00.0: amdgpu: SMU is initialized successfully!
[    4.792189] [drm] Display Core initialized with v3.2.95!
[    4.793222] [drm] DMUB hardware initialized: version=0x02000001
[    4.795166] snd_hda_intel 0000:03:00.1: bound 0000:03:00.0 (ops amdgpu_dm_audio_component_bind_ops [amdgpu])
[    4.948964] [drm] kiq ring mec 2 pipe 1 q 0
[    4.971051] [drm] VCN decode and encode initialized successfully(under DPG Mode).
[    4.971250] [drm] JPEG decode initialized successfully.
[    4.975240] kfd kfd: Allocated 3969056 bytes on gart
[    4.977821] Virtual CRAT table created for GPU
[    4.978280] amdgpu: Topology: Add dGPU node [0x73bf:0x1002]
[    4.978287] kfd kfd: added device 1002:73bf
[    4.978292] amdgpu 0000:03:00.0: amdgpu: SE 4, SH per SE 2, CU per SH 10, active_cu_number 72
[    4.982825] [drm] fb mappable at 0xD0332000
[    4.982828] [drm] vram apper at 0xD0000000
[    4.982830] [drm] size 14745600
[    4.982832] [drm] fb depth is 24
[    4.982833] [drm]    pitch is 10240
[    4.983061] fbcon: amdgpudrmfb (fb0) is primary device
[    5.082026] Console: switching to colour frame buffer device 160x45
[    5.093385] amdgpu 0000:03:00.0: [drm] fb0: amdgpudrmfb frame buffer device
[    5.112811] amdgpu 0000:03:00.0: amdgpu: ring gfx_0.0.0 uses VM inv eng 0 on hub 0
[    5.112813] amdgpu 0000:03:00.0: amdgpu: ring comp_1.0.0 uses VM inv eng 1 on hub 0
[    5.112814] amdgpu 0000:03:00.0: amdgpu: ring comp_1.1.0 uses VM inv eng 4 on hub 0
[    5.112816] amdgpu 0000:03:00.0: amdgpu: ring comp_1.2.0 uses VM inv eng 5 on hub 0
[    5.112817] amdgpu 0000:03:00.0: amdgpu: ring comp_1.3.0 uses VM inv eng 6 on hub 0
[    5.112818] amdgpu 0000:03:00.0: amdgpu: ring comp_1.0.1 uses VM inv eng 7 on hub 0
[    5.112819] amdgpu 0000:03:00.0: amdgpu: ring comp_1.1.1 uses VM inv eng 8 on hub 0
[    5.112819] amdgpu 0000:03:00.0: amdgpu: ring comp_1.2.1 uses VM inv eng 9 on hub 0
[    5.112820] amdgpu 0000:03:00.0: amdgpu: ring comp_1.3.1 uses VM inv eng 10 on hub 0
[    5.112821] amdgpu 0000:03:00.0: amdgpu: ring kiq_2.1.0 uses VM inv eng 11 on hub 0
[    5.112823] amdgpu 0000:03:00.0: amdgpu: ring sdma0 uses VM inv eng 12 on hub 0
[    5.112824] amdgpu 0000:03:00.0: amdgpu: ring sdma1 uses VM inv eng 13 on hub 0
[    5.112825] amdgpu 0000:03:00.0: amdgpu: ring sdma2 uses VM inv eng 14 on hub 0
[    5.112826] amdgpu 0000:03:00.0: amdgpu: ring sdma3 uses VM inv eng 15 on hub 0
[    5.112827] amdgpu 0000:03:00.0: amdgpu: ring vcn_dec_0 uses VM inv eng 0 on hub 1
[    5.112828] amdgpu 0000:03:00.0: amdgpu: ring vcn_enc_0.0 uses VM inv eng 1 on hub 1
[    5.112829] amdgpu 0000:03:00.0: amdgpu: ring vcn_enc_0.1 uses VM inv eng 4 on hub 1
[    5.112831] amdgpu 0000:03:00.0: amdgpu: ring vcn_dec_1 uses VM inv eng 5 on hub 1
[    5.112832] amdgpu 0000:03:00.0: amdgpu: ring vcn_enc_1.0 uses VM inv eng 6 on hub 1
[    5.112833] amdgpu 0000:03:00.0: amdgpu: ring vcn_enc_1.1 uses VM inv eng 7 on hub 1
[    5.112834] amdgpu 0000:03:00.0: amdgpu: ring jpeg_dec uses VM inv eng 8 on hub 1
[    5.113984] [drm] Initialized amdgpu 3.39.0 20150101 for 0000:03:00.0 on minor 0
[    8.039852] e1000e 0000:00:1f.6 enp0s31f6: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[    8.039929] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s31f6: link becomes ready
[    8.159574] amdgpu 0000:03:00.0: [drm:amdgpu_ib_ring_tests [amdgpu]] *ERROR* IB test failed on gfx_0.0.0 (-110).
[    8.159922] [drm:process_one_work] *ERROR* ib ring test failed (-110).
