You are not logged in.

Pages: 1 2

#26 2006-02-07 10:21:55

eyolf
Member
From: Copenhagen
Registered: 2005-11-29
Posts: 339
Website

Re: powersave and suspend to ram added

Thanks. I had already made some different settings yesterday, and when I turned on today, everything came back fine, as usual, I waited some nervous seconds - and nothing happened. Great! I like powersave, I like, arch, I like linux, I like lemon pie, I like Dylan, I like you all :-)
If I now can refrain from going out, I might aspire to some monster uptime too. I suppose i should turn it off if I start moving around, though (it's a laptop), since the machine is still active even though it is suspended. Or? Do I run a greater risk of damaging the hardware if I carry it around in a suspended state?

Offline

#27 2006-02-12 17:23:21

Blaasvis
Member
Registered: 2003-01-17
Posts: 467

Re: powersave and suspend to ram added

new version is up, acpid is stopped and started now due to the shutdown problem.
USEDPMS add, some system won't wake up their monitors if enabled, some do not go off on suspend this should fix it.
added prism54 to be unloaded it seem it is causing trouble...

Freedom is what i love

Offline

#28 2006-02-15 09:25:45

Avenger
Member
Registered: 2005-11-11
Posts: 66

Re: powersave and suspend to ram added

I have a problem with suspend 2 ram, if I type 'powersave -u' the monitor goes off and after 1 sec it turns back on and I'm back where I started before trying to suspend.
I have a custom-built kernel made from the archlinux kernel26 2.6.15.2 PKGBUILD. Is there anything I need in my kernel to make this work?

The problem persists both in console and from X.

I have an ATi mobile radeon and ipw2200 wireless if that could be a problem. Here's the output from my messages.log:

Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: DIAG: Process script for event daemon.scheme.change ID 3
Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: INFO: Event: DAEMON_SCHEME_CHANGE occured.
Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: INFO: Parameters: Event - daemon.scheme.change; Current Active Scheme: scheme_performance - ACPI event line: empty
Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: DEBUG: process function: load_scheme
Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: INFO: load scheme: /etc/powersave//scheme_performance
Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: DIAG: laptop_mode already inactive, ignoring
Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: DIAG: do remounts?: 'no', set noatime: ''
Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: WARNING: could not retrieve list of disks from HAL: 
Feb 15 10:22:35 avlap [powersave-set_disk_settings][3336]: DIAG: script_return() invoked: event_id: 3, request: 0, text: execute_disk_settings finished
Feb 15 10:22:41 avlap logger: ACPI group/action undefined: hotkey / ATKD
Feb 15 10:22:41 avlap logger: ACPI group/action undefined: hotkey / ATKD
Feb 15 10:22:41 avlap logger: ACPI group/action undefined: hotkey / ATKD
Feb 15 10:22:41 avlap logger: ACPI group/action undefined: hotkey / ATKD
...
[repated alot of times]
...
Feb 15 10:23:08 avlap logger: ACPI group/action undefined: hotkey / ATKD
Feb 15 10:23:09 avlap logger: ACPI group/action undefined: hotkey / ATKD
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: Process script for event global.suspend2ram ID 6
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: INFO: Event: GLOBAL_SUSPEND2RAM occured.
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: INFO: Parameters: Event - global.suspend2ram; Current Active Scheme: scheme_performance - ACPI event line: empty
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 0
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: DEBUG: Stop services:  acpid cups netfs alsa network
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: DEBUG: Modules to unload: prism54 nvidia nvsound acx100 acx_pci hsfmodem prism54 bcm4400 emu10k1 forcedeth ipw2100 ipw2200 natsemi psmouse rt2400 ehci_hcd ohci_hcd uhci_hcd ehci-hcd usb-ohci usb-uhci snd_ens1370 snd_ens1371 en1370 en1371 via_agp via_rhine i8042 intel_mch_agp rt2500 button speedstep_smi ndiswrapper usblp
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 10|unmounting FAT/NTFS partitions
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 20|stopping services
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: Service acpid stopped
Feb 15 10:23:12 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: Service cups stopped
Feb 15 10:23:13 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: Service netfs stopped
Feb 15 10:23:13 avlap [powersave-prepare_suspend_to_ram][3909]: INFO: Service alsa stop requested but was not running. Return code: ''
Feb 15 10:23:13 avlap [powersave-prepare_suspend_to_ram][3909]: INFO: Service network stop requested but was not running. Return code: ''
Feb 15 10:23:13 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 30|ejecting PCMCIA cards
Feb 15 10:23:13 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 40|unloading modules
Feb 15 10:23:13 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 40|unloading module: ipw2200
Feb 15 10:23:13 avlap ACPI: PCI interrupt for device 0000:01:03.0 disabled
Feb 15 10:23:13 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: Modules unloaded
Feb 15 10:23:13 avlap hda: CHECK for good STATUS
Feb 15 10:23:14 avlap hdb: CHECK for good STATUS
Feb 15 10:23:14 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 50
Feb 15 10:23:14 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 60|syncing file systems
Feb 15 10:23:15 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 4, text: 101
Feb 15 10:23:15 avlap [powersave-prepare_suspend_to_ram][3909]: DIAG: script_return() invoked: event_id: 6, request: 0, text: prepare_sleep finished successfully for global.suspend2ram
Feb 15 10:23:15 avlap [powersave-do_screen_saver][3985]: DIAG: Process script for event global.suspend2ram ID 
Feb 15 10:23:15 avlap [powersave-do_screen_saver][3985]: INFO: Event: GLOBAL_SUSPEND2RAM occured.
Feb 15 10:23:15 avlap [powersave-do_screen_saver][3985]: INFO: Parameters: Event - global.suspend2ram; Current Active Scheme:  - ACPI event line: 
Feb 15 10:23:15 avlap [powersave-do_screen_saver][3985]: INFO: process script: screen_saver
Feb 15 10:23:16 avlap Stopping tasks: ==========================================================================================================================================|
Feb 15 10:23:16 avlap hci_usb 5-1:1.0: no suspend for driver hci_usb?
Feb 15 10:23:16 avlap hci_usb 5-1:1.0: no resume for driver hci_usb?
Feb 15 10:23:16 avlap Restarting tasks... done
Feb 15 10:23:16 avlap [powersave-restore_after_suspend_to_ram][4000]: DIAG: Process script for event global.resume.suspend2ram ID 7
Feb 15 10:23:16 avlap [powersave-restore_after_suspend_to_ram][4000]: INFO: Event: GLOBAL_RESUME_SUSPEND2RAM occured.
Feb 15 10:23:16 avlap [powersave-restore_after_suspend_to_ram][4000]: INFO: Parameters: Event - global.resume.suspend2ram; Current Active Scheme: scheme_performance - ACPI event line: empty
Feb 15 10:23:16 avlap ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.10
Feb 15 10:23:16 avlap ipw2200: Copyright(c) 2003-2005 Intel Corporation
Feb 15 10:23:16 avlap ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 22 (level, low) -> IRQ 22
Feb 15 10:23:16 avlap ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Feb 15 10:23:16 avlap [powersave-restore_after_suspend_to_ram][4000]: DIAG: Modules loaded
Feb 15 10:23:17 avlap [powersave-restore_after_suspend_to_ram][4000]: DIAG: Service netfs started again
Feb 15 10:23:17 avlap [powersave-restore_after_suspend_to_ram][4000]: DIAG: Service cups started again
Feb 15 10:23:17 avlap [powersave-restore_after_suspend_to_ram][4000]: DIAG: Service acpid started again
Feb 15 10:23:17 avlap [powersave-restore_after_suspend_to_ram][4000]: DIAG: script_return() invoked: event_id: 7, request: 0, text: restore_after_suspend2ram finished
Feb 15 10:23:17 avlap [powersave-do_screen_saver][3985]: DEBUG: process function: xlock_screen_saver
Feb 15 10:23:17 avlap [powersave-do_screen_saver][3985]: DIAG: script_return() invoked: event_id: 0, request: Script screen_saver, text:

Offline

#29 2006-03-18 03:40:21

_Gandalf_
Member
Registered: 2006-01-12
Posts: 735

Re: powersave and suspend to ram added

powersave -U does not work for me, using kernel26archck kernel, first it said that /boot/vmlinuz26archck does not match, i have to set SUSPEND2DISK_IGNORE_KERNEL_MISMATCH="yes" in /etc/powersave/sleep
when i set it, it complains about swap:/dev/hda8 cannot be used roll

here's my grub meny entry

title  |     Archck Silent Splash
root   (hd0,4)
kernel /vmlinuz26archck root=/dev/hda6 ro video=vesafb:ywrap,mtrr,1024x768-32@70 splash=silent,theme:darch console=tty1 resume=swap:/dev/hda8 resume2=swap:/dev/hda8 quiet
initrd /initramfs-2.6.15-archck.img

What could be wrong ??

