Arch Linux

Dragonsight91

Member

Registered: 2021-11-28

Posts: 2

[Solved] Problems with MMCONFIG on ACER Iconia W4-820 Series Tablet

I was a bit unsure whether to post this in Laptop Issues or here, since this is sorta both and this thing is not really a laptop, sooo I'm posting it here. While I am new to the forums, I have been using arch for quite some time now and have several custom installations.

To the point: I've been trying to install Arch on this tablet and among a 32bit EFI (which I already got working), I came across this issue with the PCIe bus after finally being able to boot a persistent arch install on a USB stick.
I have tried the following things separate from each other as well as in certain combinations:

0. There is no BIOS update, even though this is likely a BIOS (or in this case EFI) issue, so I cannot do that.
1. tried adding

memmap=64M$0xe0000000

as kernel parameter
2. tried adding

pci=nocrs

as kernel parameter
3. tried adding

pci=realloc

as kernel parameter.
4. obviously tried to find a solution via arch forums, search engines and most importantly arch wiki

The issue itself seems to be very similar to this one, hence why i tried identical solutions and none of them worked.
In all cases, the error seems to persist and i do want to boot this thing with arch, so if any workaround could be found to make this work, that would be nice.
Below are things that I can think of as useful and have seen being asked for in forums.

Current kernel parameters

loglevel=3 rd.udev.log_level=3 splash nomodeset i915.modeset=0 fbcon=rotate:1 pci=realloc

Output for lspci -vvv

00:00.0 Host bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series SoC Transaction Register (rev 09)
	Subsystem: Acer Incorporated [ALI] Device 084c
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel driver in use: iosf_mbi_pci

00:02.0 VGA compatible controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Graphics & Display (rev 09) (prog-if 00 [VGA controller])
	Subsystem: Acer Incorporated [ALI] Device 084c
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 255
	Region 0: Memory at 90000000 (32-bit, non-prefetchable) [size=4M]
	Region 2: Memory at 80000000 (32-bit, prefetchable) [size=256M]
	Region 4: I/O ports at 1000 [size=8]
	Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [b0] Vendor Specific Information: Len=07 <?>
	Kernel modules: i915

00:14.0 USB controller: Intel Corporation Atom Processor Z36xxx/Z37xxx, Celeron N2000 Series USB xHCI (rev 09) (prog-if 30 [XHCI])
	Subsystem: Intel Corporation Atom Processor Z36xxx/Z37xxx, Celeron N2000 Series USB xHCI
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 34
	Region 0: Memory at 90800000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [70] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
		Address: 00000000fee08004  Data: 0023
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci

00:1a.0 Encryption controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Trusted Execution Engine (rev 09)
	Subsystem: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Trusted Execution Engine
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 47
	Region 0: Memory at 90700000 (32-bit, non-prefetchable) [size=1M]
	Region 1: Memory at 90600000 (32-bit, non-prefetchable) [size=1M]
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee04004  Data: 0026
	Kernel driver in use: mei_txe
	Kernel modules: mei_txe

00:1f.0 ISA bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Power Control Unit (rev 09)
	Subsystem: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Power Control Unit
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>
	Kernel driver in use: lpc_ich
	Kernel modules: lpc_ich

