Arch Linux

Jakie121

Member

Registered: 2024-04-26

Posts: 1

Bluetooth service was skipped because of an unmet condition check

I had Bluez, and Bluetooth tools installed. My AX200 works in arch Linux out of the box but then my Arch decided to make Bluetooth start impossible. I am unable to find the reason why the Bluetooth is disabled.
reinstall arch for these stuffs are painful. I don't have any empty backup drives

modprobe bluetooth

returns nothing

modprobe btusb 

returns

modprobe: ERROR: could not insert 'btusb': Unknown symbol in module, or unknown parameter (see dmesg)

uname -r:
6.8.7-arch1-1

I have used LTS version as well no fix.
I have checked the the conf in the systemctl bluetooth and blacklists and modprobe confs for bluetooth. They seems to okay.
rfkill are all unblocked

rfkill
ID TYPE      DEVICE                 SOFT      HARD
 0 wlan      ideapad_wlan      unblocked unblocked
 1 bluetooth ideapad_bluetooth unblocked unblocked
 2 wlan      phy0              unblocked unblocked
 3 wlan      phy1              unblocked unblocked

lsusb detects by bluetooth:
Bus 003 Device 004: ID 8087:0029 Intel Corp. AX200 Bluetooth

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. Hub
Bus 001 Device 003: ID 048d:c101 Integrated Technology Express, Inc. ITE Device(8910)
Bus 001 Device 018: ID 1b1c:1bc6 Corsair CORSAIR K70 RGB PRO Optical-Mechanical Gaming Keyboard
Bus 001 Device 019: ID 046d:c547 Logitech, Inc. USB Receiver
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 002: ID 0e8d:7961 MediaTek Inc. Wireless_Device
Bus 002 Device 003: ID 05e3:0620 Genesys Logic, Inc. GL3523 Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 2972:0047 FiiO Electronics Technology FiiO K3
Bus 003 Device 004: ID 8087:0029 Intel Corp. AX200 Bluetooth
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub

lspci doesnt have bluetooth but this instead:
04:00.0 Network controller: Intel Corporation Wi-Fi 6 AX200 (rev 1a)

00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne Root Complex
00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne IOMMU
00:01.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Renoir PCIe Dummy Host Bridge
00:01.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Renoir PCIe GPP Bridge
00:01.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne PCIe GPP Bridge
00:02.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Renoir PCIe Dummy Host Bridge
00:02.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne PCIe GPP Bridge
00:02.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne PCIe GPP Bridge
00:02.4 PCI bridge: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne PCIe GPP Bridge
00:08.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Renoir PCIe Dummy Host Bridge
00:08.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Renoir Internal PCIe GPP Bridge to Bus
00:08.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Renoir Internal PCIe GPP Bridge to Bus
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 51)
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 51)
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Cezanne Data Fabric; Function 0
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Cezanne Data Fabric; Function 1
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Cezanne Data Fabric; Function 2
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Cezanne Data Fabric; Function 3
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Cezanne Data Fabric; Function 4
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Cezanne Data Fabric; Function 5
00:18.6 Host bridge: Advanced Micro Devices, Inc. [AMD] Cezanne Data Fabric; Function 6
00:18.7 Host bridge: Advanced Micro Devices, Inc. [AMD] Cezanne Data Fabric; Function 7
01:00.0 VGA compatible controller: NVIDIA Corporation GA104M [GeForce RTX 3070 Mobile / Max-Q] (rev a1)
01:00.1 Audio device: NVIDIA Corporation GA104 High Definition Audio Controller (rev a1)
02:00.0 Non-Volatile memory controller: Kingston Technology Company, Inc. A2000 NVMe SSD SM2263EN (rev 03)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8211/8411 PCI Express Gigabit Ethernet Controller (rev 15)
04:00.0 Network controller: Intel Corporation Wi-Fi 6 AX200 (rev 1a)
05:00.0 Non-Volatile memory controller: Micron/Crucial Technology P2 [Nick P2] / P3 / P3 Plus NVMe PCIe SSD (DRAM-less) (rev 01)
06:00.0 Non-Essential Instrumentation [1300]: Advanced Micro Devices, Inc. [AMD] Zeppelin/Raven/Raven2 PCIe Dummy Function (rev c5)
06:00.2 Encryption controller: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 10h-1fh) Platform Security Processor
06:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne USB 3.1
06:00.4 USB controller: Advanced Micro Devices, Inc. [AMD] Renoir/Cezanne USB 3.1
06:00.5 Multimedia controller: Advanced Micro Devices, Inc. [AMD] ACP/ACP3X/ACP6x Audio Coprocessor (rev 01)
06:00.6 Audio device: Advanced Micro Devices, Inc. [AMD] Family 17h/19h HD Audio Controller
07:00.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 81)
07:00.1 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 81)

hi guys I need to have this prob solved so I could have my bluetooth headphone connected to it

edit:
dmesg output:

[ 7794.674921] btmtk: Unknown symbol hci_cmd_sync_queue (err -2)
[ 7794.674942] btmtk: Unknown symbol hci_devcd_init (err -2)
[ 7794.674957] btmtk: Unknown symbol hci_devcd_complete (err -2)
[ 7794.674980] btmtk: Unknown symbol __hci_cmd_send (err -2)
[ 7794.674994] btmtk: Unknown symbol hci_devcd_register (err -2)
[ 7794.675006] btmtk: Unknown symbol hci_devcd_append (err -2)
[ 7794.675022] btmtk: Unknown symbol bt_info (err -2)
[ 7794.675034] btmtk: Unknown symbol bt_err (err -2)
[ 7794.675049] btmtk: Unknown symbol __hci_cmd_sync (err -2)

edit1:
I suspect it's the driver's problem not configured correctly or some configuration blocked that I can't find

edit2:
For more information:

sudo nano /etc/default/bluetooth.conf                                                       

BLUETOOTH_ENABLED=1
Autoenable=true
KeySize=0
RefreshDiscovery = true

sudo /usr/lib/bluetooth/bluetoothd -n -d

bluetoothd[14056]: Bluetooth daemon 5.75
bluetoothd[14056]: src/main.c:parse_config() parsing /etc/bluetooth/main.conf
bluetoothd[14056]: src/main.c:parse_config_string() General.Name = BlueZ
bluetoothd[14056]: src/adapter.c:adapter_init() Failed to access management interface
bluetoothd[14056]: src/main.c:main() Adapter handling initialization failed

edit3:
/etc/bluetooth/main.conf :

[General]

# Default adapter name
# Defaults to 'BlueZ X.YZ'
Name = BlueZ

# Default device class. Only the major and minor device class bits are
# considered. Defaults to '0x000000'.
#Class = 0x000100

# How long to stay in discoverable mode before going back to non-discoverable
# The value is in seconds. Default is 180, i.e. 3 minutes.
# 0 = disable timer, i.e. stay discoverable forever
#DiscoverableTimeout = 0

# Always allow pairing even if there are no agent registered
# Possible values: true, false
# Default: false
#AlwaysPairable = false

# How long to stay in pairable mode before going back to non-discoverable
# The value is in seconds. Default is 0.
# 0 = disable timer, i.e. stay pairable forever
#PairableTimeout = 0

# Use vendor id source (assigner), vendor, product and version information for
# DID profile support. The values are separated by ":" and assigner, VID, PID
# and version.
# Possible vendor id source values: bluetooth, usb (default) or false (disabled)
#DeviceID = bluetooth:1234:5678:abcd

# Do reverse service discovery for previously unknown devices that connect to
# us. For BR/EDR this option is really only needed for qualification since the
# BITE tester doesn't like us doing reverse SDP for some test cases, for LE
# this disables the GATT client functionally so it can be used in system which
# can only operate as peripheral (see also GATT Client option).
# Defaults to 'true'.
#ReverseServiceDiscovery = true

# Enable name resolving after inquiry. Set it to 'false' if you don't need
# remote devices name and want shorter discovery cycle. Defaults to 'true'.
#NameResolving = true

# Enable runtime persistency of debug link keys. Default is false which
# makes debug link keys valid only for the duration of the connection
# that they were created for.
#DebugKeys = false

# Restricts all controllers to the specified transport. Default value
# is "dual", i.e. both BR/EDR and LE enabled (when supported by the HW).
# Possible values: "dual", "bredr", "le"
#ControllerMode = dual