[My Blog] | [My Repo] | [My AUR Packages]

Offline

#30 2006-03-20 17:59:36

eyolf
Member
From: Copenhagen
Registered: 2005-11-29
Posts: 339
Website

Re: powersave and suspend to ram added

After the latest upgrade to KDE 3.5.2 (in testing), powersave doesn't work anymore. Error message: 

powersave: error while loading shared libraries: libdbus-1.so.1: cannot open shared object file: No such file or directory

... which is correct enough: I have libdbus-1.so and libdbus-1.so.2, which are both links to libdbus-1.so.2.0.0.
Can I make a new softlink called libdbus-1.so.1? Or will that mess up things?

I know, this is the kind of thing I should expect when I use testing...

Offline

#31 2006-03-20 22:01:59

Blaasvis
Member
Registered: 2003-01-17
Posts: 467

Re: powersave and suspend to ram added

powersave must be rebuilded.... against the latest dbus..

Freedom is what i love

Offline

#32 2006-03-29 14:20:22

eyolf
Member
From: Copenhagen
Registered: 2005-11-29
Posts: 339
Website

Re: powersave and suspend to ram added

Is this something that will happen in an overseeable future, or should I downgrade dbus...?

Offline

#33 2006-04-03 17:50:42

matsche
Member
From: .at
Registered: 2004-04-27
Posts: 120

Re: powersave and suspend to ram added

good question - i'm waiting with upgrading my system

THX!!
cu matsche

Offline

#34 2006-04-03 17:57:21

eyolf
Member
From: Copenhagen
Registered: 2005-11-29
Posts: 339
Website

Re: powersave and suspend to ram added

For what it's worth, after the latest upgrade, cpufreq doesn't work either - same library missing. And VLC complains about the same thing... That's one popular chick, that libsysfs.so.1... :-)

Offline

#35 2006-04-05 14:28:31

matsche
Member
From: .at
Registered: 2004-04-27
Posts: 120

Re: powersave and suspend to ram added

thx for the new powersave daemon!

I added kpowersave 0.5.11 to the AUR:
http://aur.archlinux.org/packages.php?d … =1&ID=4102

THX!!
cu matsche

Offline

#36 2006-04-05 15:30:45

stonecrest
Member
From: Boulder
Registered: 2005-01-22
Posts: 1,190

Re: powersave and suspend to ram added

matsche wrote:

thx for the new powersave daemon!

Seconded smile

I am a gated community.

Offline

#37 2006-05-04 19:29:55

eNTi
Member
Registered: 2006-04-30
Posts: 109

Re: powersave and suspend to ram added

powersave -u:

checking nvidia
could not unload module 'nvidia', usage count: 14
...
starting acpid:
##  stty: standard input: Invalid argument
##  :: Starting acpid 9G   [BUSY] acpid: can't open /proc/acpi/event: Device or resource busy
##  9G   [FAIL]

Remounting filesystems:
  not necessary.

<21><Thu></home>
root@defiler $ /etc/rc.d/acpid start
:: Starting acpid                                                                                                                                                            [BUSY] acpid: can't open /proc/acpi/event: Device or resource busy
                                                                                                                                                                             [FAIL]

Offline

#38 2006-05-04 20:16:00

stonecrest
Member
From: Boulder
Registered: 2005-01-22
Posts: 1,190

Re: powersave and suspend to ram added

eNTi, do you have both acpi and powersaved in your rc.conf's DAEMONS? powersaved starts acpi automatically (as well as dbus and hal), so remove all of those and just start powersaved.

I am a gated community.

Offline

#39 2006-05-05 15:18:29

eNTi
Member
Registered: 2006-04-30
Posts: 109

Re: powersave and suspend to ram added

stonecrest wrote:

eNTi, do you have both acpi and powersaved in your rc.conf's DAEMONS? powersaved starts acpi automatically (as well as dbus and hal), so remove all of those and just start powersaved.

i didn't have acpid in my rc.conf, and i still can't unload the nvidia module? is there a problem with 4k stacks, because i'm on beyond-patchset.

Offline

#40 2006-08-22 11:48:25

emuranch
Member
Registered: 2006-04-14
Posts: 37

Re: powersave and suspend to ram added

Thank you for this!  I spent forever trying to make suspend work in Ubuntu, but now in Arch I just install your package, add my wireless card to the unload list, and suspend works!