FULL Kernel Log

[    0.000000] Linux version 5.15.5-arch1-1 (linux@archlinux) (gcc (GCC) 11.1.0, GNU ld (GNU Binutils) 2.36.1) #1 SMP PREEMPT Thu, 25 Nov 2021 22:09:33 +0000
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=6444baed-0f35-4745-93f9-9f30584b8b0b rw loglevel=3 rd.udev.log_level=3 splash nomodeset i915.modeset=0 fbcon=rotate:1 pci=realloc
[    0.000000] x86/fpu: x87 FPU will use FXSAVE
[    0.000000] signal: max sigframe size: 1440
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009dfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000200fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020100000-0x00000000782bafff] usable
[    0.000000] BIOS-e820: [mem 0x00000000782bb000-0x00000000784bafff] type 20
[    0.000000] BIOS-e820: [mem 0x00000000784bb000-0x0000000078bbafff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000078bbb000-0x0000000078cbafff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000078cbb000-0x0000000078cfafff] ACPI data
[    0.000000] BIOS-e820: [mem 0x0000000078cfb000-0x000000007951bfff] usable
[    0.000000] BIOS-e820: [mem 0x000000007951c000-0x000000007951cfff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007951d000-0x0000000079526fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000079527000-0x0000000079e26fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000079e27000-0x0000000079ffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffd00000-0x00000000ffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.31 by INSYDE Corp.
[    0.000000] efi: ACPI 2.0=0x78cfa014 ESRT=0x78559e10 SMBIOS=0x78bba000 
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: Acer Iconia W4-820/Cheetah3, BIOS V1.16 03/13/2014
[    0.000000] tsc: Detected 1333.333 MHz processor
[    0.000030] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000045] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000068] last_pfn = 0x7a000 max_arch_pfn = 0x400000000
[    0.000138] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.010236] esrt: Reserving ESRT space from 0x0000000078559e10 to 0x0000000078559e48.
[    0.013218] Secure boot disabled
[    0.013223] RAMDISK: [mem 0x36719000-0x37383fff]
[    0.013244] ACPI: Early table checksum verification disabled
[    0.013254] ACPI: RSDP 0x0000000078CFA014 000024 (v02 ACRSYS)
[    0.013270] ACPI: XSDT 0x0000000078CD4188 0000DC (v01 ACRSYS ACRPRDCT 00000003      01000013)
[    0.013290] ACPI: FACP 0x0000000078CF0000 00010C (v05 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013312] ACPI: DSDT 0x0000000078CE0000 00B10F (v02 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013329] ACPI: UEFI 0x0000000078CF9000 000236 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.013344] ACPI: TCPA 0x0000000078CF8000 000032 (v02 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.013359] ACPI: MSDM 0x0000000078CF7000 000055 (v03 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.013374] ACPI: UEFI 0x0000000078CF6000 000042 (v01 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.013390] ACPI: SSDT 0x0000000078CF2000 00305D (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.013405] ACPI: DBG2 0x0000000078CF1000 000072 (v00 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013420] ACPI: HPET 0x0000000078CEF000 000038 (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013435] ACPI: LPIT 0x0000000078CEE000 000104 (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013450] ACPI: APIC 0x0000000078CED000 00006C (v03 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013464] ACPI: MCFG 0x0000000078CEC000 00003C (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013479] ACPI: SSDT 0x0000000078CDF000 0005F9 (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013494] ACPI: SSDT 0x0000000078CDD000 001C9F (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013509] ACPI: SSDT 0x0000000078CDC000 000058 (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013524] ACPI: SSDT 0x0000000078CDB000 0000FF (v01 ACRSYS ACRPRDCT 00000003 1025 00040000)
[    0.013539] ACPI: SSDT 0x0000000078CDA000 00043A (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
[    0.013554] ACPI: TPM2 0x0000000078CD9000 000034 (v03 ACRSYS ACRPRDCT 00000000 1025 00040000)
[    0.013569] ACPI: SSDT 0x0000000078CD8000 000763 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.013584] ACPI: SSDT 0x0000000078CD7000 000290 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.013599] ACPI: SSDT 0x0000000078CD6000 00017A (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
[    0.013614] ACPI: FPDT 0x0000000078CD5000 000044 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.013629] ACPI: CSRT 0x0000000078CD3000 00014C (v00 ACRSYS ACRPRDCT 00000005 1025 00040000)
[    0.013644] ACPI: BGRT 0x0000000078CD2000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
[    0.013657] ACPI: Reserving FACP table memory at [mem 0x78cf0000-0x78cf010b]
[    0.013664] ACPI: Reserving DSDT table memory at [mem 0x78ce0000-0x78ceb10e]
[    0.013669] ACPI: Reserving UEFI table memory at [mem 0x78cf9000-0x78cf9235]
[    0.013675] ACPI: Reserving TCPA table memory at [mem 0x78cf8000-0x78cf8031]
[    0.013680] ACPI: Reserving MSDM table memory at [mem 0x78cf7000-0x78cf7054]
[    0.013685] ACPI: Reserving UEFI table memory at [mem 0x78cf6000-0x78cf6041]
[    0.013690] ACPI: Reserving SSDT table memory at [mem 0x78cf2000-0x78cf505c]
[    0.013695] ACPI: Reserving DBG2 table memory at [mem 0x78cf1000-0x78cf1071]
[    0.013700] ACPI: Reserving HPET table memory at [mem 0x78cef000-0x78cef037]
[    0.013705] ACPI: Reserving LPIT table memory at [mem 0x78cee000-0x78cee103]
[    0.013710] ACPI: Reserving APIC table memory at [mem 0x78ced000-0x78ced06b]
[    0.013716] ACPI: Reserving MCFG table memory at [mem 0x78cec000-0x78cec03b]
[    0.013721] ACPI: Reserving SSDT table memory at [mem 0x78cdf000-0x78cdf5f8]
[    0.013726] ACPI: Reserving SSDT table memory at [mem 0x78cdd000-0x78cdec9e]
[    0.013731] ACPI: Reserving SSDT table memory at [mem 0x78cdc000-0x78cdc057]
[    0.013736] ACPI: Reserving SSDT table memory at [mem 0x78cdb000-0x78cdb0fe]
[    0.013741] ACPI: Reserving SSDT table memory at [mem 0x78cda000-0x78cda439]
[    0.013746] ACPI: Reserving TPM2 table memory at [mem 0x78cd9000-0x78cd9033]
[    0.013751] ACPI: Reserving SSDT table memory at [mem 0x78cd8000-0x78cd8762]
[    0.013757] ACPI: Reserving SSDT table memory at [mem 0x78cd7000-0x78cd728f]
[    0.013762] ACPI: Reserving SSDT table memory at [mem 0x78cd6000-0x78cd6179]
[    0.013767] ACPI: Reserving FPDT table memory at [mem 0x78cd5000-0x78cd5043]
[    0.013772] ACPI: Reserving CSRT table memory at [mem 0x78cd3000-0x78cd314b]
[    0.013778] ACPI: Reserving BGRT table memory at [mem 0x78cd2000-0x78cd2037]
[    0.013879] No NUMA configuration found
[    0.013884] Faking a node at [mem 0x0000000000000000-0x0000000079ffffff]
[    0.013899] NODE_DATA(0) allocated [mem 0x77feb000-0x77feefff]
[    0.013973] Zone ranges:
[    0.013977]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.013986]   DMA32    [mem 0x0000000001000000-0x0000000079ffffff]
[    0.013993]   Normal   empty
[    0.013998]   Device   empty
[    0.014003] Movable zone start for each node
[    0.014006] Early memory node ranges
[    0.014009]   node   0: [mem 0x0000000000001000-0x000000000008efff]
[    0.014015]   node   0: [mem 0x0000000000090000-0x000000000009dfff]
[    0.014020]   node   0: [mem 0x0000000000100000-0x000000001fffffff]
[    0.014025]   node   0: [mem 0x0000000020100000-0x00000000782bafff]
[    0.014031]   node   0: [mem 0x0000000078cfb000-0x000000007951bfff]
[    0.014036]   node   0: [mem 0x000000007951d000-0x0000000079526fff]
[    0.014041]   node   0: [mem 0x0000000079e27000-0x0000000079ffffff]
[    0.014047] Initmem setup node 0 [mem 0x0000000000001000-0x0000000079ffffff]
[    0.014062] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.014067] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.014150] On node 0, zone DMA: 98 pages in unavailable ranges
[    0.024484] On node 0, zone DMA32: 256 pages in unavailable ranges
[    0.024636] On node 0, zone DMA32: 2624 pages in unavailable ranges
[    0.024642] On node 0, zone DMA32: 1 pages in unavailable ranges
[    0.024748] On node 0, zone DMA32: 2304 pages in unavailable ranges
[    0.025672] On node 0, zone DMA32: 24576 pages in unavailable ranges
[    0.025683] x86/hpet: Will disable the HPET for this platform because it's not reliable
