Arch Linux

teshansj

Member

Registered: 2021-11-17

Posts: 2

New arch installation: No sound output or input devices found [SOLVED]

I am trying arch for the first time. I just set up my laptop (Dell Inspiron 15 5000) with Arch + KDE plasma. Everything is working really well except for sound.

When I click on the muted speaker icon, it shows "No output or input devices found"

$lspci -v gives me

0000:00:1f.3 Multimedia audio controller: Intel Corporation Tiger Lake-LP Smart Sound Technology Audio Controller (rev 20)
        Subsystem: Dell Device 0a02
        Flags: bus master, fast devsel, latency 64, IRQ 16
        Memory at 6035298000 (64-bit, non-prefetchable) [size=16K]
        Memory at 6035000000 (64-bit, non-prefetchable) [size=1M]
        Capabilities: <access denied>
        Kernel driver in use: sof-audio-pci-intel-tgl
        Kernel modules: snd_hda_intel, snd_sof_pci_intel_tgl

sudo fuser -v /dev/snd/* has no output

pacmd xxx commands output as follows

[teshan@mylap ~]$ pacmd list-cards
0 card(s) available.
[teshan@mylap ~]$ pacmd list-sinks
1 sink(s) available.
  * index: 0
        name: <auto_null>
        driver: <module-null-sink.c>
        flags: DECIBEL_VOLUME LATENCY DYNAMIC_LATENCY
        state: SUSPENDED
        suspend cause: IDLE
        priority: 1000
        volume: front-left: 47051 /  72% / -8.63 dB,   front-right: 47051 /  72% / -8.63 dB
                balance 0.00
        base volume: 65536 / 100% / 0.00 dB
        volume steps: 65537
        muted: no
        current latency: 0.00 ms
        max request: 344 KiB
        max rewind: 344 KiB
        monitor source: 0
        sample spec: s16le 2ch 44100Hz
        channel map: front-left,front-right
                     Stereo
        used by: 0
        linked by: 0
        configured latency: 0.00 ms; range is 0.50 .. 2000.00 ms
        module: 11
        properties:
                device.description = "Dummy Output"
                device.class = "abstract"
                device.icon_name = "audio-card"
[teshan@mylap ~]$ pacmd list-sink-inputs
0 sink input(s) available.

I can see that there have been multiple discussions related to the same problem. But none of them had a solution for my problem. Can someone please help me get this resolved? I don't have a clue to where to begin

Last edited by teshansj (2021-11-18 07:32:21)

V1del

Forum Moderator

Registered: 2012-10-16

Posts: 22,195

Re: New arch installation: No sound output or input devices found [SOLVED]

You need to install sof-firmware as a basic requirement, ideally that should be all and it should just work after a reboot.

If you found that in "multiple discussions around the issue", it would be nice to mention what you tried already so we don't have to needlessly repeat ourselves. The last info I have on this is that this was pending on a kernel patch that should be part of the 5.15 kernels we are currently on

Last edited by V1del (2021-11-17 15:00:38)

teshansj

Member

Registered: 2021-11-17

Posts: 2

Re: New arch installation: No sound output or input devices found [SOLVED]

That worked! Thanks. Is this something I have missed from the setup process?

About the other discussions I found, I did not bother to post what I tried because every other post was mentioning losing sound after a while. And they all had their sound devices listed in fuser -v /dev/snd or pacmd list-devices

Scimmia

Fellow

Registered: 2012-09-01

Posts: 11,744

Re: New arch installation: No sound output or input devices found [SOLVED]

That worked! Thanks. Is this something I have missed from the setup process?

https://wiki.archlinux.org/title/Instal … l_packages

3rd bullet point, but it's very hardware dependent.