Offline

#41 2006-08-22 13:49:13

Gullible Jones
Member
Registered: 2004-12-29
Posts: 4,863

Re: powersave and suspend to ram added

powersave -u fails here... It runs, but nothing at all happens. Here's the log...

suspend2ram initiated: 2006-08-22 09:41:26
Debug info follows here, please include in your bug reports. Thanks.
--------------------------------------------------------------------
Loaded modules:
Module                  Size  Used by
snd_seq_oss            31360  0
snd_seq_midi_event      6528  1 snd_seq_oss
snd_seq                50256  4 snd_seq_oss,snd_seq_midi_event
snd_pcm_oss            37664  0
snd_mixer_oss          16128  1 snd_pcm_oss
ppdev                   7812  0
lp                      9732  0
snd_ens1371            21408  0
gameport               11656  1 snd_ens1371
snd_rawmidi            20256  1 snd_ens1371
snd_seq_device          6796  3 snd_seq_oss,snd_seq,snd_rawmidi
snd_ac97_codec         93216  1 snd_ens1371
snd_ac97_bus            2304  1 snd_ac97_codec
snd_pcm                76292  3 snd_pcm_oss,snd_ens1371,snd_ac97_codec
snd_timer              19972  2 snd_seq,snd_pcm
snd                    45924  10 snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_ens1371,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timersoundcore               7776  1 snd
snd_page_alloc          8072  1 snd_pcm
shpchp                 36520  0
pci_hotplug            27588  1 shpchp
ide_cd                 36256  0
joydev                  8384  0
cdrom                  35616  1 ide_cd
i2c_viapro              7828  0
i2c_core               17536  1 i2c_viapro
via_ircc               19860  0
irda                  121912  1 via_ircc
rtc                    10676  0
parport_pc             24484  1
parport                33480  3 ppdev,lp,parport_pc
evdev                   8192  1
via_rhine              20356  0
mii                     5248  1 via_rhine
uhci_hcd               20620  0
crc_ccitt               2176  1 irda
ppp_generic            24852  0
slhc                    6528  1 ppp_generic
ehci_hcd               29576  0
via                    43104  1
drm                    63508  2 via
via_agp                 8320  1
agpgart                26980  2 drm,via_agp
usbcore               113536  3 uhci_hcd,ehci_hcd
ext3                  128264  2
jbd                    56084  1 ext3
ide_disk               14208  3
via82cxxx               8580  0 [permanent]
ide_core              113736  3 ide_cd,ide_disk,via82cxxx

Memory info:
             total       used       free     shared    buffers     cached
Mem:        369532     318296      51236          0      40228     145616
-/+ buffers/cache:     132452     237080
Swap:            0          0          0

/proc/cmdline: root=/dev/hda1 ro
------------------------------------------------------------------------------
========we are going to sleep, preparing.========
== checking runlevel ==
  no shutdown/reboot in progress, good.
== Unmounting FAT/NTFS filesystems: ==
  none found in /etc/mtab
== FAT/NTFS filesystems unmounted ==
Stopping services: (' acpid cups netfs alsa network' configured)
stopping acpid:
##  stty: standard input: Invalid argument
##  :: Stopping acpid [-9G   [BUSY] [-9G   [DONE]
stopping cups:
##  stty: standard input: Invalid argument
##  :: Stopping CUPS Daemon [-9G   [BUSY] [-9G   [DONE]
stopping alsa:
##  stty: standard input: Invalid argument
##  :: Saving ALSA Levels [-9G   [BUSY] [-9G   [DONE]
stopping network:
##  stty: standard input: Invalid argument
##  stty: standard input: Invalid argument
##  :: Stopping Network [-9G   [BUSY] [-9G   [DONE]
ejecting PCMCIA cards...

------------------------------------------------------------------------------
Unloading modules: ('prism54 nvidia nvsound acx100 acx_pci hsfmodem prism54 bcm4400 emu10k1 forcedeth ipw2100 ipw2200 natsemi psmouse rt2400 ehci_hcd ohci_hcd uhci_hcd ehci-hcd usb-ohci usb-uhci snd_ens1370 snd_ens1371 en1370 en1371 via_agp via_rhine i8042 intel_mch_agp rt2500 button speedstep_smi ndiswrapper usblp' configured)
checking prism54
checking nvidia
checking nvsound
checking acx100
checking acx_pci
checking hsfmodem
checking prism54
checking bcm4400
checking emu10k1
checking forcedeth
checking ipw2100
checking ipw2200
checking natsemi
checking psmouse
checking rt2400
checking ehci_hcd
# trying to unload: ehci_hcd
unloaded: ehci_hcd
checking ohci_hcd
checking uhci_hcd
# trying to unload: uhci_hcd
unloaded: uhci_hcd
checking ehci-hcd
checking usb-ohci
checking usb-uhci
checking snd_ens1370
checking snd_ens1371
# trying to unload: snd_ens1371
unloaded: snd_ens1371
checking en1370
checking en1371
checking via_agp
could not unload module 'via_agp', usage count: 1

== restore_after_sleep: restart and reload everything ==

Resuming:
---------
switched back to console: ''
reactivating ACPI fan FAN

Reloading modules:
  snd_ens1371
  uhci_hcd
  ehci_hcd
inserting PCMCIA cards...