[    0.025693] Reserving Intel graphics memory at [mem 0x7af00000-0x7eefffff]
[    0.025797] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-86
[    0.025816] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.025824] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.025834] ACPI: Using ACPI (MADT) for SMP configuration information
[    0.025840] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.025870] e820: update [mem 0x7680b000-0x76883fff] usable ==> reserved
[    0.025903] TSC deadline timer available
[    0.025908] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.025989] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.026000] PM: hibernation: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[    0.026010] PM: hibernation: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[    0.026014] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.026023] PM: hibernation: Registered nosave memory: [mem 0x20000000-0x200fffff]
[    0.026031] PM: hibernation: Registered nosave memory: [mem 0x7680b000-0x76883fff]
[    0.026040] PM: hibernation: Registered nosave memory: [mem 0x782bb000-0x784bafff]
[    0.026045] PM: hibernation: Registered nosave memory: [mem 0x784bb000-0x78bbafff]
[    0.026049] PM: hibernation: Registered nosave memory: [mem 0x78bbb000-0x78cbafff]
[    0.026053] PM: hibernation: Registered nosave memory: [mem 0x78cbb000-0x78cfafff]
[    0.026062] PM: hibernation: Registered nosave memory: [mem 0x7951c000-0x7951cfff]
[    0.026071] PM: hibernation: Registered nosave memory: [mem 0x79527000-0x79e26fff]
[    0.026078] [mem 0x7ef00000-0xe00f7fff] available for PCI devices
[    0.026083] Booting paravirtualized kernel on bare hardware
[    0.026091] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[    0.039717] setup_percpu: NR_CPUS:320 nr_cpumask_bits:320 nr_cpu_ids:4 nr_node_ids:1
[    0.040684] percpu: Embedded 61 pages/cpu s212992 r8192 d28672 u524288
[    0.040718] pcpu-alloc: s212992 r8192 d28672 u524288 alloc=1*2097152
[    0.040730] pcpu-alloc: [0] 0 1 2 3 
[    0.040826] Built 1 zonelists, mobility grouping on.  Total pages: 486463
[    0.040835] Policy zone: DMA32
[    0.040840] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=6444baed-0f35-4745-93f9-9f30584b8b0b rw loglevel=3 rd.udev.log_level=3 splash nomodeset i915.modeset=0 fbcon=rotate:1 pci=realloc
[    0.041077] You have booted with nomodeset. This means your GPU drivers are DISABLED
[    0.041081] Any video related functionality will be severely degraded, and you may not even be able to suspend the system properly
[    0.041084] Unless you actually understand what nomodeset does, you should reboot without enabling it
[    0.041197] Unknown kernel command line parameters "splash BOOT_IMAGE=/vmlinuz-linux", will be passed to user space.
[    0.041857] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.042211] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.042998] mem auto-init: stack:byref_all(zero), heap alloc:on, heap free:off
[    0.059844] Memory: 1849692K/1977708K available (14344K kernel code, 2071K rwdata, 10788K rodata, 1860K init, 3844K bss, 127756K reserved, 0K cma-reserved)
[    0.059867] random: get_random_u64 called from __kmem_cache_create+0x2a/0x540 with crng_init=0
[    0.060495] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.060544] Kernel/User page tables isolation: enabled
[    0.060599] ftrace: allocating 44288 entries in 174 pages
[    0.097706] ftrace: allocated 173 pages with 5 groups
[    0.098056] rcu: Preemptible hierarchical RCU implementation.
[    0.098062] rcu: 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.098065] rcu: 	RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=4.
[    0.098070] rcu: 	RCU priority boosting: priority 1 delay 500 ms.
[    0.098074] 	Trampoline variant of Tasks RCU enabled.
[    0.098077] 	Rude variant of Tasks RCU enabled.
[    0.098079] 	Tracing variant of Tasks RCU enabled.
[    0.098082] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.098086] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.115108] NR_IRQS: 20736, nr_irqs: 1024, preallocated irqs: 0
[    0.115439] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[    0.115688] Console: colour dummy device 80x25
[    0.115743] printk: console [tty0] enabled
[    0.115816] ACPI: Core revision 20210730
[    0.116299] APIC: Switch to symmetric I/O mode setup
[    0.116363] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x13381e82524, max_idle_ns: 440795248224 ns
[    0.116381] Calibrating delay loop (skipped), value calculated using timer frequency.. 2667.77 BogoMIPS (lpj=4444443)
[    0.116392] pid_max: default: 32768 minimum: 301
[    0.119708] LSM: Security Framework initializing
[    0.119708] landlock: Up and running.
[    0.119708] Yama: becoming mindful.
[    0.119708] LSM support for eBPF active
[    0.119708] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.119708] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.119708] CPU0: Thermal monitoring enabled (TM1)
[    0.119708] process: using mwait in idle threads
[    0.119708] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[    0.119708] Last level dTLB entries: 4KB 128, 2MB 16, 4MB 16, 1GB 0
[    0.119708] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.119708] Spectre V2 : Mitigation: Full generic retpoline
[    0.119708] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.119708] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[    0.119708] Freeing SMP alternatives memory: 36K
[    0.119708] smpboot: Estimated ratio of average max frequency by base frequency (times 1024): 1433
[    0.119708] smpboot: CPU0: Intel(R) Atom(TM) CPU  Z3740  @ 1.33GHz (family: 0x6, model: 0x37, stepping: 0x3)
[    0.119708] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, 8-deep LBR, full-width counters, Intel PMU driver.
[    0.119708] ... version:                3
[    0.119708] ... bit width:              40
[    0.119708] ... generic registers:      2
[    0.119708] ... value mask:             000000ffffffffff
[    0.119708] ... max period:             0000007fffffffff
[    0.119708] ... fixed-purpose events:   3
[    0.119708] ... event mask:             0000000700000003
[    0.119708] rcu: Hierarchical SRCU implementation.
[    0.119708] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.120015] smp: Bringing up secondary CPUs ...
[    0.120708] x86: Booting SMP configuration:
[    0.120716] .... node  #0, CPUs:      #1 #2 #3
[    0.132144] smp: Brought up 1 node, 4 CPUs
[    0.132144] smpboot: Max logical packages: 1
[    0.132144] smpboot: Total of 4 processors activated (10670.10 BogoMIPS)
[    0.133401] devtmpfs: initialized
[    0.133401] x86/mm: Memory block size: 128MB
[    0.134162] ACPI: PM: Registering ACPI NVS region [mem 0x0008f000-0x0008ffff] (4096 bytes)
[    0.134162] ACPI: PM: Registering ACPI NVS region [mem 0x78bbb000-0x78cbafff] (1048576 bytes)
[    0.134162] ACPI: PM: Registering ACPI NVS region [mem 0x79527000-0x79e26fff] (9437184 bytes)
[    0.134162] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.134162] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.134162] pinctrl core: initialized pinctrl subsystem
[    0.136518] PM: RTC time: 15:17:11, date: 2021-11-28
[    0.136973] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.137332] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.137433] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.137526] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.137582] audit: initializing netlink subsys (disabled)
[    0.137638] audit: type=2000 audit(1638112631.019:1): state=initialized audit_enabled=0 res=1
[    0.137638] thermal_sys: Registered thermal governor 'fair_share'
[    0.137638] thermal_sys: Registered thermal governor 'bang_bang'
[    0.137638] thermal_sys: Registered thermal governor 'step_wise'
[    0.137638] thermal_sys: Registered thermal governor 'user_space'
[    0.137638] thermal_sys: Registered thermal governor 'power_allocator'
[    0.137638] cpuidle: using governor ladder
[    0.137638] cpuidle: using governor menu
[    0.137638] ACPI: bus type PCI registered
[    0.137638] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.137638] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[    0.137638] PCI: not using MMCONFIG
[    0.137638] PCI: Using configuration type 1 for base access
