You are not logged in.
This issue is it wouldn't recognize the USB as a removable drive and I don't know how to check for it because it won't show up anywhere
The only thing I do know is that it was formatted to HDD
I don't know who to check or change it and I don't know if I need any new things to access the drive or change it
Last edited by DeepYellow (2022-06-13 15:37:14)
Offline
are you trying to recover data or asking how to format a usb stick that wont show up cause you formatted it on a wii u ?
need alot more info
Offline
I thought that it wasn't much to go off of but there is nothing on it, I wiped it before hand. I just need to format it back to something that gets recognized on my PC
Offline
Please run `dmesg -W` then plug in the usb drive (and wait a few seconds), then break (Ctrl-C) the dmesg process. Post the output from that dmesg here in code tags.
Also post the output of each of the following with the usb drive still plugged in:
lsblk
pacman -Q linux
uname -a
Last edited by Trilby (2022-06-13 15:45:42)
"UNIX is simple and coherent..." - Dennis Ritchie, "GNU's Not UNIX" - Richard Stallman
Offline
[19037.958368] usb 2-2: USB disconnect, device number 4
[19047.101563] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd
[19047.119223] usb 2-2: New USB device found, idVendor=0781, idProduct=5591, bcdDevice= 1.00
[19047.119244] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[19047.119253] usb 2-2: Product: SanDisk 3.2Gen1
[19047.119260] usb 2-2: Manufacturer: USB
[19047.120824] usb-storage 2-2:1.0: USB Mass Storage device detected
[19047.121124] scsi host3: usb-storage 2-2:1.0
[19048.135506] scsi 3:0:0:0: Direct-Access USB SanDisk 3.2Gen1 1.00 PQ: 0 ANSI: 6
[19048.136243] sd 3:0:0:0: [sdb] 240353280 512-byte logical blocks: (123 GB/115 GiB)
[19048.136654] sd 3:0:0:0: [sdb] Write Protect is off
[19048.136661] sd 3:0:0:0: [sdb] Mode Sense: 43 00 00 00
[19048.137026] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[19048.147538] sd 3:0:0:0: [sdb] Attached SCSI removable disk
Please run `dmesg -W` then plug in the usb drive (and wait a few seconds), then break (Ctrl-C) the dmesg process. Post the output from that dmesg here in code tags.
Also post the output of each of the following with the usb drive still plugged in:
lsblk pacman -Q linux uname -a
Offline
So that's one out of four bits of requested information. Should I give you one part out of four of the solution? Dmesg clearly shows it is recognized and even assigned a block device node.
"UNIX is simple and coherent..." - Dennis Ritchie, "GNU's Not UNIX" - Richard Stallman
Offline
sorry dude I was tired last night and didn't read it right
linux 5.18.3.arch1-1
Linux archlinux 5.18.3-arch1-1 #1 SMP PREEMPT_DYNAMIC Thu, 09 Jun 2022 16:14:10 +0000 x86_64 GNU/Linux
sdb 8:16 1 114.6G 0 disk <my usb
So that's one out of four bits of requested information. Should I give you one part out of four of the solution? Dmesg clearly shows it is recognized and even assigned a block device node.
Last edited by DeepYellow (2022-06-22 16:25:59)
Offline
Ok, so dmesg sees the disk, and lsblk sees the disk - this is in direct contrast to the symptoms you claimed in the initial post. So what's the problem? Is there a remaining problem, or is everything working now?
If there still is a problem, the fact that you appear to be running a custom kernel could be relevant. What kernel is it?
Last edited by Trilby (2022-06-23 13:41:59)
"UNIX is simple and coherent..." - Dennis Ritchie, "GNU's Not UNIX" - Richard Stallman
Offline
5.18.5-arch1-1 | I have not changed it from what I had it on so it probably either the long-term or the stable idk
The problem is that it won't show up in the Dolphin file manager so I suppose its a dolphin or desktop thing maybe I really don't know
Ok, so dmesg sees the disk, and lsblk sees the disk - this is in direct contrast to the symptoms you claimed in the initial post. So what's the problem? Is there a remaining problem, or is everything working now?
If there still is a problem, the fact that you appear to be running a custom kernel could be relevant. What kernel is it?
Last edited by DeepYellow (2022-06-23 03:01:42)
Offline
Dolphin uses udisks, if the stick is now a file system not recognized by udisks it won't pop up. Which instructions did you follow to install Arch? You should be familiar with the basic building blocks like lsblk, mount, fdisk and so to check in what way the stick is recognized now. From the looks of it you just want to partition/format it again with a "normal" file system?
https://wiki.archlinux.org/title/Partit … ning_tools
https://wiki.archlinux.org/title/File_systems
Offline
I have not changed it from what I had it on...
So this is then not an arch linux system - or at least not one you installed. I don't know what "it" refers to here, but the union of the set of things that have a linux kernel pre-installed and those that can be called a supported arch linux system is an empty set: there's no such thing.
edit: sorry disregard these questions about the uname output - though it still seems odd that you wouldn't know what kernel package you had.
Last edited by Trilby (2022-06-23 13:42:54)
"UNIX is simple and coherent..." - Dennis Ritchie, "GNU's Not UNIX" - Richard Stallman
Offline
@Trilby that's the standard linux kernel package from where I'm standing, why do you think it's a different package?
Offline
I was misled by the "PREEMPT_DYNAMIC" rather than PREEMPT. I don't recall uname including _DYNAMIC previously.
Last edited by Trilby (2022-06-23 14:22:52)
"UNIX is simple and coherent..." - Dennis Ritchie, "GNU's Not UNIX" - Richard Stallman
Offline