Restarting services:
starting network:
##  stty: standard input: Invalid argument
##  :: Starting Network [-9G   [BUSY] [-9G   [DONE]
starting alsa:
##  stty: standard input: Invalid argument
##  :: Restoring ALSA Levels [-9G   [BUSY] [-9G   [DONE]
starting cups:
##  stty: standard input: Invalid argument
##  :: Starting CUPS Daemon [-9G   [BUSY] [-9G   [DONE]
starting acpid:
##  stty: standard input: Invalid argument
##  :: Starting acpid [-9G   [BUSY] acpid: can't open /proc/acpi/event: Device or resource busy
##  [-9G   [FAIL]

Remounting filesystems:
  not necessary.

Evidently all this happened in a fraction of a second.

Offline

#42 2006-10-13 16:43:16

pelle.k
Member
From: Åre, Sweden (EU)
Registered: 2006-04-30
Posts: 667

Re: powersave and suspend to ram added

suspend2ram initiated: 2006-10-13 17:52:30
Debug info follows here, please include in your bug reports. Thanks.
--------------------------------------------------------------------
Loaded modules:
Module                  Size  Used by
ipv6                  237472  10
cpufreq_ondemand        5644  1
speedstep_centrino      7220  1
freq_table              4240  1 speedstep_centrino
ndiswrapper           187600  0
ntfs                  220564  1
nls_cp437               5888  1
vfat                   10624  1
fat                    45596  1 vfat
eth1394                16772  0
tsdev                   6336  0
joydev                  8256  0
snd_seq_oss            29440  0
snd_seq_midi_event      6528  1 snd_seq_oss
snd_seq                47184  4 snd_seq_oss,snd_seq_midi_event
snd_seq_device          6924  2 snd_seq_oss,snd_seq
rtc                    10292  0
snd_pcm_oss            39072  0
usbhid                 47776  0
snd_mixer_oss          14592  1 snd_pcm_oss
r1000                  15232  0
ohci1394               31408  0
ieee1394               83672  2 eth1394,ohci1394
ipw2200               102596  0
ieee80211              29640  1 ipw2200
ieee80211_crypt         5120  1 ieee80211
r8169                  24328  0
psmouse                35720  0
serio_raw               5636  0
i2c_i801                7308  0
nvidia               4527956  12
i2c_core               17280  2 i2c_i801,nvidia
snd_hda_intel          14484  2
snd_hda_codec         146304  1 snd_hda_intel
snd_pcm                67972  3 snd_pcm_oss,snd_hda_intel,snd_hda_codec
snd_timer              19204  2 snd_seq,snd_pcm
snd                    42724  13 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer
soundcore               7776  1 snd
pcspkr                  2816  0
uhci_hcd               21004  0
ehci_hcd               29576  0
intel_agp              19740  1
agpgart                25944  2 nvidia,intel_agp
snd_page_alloc          7816  2 snd_hda_intel,snd_pcm
evdev                   7936  1
usbcore               110852  5 ndiswrapper,usbhid,uhci_hcd,ehci_hcd
ext3                  122504  2
jbd                    55080  1 ext3
mbcache                 7044  1 ext3
sd_mod                 16640  7
ide_cd                 35616  0
cdrom                  34464  1 ide_cd
generic                 4996  0 [permanent]
sata_via                7172  5
libata                 85908  1 sata_via
piix                    9220  0 [permanent]
ide_core              109256  3 ide_cd,generic,piix

Memory info:
             total       used       free     shared    buffers     cached
Mem:       1035700     724704     310996          0      63400     484792
-/+ buffers/cache:     176512     859188
Swap:       979924          0     979924