[    0.138098] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.144822] Kprobes globally optimized
[    0.144847] HugeTLB: can free 6 vmemmap pages for hugepages-2048kB
[    0.144847] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.150143] ACPI: Added _OSI(Module Device)
[    0.150152] ACPI: Added _OSI(Processor Device)
[    0.150156] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.150160] ACPI: Added _OSI(Processor Aggregator Device)
[    0.150165] ACPI: Added _OSI(Linux-Dell-Video)
[    0.150169] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.150173] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.201995] ACPI: 10 ACPI AML tables successfully acquired and loaded
[    0.211976] ACPI: Dynamic OEM Table Load:
[    0.212007] ACPI: SSDT 0xFFFF959141177000 000353 (v01 PmRef  Cpu0Ist  00003000 INTL 20121114)
[    0.215365] ACPI: Dynamic OEM Table Load:
[    0.215391] ACPI: SSDT 0xFFFF9591B9F59000 000433 (v01 PmRef  Cpu0Cst  00003001 INTL 20121114)
[    0.219779] ACPI: Dynamic OEM Table Load:
[    0.219805] ACPI: SSDT 0xFFFF959141113C00 00015F (v01 PmRef  ApIst    00003000 INTL 20121114)
[    0.222539] ACPI: Dynamic OEM Table Load:
[    0.222562] ACPI: SSDT 0xFFFF95914193CE40 00008D (v01 PmRef  ApCst    00003000 INTL 20121114)
[    0.231011] ACPI: Interpreter enabled
[    0.231058] ACPI: PM: (supports S0)
[    0.231065] ACPI: Using IOAPIC for interrupt routing
[    0.231206] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[    0.240848] [Firmware Info]: PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] not reserved in ACPI motherboard resources
[    0.240859] PCI: not using MMCONFIG
[    0.240870] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.248071] ACPI: PM: Power Resource [USBC]
[    0.249063] ACPI: PM: Power Resource [WWPR]
[    0.271441] ACPI: PM: Power Resource [CLK0]
[    0.271826] ACPI: PM: Power Resource [P28X]
[    0.271932] ACPI: PM: Power Resource [P18X]
[    0.272957] ACPI: PM: Power Resource [CLK1]
[    0.275440] ACPI: PM: Power Resource [TCPR]
[    0.283010] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.283038] acpi PNP0A08:00: _OSC: OS supports [ASPM ClockPM Segments MSI EDR HPX-Type3]
[    0.283317] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_ERROR)
[    0.283362] acpi PNP0A08:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[    0.284828] PCI host bridge to bus 0000:00
[    0.284838] pci_bus 0000:00: root bus resource [io  0x0070-0x0077]
[    0.284847] pci_bus 0000:00: root bus resource [io  0x0000-0x006f window]
[    0.284855] pci_bus 0000:00: root bus resource [io  0x0078-0x0cf7 window]
[    0.284862] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.284868] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.284875] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[    0.284882] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff window]
[    0.284888] pci_bus 0000:00: root bus resource [mem 0x90c00000-0x90ffffff window]
[    0.284895] pci_bus 0000:00: root bus resource [mem 0x7af00001-0x7ef00000 window]
[    0.284902] pci_bus 0000:00: root bus resource [mem 0x80000000-0x908ffffe window]
[    0.284908] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed40fff window]
[    0.284915] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.285085] pci 0000:00:00.0: [8086:0f00] type 00 class 0x060000
[    0.285518] pci 0000:00:02.0: [8086:0f31] type 00 class 0x030000
[    0.285540] pci 0000:00:02.0: reg 0x10: [mem 0x90000000-0x903fffff]
[    0.285559] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff pref]
[    0.285577] pci 0000:00:02.0: reg 0x20: [io  0x1000-0x1007]
[    0.285611] pci 0000:00:02.0: BAR 2: assigned to efifb
[    0.286030] pci 0000:00:14.0: [8086:0f35] type 00 class 0x0c0330
[    0.286058] pci 0000:00:14.0: reg 0x10: [mem 0x90800000-0x9080ffff 64bit]
[    0.286145] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.286567] pci 0000:00:1a.0: [8086:0f18] type 00 class 0x108000
[    0.286596] pci 0000:00:1a.0: reg 0x10: [mem 0x90700000-0x907fffff]
[    0.286614] pci 0000:00:1a.0: reg 0x14: [mem 0x90600000-0x906fffff]
[    0.286719] pci 0000:00:1a.0: PME# supported from D0 D3hot
[    0.287104] pci 0000:00:1f.0: [8086:0f1c] type 00 class 0x060100
[    0.289353] ACPI: PCI: Interrupt link LNKA configured for IRQ 0
[    0.289361] ACPI: PCI: Interrupt link LNKA disabled
[    0.289764] ACPI: PCI: Interrupt link LNKB configured for IRQ 0
[    0.289772] ACPI: PCI: Interrupt link LNKB disabled
[    0.290171] ACPI: PCI: Interrupt link LNKC configured for IRQ 0
[    0.290179] ACPI: PCI: Interrupt link LNKC disabled
[    0.290577] ACPI: PCI: Interrupt link LNKD configured for IRQ 0
[    0.290585] ACPI: PCI: Interrupt link LNKD disabled
[    0.290982] ACPI: PCI: Interrupt link LNKE configured for IRQ 0
[    0.290989] ACPI: PCI: Interrupt link LNKE disabled
[    0.291387] ACPI: PCI: Interrupt link LNKF configured for IRQ 0
[    0.291394] ACPI: PCI: Interrupt link LNKF disabled
[    0.291793] ACPI: PCI: Interrupt link LNKG configured for IRQ 0
[    0.291800] ACPI: PCI: Interrupt link LNKG disabled
[    0.292197] ACPI: PCI: Interrupt link LNKH configured for IRQ 0
[    0.292205] ACPI: PCI: Interrupt link LNKH disabled
[    0.312851] ACPI: PM: Power Resource [PLPE]
[    0.330765] iommu: Default domain type: Translated 
[    0.330776] iommu: DMA domain TLB invalidation policy: lazy mode 
[    0.330832] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.330832] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.330832] pci 0000:00:02.0: vgaarb: bridge control possible
[    0.330832] vgaarb: loaded
[    0.330832] SCSI subsystem initialized
[    0.330832] libata version 3.00 loaded.
[    0.330832] ACPI: bus type USB registered
[    0.330832] usbcore: registered new interface driver usbfs
[    0.330832] usbcore: registered new interface driver hub
[    0.330832] usbcore: registered new device driver usb
[    0.564712] pps_core: LinuxPPS API ver. 1 registered
[    0.564722] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.564737] PTP clock support registered
[    0.564772] EDAC MC: Ver: 3.0.0
[    0.564888] Registered efivars operations
[    0.564888] NetLabel: Initializing
[    0.564888] NetLabel:  domain hash size = 128
[    0.564888] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.564888] NetLabel:  unlabeled traffic allowed by default
[    0.564888] PCI: Using ACPI for IRQ routing
[    0.564888] PCI: pci_cache_line_size set to 64 bytes
[    0.564888] Expanded resource Reserved due to conflict with PCI Bus 0000:00
[    0.564888] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
[    0.564888] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[    0.564888] e820: reserve RAM buffer [mem 0x7680b000-0x77ffffff]
[    0.564888] e820: reserve RAM buffer [mem 0x782bb000-0x7bffffff]
[    0.564888] e820: reserve RAM buffer [mem 0x7951c000-0x7bffffff]
[    0.564888] e820: reserve RAM buffer [mem 0x79527000-0x7bffffff]
[    0.564888] e820: reserve RAM buffer [mem 0x7a000000-0x7bffffff]
[    0.569813] clocksource: Switched to clocksource tsc-early
[    0.604160] VFS: Disk quotas dquot_6.6.0
[    0.604214] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.604518] pnp: PnP ACPI init
[    0.604936] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.604950] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.604958] system 00:01: [io  0x0500-0x05fe] has been reserved
[    0.604965] system 00:01: [io  0x0600-0x061f] has been reserved
[    0.604972] system 00:01: [io  0x164e-0x164f] has been reserved
[    0.611327] pnp: PnP ACPI: found 2 devices
[    0.618065] NET: Registered PF_INET protocol family
[    0.618215] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.620083] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[    0.620162] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.620370] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[    0.620493] TCP: Hash tables configured (established 16384 bind 16384)
[    0.620694] MPTCP token hash table entries: 2048 (order: 3, 49152 bytes, linear)
[    0.620760] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.620802] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.620954] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.620980] NET: Registered PF_XDP protocol family
[    0.620994] pci_bus 0000:00: max bus depth: 0 pci_try_num: 1
[    0.621009] pci_bus 0000:00: resource 4 [io  0x0070-0x0077]