# Maximum number of controllers allowed to be exposed to the system.
# Default=0 (unlimited)
#MaxControllers=0

# Enables Multi Profile Specification support. This allows to specify if
# system supports only Multiple Profiles Single Device (MPSD) configuration
# or both Multiple Profiles Single Device (MPSD) and Multiple Profiles Multiple
# Devices (MPMD) configurations.
# Possible values: "off", "single", "multiple"
#MultiProfile = off

# Permanently enables the Fast Connectable setting for adapters that
# support it. When enabled other devices can connect faster to us,
# however the tradeoff is increased power consumptions. This feature
# will fully work only on kernel version 4.1 and newer. Defaults to
# 'false'.
#FastConnectable = false

# Default privacy setting.
# Enables use of private address.
# Possible values for LE mode: "off", "network/on", "device"
# Possible values for Dual mode: "off", "network/on", "device",
# "limited-network", "limited-device"
#
# - off: Local privacy disabled.
#
# - network/on: A device will only accept advertising packets from peer
# devices that contain private addresses. It may not be compatible with some
# legacy devices since it requires the use of RPA(s) all the time.
#
# - device: A device in device privacy mode is only concerned about the
# privacy of the device and will accept advertising packets from peer devices
# that contain their Identity Address as well as ones that contain a private
# address, even if the peer device has distributed its IRK in the past.

# - limited-network: Apply Limited Discoverable Mode to advertising, which
# follows the same policy as to BR/EDR that publishes the identity address when
# discoverable, and Network Privacy Mode for scanning.
#
# - limited-device: Apply Limited Discoverable Mode to advertising, which
# follows the same policy as to BR/EDR that publishes the identity address when
# discoverable, and Device Privacy Mode for scanning.
#
# Defaults to "off"
#Privacy = off

# Specify the policy to the JUST-WORKS repairing initiated by peer
# Possible values: "never", "confirm", "always"
# Defaults to "never"
#JustWorksRepairing = never

# How long to keep temporary devices around
# The value is in seconds. Default is 30.
# 0 = disable timer, i.e. never keep temporary devices
#TemporaryTimeout = 30

# Enables the device to issue an SDP request to update known services when
# profile is connected. Defaults to true.
#RefreshDiscovery = true

# Default Secure Connections setting.
# Enables the Secure Connections setting for adapters that support it. It
# provides better crypto algorithms for BT links and also enables CTKD (cross
# transport key derivation) during pairing on any link.
# Possible values: "off", "on", "only"
# - "off": Secure Connections are disabled
# - "on": Secure Connections are enabled when peer device supports them
# - "only": we allow only Secure Connections
# Defaults to "on"
#SecureConnections = on

# Enables D-Bus experimental interfaces
# Possible values: true or false
#Experimental = false

# Enables kernel experimental features, alternatively a list of UUIDs
# can be given.
# Possible values: true,false,<UUID List>
# Possible UUIDS:
# d4992530-b9ec-469f-ab01-6c481c47da1c (BlueZ Experimental Debug)
# 671b10b5-42c0-4696-9227-eb28d1b049d6 (BlueZ Experimental Simultaneous Central and Peripheral)
# 15c0a148-c273-11ea-b3de-0242ac130004 (BlueZ Experimental LL privacy)
# 330859bc-7506-492d-9370-9a6f0614037f (BlueZ Experimental Bluetooth Quality Report)
# a6695ace-ee7f-4fb9-881a-5fac66c629af (BlueZ Experimental Offload Codecs)
# 6fbaf188-05e0-496a-9885-d6ddfdb4e03e (BlueZ Experimental ISO socket)
# 69518c4c-b69f-4679-8bc1-c021b47b5733 (BlueZ Experimental Poll Errqueue)
# Defaults to false.
#KernelExperimental = false

# The duration to avoid retrying to resolve a peer's name, if the previous
# try failed.
# The value is in seconds. Default is 300, i.e. 5 minutes.
#RemoteNameRequestRetryDelay = 300

[BR]
# The following values are used to load default adapter parameters for BR/EDR.
# BlueZ loads the values into the kernel before the adapter is powered if the
# kernel supports the MGMT_LOAD_DEFAULT_PARAMETERS command. If a value isn't
# provided, the kernel will be initialized to it's default value.  The actual
# value will vary based on the kernel version and thus aren't provided here.
# The Bluetooth Core Specification should be consulted for the meaning and valid
# domain of each of these values.