[    8.822681] process '/usr/bin/xow' started with executable stack
[   11.098757] kauditd_printk_skb: 36 callbacks suppressed
[   11.098758] audit: type=1130 audit(1605900682.271:47): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-wait-online comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   11.166413] audit: type=1130 audit(1605900682.341:48): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=colord comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   11.230529] audit: type=1130 audit(1605900682.405:49): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=org.cups.cupsd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   13.007150] audit: type=1131 audit(1605900684.181:50): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-dispatcher comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   14.062090] audit: type=1131 audit(1605900685.235:51): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user@120 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   14.066552] audit: type=1131 audit(1605900685.241:52): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user-runtime-dir@120 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   18.663781] audit: type=1100 audit(1605900689.838:53): pid=580 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:authentication grantors=pam_shells,pam_faillock,pam_permit,pam_faillock acct="user" exe="/usr/bin/sshd" hostname=10.0.0.198 addr=10.0.0.198 terminal=ssh res=success'
[   18.679118] audit: type=1101 audit(1605900689.855:54): pid=580 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_permit,pam_time acct="user" exe="/usr/bin/sshd" hostname=10.0.0.198 addr=10.0.0.198 terminal=ssh res=success'
[   18.679700] audit: type=1103 audit(1605900689.855:55): pid=580 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:setcred grantors=pam_shells,pam_faillock,pam_permit,pam_faillock acct="user" exe="/usr/bin/sshd" hostname=10.0.0.198 addr=10.0.0.198 terminal=ssh res=success'
[   18.679702] audit: type=1006 audit(1605900689.855:56): pid=580 uid=0 old-auid=4294967295 auid=1000 tty=(none) old-ses=4294967295 ses=3 res=1
[   18.689955] audit: type=1130 audit(1605900689.865:57): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user-runtime-dir@1000 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   18.695125] audit: type=1101 audit(1605900689.868:58): pid=584 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_permit,pam_time acct="user" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   18.695128] audit: type=1103 audit(1605900689.868:59): pid=584 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:setcred grantors=? acct="user" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=failed'
[   18.695195] audit: type=1006 audit(1605900689.868:60): pid=584 uid=0 old-auid=4294967295 auid=1000 tty=(none) old-ses=4294967295 ses=4 res=1
[   18.696518] audit: type=1105 audit(1605900689.871:61): pid=584 uid=0 auid=1000 ses=4 msg='op=PAM:session_open grantors=pam_loginuid,pam_loginuid,pam_keyinit,pam_limits,pam_unix,pam_permit,pam_mail,pam_systemd,pam_env acct="user" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   18.702536] audit: type=1334 audit(1605900689.875:62): prog-id=12 op=LOAD
[   18.808845] fuse: init (API version 7.31)
[    8.159574] amdgpu 0000:03:00.0: [drm:amdgpu_ib_ring_tests [amdgpu]] *ERROR* IB test failed on gfx_0.0.0 (-110).
[    8.159922] [drm:process_one_work] *ERROR* ib ring test failed (-110).