[    0.621018] pci_bus 0000:00: resource 5 [io  0x0000-0x006f window]
[    0.621025] pci_bus 0000:00: resource 6 [io  0x0078-0x0cf7 window]
[    0.621032] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff window]
[    0.621038] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[    0.621046] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[    0.621052] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000fffff window]
[    0.621059] pci_bus 0000:00: resource 11 [mem 0x90c00000-0x90ffffff window]
[    0.621066] pci_bus 0000:00: resource 12 [mem 0x7af00001-0x7ef00000 window]
[    0.621073] pci_bus 0000:00: resource 13 [mem 0x80000000-0x908ffffe window]
[    0.621080] pci_bus 0000:00: resource 14 [mem 0xfed40000-0xfed40fff window]
[    0.621286] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.621833] PCI: CLS 0 bytes, default 64
[    0.622029] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x13381e82524, max_idle_ns: 440795248224 ns
[    0.622061] Trying to unpack rootfs image as initramfs...
[    0.622112] clocksource: Switched to clocksource tsc
[    0.634919] Initialise system trusted keyrings
[    0.634957] Key type blacklist registered
[    0.635118] workingset: timestamp_bits=41 max_order=19 bucket_order=0
[    0.639746] zbud: loaded
[    0.664778] Key type asymmetric registered
[    0.664787] Asymmetric key parser 'x509' registered
[    0.664859] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    0.664995] io scheduler mq-deadline registered
[    0.665002] io scheduler kyber registered
[    0.665131] io scheduler bfq registered
[    0.665928] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.668016] ACPI: AC: AC Adapter [ADP1] (off-line)
[    0.668228] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    0.668301] ACPI: button: Lid Switch [LID]
[    0.675886] ACPI: thermal: [Firmware Bug]: No valid trip found
[    0.676847] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.689252] hpet: number irqs doesn't agree with number of timers
[    0.689447] Non-volatile memory driver v1.3
[    0.689452] Linux agpgart interface v0.103
[    0.689457] AMD-Vi: AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[    0.689460] AMD-Vi: AMD IOMMUv2 functionality not available on this system
[    0.694853] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.694874] ehci-pci: EHCI PCI platform driver
[    0.694910] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.694921] ohci-pci: OHCI PCI platform driver
[    0.694946] uhci_hcd: USB Universal Host Controller Interface driver
[    0.695068] usbcore: registered new interface driver usbserial_generic
[    0.695089] usbserial: USB Serial support registered for generic
[    0.695616] rtc_cmos 00:00: registered as rtc0
[    0.695659] rtc_cmos 00:00: setting system clock to 2021-11-28T15:17:11 UTC (1638112631)
[    0.695718] rtc_cmos 00:00: no alarms, 242 bytes nvram
[    0.696412] intel_pstate: Intel P-state driver initializing
[    0.698058] ledtrig-cpu: registered to indicate activity on CPUs
[    0.698368] efifb: probing for efifb
[    0.698404] efifb: framebuffer at 0x80000000, using 4032k, total 4032k
[    0.698410] efifb: mode is 800x1280x32, linelength=3200, pages=1
[    0.698413] efifb: scrolling: redraw
[    0.698415] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.698665] fbcon: Deferring console take-over
[    0.698669] fb0: EFI VGA frame buffer device
[    0.698745] hid: raw HID events driver (C) Jiri Kosina
[    0.699129] drop_monitor: Initializing network drop monitor service
[    0.699263] Initializing XFRM netlink socket
[    0.699518] NET: Registered PF_INET6 protocol family
[    0.722127] ACPI: battery: Slot [BATC] (battery present)
[    0.798420] Freeing initrd memory: 12716K
[    0.829703] Segment Routing with IPv6
[    0.829855] RPL Segment Routing with IPv6
[    0.829926] In-situ OAM (IOAM) with IPv6
[    0.829999] NET: Registered PF_PACKET protocol family
[    0.834917] microcode: sig=0x30673, pf=0x2, revision=0x322
[    0.835582] microcode: Microcode Update Driver: v2.2.
[    0.835598] IPI shorthand broadcast: enabled
[    0.835634] sched_clock: Marking stable (833184324, 1118910)->(849560575, -15257341)
[    0.838100] registered taskstats version 1
[    0.840911] Loading compiled-in X.509 certificates
[    0.876105] Loaded X.509 cert 'Build time autogenerated kernel key: f73733dc3330ff91e25adb9d4aec12785405b2b4'
[    0.879830] zswap: loaded using pool lz4/z3fold
[    0.885294] Key type ._fscrypt registered
[    0.885314] Key type .fscrypt registered
[    0.885323] Key type fscrypt-provisioning registered
[    0.889435] PM:   Magic number: 13:446:286
[    0.891425] RAS: Correctable Errors collector initialized.
[    0.927477] Freeing unused decrypted memory: 2036K
[    0.929824] Freeing unused kernel image (initmem) memory: 1860K
[    0.930605] Write protecting the kernel read-only data: 28672k
[    0.934706] Freeing unused kernel image (text/rodata gap) memory: 2036K
[    0.937199] Freeing unused kernel image (rodata/data gap) memory: 1500K
[    1.036163] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    1.036176] rodata_test: all tests were successful
[    1.036819] x86/mm: Checking user space page tables
[    1.119845] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    1.119894] Run /init as init process
[    1.119898]   with arguments:
[    1.119901]     /init
[    1.119904]     splash
[    1.119906]   with environment:
[    1.119908]     HOME=/
[    1.119910]     TERM=linux
[    1.119912]     BOOT_IMAGE=/vmlinuz-linux
[    1.171595] fbcon: Taking over console
[    1.172025] Console: switching to colour frame buffer device 160x50
[    1.565618] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.565641] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    1.566749] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810
[    1.567119] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[    1.567128] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.567132] usb usb1: Product: xHCI Host Controller
[    1.567136] usb usb1: Manufacturer: Linux 5.15.5-arch1-1 xhci-hcd
[    1.567140] usb usb1: SerialNumber: 0000:00:14.0
[    1.567543] hub 1-0:1.0: USB hub found
[    1.567574] hub 1-0:1.0: 6 ports detected
[    2.087674] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    2.087700] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    2.087714] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[    2.088136] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15
[    2.088150] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.088156] usb usb2: Product: xHCI Host Controller
[    2.088162] usb usb2: Manufacturer: Linux 5.15.5-arch1-1 xhci-hcd
[    2.088167] usb usb2: SerialNumber: 0000:00:14.0
[    2.088895] hub 2-0:1.0: USB hub found
[    2.088944] hub 2-0:1.0: 1 port detected
[    2.336888] usb 1-2: new high-speed USB device number 2 using xhci_hcd
[    2.481166] usb 1-2: New USB device found, idVendor=2109, idProduct=2812, bcdDevice=90.90
[    2.481190] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.481201] usb 1-2: Product: USB2.0 Hub             
[    2.481210] usb 1-2: Manufacturer: VIA Labs, Inc.         
[    2.484232] hub 1-2:1.0: USB hub found
[    2.484895] hub 1-2:1.0: 4 ports detected
[    2.796919] usb 1-2.3: new high-speed USB device number 3 using xhci_hcd
[    2.913271] usb 1-2.3: New USB device found, idVendor=05e3, idProduct=0749, bcdDevice=15.35
[    2.913305] usb 1-2.3: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    2.913323] usb 1-2.3: Product: USB3.0 Card Reader
[    2.913336] usb 1-2.3: Manufacturer: Generic
[    2.913348] usb 1-2.3: SerialNumber: 000000001536
[    2.947575] usb-storage 1-2.3:1.0: USB Mass Storage device detected
[    2.949771] scsi host0: usb-storage 1-2.3:1.0
[    2.950026] usbcore: registered new interface driver usb-storage
[    2.967098] usbcore: registered new interface driver uas
[    3.007115] usb 1-2.4: new full-speed USB device number 4 using xhci_hcd
[    3.121955] usb 1-2.4: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=12.01
[    3.121989] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.122007] usb 1-2.4: Product: USB Receiver
[    3.122020] usb 1-2.4: Manufacturer: Logitech
[    3.170451] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.4/1-2.4:1.0/0003:046D:C52B.0001/input/input1
[    3.228455] hid-generic 0003:046D:C52B.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:14.0-2.4/input0