/proc/cmdline: root=/dev/sda5 ro
------------------------------------------------------------------------------
========we are going to sleep, preparing.========
== checking runlevel ==
  no shutdown/reboot in progress, good.
== Unmounting FAT/NTFS filesystems: ==
  device /dev/sdb1 mounted on '/media/sdb1'
  device /dev/sda1 mounted on '/media/sda1'
trying to umount device: '/dev/sdb1' '/media/sdb1' -t 'vfat' -o 'rw,utf8,umask=007,gid=100'
  success.
trying to umount device: '/dev/sda1' '/media/sda1' -t 'ntfs' -o 'rw,nls=utf8,umask=007,gid=100'
  success.
== FAT/NTFS filesystems unmounted ==
Stopping services: (' acpid cups netfs alsa network' configured)
stopping acpid:
##  stty: standard input: Invalid argument
##  :: Stopping acpid 9G   [BUSY] 9G   [DONE]
stopping netfs:
##  stty: standard input: Invalid argument
##  :: Unmounting Network Filesystems 9G   [BUSY] 9G   [DONE]
stopping alsa:
##  stty: standard input: Invalid argument
##  :: Saving ALSA Levels 9G   [BUSY] 9G   [DONE]
stopping network:
##  stty: standard input: Invalid argument
##  stty: standard input: Invalid argument
##  :: Stopping Network 9G   [BUSY] 9G   [DONE]
ejecting PCMCIA cards...

------------------------------------------------------------------------------
Unloading modules: (' nvsound acx100 acx_pci hsfmodem prism54 bcm4400 emu10k1 forcedeth ipw2100 ipw2200 natsemi psmouse rt2400 ehci_hcd ohci_hcd uhci_hcd ehci-hcd usb-ohci usb-uhci snd_ens1370 snd_ens1371 en1370 en1371 via_agp via_rhine i8042 intel_mch_agp rt2500 button speedstep_smi ndiswrapper usblp' configured)
checking nvsound
checking acx100
checking acx_pci
checking hsfmodem
checking prism54
checking bcm4400
checking emu10k1
checking forcedeth
checking ipw2100
checking ipw2200
# trying to unload: ipw2200
unloaded: ipw2200
checking natsemi
checking psmouse
# trying to unload: psmouse
unloaded: psmouse
checking rt2400
checking ehci_hcd
# trying to unload: ehci_hcd
unloaded: ehci_hcd
checking ohci_hcd
checking uhci_hcd
# trying to unload: uhci_hcd
unloaded: uhci_hcd
checking ehci-hcd
checking usb-ohci
checking usb-uhci
checking snd_ens1370
checking snd_ens1371
checking en1370
checking en1371
checking via_agp
checking via_rhine
checking i8042
checking intel_mch_agp
checking rt2500
checking button
checking speedstep_smi
checking ndiswrapper
# trying to unload: ndiswrapper
unloaded: ndiswrapper
checking usblp
------------------------------------------------------------------------------
prepare_sleep finished for suspend2ram
------------------------------------------------------------------------------
/usr/sbin/s2ram not found, falling back to echo.
==== finished, return code 0 ====
========we are back from suspend, cleaning up.========

== restore_after_sleep: restart and reload everything ==

Resuming:
---------
switched back to console: ' 7'

Reloading modules:
  ndiswrapper
  uhci_hcd
  ehci_hcd
  psmouse
  ipw2200
inserting PCMCIA cards...

Restarting services:
starting network:
##  stty: standard input: Invalid argument
##  :: Starting Network 9G   [BUSY] Error for wireless request "Set ESSID" (8B1A) :
##      SET failed on device wlan0 ; No such device.
##  9G   [FAIL]
starting alsa:
##  stty: standard input: Invalid argument
##  :: Restoring ALSA Levels 9G   [BUSY] 9G   [DONE]
starting netfs:
##  stty: standard input: Invalid argument
##  :: Mounting Network Filesystems 9G   [BUSY] 9G   [DONE]
starting acpid:
##  stty: standard input: Invalid argument
##  :: Starting acpid 9G   [BUSY] acpid: can't open /proc/acpi/event: Device or resource busy
##  9G   [FAIL]

Remounting filesystems:
  mounted '/dev/sda1' to '/media/sda1', options '-o rw,nls=utf8,umask=007,gid=100'
  mounted '/dev/sdb1' to '/media/sdb1', options '-o rw,utf8,umask=007,gid=100'

======================================
restore_after_suspend_to_ram: finished

Why is this? 

##  stty: standard input: Invalid argument

"Your beliefs can be like fences that surround you.
You must first see them or you will not even realize that you are not free, simply because you will not see beyond the fences.
They will represent the boundaries of your experience."
SETH / Jane Roberts

Offline

Pages: 1 2

Board footer

Powered by FluxBB