You are not logged in.
I added usbcore.autosuspend=-1 to my grub boot parameters
dmesg output when trying to use the expresscard:
592.132481] </TASK>
[ 593.353593] xhci_hcd 0000:05:00.0: Download to external ROM TO: 0
[ 593.919130] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 593.919147] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 3
[ 593.927548] xhci_hcd 0000:05:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x0000001100000090
[ 593.927986] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 593.927991] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 4
[ 593.927996] xhci_hcd 0000:05:00.0: Host supports USB 3.0 SuperSpeed
[ 593.931095] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[ 593.931101] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 593.931104] usb usb3: Product: xHCI Host Controller
[ 593.931106] usb usb3: Manufacturer: Linux 6.6.23-1-lts xhci-hcd
[ 593.931109] usb usb3: SerialNumber: 0000:05:00.0
[ 593.932756] hub 3-0:1.0: USB hub found
[ 593.932832] hub 3-0:1.0: 2 ports detected
[ 593.933053] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 593.933106] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06
[ 593.933110] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 593.933114] usb usb4: Product: xHCI Host Controller
[ 593.933116] usb usb4: Manufacturer: Linux 6.6.23-1-lts xhci-hcd
[ 593.933118] usb usb4: SerialNumber: 0000:05:00.0
[ 593.933949] hub 4-0:1.0: USB hub found
[ 593.934020] hub 4-0:1.0: 2 ports detected
[ 594.181907] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[ 594.324678] usb 3-1: New USB device found, idVendor=048d, idProduct=04d2, bcdDevice= 1.00
[ 594.324686] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 594.324688] usb 3-1: Product: UDisk
[ 594.324689] usb 3-1: Manufacturer: General
[ 594.324691] usb 3-1: SerialNumber: Љ
[ 594.330439] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 594.330698] scsi host6: usb-storage 3-1:1.0
[ 605.462348] xhci_hcd 0000:05:00.0: xHCI host controller not responding, assume dead
[ 605.462381] xhci_hcd 0000:05:00.0: HC died; cleaning up
[ 605.462454] usb 3-1: USB disconnect, device number 2Last edited by T_Faded (2024-04-09 03:08:27)
Offline
Tried rebooting dmesg output:
[ 113.367715] pci 0000:05:00.0: [1912:0015] type 00 class 0x0c0330
[ 113.367795] pci 0000:05:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[ 113.368129] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[ 113.368605] pci 0000:05:00.0: BAR 0: assigned [mem 0xf3100000-0xf3101fff 64bit]
[ 113.368704] pci 0000:05:00.0: enabling device (0000 -> 0002)
[ 115.361091] xhci_hcd 0000:05:00.0: Timeout for Set DATAX step: 238
[ 115.361097] xhci_hcd 0000:05:00.0: ROM Download Step 238 failed at position 952 bytes with (-110)
[ 115.481406] xhci_hcd 0000:05:00.0: Timeout for Set DATAX step: 0
[ 115.481413] xhci_hcd 0000:05:00.0: Firmware Download Step 0 failed at position 0 bytes with (-110).
[ 115.481415] xhci_hcd 0000:05:00.0: firmware failed to download (-110).
[ 115.481434] xhci_hcd: probe of 0000:05:00.0 failed with error -110
[ 115.690483] wlan0: authenticate with 74:da:da:26:44:9c
[ 115.694658] wlan0: send auth to 74:da:da:26:44:9c (try 1/3)
[ 115.802641] wlan0: send auth to 74:da:da:26:44:9c (try 2/3)
[ 115.909046] wlan0: send auth to 74:da:da:26:44:9c (try 3/3)
[ 116.015678] wlan0: authentication with 74:da:da:26:44:9c timed out
[ 117.180751] pci 0000:05:00.0: [1912:0015] type 00 class 0x0c0330
[ 117.180802] pci 0000:05:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[ 117.181052] pci 0000:05:00.0: PME# supported from D0 D3hot
[ 117.181421] pci 0000:05:00.0: BAR 0: assigned [mem 0xf3100000-0xf3101fff 64bit]
[ 117.181465] pci 0000:05:00.0: enabling device (0000 -> 0002)
[ 124.009974] pci 0000:05:00.0: xHCI HW not ready after 5 sec (HC bug?) status = 0x1801
[ 124.010082] pci 0000:05:00.0: quirk_usb_early_handoff+0x0/0x7d0 took 6674727 usecs
[ 124.036678] wlan0: authenticate with 74:da:da:26:44:9d
[ 124.042346] wlan0: send auth to 74:da:da:26:44:9d (try 1/3)
[ 124.062251] wlan0: authenticated
[ 124.067426] wlan0: associate with 74:da:da:26:44:9d (try 1/3)
[ 124.096553] wlan0: RX AssocResp from 74:da:da:26:44:9d (capab=0x31 status=0 aid=3)
[ 124.115970] wlan0: associated
[ 151.044884] xhci_hcd 0000:05:00.0: Download to external ROM TO: 0
[ 151.184055] xhci_hcd 0000:05:00.0: Timeout for Set DATAX step: 2
[ 151.184058] xhci_hcd 0000:05:00.0: Firmware Download Step 2 failed at position 8 bytes with (-110).
[ 151.184060] xhci_hcd 0000:05:00.0: firmware failed to download (-110).
[ 151.184079] xhci_hcd: probe of 0000:05:00.0 failed with error -110Offline