[    3.234033] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.4/1-2.4:1.1/0003:046D:C52B.0002/input/input2
[    3.234810] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.4/1-2.4:1.1/0003:046D:C52B.0002/input/input3
[    3.290855] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.4/1-2.4:1.1/0003:046D:C52B.0002/input/input4
[    3.292693] hid-generic 0003:046D:C52B.0002: input,hiddev96,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-2.4/input1
[    3.298049] hid-generic 0003:046D:C52B.0003: hiddev97,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2.4/input2
[    3.298288] usbcore: registered new interface driver usbhid
[    3.298304] usbhid: USB HID core driver
[    3.958346] scsi 0:0:0:0: Direct-Access     Generic  MassStorageClass 1536 PQ: 0 ANSI: 6
[    3.960590] scsi 0:0:0:1: Direct-Access     Generic  MassStorageClass 1536 PQ: 0 ANSI: 6
[    3.964766] sd 0:0:0:0: [sda] Media removed, stopped polling
[    4.168797] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    4.174416] random: fast init done
[    4.177217] sd 0:0:0:1: [sdb] 7626752 512-byte logical blocks: (3.90 GB/3.64 GiB)
[    4.179044] sd 0:0:0:1: [sdb] Write Protect is off
[    4.179064] sd 0:0:0:1: [sdb] Mode Sense: 21 00 00 00
[    4.180715] sd 0:0:0:1: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    4.263932]  sdb: sdb1 sdb2
[    4.272855] sd 0:0:0:1: [sdb] Attached SCSI removable disk
[    6.372214] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[    7.958820] systemd[1]: systemd 249.7-1-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[    7.977136] systemd[1]: Detected architecture x86-64.
[    8.010476] systemd[1]: Hostname set to <test>.
[    9.314638] random: lvmconfig: uninitialized urandom read (4 bytes read)
[    9.670180] random: crng init done
[   10.452566] systemd[1]: Queued start job for default target Graphical Interface.
[   10.460902] systemd[1]: Created slice Slice /system/getty.
[   10.463755] systemd[1]: Created slice Slice /system/modprobe.
[   10.466350] systemd[1]: Created slice Slice /system/systemd-fsck.
[   10.468248] systemd[1]: Created slice User and Session Slice.
[   10.469021] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[   10.469771] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   10.471012] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   10.471600] systemd[1]: Reached target Local Encrypted Volumes.
[   10.472108] systemd[1]: Reached target Path Units.
[   10.472470] systemd[1]: Reached target Remote File Systems.
[   10.472837] systemd[1]: Reached target Slice Units.
[   10.473274] systemd[1]: Reached target Swaps.
[   10.473643] systemd[1]: Reached target Local Verity Protected Volumes.
[   10.474385] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[   10.475306] systemd[1]: Listening on LVM2 poll daemon socket.
[   10.484141] systemd[1]: Listening on Process Core Dump Socket.
[   10.485342] systemd[1]: Listening on Journal Audit Socket.
[   10.486178] systemd[1]: Listening on Journal Socket (/dev/log).
[   10.487062] systemd[1]: Listening on Journal Socket.
[   10.487694] systemd[1]: Listening on udev Control Socket.
[   10.488151] systemd[1]: Listening on udev Kernel Socket.
[   10.491274] systemd[1]: Mounting Huge Pages File System...
[   10.494252] systemd[1]: Mounting POSIX Message Queue File System...
[   10.497353] systemd[1]: Mounting Kernel Debug File System...
[   10.500345] systemd[1]: Mounting Kernel Trace File System...
[   10.506129] systemd[1]: Mounting Temporary Directory /tmp...
[   10.509627] systemd[1]: Starting Create List of Static Device Nodes...
[   10.512733] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[   10.516057] systemd[1]: Starting Load Kernel Module configfs...
[   10.519386] systemd[1]: Starting Load Kernel Module drm...
[   10.522751] systemd[1]: Starting Load Kernel Module fuse...
[   10.532612] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   10.532767] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   10.537909] systemd[1]: Starting Journal Service...
[   10.549021] systemd[1]: Starting Load Kernel Modules...
[   10.552106] systemd[1]: Starting Remount Root and Kernel File Systems...
[   10.552629] systemd[1]: Condition check resulted in Repartition Root Disk being skipped.
[   10.555480] systemd[1]: Starting Coldplug All udev Devices...
[   10.561998] systemd[1]: Mounted Huge Pages File System.
[   10.562641] systemd[1]: Mounted POSIX Message Queue File System.
[   10.563285] systemd[1]: Mounted Kernel Debug File System.
[   10.563835] systemd[1]: Mounted Kernel Trace File System.
[   10.566294] systemd[1]: Mounted Temporary Directory /tmp.
[   10.569612] systemd[1]: Finished Create List of Static Device Nodes.
[   10.572904] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[   10.573732] systemd[1]: Finished Load Kernel Module configfs.
[   10.577495] systemd[1]: modprobe@drm.service: Deactivated successfully.
[   10.578241] systemd[1]: Finished Load Kernel Module drm.
[   10.583183] fuse: init (API version 7.34)
[   10.583520] systemd[1]: Mounting Kernel Configuration File System...
[   10.586967] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[   10.587698] systemd[1]: Finished Load Kernel Module fuse.
[   10.591576] systemd[1]: Mounted Kernel Configuration File System.
[   10.596775] systemd[1]: Mounting FUSE Control File System...
[   10.602195] EXT4-fs (sdb2): re-mounted. Opts: (null). Quota mode: none.
[   10.605097] systemd[1]: Finished Remount Root and Kernel File Systems.
[   10.607857] systemd[1]: Mounted FUSE Control File System.
[   10.610145] systemd[1]: Condition check resulted in First Boot Wizard being skipped.
[   10.652721] Asymmetric key parser 'pkcs8' registered
[   10.657468] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   10.662290] systemd[1]: Starting Load/Save Random Seed...
[   10.664668] systemd[1]: Condition check resulted in Create System Users being skipped.
[   10.667779] systemd[1]: Starting Create Static Device Nodes in /dev...
[   10.671870] systemd[1]: Finished Load Kernel Modules.
[   10.674139] audit: type=1130 audit(1638112641.476:2): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-modules-load comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   10.677078] systemd[1]: Starting Apply Kernel Variables...
[   10.717206] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling.
[   10.719535] audit: type=1130 audit(1638112641.520:3): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=lvm2-monitor comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   10.751446] systemd[1]: Started Journal Service.
[   10.753815] audit: type=1130 audit(1638112641.556:4): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journald comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   10.984887] audit: type=1130 audit(1638112641.786:5): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udev-trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   11.435575] audit: type=1130 audit(1638112642.236:6): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-random-seed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   11.441082] systemd-journald[237]: Received client request to flush runtime journal.
[   11.445726] audit: type=1130 audit(1638112642.246:7): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-sysctl comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   12.443952] audit: type=1130 audit(1638112643.246:8): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup-dev comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   12.460936] audit: type=1334 audit(1638112643.263:9): prog-id=14 op=LOAD
[   12.462697] audit: type=1334 audit(1638112643.263:10): prog-id=15 op=LOAD
[   12.463833] audit: type=1334 audit(1638112643.266:11): prog-id=16 op=LOAD
[   14.593523] dw_dmac INTL9C60:00: DesignWare DMA Controller, 8 channels
[   14.630172] dw_dmac INTL9C60:01: DesignWare DMA Controller, 8 channels
[   14.656773] 80860F0A:00: ttyS4 at MMIO 0x9094d000 (irq = 8, base_baud = 2764800) is a 16550A
[   14.658816] serial serial0: tty port ttyS4 registered
[   14.710209] sdhci: Secure Digital Host Controller Interface driver
[   14.710218] sdhci: Copyright(c) Pierre Ossman
[   14.812719] mmc1: SDHCI controller on ACPI [80860F14:00] using ADMA
[   14.812951] mmc0: SDHCI controller on ACPI [80860F14:01] using ADMA
