You are not logged in.
Hey there,
I just upgraded my NAS with larger HDDs (WD Red 4 TB to Seagate Ironwolf 12 TB). After cloning one of them with Clonezilla, I got this error after boot:
[ 154.812778] ata4.00: invalid checksum 0x2 on log page 10h
[ 154.812790] ata4: log page 10h reported inactive tag 0
[ 154.813097] ata4.00: exception Emask 0x1 SAct 0x80000006 SErr 0x0 action 0x0
[ 154.813412] ata4.00: irq_stat 0x40000008
[ 154.813604] ata4.00: failed command: READ FPDMA QUEUED
[ 154.813861] ata4.00: cmd 60/00:08:20:26:73/01:00:09:00:00/40 tag 1 ncq dma 131072 in
res 40/00:10:00:69:00/00:00:e3:01:00/40 Emask 0x1 (device error)
[ 154.814521] ata4.00: status: { DRDY }
[ 154.814692] ata4.00: failed command: WRITE FPDMA QUEUED
[ 154.814943] ata4.00: cmd 61/40:10:00:69:00/05:00:e3:01:00/40 tag 2 ncq dma 688128 out
res 40/00:10:00:69:00/00:00:e3:01:00/40 Emask 0x1 (device error)
[ 154.815731] ata4.00: status: { DRDY }
[ 154.815935] ata4.00: failed command: READ FPDMA QUEUED
[ 154.816187] ata4.00: cmd 60/00:f8:20:25:73/01:00:09:00:00/40 tag 31 ncq dma 131072 in
res 40/00:10:00:69:00/00:00:e3:01:00/40 Emask 0x1 (device error)
[ 154.816824] ata4.00: status: { DRDY }
[ 154.925135] ata4.00: configured for UDMA/133
[ 154.925221] sd 3:0:0:0: [sdc] tag#1 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 154.925238] sd 3:0:0:0: [sdc] tag#1 Sense Key : Illegal Request [current]
[ 154.925253] sd 3:0:0:0: [sdc] tag#1 Add. Sense: Unaligned write command
[ 154.925269] sd 3:0:0:0: [sdc] tag#1 CDB: Read(16) 88 00 00 00 00 00 09 73 26 20 00 00 01 00 00 00
[ 154.925280] print_req_error: I/O error, dev sdc, sector 158541344
[ 154.925697] sd 3:0:0:0: [sdc] tag#31 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 154.925713] sd 3:0:0:0: [sdc] tag#31 Sense Key : Illegal Request [current]
[ 154.925727] sd 3:0:0:0: [sdc] tag#31 Add. Sense: Unaligned write command
[ 154.925742] sd 3:0:0:0: [sdc] tag#31 CDB: Read(16) 88 00 00 00 00 00 09 73 25 20 00 00 01 00 00 00
[ 154.925751] print_req_error: I/O error, dev sdc, sector 158541088
[ 154.926069] ata4: EH complete
SMART data:
# smartctl -a /dev/sdc
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-18-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate IronWolf
Device Model: ST12000VN0008-2PH103
Serial Number: XXX
LU WWN Device Id: 5 000c50 0c9110c5d
Firmware Version: SC61
User Capacity: 12.000.138.625.024 bytes [12,0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Dec 26 21:35:45 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 567) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: (1104) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 063 061 044 Pre-fail Always - 59411605
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 4
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 128
7 Seek_Error_Rate 0x000f 063 060 045 Pre-fail Always - 1990119
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 18
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 4
18 Head_Health 0x000b 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 099 099 000 Old_age Always - 1
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 058 049 040 Old_age Always - 42 (Min/Max 25/42)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 31
194 Temperature_Celsius 0x0022 042 049 000 Old_age Always - 42 (0 25 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 8
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Pressure_Limit 0x0023 100 100 001 Pre-fail Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 10h+11m+52.737s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 7845334924
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 32204736
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 18 hours (0 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 53 00 e0 25 73 09 Error: WP at LBA = 0x097325e0 = 158541280
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 40 ff ff ff 4f 00 00:15:00.212 WRITE FPDMA QUEUED
60 00 00 20 26 73 49 00 00:14:53.918 READ FPDMA QUEUED
60 00 00 20 25 73 49 00 00:14:53.913 READ FPDMA QUEUED
61 00 40 ff ff ff 4f 00 00:14:51.855 WRITE FPDMA QUEUED
61 00 40 ff ff ff 4f 00 00:14:51.855 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 18 -
# 2 Extended offline Aborted by host 90% 18 -
# 3 Short offline Completed without error 00% 18 -
# 4 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Reallocated_Sector_Ct doesn't look good to me. Furthermore, it's more noisy than before. Is my brand new hard drive already failing?
EDIT: Figures are getting worse after switching the SATA cable:
# smartctl -a /dev/sdb
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-18-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate IronWolf
Device Model: ST12000VN0008-2PH103
Serial Number: XXX
LU WWN Device Id: 5 000c50 0c9110c5d
Firmware Version: SC61
User Capacity: 12.000.138.625.024 bytes [12,0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Dec 26 22:15:09 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 567) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: (1104) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 063 061 044 Pre-fail Always - 66405997
3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 6
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 408
7 Seek_Error_Rate 0x000f 063 060 045 Pre-fail Always - 2007495
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 19
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 5
18 Head_Health 0x000b 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 099 099 000 Old_age Always - 1
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 049 040 Old_age Always - 34 (Min/Max 32/34)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 33
194 Temperature_Celsius 0x0022 034 049 000 Old_age Always - 34 (0 25 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 8
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Pressure_Limit 0x0023 100 100 001 Pre-fail Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 10h+27m+34.865s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 7852313820
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 32220232
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 18 hours (0 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 53 00 e0 25 73 09 Error: WP at LBA = 0x097325e0 = 158541280
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 40 ff ff ff 4f 00 00:15:00.212 WRITE FPDMA QUEUED
60 00 00 20 26 73 49 00 00:14:53.918 READ FPDMA QUEUED
60 00 00 20 25 73 49 00 00:14:53.913 READ FPDMA QUEUED
61 00 40 ff ff ff 4f 00 00:14:51.855 WRITE FPDMA QUEUED
61 00 40 ff ff ff 4f 00 00:14:51.855 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 19 -
# 2 Short offline Completed without error 00% 18 -
# 3 Extended offline Aborted by host 90% 18 -
# 4 Short offline Completed without error 00% 18 -
# 5 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Last edited by Silenzium (2021-12-27 09:09:52)
Offline
Your guess is correct. That count going up means the disk is not safe for data whatsoever from now on.
Offline
Reallocated_Sector_Ct is now at 904. I will return that HDD.
Offline