You are not logged in.
When I connect the SSD to any USB port I got the following messages on dmesg:
[ 394.228547] usb 2-2: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 394.243603] usb 2-2: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 6.06
[ 394.243607] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 394.243609] usb 2-2: Product: External
[ 394.243610] usb 2-2: Manufacturer: JMicron
[ 394.243611] usb 2-2: SerialNumber: DD56419884719
[ 394.263248] usbcore: registered new interface driver usb-storage
[ 394.269392] scsi host3: uas
[ 394.269454] usbcore: registered new interface driver uas
[ 394.380352] scsi 3:0:0:0: Direct-Access JMicron Tech 0606 PQ: 0 ANSI: 6
[ 394.382488] sd 3:0:0:0: [sdb] 15624192 4096-byte logical blocks: (64.0 GB/59.6 GiB)
[ 394.382589] sd 3:0:0:0: tag#17 data cmplt err -75 uas-tag 1 inflight: CMD
[ 394.382592] sd 3:0:0:0: tag#17 CDB: Mode Sense(6) 1a 00 3f 00 04 00
[ 394.382634] sd 3:0:0:0: [sdb] Write Protect is off
[ 394.382636] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 424.679278] sd 3:0:0:0: tag#18 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[ 424.679291] sd 3:0:0:0: tag#18 CDB: Mode Sense(6) 1a 00 08 00 04 00
[ 424.719314] scsi host3: uas_eh_device_reset_handler start
[ 424.843618] usb 2-2: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 424.861622] scsi host3: uas_eh_device_reset_handler success
[ 424.869434] sd 3:0:0:0: tag#18 data cmplt err -75 uas-tag 1 inflight: CMD
[ 424.869438] sd 3:0:0:0: tag#18 CDB: Mode Sense(6) 1a 00 08 00 04 00
[ 424.869457] sd 3:0:0:0: [sdb] Asking for cache data failed
[ 424.869460] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 455.399439] sd 3:0:0:0: tag#16 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[ 455.399451] sd 3:0:0:0: tag#16 CDB: Inquiry 12 01 00 00 40 00
[ 455.415271] scsi host3: uas_eh_device_reset_handler start
[ 455.540132] usb 2-2: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 455.558676] scsi host3: uas_eh_device_reset_handler success
[ 455.566054] sd 3:0:0:0: [sdb] Optimal transfer size 268431360 bytes
[ 455.592440] sdb: sdb1
[ 455.593977] sd 3:0:0:0: tag#18 data cmplt err -75 uas-tag 1 inflight: CMD
[ 455.593982] sd 3:0:0:0: tag#18 CDB: Mode Sense(6) 1a 00 3f 00 04 00
[ 486.119308] sd 3:0:0:0: tag#19 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[ 486.119312] sd 3:0:0:0: tag#19 CDB: Mode Sense(6) 1a 00 08 00 04 00
[ 486.119401] sd 3:0:0:0: [sdb] tag#9 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD IN
[ 486.119404] sd 3:0:0:0: [sdb] tag#9 CDB: Inquiry 12 00 00 00 24 00
[ 486.163002] scsi host3: uas_eh_device_reset_handler start
[ 486.286858] usb 2-2: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 486.305450] scsi host3: uas_eh_device_reset_handler success
[ 486.308005] sd 3:0:0:0: tag#17 data cmplt err -75 uas-tag 1 inflight: CMD
[ 486.308015] sd 3:0:0:0: tag#17 CDB: Mode Sense(6) 1a 00 08 00 04 00
[ 516.839242] sd 3:0:0:0: tag#18 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[ 516.839246] sd 3:0:0:0: tag#18 CDB: Inquiry 12 01 00 00 40 00
[ 516.842642] sd 3:0:0:0: [sdb] tag#10 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD IN
[ 516.842646] sd 3:0:0:0: [sdb] tag#10 CDB: Read(10) 28 00 00 ee 67 f0 00 00 01 00
[ 516.879633] scsi host3: uas_eh_device_reset_handler start
[ 517.003304] usb 2-2: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 517.022305] scsi host3: uas_eh_device_reset_handler success
[ 517.029441] sd 3:0:0:0: [sdb] Attached SCSI disk
The blank lines between messages denote several seconds.
Before and after connect the SSD:
$ lsusb -t -v
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/8p, 5000M
ID 1d6b:0003 Linux Foundation 3.0 root hub
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/16p, 480M
ID 1d6b:0002 Linux Foundation 2.0 root hub
|__ Port 7: Dev 2, If 0, Class=Wireless, Driver=btusb, 12M
ID 8087:0a2a Intel Corp. Bluetooth wireless interface
|__ Port 7: Dev 2, If 1, Class=Wireless, Driver=btusb, 12M
ID 8087:0a2a Intel Corp. Bluetooth wireless interface
|__ Port 9: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M
ID 04f2:b5f7 Chicony Electronics Co., Ltd
|__ Port 9: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M
ID 04f2:b5f7 Chicony Electronics Co., Ltd
$ lsusb -t -v
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/8p, 5000M
ID 1d6b:0003 Linux Foundation 3.0 root hub
|__ Port 2: Dev 2, If 0, Class=Mass Storage, Driver=uas, 5000M
ID 152d:0562 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/16p, 480M
ID 1d6b:0002 Linux Foundation 2.0 root hub
|__ Port 7: Dev 2, If 0, Class=Wireless, Driver=btusb, 12M
ID 8087:0a2a Intel Corp. Bluetooth wireless interface
|__ Port 7: Dev 2, If 1, Class=Wireless, Driver=btusb, 12M
ID 8087:0a2a Intel Corp. Bluetooth wireless interface
|__ Port 9: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M
ID 04f2:b5f7 Chicony Electronics Co., Ltd
|__ Port 9: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M
ID 04f2:b5f7 Chicony Electronics Co., Ltd
Output of neofetch on my laptop:
-` peracchi@nitro
.o+` --------------
`ooo/ OS: Arch Linux x86_64
`+oooo: Host: Nitro AN515-51 V1.22
`+oooooo: Kernel: 5.11.11-arch1-1
-+oooooo+: Uptime: 10 mins
`/:-:++oooo+: Packages: 997 (pacman)
`/++++/+++++++: Shell: bash 5.1.4
`/++++++++++++++: Resolution: 1920x1080
`/+++ooooooooooooo/` DE: Plasma 5.21.4
./ooosssso++osssssso+` WM: KWin
.oossssso-````/ossssss+` Theme: Breeze Light [Plasma], Breeze [GTK2/3]
-osssssso. :ssssssso. Icons: breeze [Plasma], breeze [GTK2/3]
:osssssss/ osssso+++. Terminal: konsole
/ossssssss/ +ssssooo/- CPU: Intel i7-7700HQ (8) @ 3.800GHz
`/ossssso+/:- -:/+osssso+- GPU: NVIDIA GeForce GTX 1050 Ti Mobile
`+sso+:-` `.-/+oso: GPU: Intel HD Graphics 630
`++:. `-/+/ Memory: 797MiB / 15889MiB
.` `/
Link to product: https://www.dmlifeco.com/solid-state-dr … sb3-1.html
Offline
Try this on Linux:
echo "options usb-storage quirks=152d:0562:u" >> /etc/modprobe.d/usb-storage-quirks.conf
update-initramfs -u
It worked for me.
Last edited by zkp37510 (2022-05-07 13:54:08)
Offline