# BR/EDR Page scan activity configuration
#PageScanType=
#PageScanInterval=
#PageScanWindow=

# BR/EDR Inquiry scan activity configuration
#InquiryScanType=
#InquiryScanInterval=
#InquiryScanWindow=

# BR/EDR Link supervision timeout
#LinkSupervisionTimeout=

# BR/EDR Page Timeout
#PageTimeout=

# BR/EDR Sniff Intervals
#MinSniffInterval=
#MaxSniffInterval=

[LE]
# The following values are used to load default adapter parameters for LE.
# BlueZ loads the values into the kernel before the adapter is powered if the
# kernel supports the MGMT_LOAD_DEFAULT_PARAMETERS command. If a value isn't
# provided, the kernel will be initialized to it's default value.  The actual
# value will vary based on the kernel version and thus aren't provided here.
# The Bluetooth Core Specification should be consulted for the meaning and valid
# domain of each of these values.
# LE advertisement interval (used for legacy advertisement interface only)
#MinAdvertisementInterval=
#MaxAdvertisementInterval=
#MultiAdvertisementRotationInterval=

# LE scanning parameters used for passive scanning supporting auto connect
# scenarios
#ScanIntervalAutoConnect=
#ScanWindowAutoConnect=

# LE scanning parameters used for passive scanning supporting wake from suspend
# scenarios
#ScanIntervalSuspend=
#ScanWindowSuspend=

# LE scanning parameters used for active scanning supporting discovery
# proceedure
#ScanIntervalDiscovery=
#ScanWindowDiscovery=

# LE scanning parameters used for passive scanning supporting the advertisement
# monitor Apis
#ScanIntervalAdvMonitor=
#ScanWindowAdvMonitor=

# LE scanning parameters used for connection establishment.
#ScanIntervalConnect=
#ScanWindowConnect=

# LE default connection parameters.  These values are superceeded by any
# specific values provided via the Load Connection Parameters interface
#MinConnectionInterval=
#MaxConnectionInterval=
#ConnectionLatency=
#ConnectionSupervisionTimeout=
#Autoconnecttimeout=

# Scan duration during interleaving scan. Only used when scanning for ADV
# monitors. The units are msec.
# Default: 300
#AdvMonAllowlistScanDuration=
# Default: 500
#AdvMonNoFilterScanDuration=

# Enable/Disable Advertisement Monitor interleave scan for power saving.
# 0: disable
# 1: enable
# Defaults to 1
#EnableAdvMonInterleaveScan=

[GATT]
# GATT attribute cache.
# Possible values:
# always: Always cache attributes even for devices not paired, this is
# recommended as it is best for interoperability, with more consistent
# reconnection times and enables proper tracking of notifications for all
# devices.
# yes: Only cache attributes of paired devices.
# no: Never cache attributes
# Default: always
#Cache = always

# Minimum required Encryption Key Size for accessing secured characteristics.
# Possible values: 0 and 7-16. 0 means don't care.
# Defaults to 0
#KeySize = 0

# Exchange MTU size.
# Possible values: 23-517
# Defaults to 517
#ExchangeMTU = 517

# Number of ATT channels
# Possible values: 1-5 (1 disables EATT)
# Default to 1
#Channels = 1

[CSIS]
# SIRK - Set Identification Resolution Key which is common for all the
# sets. They SIRK key is used to identify its sets. This can be any
# 128 bit value or a string value (e.g. product name) which is then hashed.
# Possible Values:
# 16 byte hexadecimal value: 861FAE703ED681F0C50B34155B6434FB
# String value: "My Product Name"
# Defaults to none
#SIRK =

# SIRK Encryption
# Possible values:
# true: Encrypt SIRK when read
# false: Do not encrypt SIRK when read. (plaintext)
# Defaults to true
#Encryption = true

# Total no of sets belongs to this Profile
# Defaults to 0
#Size = 0

# Rank for the device
# Defaults to 0
#Rank = 0

# This enables the GATT client functionally, so it can be disabled in system
# which can only operate as a peripheral.
# Defaults to 'true'.
#Client = true

[AVDTP]
# AVDTP L2CAP Signalling Channel Mode.
# Possible values:
# basic: Use L2CAP Basic Mode
# ertm: Use L2CAP Enhanced Retransmission Mode
#SessionMode = basic