do you have any more sugestions?

Last edited by Handl3vogn (2020-11-21 01:00:25)

Offline

#6 2020-11-20 19:45:45

loqs
Member
Registered: 2014-03-06
Posts: 12,134

Re: Radeon 6800 / 6800XT graphics

@Handl3vogn Try mesa-git from Unofficial_user_repositories#mesa-git in combination with linux-mainline from Unofficial_user_repositories#miffe.

Offline

#7 2020-11-20 20:09:57

Handl3vogn
Member
Registered: 2020-11-20
Posts: 8

Re: Radeon 6800 / 6800XT graphics

@loqs Mesa repo works fine but getting error trying to add miffe

]# pacman -Sy
:: Synkroniserer pakkedatabaser...
 core er oppdatert
 extra                                                                                    1637,9 KiB  23,9 MiB/s 00:00 [########################################################################] 100%
 community                                                                                   5,2 MiB  54,0 MiB/s 00:00 [########################################################################] 100%
 multilib                                                                                  153,4 KiB  49,9 MiB/s 00:00 [########################################################################] 100%
 mesa-git                                                                                    6,6 KiB  0,00   B/s 00:00 [########################################################################] 100%
 miffe                                                                                       5,1 KiB  0,00   B/s 00:00 [########################################################################] 100%
 miffe.sig                                                                                 310,0   B  0,00   B/s 00:00 [########################################################################] 100%
feil: miffe: nøkkel "4A3417224EBB68E0C1F7FE7D18377D81313F5ABD" er ukjent
:: Importer PGP-nøkkel 4A3417224EBB68E0C1F7FE7D18377D81313F5ABD? [J/n] j
feil: kunne ikke finne nøkkel "4A3417224EBB68E0C1F7FE7D18377D81313F5ABD" på avstand
feil: kunne ikke oppdatere miffe (ugyldig eller korrupt database (PGP signatur))
feil: kunne ikke synkronisere alle databaser

pacman.conf

#
# /etc/pacman.conf
#
# See the pacman.conf(5) manpage for option and repository directives

#
# GENERAL OPTIONS
#
[options]
# The following paths are commented out with their default values listed.
# If you wish to use different paths, uncomment and update the paths.
#RootDir     = /
#DBPath      = /var/lib/pacman/
#CacheDir    = /var/cache/pacman/pkg/
#LogFile     = /var/log/pacman.log
#GPGDir      = /etc/pacman.d/gnupg/
#HookDir     = /etc/pacman.d/hooks/
HoldPkg     = pacman glibc
#XferCommand = /usr/bin/curl -L -C - -f -o %o %u
#XferCommand = /usr/bin/wget --passive-ftp -c -O %o %u
#CleanMethod = KeepInstalled
#UseDelta    = 0.7
Architecture = auto

#IgnorePkg   =
#IgnorePkg   =
#IgnoreGroup =

#NoUpgrade   =
#NoExtract   =

# Misc options
#UseSyslog
Color
#TotalDownload
CheckSpace
#VerbosePkgLists

# By default, pacman accepts packages signed by keys that its local keyring
# trusts (see pacman-key and its man page), as well as unsigned packages.
SigLevel    = Required DatabaseOptional
LocalFileSigLevel = Optional
#RemoteFileSigLevel = Required

# NOTE: You must run `pacman-key --init` before first using pacman; the local
# keyring can then be populated with the keys of all official Arch Linux
# packagers with `pacman-key --populate archlinux`.

#
# REPOSITORIES
#   - can be defined here or included from another file
#   - pacman will search repositories in the order defined here
#   - local/custom mirrors can be added here or in separate files
#   - repositories listed first will take precedence when packages
#     have identical names, regardless of version number
#   - URLs will have $repo replaced by the name of the current repo
#   - URLs will have $arch replaced by the name of the architecture
#
# Repository entries are of the format:
#       [repo-name]
#       Server = ServerName
#       Include = IncludePath
#
# The header [repo-name] is crucial - it must be present and
# uncommented to enable the repo.
#

# The testing repositories are disabled by default. To enable, uncomment the
# repo name header and Include lines. You can add preferred servers immediately
# after the header, and they will be used before the default mirrors.