[   14.913861] mmc1: new HS200 MMC card at address 0001
[   15.000611] mmc2: SDHCI controller on ACPI [INT33BB:00] using ADMA
[   15.131151] mmc2: new ultra high speed DDR50 SDIO card at address 0001
[   15.604467] mc: Linux media interface: v0.10
[   15.733473] videodev: Linux video capture interface: v2.00
[   15.749497] Bluetooth: Core ver 2.22
[   15.749563] NET: Registered PF_BLUETOOTH protocol family
[   15.749567] Bluetooth: HCI device and connection manager initialized
[   15.749578] Bluetooth: HCI socket layer initialized
[   15.749583] Bluetooth: L2CAP socket layer initialized
[   15.749597] Bluetooth: SCO socket layer initialized
[   15.798700] atomisp_gmin_platform: module is from the staging directory, the quality is unknown, you have been warned.
[   15.799032] atomisp_gmin_platform: module is from the staging directory, the quality is unknown, you have been warned.
[   15.829234] input: SYNA7300:00 06CB:0106 Touchscreen as /devices/platform/80860F41:05/i2c-5/i2c-SYNA7300:00/0018:06CB:0106.0004/input/input6
[   15.829480] hid-generic 0018:06CB:0106.0004: input,hidraw3: I2C HID v1.00 Device [SYNA7300:00 06CB:0106] on i2c-SYNA7300:00
[   15.902857] atomisp_ov2722: module is from the staging directory, the quality is unknown, you have been warned.
[   15.903424] hid-generic 0018:0483:91D1.0005: hidraw4: I2C HID v1.00 Device [SMO91D0:00 0483:91D1] on i2c-SMO91D0:00
[   15.924324] atomisp_ov5693: module is from the staging directory, the quality is unknown, you have been warned.
[   15.976618] ov2722 i2c-INT33FB:00: gmin: power management provided via Crystal Cove PMIC (i2c addr 0x6e)
[   15.976630] ov2722 i2c-INT33FB:00: gmin_subdev_add: ACPI path is \_SB.I2C4.CAM2
[   15.977115] ov2722 i2c-INT33FB:00: Failed to find EFI variable INT33FB:00_ClkSrc
[   15.977129] ov2722 i2c-INT33FB:00: ClkSrc: using default (1)
[   15.977587] ov2722 i2c-INT33FB:00: Failed to find EFI variable INT33FB:00_CsiPort
[   15.977600] ov2722 i2c-INT33FB:00: CsiPort: using default (0)
[   15.978055] ov2722 i2c-INT33FB:00: Failed to find EFI variable INT33FB:00_CsiLanes
[   15.978068] ov2722 i2c-INT33FB:00: CsiLanes: using default (1)
[   15.978293] ov2722 i2c-INT33FB:00: will handle gpio0 via ACPI
[   15.978388] ov2722 i2c-INT33FB:00: will handle gpio1 via ACPI
[   15.978472] ov2722 i2c-INT33FB:00: Failed to find EFI gmin variable gmin_V1P8GPIO
[   15.978485] ov2722 i2c-INT33FB:00: V1P8GPIO: using default (-1)
[   15.978563] ov2722 i2c-INT33FB:00: Failed to find EFI gmin variable gmin_V2P8GPIO
[   15.978576] ov2722 i2c-INT33FB:00: V2P8GPIO: using default (-1)
[   15.978642] ov2722 i2c-INT33FB:00: Will use CLK1 (pmc_plt_clk_1)
[   15.978667] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.978671] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x57 value 0x63 mask 0xff
[   15.978677] ov2722 i2c-INT33FB:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.978682] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.978684] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x57 value 0x62 mask 0xff
[   15.978688] ov2722 i2c-INT33FB:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.978692] ov2722 i2c-INT33FB:00: sensor power-up failed
[   15.978696] ov2722 i2c-INT33FB:00: ov2722 power-up err.
[   15.978703] ov2722 i2c-INT33FB:00: sensor power-gating failed
[   15.981001] ov5693 i2c-INT33BE:00: Failed to find EFI variable INT33BE:00_I2CAddr
[   15.981016] ov5693 i2c-INT33BE:00: I2CAddr: using default (-1)
[   15.981027] ov5693 i2c-INT33BE:00: gmin: power management provided via Crystal Cove PMIC (i2c addr 0x6e)
[   15.981033] ov5693 i2c-INT33BE:00: gmin_subdev_add: ACPI path is \_SB.I2C3.CAM0
[   15.981506] ov5693 i2c-INT33BE:00: Failed to find EFI variable INT33BE:00_ClkSrc
[   15.981519] ov5693 i2c-INT33BE:00: ClkSrc: using default (1)
[   15.981969] ov5693 i2c-INT33BE:00: Failed to find EFI variable INT33BE:00_CsiPort
[   15.981983] ov5693 i2c-INT33BE:00: CsiPort: using default (0)
[   15.982568] ov5693 i2c-INT33BE:00: Failed to find EFI variable INT33BE:00_CsiLanes
[   15.982580] ov5693 i2c-INT33BE:00: CsiLanes: using default (1)
[   15.982755] ov5693 i2c-INT33BE:00: will handle gpio0 via ACPI
[   15.982918] ov5693 i2c-INT33BE:00: Failed to find EFI gmin variable gmin_V1P8GPIO
[   15.982932] ov5693 i2c-INT33BE:00: V1P8GPIO: using default (-1)
[   15.983023] ov5693 i2c-INT33BE:00: Failed to find EFI gmin variable gmin_V2P8GPIO
[   15.983036] ov5693 i2c-INT33BE:00: V2P8GPIO: using default (-1)
[   15.983139] ov5693 i2c-INT33BE:00: Will use CLK0 (pmc_plt_clk_0)
[   15.983162] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.983166] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x5d value 0x63 mask 0xff
[   15.983172] ov5693 i2c-INT33BE:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.983177] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.983179] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x5d value 0x62 mask 0xff
[   15.983183] ov5693 i2c-INT33BE:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.983187] ov5693 i2c-INT33BE:00: sensor power-up failed
[   15.983192] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.983195] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x5d value 0x63 mask 0xff
[   15.983199] ov5693 i2c-INT33BE:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.983203] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.983205] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x5d value 0x62 mask 0xff
[   15.983209] ov5693 i2c-INT33BE:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.983213] ov5693 i2c-INT33BE:00: sensor power-up failed
[   15.983218] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.983220] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x5d value 0x63 mask 0xff
[   15.983224] ov5693 i2c-INT33BE:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.983228] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.983230] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x5d value 0x62 mask 0xff
[   15.983235] ov5693 i2c-INT33BE:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.983239] ov5693 i2c-INT33BE:00: sensor power-up failed
[   15.983243] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.983245] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x5d value 0x63 mask 0xff
[   15.983250] ov5693 i2c-INT33BE:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.983254] intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
[   15.983256] intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x6e reg-addr 0x5d value 0x62 mask 0xff
[   15.983260] ov5693 i2c-INT33BE:00: ACPI didn't mapped the OpRegion needed to access I2C address 0x6e.
               Need to compile the kernel using CONFIG_*_PMIC_OPREGION settings
[   15.983264] ov5693 i2c-INT33BE:00: sensor power-up failed
[   15.983270] ov5693 i2c-INT33BE:00: ov5693 power-up err.
[   15.983275] ov5693 i2c-INT33BE:00: sensor power-gating failed
[   15.983504] ov2722: probe of i2c-INT33FB:00 failed with error -95
[   15.994024] ov5693: probe of i2c-INT33BE:00 failed with error -95
[   16.110016] Bluetooth: HCI UART driver ver 2.3
[   16.110028] Bluetooth: HCI UART protocol H4 registered
[   16.110032] Bluetooth: HCI UART protocol BCSP registered
[   16.110072] Bluetooth: HCI UART protocol LL registered
[   16.110076] Bluetooth: HCI UART protocol ATH3K registered
[   16.110102] Bluetooth: HCI UART protocol Three-wire (H5) registered
[   16.110212] Bluetooth: HCI UART protocol Intel registered
[   16.110370] Bluetooth: HCI UART protocol Broadcom registered
[   16.110396] Bluetooth: HCI UART protocol QCA registered
[   16.110400] Bluetooth: HCI UART protocol AG6XX registered
[   16.110424] Bluetooth: HCI UART protocol Marvell registered
[   16.130107] hci_uart_bcm serial0-0: ACPI Interrupt resource is active-high, this is usually wrong, treating the IRQ as active-low
[   16.130553] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator
[   16.130664] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator
[   16.228097] intel_sst_acpi 80860F28:00: BYT-CR not detected
[   16.228281] intel_sst_acpi 80860F28:00: LPE base: 0x90a00000 size:0x200000
[   16.228288] intel_sst_acpi 80860F28:00: IRAM base: 0x90ac0000
[   16.228325] intel_sst_acpi 80860F28:00: DRAM base: 0x90b00000
[   16.228338] intel_sst_acpi 80860F28:00: SHIM base: 0x90b40000
[   16.228350] intel_sst_acpi 80860F28:00: Mailbox base: 0x90b44000