# AVDTP L2CAP Transport Channel Mode.
# Possible values:
# basic: Use L2CAP Basic Mode
# streaming: Use L2CAP Streaming Mode
#StreamMode = basic

[Policy]
#
# The ReconnectUUIDs defines the set of remote services that should try
# to be reconnected to in case of a link loss (link supervision
# timeout). The policy plugin should contain a sane set of values by
# default, but this list can be overridden here. By setting the list to
# empty the reconnection feature gets disabled.
#ReconnectUUIDs=00001112-0000-1000-8000-00805f9b34fb,0000111f-0000-1000-8000-00805f9b34fb,0000110a-0000-1000-8000-00805f9b34fb,0000110b-0000-1000-8000-00805f9b34fb

# ReconnectAttempts define the number of attempts to reconnect after a link
# lost. Setting the value to 0 disables reconnecting feature.
#ReconnectAttempts=7

# ReconnectIntervals define the set of intervals in seconds to use in between
# attempts.
# If the number of attempts defined in ReconnectAttempts is bigger than the
# set of intervals the last interval is repeated until the last attempt.
#ReconnectIntervals=1,2,4,8,16,32,64

# AutoEnable defines option to enable all controllers when they are found.
# This includes adapters present on start as well as adapters that are plugged
# in later on. Defaults to 'true'.
#AutoEnable=true

# Audio devices that were disconnected due to suspend will be reconnected on
# resume. ResumeDelay determines the delay between when the controller
# resumes from suspend and a connection attempt is made. A longer delay is
# better for better co-existence with Wi-Fi.
# The value is in seconds.
# Default: 2
#ResumeDelay = 2

[AdvMon]
# Default RSSI Sampling Period. This is used when a client registers an
# advertisement monitor and leaves the RSSISamplingPeriod unset.
# Possible values:
# 0x00       Report all advertisements
# N = 0xXX   Report advertisements every N x 100 msec (range: 0x01 to 0xFE)
# 0xFF       Report only one advertisement per device during monitoring period
# Default: 0xFF
#RSSISamplingPeriod=0xFF 

edit 4:
Journactl -B (only selected necessary part for bluetooth problem)

 Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol hci_cmd_sync_queue (err -2)
Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol hci_devcd_init (err -2)
Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol hci_devcd_complete (err -2)
Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol __hci_cmd_send (err -2)
Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol hci_devcd_register (err -2)
Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol hci_devcd_append (err -2)
Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol bt_info (err -2)
Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol bt_err (err -2)
Apr 26 19:02:24 macbook kernel: btmtk: Unknown symbol __hci_cmd_sync (err -2)

edit 5:
journalctl -b -u bluetooth.service

Apr 26 16:51:22 macbook systemd[1]: Bluetooth service was skipped because of an unmet condition check (ConditionPathIsDirectory=/sys/class/bluetooth).
Apr 26 17:57:17 macbook systemd[1]: Bluetooth service was skipped because of an unmet condition check (ConditionPathIsDirectory=/sys/class/bluetooth).
Apr 26 19:10:28 macbook systemd[1]: Bluetooth service was skipped because of an unmet condition check (ConditionPathIsDirectory=/sys/class/bluetooth).
Apr 26 19:10:28 macbook systemd[1]: Bluetooth service was skipped because of an unmet condition check (ConditionPathIsDirectory=/sys/class/bluetooth).
Apr 26 19:29:32 macbook systemd[1]: Bluetooth service was skipped because of an unmet condition check (ConditionPathIsDirectory=/sys/class/bluetooth).
Apr 26 19:29:43 macbook systemd[1]: Bluetooth service was skipped because of an unmet condition check (ConditionPathIsDirectory=/sys/class/bluetooth).

edit 6:

bluetoothctl output:

Waiting to connect to bluetoothd...Unable to open mgmt_socket

edit 7:
somehow sudo modprobe btusb no longer giving error
but does not fix bluetooth service to start

edit 8:
sudo modprobe btusb does not give error before the sudo modprobe bluetooth is input into the terminal.
errors gives the same
sudo modprobe bluetooth
sudo modprobe btusb
modprobe: ERROR: could not insert 'btusb': Unknown symbol in module, or unknown parameter (see dmesg)

dmesg:
same error shown above

I guess its my only solution for it is to reinstall arch...

Solved

Last edited by Jakie121 (2024-05-05 08:43:12)