#[testing]
#Include = /etc/pacman.d/mirrorlist

[core]
Include = /etc/pacman.d/mirrorlist

[extra]
Include = /etc/pacman.d/mirrorlist

#[community-testing]
#Include = /etc/pacman.d/mirrorlist

[community]
Include = /etc/pacman.d/mirrorlist

# If you want to run 32 bit applications on your x86_64 system,
# enable the multilib repositories as required here.

#[multilib-testing]
#Include = /etc/pacman.d/mirrorlist

[multilib]
Include = /etc/pacman.d/mirrorlist

# An example of a custom package repository.  See the pacman manpage for
# tips on creating your own repositories.
#[custom]
#SigLevel = Optional TrustAll
#Server = file:///home/custompkgs

[mesa-git]
Server = https://pkgbuild.com/~lcarlier/$repo/$arch/

[miffe]
Server = https://arch.miffe.org/$arch/

do you kow to fix or ignore this key error?

Edit
Got it wokring so trying to install mesa and mainline kernel now

Last edited by Handl3vogn (2020-11-20 20:26:24)

Offline

#8 2020-11-20 20:23:53

loqs
Member
Registered: 2014-03-06
Posts: 12,134

Re: Radeon 6800 / 6800XT graphics

Offline

#9 2020-11-20 20:31:07

Handl3vogn
Member
Registered: 2020-11-20
Posts: 8

Re: Radeon 6800 / 6800XT graphics

loqs wrote:

Yes but got error on all commands

pacman-key --refresh-keys
gpg: oppdaterer 122 nøkler fra hkps://hkps.pool.sks-keyservers.net
gpg: oppdatering av nøkkeltjener mislyktes: General error
==> FEIL: En angitt lokal nøkkel kunne ikke oppdateres med en nøkkeltjener.

edit

Fixed all key/signature problems by adding this line to /etc/pacman.d/gnupg/gpg.conf under lock-never
Could not get hkps:// to work on any of my arch machines

keyserver hkp://pool.sks-keyservers.net

Last edited by Handl3vogn (2020-11-21 10:53:54)

Offline

#10 2020-11-20 20:44:01

loqs
Member
Registered: 2014-03-06
Posts: 12,134

Re: Radeon 6800 / 6800XT graphics

mesa-git is an unsigned repository.

[mesa-git]
SigLevel = PackageOptional
Server = https://pkgbuild.com/~lcarlier/$repo/$arch

Offline

#11 2020-11-20 20:48:03

Handl3vogn
Member
Registered: 2020-11-20
Posts: 8

Re: Radeon 6800 / 6800XT graphics

@loqs Thanks for your help.
All working now. Booted in to gnome and time to try some games.

Offline

#12 2020-11-21 00:31:54

SyXbiT
Member
From: Seattle, WA
Registered: 2008-06-28
Posts: 173
Website

Re: Radeon 6800 / 6800XT graphics

I also got a 6800 (arrives next week).
Just so I'm clear, per phoronix, linux 5.9 and Mesa 20.2 works, though but Mesa 20.3/21.0-devel doesn't yet.
Only missing piece you need Linux-Firmware.Git, which I think is in linux-firmware-20201118 (not in Arch yet). Assuming Arch merges linux-firmware soon, 6800 should work out of the box

Offline

#13 2020-11-21 00:44:36

Handl3vogn
Member
Registered: 2020-11-20
Posts: 8

Re: Radeon 6800 / 6800XT graphics

@SyXbiT
I did not get it to work with linux 5.9 and Mesa 20.2

I had to install linux-firmware-git, mesa-git and linux-mainline (5.10.0-rc4) in order to get it working.

after just installing linux-firmware-git I got this error and was unable to start X

[    8.159574] amdgpu 0000:03:00.0: [drm:amdgpu_ib_ring_tests [amdgpu]] *ERROR* IB test failed on gfx_0.0.0 (-110).
[    8.159922] [drm:process_one_work] *ERROR* ib ring test failed (-110).