[   16.228362] intel_sst_acpi 80860F28:00: DDR base: 0x20000000
[   16.229186] intel_sst_acpi 80860F28:00: Got drv data max stream 25
[   16.343533] input: PC Speaker as /devices/platform/pcspkr/input/input8
[   16.511078] Bluetooth: hci0: BCM: chip id 84
[   16.511663] Bluetooth: hci0: BCM: features 0x0f
[   16.512938] Bluetooth: hci0: BCM4324B3
[   16.512945] Bluetooth: hci0: BCM4324B3 (002.004.006) build 0000
[   16.565442] Bluetooth: hci0: BCM: firmware Patch file not found, tried:
[   16.565453] Bluetooth: hci0: BCM: 'brcm/BCM4324B3.hcd'
[   16.565456] Bluetooth: hci0: BCM: 'brcm/BCM.hcd'
[   16.571163] logitech-djreceiver 0003:046D:C52B.0003: hiddev96,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2.4/input2
[   16.619780] cryptd: max_cpu_qlen set to 1000
[   16.688654] input: Logitech Wireless Device PID:4024 Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0003/0003:046D:4024.0006/input/input9
[   16.689104] input: Logitech Wireless Device PID:4024 Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0003/0003:046D:4024.0006/input/input10
[   16.689292] hid-generic 0003:046D:4024.0006: input,hidraw1: USB HID v1.11 Keyboard [Logitech Wireless Device PID:4024] on usb-0000:00:14.0-2.4/input2:1
[   17.418573] SSE version of gcm_enc/dec engaged.
[   17.420741] mousedev: PS/2 mouse device common for all mice
[   18.339931] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input14
[   18.347529] intel_rapl_common: Found RAPL domain package
[   18.347545] intel_rapl_common: Found RAPL domain core
[   18.348247] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.1.auto/input/input15
[   18.420144] mmcblk1: mmc1:0001 MBG4GC 29.1 GiB 
[   18.465374]  mmcblk1: p1 p2 p3 p4
[   18.466257] mmcblk1boot0: mmc1:0001 MBG4GC 4.00 MiB 
[   18.484814] mmcblk1boot1: mmc1:0001 MBG4GC 4.00 MiB 
[   18.486287] mmcblk1rpmb: mmc1:0001 MBG4GC 4.00 MiB, chardev (511:0)
[   18.489854] i8042: PNP: No PS/2 controller found.
[   18.490121] input: SYNA7300:00 06CB:0106 as /devices/platform/80860F41:05/i2c-5/i2c-SYNA7300:00/0018:06CB:0106.0004/input/input16
[   18.490415] hid-multitouch 0018:06CB:0106.0004: input,hidraw2: I2C HID v1.00 Device [SYNA7300:00 06CB:0106] on i2c-SYNA7300:00
[   18.539365] iTCO_vendor_support: vendor-support=0
[   18.587321] kauditd_printk_skb: 1 callbacks suppressed
[   18.587328] audit: type=1130 audit(1638112649.390:13): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-rfkill comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   18.614330] acer_wmi: Acer Laptop ACPI-WMI Extras
[   18.614391] acer_wmi: Function bitmap for Communication Button: 0x0
[   18.635856] input: Acer WMI hotkeys as /devices/virtual/input/input18
[   18.641398] iTCO_wdt iTCO_wdt.2.auto: Found a Bay Trail SoC TCO device (Version=3, TCOBASE=0x0460)
[   18.649215] bytcr_rt5640 bytcr_rt5640: quirk DMIC1_MAP enabled
[   18.649227] bytcr_rt5640 bytcr_rt5640: quirk realtek,jack-detect-source 3
[   18.649231] bytcr_rt5640 bytcr_rt5640: quirk realtek,over-current-threshold-microamp 2000
[   18.649235] bytcr_rt5640 bytcr_rt5640: quirk realtek,over-current-scale-factor 1
[   18.649239] bytcr_rt5640 bytcr_rt5640: quirk MCLK_EN enabled
[   18.672577] iTCO_wdt iTCO_wdt.2.auto: initialized. heartbeat=30 sec (nowayout=0)
[   18.741755] input: bytcr-rt5640 Headset as /devices/platform/80860F28:00/bytcr_rt5640/sound/card0/input19
[   18.783253] intel-spi intel-spi: w25q64dw (8192 Kbytes)
[   18.802948] Creating 1 MTD partitions on "intel-spi":
[   18.802965] 0x000000000000-0x000000800000 : "BIOS"
[   18.908187] input: Logitech K400 as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0003/0003:046D:4024.0006/input/input20
[   18.913303] logitech-hidpp-device 0003:046D:4024.0006: input,hidraw1: USB HID v1.11 Keyboard [Logitech K400] on usb-0000:00:14.0-2.4/input2:1
[   21.448196] audit: type=1130 audit(1638112652.250:14): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-fsck@dev-disk-by\x2duuid-24E4\x2d3B42 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   21.470796] audit: type=1130 audit(1638112652.273:15): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journal-flush comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   22.033484] audit: type=1130 audit(1638112652.836:16): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   22.063199] audit: type=1127 audit(1638112652.866:17): pid=346 uid=0 auid=4294967295 ses=4294967295 msg=' comm="systemd-update-utmp" exe="/usr/lib/systemd/systemd-update-utmp" hostname=? addr=? terminal=? res=success'
[   22.095832] audit: type=1130 audit(1638112652.896:18): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-update-utmp comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   22.177820] audit: type=1130 audit(1638112652.980:19): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=dbus comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   22.191065] audit: type=1334 audit(1638112652.993:20): prog-id=17 op=LOAD
[   22.191640] audit: type=1334 audit(1638112652.993:21): prog-id=18 op=LOAD
[   22.191864] audit: type=1334 audit(1638112652.993:22): prog-id=19 op=LOAD
[   23.598917] kauditd_printk_skb: 14 callbacks suppressed
[   23.598935] audit: type=1131 audit(1638112654.400:35): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-rfkill comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   24.159789] audit: type=1130 audit(1638112654.960:36): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user-runtime-dir@0 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   24.190411] audit: type=1101 audit(1638112654.993:37): pid=363 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_unix,pam_permit,pam_time acct="root" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   24.190434] audit: type=1103 audit(1638112654.993:38): pid=363 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:setcred grantors=? acct="root" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=failed'
[   24.190780] audit: type=1006 audit(1638112654.993:39): pid=363 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=2 res=1
[   24.190797] audit: type=1300 audit(1638112654.993:39): arch=c000003e syscall=1 success=yes exit=1 a0=9 a1=7ffd1bb3aaf0 a2=1 a3=0 items=0 ppid=1 pid=363 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=2 comm="(systemd)" exe="/usr/lib/systemd/systemd" key=(null)
[   24.190809] audit: type=1327 audit(1638112654.993:39): proctitle="(systemd)"
[   24.195907] audit: type=1105 audit(1638112654.996:40): pid=363 uid=0 auid=0 ses=2 msg='op=PAM:session_open grantors=pam_loginuid,pam_loginuid,pam_keyinit,pam_limits,pam_unix,pam_permit,pam_mail,pam_systemd,pam_env acct="root" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   24.218424] audit: type=1334 audit(1638112655.020:41): prog-id=23 op=LOAD
[   24.218484] audit: type=1300 audit(1638112655.020:41): arch=c000003e syscall=321 success=yes exit=8 a0=5 a1=7ffdb72b9660 a2=78 a3=7ffdb72b9660 items=0 ppid=1 pid=363 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=2 comm="systemd" exe="/usr/lib/systemd/systemd" key=(null)
[   35.874363] kauditd_printk_skb: 10 callbacks suppressed
[   35.874383] audit: type=1131 audit(1638112666.676:49): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-dispatcher comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   43.242336] logitech-hidpp-device 0003:046D:4024.0006: HID++ 2.0 device connected.
[   53.446727] audit: type=1131 audit(1638112684.246:50): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   53.554178] audit: type=1334 audit(1638112684.356:51): prog-id=0 op=UNLOAD
[   53.554228] audit: type=1334 audit(1638112684.356:52): prog-id=0 op=UNLOAD
[   53.554249] audit: type=1334 audit(1638112684.356:53): prog-id=0 op=UNLOAD

Last edited by Dragonsight91 (2021-11-28 21:54:00)

Dragonsight91

Member

Registered: 2021-11-28

Posts: 2

Re: [Solved] Problems with MMCONFIG on ACER Iconia W4-820 Series Tablet

After some more research, i found out that this tablet uses SDIO and not PCIe to connect the broadcom wireless chip and all other devices. Refer to ASUS_x205ta#Booting_the_x205ta_from_USB for the  solution and what additional configuration is required. So it makes sense that MMCONFIG cannot configure the PCIe bridge and also that there is no reserved area in memory for it, since there is no extended PCIe bus in the first place. 

I will leave this post here, just in case anyone comes across this issue and looks for it.