Last edited by Handl3vogn (2020-11-21 00:47:09)

Offline

#14 2020-11-21 00:47:35

loqs
Member
Registered: 2014-03-06
Posts: 12,134

Re: Radeon 6800 / 6800XT graphics

SyXbiT wrote:

Just so I'm clear, per phoronix, linux 5.9 and Mesa 20.2 works, though but Mesa 20.3/21.0-devel doesn't yet.

mesa 20.3 / mesa-git needs linux 5.10-rcX.

SyXbiT wrote:

Only missing piece you need Linux-Firmware.Git, which I think is in linux-firmware-20201118 (not in Arch yet).

20201118 https://git.kernel.org/pub/scm/linux/ke … h=20201118 does not contain the 6800 firmware https://git.kernel.org/pub/scm/linux/ke … 96d4b88102

SyXbiT wrote:

Assuming Arch merges linux-firmware soon, 6800 should work out of the box

Apart from whatever issue Handl3vogn encountered and mesa 20.2 not containing https://gitlab.freedesktop.org/mesa/mes … acad41a98f so the number of compute cores used by the 6800 none XT will be wrong according to the phoronix link.

Offline

#15 2020-11-21 06:40:12

jekb
Member
Registered: 2020-11-20
Posts: 2

Re: Radeon 6800 / 6800XT graphics

thanks for all the help!

I was able to get it working by installing the following:
linux-firmware-git
mesa (not mesa-git)
linux-mainline

I could not get it working without linux-mainline

Last edited by jekb (2020-11-21 06:40:28)

Offline

#16 2020-11-22 05:35:09

SyXbiT
Member
From: Seattle, WA
Registered: 2008-06-28
Posts: 173
Website

Re: Radeon 6800 / 6800XT graphics

jekb wrote:

thanks for all the help!

I was able to get it working by installing the following:
linux-firmware-git
mesa (not mesa-git)
linux-mainline

I could not get it working without linux-mainline

Just to confirm.

linux-firmware.git. I assume you mean not the version in arch repos, but the upstream 'main' or 'master' branch of linux-firmware.git, as in - https://git.kernel.org/pub/scm/linux/ke … it/commit/, which contains https://git.kernel.org/pub/scm/linux/ke … d8f176142d

mesa - The version of mesa in Arch stable repos:  20.2.2-2

linux-mainline. Do you mean 5.10-rc4, or the version in Arch stable repos (5.9.9.arch1-1)

Offline

#17 2020-11-22 05:50:29

loqs
Member
Registered: 2014-03-06
Posts: 12,134

Re: Radeon 6800 / 6800XT graphics

Offline

#18 2020-11-26 03:59:41

rjahanbakhshi
Member
Registered: 2020-11-26
Posts: 2

Re: Radeon 6800 / 6800XT graphics

The latest linux-mainline 5.10.0-rc5-1 with the latest official mesa 20.2.3-1 and the latest linux-firmware-git doesn't work. X11 crashes in amdgpu_dri.so

Could you please provide me the exact working versions you're using.

Downgraded to linux-mainline (5.10.0-rc4) but still no good.
Also downgrading to mesa 20.2.2-2 didn't help.

Offline

#19 2020-11-26 11:09:21

rjahanbakhshi
Member
Registered: 2020-11-26
Posts: 2

Re: Radeon 6800 / 6800XT graphics

rjahanbakhshi wrote:

The latest linux-mainline 5.10.0-rc5-1 with the latest official mesa 20.2.3-1 and the latest linux-firmware-git doesn't work. X11 crashes in amdgpu_dri.so

Could you please provide me the exact working versions you're using.

Downgraded to linux-mainline (5.10.0-rc4) but still no good.
Also downgrading to mesa 20.2.2-2 didn't help.

Never mind. I made a mistake and left amdgpu pro driver installed. After removing it, everything is working. I'm using

Latest linux-mainline 5.10.0-rc5-1
Latest linux-firmware-git Nov 23 2020
Latest mesa-git 21.0.0_devel

I'm also using
lib32-mesa-git
xf86-video-amdgpu-git

So far everything works great. I've been playing some native and proton games. Man this card is a beast.

Last edited by rjahanbakhshi (2020-11-26 12:01:48)

Offline

#20 2020-11-27 07:09:27

konni
Member
From: berlin
Registered: 2008-09-25
Posts: 99

Re: Radeon 6800 / 6800XT graphics

thanks for your suggestions, my 6800 xt arrived yesterday and this helped!

Offline

#21 2020-11-28 16:19:26

Handl3vogn
Member
Registered: 2020-11-20
Posts: 8

Re: Radeon 6800 / 6800XT graphics

After update to linux-firmware in arch repository today you dont need the git version anymore.

Now only thing I need from aur is the linux-mainline kernel (5.10.0-rc5-1)
everything else is from the stock arch repository.

Last edited by Handl3vogn (2020-11-28 16:20:07)

Offline

#22 2020-11-30 05:24:41

SyXbiT
Member
From: Seattle, WA
Registered: 2008-06-28
Posts: 173
Website

Re: Radeon 6800 / 6800XT graphics

Handl3vogn wrote:

After update to linux-firmware in arch repository today you dont need the git version anymore.

Now only thing I need from aur is the linux-mainline kernel (5.10.0-rc5-1)
everything else is from the stock arch repository.

Thanks for following up. While I have my 6800, my PSU and AIO haven't arrived yet (NewEgg w/ Ontrac.... sad  )
Weird needing kernel 5.10. Phoronix said 5.9 worked. Still, easy enough

Offline

#23 2020-12-01 10:06:47

sleax
Member
Registered: 2020-12-01
Posts: 2

Re: Radeon 6800 / 6800XT graphics

I finally have my 6800 (non XT) working well with Arch (fresh install).

Some weirdness though:
* The arch installer fails to boot! Need to quickly press tab and specify nomodeset for the kernel command line to access the terminal.
* Early KMS seems to be required.. otherwise gnome failed with a no drm devices available (workaround if you cant use early KMS is to disable gdm systemd service and start it manually from console)
* linux-mainline-git (5.10-rc5 currently) was required for me too, didn't try anything earlier. 5.9x also gave me "*ERROR* IB test failed on gfx_0.0.0 (-110)"

Optional:
As mentioned earlier you probably want the latest mesa-git (and lib32-mesa-git for steam) if you have a non-XT variant since not all compute units will be active otherwise (at time of writing I don't think this is part of the official packages.. sure it wont be too long though).

linux-firmware is already good to go with official packages.

Last edited by sleax (2020-12-01 10:24:12)

Offline

#24 Yesterday 21:45:07

Handl3vogn
Member
Registered: 2020-11-20
Posts: 8

Re: Radeon 6800 / 6800XT graphics

@sleax
I also had problems with gdm not starting with the system.
Following the arch wiki AMDGPU and "Specify the correct module order" fixed it for me.
https://wiki.archlinux.org/index.php/AM … dule_order

Edit:
Is this the same as early KMS?

Last edited by Handl3vogn (Yesterday 22:16:43)

Offline

#25 Today 01:24:58

sleax
Member
Registered: 2020-12-01
Posts: 2

Re: Radeon 6800 / 6800XT graphics

Handl3vogn wrote:

@sleax
Is this the same as early KMS?

I believe as long as you have amdgpu specified in /etc/mkinitcpio.conf  MOUDLES (..) then it would start with initramfs (early KMS).

My 6800 seems to be working very reliably.. it is a cool and quiet beast!

Offline

Board footer

Powered by FluxBB